summaryrefslogtreecommitdiff
path: root/drivers/pci/controller/pci-mvebu.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/pci/controller/pci-mvebu.c')
-rw-r--r--drivers/pci/controller/pci-mvebu.c251
1 files changed, 209 insertions, 42 deletions
diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c
index 2dc6890dbcaa..2a3bf82aa4e2 100644
--- a/drivers/pci/controller/pci-mvebu.c
+++ b/drivers/pci/controller/pci-mvebu.c
@@ -51,10 +51,14 @@
PCIE_CONF_FUNC(PCI_FUNC(devfn)) | PCIE_CONF_REG(where) | \
PCIE_CONF_ADDR_EN)
#define PCIE_CONF_DATA_OFF 0x18fc
+#define PCIE_INT_CAUSE_OFF 0x1900
+#define PCIE_INT_PM_PME BIT(28)
#define PCIE_MASK_OFF 0x1910
#define PCIE_MASK_ENABLE_INTS 0x0f000000
#define PCIE_CTRL_OFF 0x1a00
#define PCIE_CTRL_X1_MODE 0x0001
+#define PCIE_CTRL_RC_MODE BIT(1)
+#define PCIE_CTRL_MASTER_HOT_RESET BIT(24)
#define PCIE_STAT_OFF 0x1a04
#define PCIE_STAT_BUS 0xff00
#define PCIE_STAT_DEV 0x1f0000
@@ -125,6 +129,11 @@ static bool mvebu_pcie_link_up(struct mvebu_pcie_port *port)
return !(mvebu_readl(port, PCIE_STAT_OFF) & PCIE_STAT_LINK_DOWN);
}
+static u8 mvebu_pcie_get_local_bus_nr(struct mvebu_pcie_port *port)
+{
+ return (mvebu_readl(port, PCIE_STAT_OFF) & PCIE_STAT_BUS) >> 8;
+}
+
static void mvebu_pcie_set_local_bus_nr(struct mvebu_pcie_port *port, int nr)
{
u32 stat;
@@ -213,18 +222,21 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port)
static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)
{
- u32 cmd, mask;
+ u32 ctrl, cmd, mask;
- /* Point PCIe unit MBUS decode windows to DRAM space. */
- mvebu_pcie_setup_wins(port);
+ /* Setup PCIe controller to Root Complex mode. */
+ ctrl = mvebu_readl(port, PCIE_CTRL_OFF);
+ ctrl |= PCIE_CTRL_RC_MODE;
+ mvebu_writel(port, ctrl, PCIE_CTRL_OFF);
- /* Master + slave enable. */
+ /* Disable Root Bridge I/O space, memory space and bus mastering. */
cmd = mvebu_readl(port, PCIE_CMD_OFF);
- cmd |= PCI_COMMAND_IO;
- cmd |= PCI_COMMAND_MEMORY;
- cmd |= PCI_COMMAND_MASTER;
+ cmd &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
mvebu_writel(port, cmd, PCIE_CMD_OFF);
+ /* Point PCIe unit MBUS decode windows to DRAM space. */
+ mvebu_pcie_setup_wins(port);
+
/* Enable interrupt lines A-D. */
mask = mvebu_readl(port, PCIE_MASK_OFF);
mask |= PCIE_MASK_ENABLE_INTS;
@@ -371,8 +383,7 @@ static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
/* Are the new iobase/iolimit values invalid? */
if (conf->iolimit < conf->iobase ||
- conf->iolimitupper < conf->iobaseupper ||
- !(conf->command & PCI_COMMAND_IO)) {
+ conf->iolimitupper < conf->iobaseupper) {
mvebu_pcie_set_window(port, port->io_target, port->io_attr,
&desired, &port->iowin);
return;
@@ -409,8 +420,7 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
struct pci_bridge_emul_conf *conf = &port->bridge.conf;
/* Are the new membase/memlimit values invalid? */
- if (conf->memlimit < conf->membase ||
- !(conf->command & PCI_COMMAND_MEMORY)) {
+ if (conf->memlimit < conf->membase) {
mvebu_pcie_set_window(port, port->mem_target, port->mem_attr,
&desired, &port->memwin);
return;
@@ -431,6 +441,54 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
}
static pci_bridge_emul_read_status_t
+mvebu_pci_bridge_emul_base_conf_read(struct pci_bridge_emul *bridge,
+ int reg, u32 *value)
+{
+ struct mvebu_pcie_port *port = bridge->data;
+
+ switch (reg) {
+ case PCI_COMMAND:
+ *value = mvebu_readl(port, PCIE_CMD_OFF);
+ break;
+
+ case PCI_PRIMARY_BUS: {
+ /*
+ * From the whole 32bit register we support reading from HW only
+ * secondary bus number which is mvebu local bus number.
+ * Other bits are retrieved only from emulated config buffer.
+ */
+ __le32 *cfgspace = (__le32 *)&bridge->conf;
+ u32 val = le32_to_cpu(cfgspace[PCI_PRIMARY_BUS / 4]);
+ val &= ~0xff00;
+ val |= mvebu_pcie_get_local_bus_nr(port) << 8;
+ *value = val;
+ break;
+ }
+
+ case PCI_INTERRUPT_LINE: {
+ /*
+ * From the whole 32bit register we support reading from HW only
+ * one bit: PCI_BRIDGE_CTL_BUS_RESET.
+ * Other bits are retrieved only from emulated config buffer.
+ */
+ __le32 *cfgspace = (__le32 *)&bridge->conf;
+ u32 val = le32_to_cpu(cfgspace[PCI_INTERRUPT_LINE / 4]);
+ if (mvebu_readl(port, PCIE_CTRL_OFF) & PCIE_CTRL_MASTER_HOT_RESET)
+ val |= PCI_BRIDGE_CTL_BUS_RESET << 16;
+ else
+ val &= ~(PCI_BRIDGE_CTL_BUS_RESET << 16);
+ *value = val;
+ break;
+ }
+
+ default:
+ return PCI_BRIDGE_EMUL_NOT_HANDLED;
+ }
+
+ return PCI_BRIDGE_EMUL_HANDLED;
+}
+
+static pci_bridge_emul_read_status_t
mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,
int reg, u32 *value)
{
@@ -442,9 +500,7 @@ mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,
break;
case PCI_EXP_DEVCTL:
- *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL) &
- ~(PCI_EXP_DEVCTL_URRE | PCI_EXP_DEVCTL_FERE |
- PCI_EXP_DEVCTL_NFERE | PCI_EXP_DEVCTL_CERE);
+ *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL);
break;
case PCI_EXP_LNKCAP:
@@ -468,6 +524,18 @@ mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,
*value = mvebu_readl(port, PCIE_RC_RTSTA);
break;
+ case PCI_EXP_DEVCAP2:
+ *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCAP2);
+ break;
+
+ case PCI_EXP_DEVCTL2:
+ *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL2);
+ break;
+
+ case PCI_EXP_LNKCTL2:
+ *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_LNKCTL2);
+ break;
+
default:
return PCI_BRIDGE_EMUL_NOT_HANDLED;
}
@@ -484,26 +552,16 @@ mvebu_pci_bridge_emul_base_conf_write(struct pci_bridge_emul *bridge,
switch (reg) {
case PCI_COMMAND:
- {
- if (!mvebu_has_ioport(port))
- conf->command &= ~PCI_COMMAND_IO;
-
- if ((old ^ new) & PCI_COMMAND_IO)
- mvebu_pcie_handle_iobase_change(port);
- if ((old ^ new) & PCI_COMMAND_MEMORY)
- mvebu_pcie_handle_membase_change(port);
+ if (!mvebu_has_ioport(port)) {
+ conf->command = cpu_to_le16(
+ le16_to_cpu(conf->command) & ~PCI_COMMAND_IO);
+ new &= ~PCI_COMMAND_IO;
+ }
+ mvebu_writel(port, new, PCIE_CMD_OFF);
break;
- }
case PCI_IO_BASE:
- /*
- * We keep bit 1 set, it is a read-only bit that
- * indicates we support 32 bits addressing for the
- * I/O
- */
- conf->iobase |= PCI_IO_RANGE_TYPE_32;
- conf->iolimit |= PCI_IO_RANGE_TYPE_32;
mvebu_pcie_handle_iobase_change(port);
break;
@@ -516,7 +574,19 @@ mvebu_pci_bridge_emul_base_conf_write(struct pci_bridge_emul *bridge,
break;
case PCI_PRIMARY_BUS:
- mvebu_pcie_set_local_bus_nr(port, conf->secondary_bus);
+ if (mask & 0xff00)
+ mvebu_pcie_set_local_bus_nr(port, conf->secondary_bus);
+ break;
+
+ case PCI_INTERRUPT_LINE:
+ if (mask & (PCI_BRIDGE_CTL_BUS_RESET << 16)) {
+ u32 ctrl = mvebu_readl(port, PCIE_CTRL_OFF);
+ if (new & (PCI_BRIDGE_CTL_BUS_RESET << 16))
+ ctrl |= PCIE_CTRL_MASTER_HOT_RESET;
+ else
+ ctrl &= ~PCIE_CTRL_MASTER_HOT_RESET;
+ mvebu_writel(port, ctrl, PCIE_CTRL_OFF);
+ }
break;
default:
@@ -532,13 +602,6 @@ mvebu_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge,
switch (reg) {
case PCI_EXP_DEVCTL:
- /*
- * Armada370 data says these bits must always
- * be zero when in root complex mode.
- */
- new &= ~(PCI_EXP_DEVCTL_URRE | PCI_EXP_DEVCTL_FERE |
- PCI_EXP_DEVCTL_NFERE | PCI_EXP_DEVCTL_CERE);
-
mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL);
break;
@@ -555,12 +618,31 @@ mvebu_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge,
break;
case PCI_EXP_RTSTA:
- mvebu_writel(port, new, PCIE_RC_RTSTA);
+ /*
+ * PME Status bit in Root Status Register (PCIE_RC_RTSTA)
+ * is read-only and can be cleared only by writing 0b to the
+ * Interrupt Cause RW0C register (PCIE_INT_CAUSE_OFF). So
+ * clear PME via Interrupt Cause.
+ */
+ if (new & PCI_EXP_RTSTA_PME)
+ mvebu_writel(port, ~PCIE_INT_PM_PME, PCIE_INT_CAUSE_OFF);
+ break;
+
+ case PCI_EXP_DEVCTL2:
+ mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL2);
+ break;
+
+ case PCI_EXP_LNKCTL2:
+ mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_LNKCTL2);
+ break;
+
+ default:
break;
}
}
static struct pci_bridge_emul_ops mvebu_pci_bridge_emul_ops = {
+ .read_base = mvebu_pci_bridge_emul_base_conf_read,
.write_base = mvebu_pci_bridge_emul_base_conf_write,
.read_pcie = mvebu_pci_bridge_emul_pcie_conf_read,
.write_pcie = mvebu_pci_bridge_emul_pcie_conf_write,
@@ -570,7 +652,7 @@ static struct pci_bridge_emul_ops mvebu_pci_bridge_emul_ops = {
* Initialize the configuration space of the PCI-to-PCI bridge
* associated with the given PCIe interface.
*/
-static void mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port)
+static int mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port)
{
struct pci_bridge_emul *bridge = &port->bridge;
u32 pcie_cap = mvebu_readl(port, PCIE_CAP_PCIEXP);
@@ -597,7 +679,7 @@ static void mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port)
bridge->data = port;
bridge->ops = &mvebu_pci_bridge_emul_ops;
- pci_bridge_emul_init(bridge, PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR);
+ return pci_bridge_emul_init(bridge, PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR);
}
static inline struct mvebu_pcie *sys_to_pcie(struct pci_sys_data *sys)
@@ -1120,9 +1202,94 @@ static int mvebu_pcie_probe(struct platform_device *pdev)
continue;
}
+ ret = mvebu_pci_bridge_emul_init(port);
+ if (ret < 0) {
+ dev_err(dev, "%s: cannot init emulated bridge\n",
+ port->name);
+ devm_iounmap(dev, port->base);
+ port->base = NULL;
+ mvebu_pcie_powerdown(port);
+ continue;
+ }
+
+ /*
+ * PCIe topology exported by mvebu hw is quite complicated. In
+ * reality has something like N fully independent host bridges
+ * where each host bridge has one PCIe Root Port (which acts as
+ * PCI Bridge device). Each host bridge has its own independent
+ * internal registers, independent access to PCI config space,
+ * independent interrupt lines, independent window and memory
+ * access configuration. But additionally there is some kind of
+ * peer-to-peer support between PCIe devices behind different
+ * host bridges limited just to forwarding of memory and I/O
+ * transactions (forwarding of error messages and config cycles
+ * is not supported). So we could say there are N independent
+ * PCIe Root Complexes.
+ *
+ * For this kind of setup DT should have been structured into
+ * N independent PCIe controllers / host bridges. But instead
+ * structure in past was defined to put PCIe Root Ports of all
+ * host bridges into one bus zero, like in classic multi-port
+ * Root Complex setup with just one host bridge.
+ *
+ * This means that pci-mvebu.c driver provides "virtual" bus 0
+ * on which registers all PCIe Root Ports (PCI Bridge devices)
+ * specified in DT by their BDF addresses and virtually routes
+ * PCI config access of each PCI bridge device to specific PCIe
+ * host bridge.
+ *
+ * Normally PCI Bridge should choose between Type 0 and Type 1
+ * config requests based on primary and secondary bus numbers
+ * configured on the bridge itself. But because mvebu PCI Bridge
+ * does not have registers for primary and secondary bus numbers
+ * in its config space, it determinates type of config requests
+ * via its own custom way.
+ *
+ * There are two options how mvebu determinate type of config
+ * request.
+ *
+ * 1. If Secondary Bus Number Enable bit is not set or is not
+ * available (applies for pre-XP PCIe controllers) then Type 0
+ * is used if target bus number equals Local Bus Number (bits
+ * [15:8] in register 0x1a04) and target device number differs
+ * from Local Device Number (bits [20:16] in register 0x1a04).
+ * Type 1 is used if target bus number differs from Local Bus
+ * Number. And when target bus number equals Local Bus Number
+ * and target device equals Local Device Number then request is
+ * routed to Local PCI Bridge (PCIe Root Port).
+ *
+ * 2. If Secondary Bus Number Enable bit is set (bit 7 in
+ * register 0x1a2c) then mvebu hw determinate type of config
+ * request like compliant PCI Bridge based on primary bus number
+ * which is configured via Local Bus Number (bits [15:8] in
+ * register 0x1a04) and secondary bus number which is configured
+ * via Secondary Bus Number (bits [7:0] in register 0x1a2c).
+ * Local PCI Bridge (PCIe Root Port) is available on primary bus
+ * as device with Local Device Number (bits [20:16] in register
+ * 0x1a04).
+ *
+ * Secondary Bus Number Enable bit is disabled by default and
+ * option 2. is not available on pre-XP PCIe controllers. Hence
+ * this driver always use option 1.
+ *
+ * Basically it means that primary and secondary buses shares
+ * one virtual number configured via Local Bus Number bits and
+ * Local Device Number bits determinates if accessing primary
+ * or secondary bus. Set Local Device Number to 1 and redirect
+ * all writes of PCI Bridge Secondary Bus Number register to
+ * Local Bus Number (bits [15:8] in register 0x1a04).
+ *
+ * So when accessing devices on buses behind secondary bus
+ * number it would work correctly. And also when accessing
+ * device 0 at secondary bus number via config space would be
+ * correctly routed to secondary bus. Due to issues described
+ * in mvebu_pcie_setup_hw(), PCI Bridges at primary bus (zero)
+ * are not accessed directly via PCI config space but rarher
+ * indirectly via kernel emulated PCI bridge driver.
+ */
mvebu_pcie_setup_hw(port);
mvebu_pcie_set_local_dev_nr(port, 1);
- mvebu_pci_bridge_emul_init(port);
+ mvebu_pcie_set_local_bus_nr(port, 0);
}
pcie->nports = i;
generated by cgit v1.2.3 (git 2.39.0) at 2024-06-02 14:22:14 +0300