| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This is the 5.10.46 stable release.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
It replaces timer callback with delayed work to avoid deadlock.
Tested: Passed over weekend stress test.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
Change-Id: I123cacabe7c1a5988f6356deeee03a6996b87141
|
|
The values were determined experimentally via boot tests, not by
measuring the bus behaviour with a scope. We plan to do scope
measurements to confirm or refine the values and will update the
devicetree if necessary once these have been obtained.
However, with the patch we can write and read data without issue, where
as booting the system without the patch failed at the point of mounting
the rootfs.
OpenBMC-Staging-Count: 1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210628013605.1257346-1-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The degree values were reversed out from the magic tap values of 7 (in)
and 15 + inversion (out) initially suggested by Aspeed.
With the patch tacoma survives several gigabytes of reads and writes
using dd while without it locks up randomly during the boot process.
OpenBMC-Staging-Count: 1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210625061017.1149942-1-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This is the 5.10.46 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Rainier uses KCS channel 2 as the source for the debug-trigger
application outlined at [1] and implemented at [2].
[1] https://github.com/openbmc/docs/blob/master/designs/bmc-service-failure-debug-and-recovery.md
[2] https://github.com/openbmc/debug-trigger
OpenBMC-Staging-Count: 1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210623033854.587464-8-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The reset state of the status bits on KCS 4 is inappropriate for the
MCTP LPC binding. Switch to KCS 3 which has a different reset behaviour.
OpenBMC-Staging-Count: 1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210623033854.587464-7-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The mctp-lpc chardev is replaced (temporarily) by the raw KCS chardev.
The raw chardev is required for IBM's purposes until Jeremy's
socket-based MCTP patches are merged[1][2].
[1] https://github.com/openbmc/docs/blob/master/designs/mctp/mctp-kernel.md
[2] https://lore.kernel.org/openbmc/f4f5fa66542401e8d5e78c1fb30153195d384b62.camel@codeconstruct.com.au/
OpenBMC-Staging-Count: 1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210623033854.587464-6-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The MCTP LPC driver was loaded by hacking up the compatible in the
devicetree node for KCS 4. With the introduction of the raw KCS driver
this hack is no-longer required. Use the regular compatible string for
KCS 4 and configure the appropriate SerIRQ.
OpenBMC-Staging-Count: 1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210623033854.587464-5-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The raw KCS chardev is used by libmctp's vendor-defined LPC binding.
OpenBMC-Staging-Count: 1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210623033854.587464-4-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The existing IPMI chardev encodes IPMI behaviours as the name suggests.
However, KCS devices are useful beyond IPMI (or keyboards), as they
provide a means to generate IRQs and exchange arbitrary data between a
BMC and its host system.
Implement a "raw" KCS character device that exposes the IDR, ODR and STR
registers to userspace via read() and write() implemented on a character
device:
+--------+--------+---------+
| Offset | read() | write() |
+--------+--------+---------+
| 0 | IDR | ODR |
+--------+--------+---------+
| 1 | STR | STR |
+--------+--------+---------+
This interface allows userspace to implement arbitrary (though somewhat
inefficient) protocols for exchanging information between a BMC and host
firmware. Conceptually the KCS interface can be used as an out-of-band
mechanism for interrupt-signaled control messages while bulk data
transfers occur over more appropriate interfaces between the BMC and the
host (which may lack their own interrupt mechanism, e.g. LPC FW cycles).
poll() is provided, which will wait for IBF or OBE conditions for data
reads and writes respectively. Reads of STR on its own never blocks,
though accessing both offsets in the one system call may block if the
data registers are not ready.
OpenBMC-Staging-Count: 1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210623033854.587464-3-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The comparisons of the unsigned int hw_type to less than zero always
false because it is unsigned. Fix this by using an int for the
assignment and less than zero check.
OpenBMC-Staging-Count: 1
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: 9d2df9a0ad80 ("ipmi: kcs_bmc_aspeed: Implement KCS SerIRQ configuration")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Message-Id: <20210616162913.15259-1-colin.king@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Link: https://lore.kernel.org/r/20210623033854.587464-2-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Tacoma and Rainier both have a line-names array that is too long:
gpio gpiochip0: gpio-line-names is length 232 but should be at most length 208
This was probably copied from an AST2500 device tree that did have more
GPIOs on the controller.
OpenBMC-Staging-Count: 1
Fixes: e9b24b55ca4f ("ARM: dts: aspeed: rainier: Add gpio line names")
Fixes: 2f68e4e7df67 ("ARM: dts: aspeed: tacoma: Add gpio line names")
Link: https://lore.kernel.org/r/20210624090742.56640-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Remove the gpio-keys entries for the power supply presence lines from
the Rainier device tree. The user space applications are going to change
from using libevdev to libgpiod.
OpenBMC-Staging-Count: 1
Signed-off-by: B. J. Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20210623230401.3050076-1-bjwyman@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Determined by scope measurements at speed.
OpenBMC-Staging-Count: 1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201208012615.2717412-7-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Link: https://lore.kernel.org/r/20210621154911.244649123@linuxfoundation.org
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Jason Self <jason@bluehome.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Salvatore Bonaccorso <carnil@debian.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Hulk Robot <hulkrobot@huawei.com>
Tested-by: Rudi Heitbaum <rudi@heitbaum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4bf584a03eec674975ee9fe36c8583d9d470dab1 upstream.
When do system reboot, it calls dwc3_shutdown and the whole debugfs
for dwc3 has removed first, when the gadget tries to do deinit, and
remove debugfs for its endpoints, it meets NULL pointer dereference
issue when call debugfs_lookup. Fix it by removing the whole dwc3
debugfs later than dwc3_drd_exit.
[ 2924.958838] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000002
....
[ 2925.030994] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--)
[ 2925.037005] pc : inode_permission+0x2c/0x198
[ 2925.041281] lr : lookup_one_len_common+0xb0/0xf8
[ 2925.045903] sp : ffff80001276ba70
[ 2925.049218] x29: ffff80001276ba70 x28: ffff0000c01f0000 x27: 0000000000000000
[ 2925.056364] x26: ffff800011791e70 x25: 0000000000000008 x24: dead000000000100
[ 2925.063510] x23: dead000000000122 x22: 0000000000000000 x21: 0000000000000001
[ 2925.070652] x20: ffff8000122c6188 x19: 0000000000000000 x18: 0000000000000000
[ 2925.077797] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000004
[ 2925.084943] x14: ffffffffffffffff x13: 0000000000000000 x12: 0000000000000030
[ 2925.092087] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f x9 : ffff8000102b2420
[ 2925.099232] x8 : 7f7f7f7f7f7f7f7f x7 : feff73746e2f6f64 x6 : 0000000000008080
[ 2925.106378] x5 : 61c8864680b583eb x4 : 209e6ec2d263dbb7 x3 : 000074756f307065
[ 2925.113523] x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff8000122c6188
[ 2925.120671] Call trace:
[ 2925.123119] inode_permission+0x2c/0x198
[ 2925.127042] lookup_one_len_common+0xb0/0xf8
[ 2925.131315] lookup_one_len_unlocked+0x34/0xb0
[ 2925.135764] lookup_positive_unlocked+0x14/0x50
[ 2925.140296] debugfs_lookup+0x68/0xa0
[ 2925.143964] dwc3_gadget_free_endpoints+0x84/0xb0
[ 2925.148675] dwc3_gadget_exit+0x28/0x78
[ 2925.152518] dwc3_drd_exit+0x100/0x1f8
[ 2925.156267] dwc3_remove+0x11c/0x120
[ 2925.159851] dwc3_shutdown+0x14/0x20
[ 2925.163432] platform_shutdown+0x28/0x38
[ 2925.167360] device_shutdown+0x15c/0x378
[ 2925.171291] kernel_restart_prepare+0x3c/0x48
[ 2925.175650] kernel_restart+0x1c/0x68
[ 2925.179316] __do_sys_reboot+0x218/0x240
[ 2925.183247] __arm64_sys_reboot+0x28/0x30
[ 2925.187262] invoke_syscall+0x48/0x100
[ 2925.191017] el0_svc_common.constprop.0+0x48/0xc8
[ 2925.195726] do_el0_svc+0x28/0x88
[ 2925.199045] el0_svc+0x20/0x30
[ 2925.202104] el0_sync_handler+0xa8/0xb0
[ 2925.205942] el0_sync+0x148/0x180
[ 2925.209270] Code: a9025bf5 2a0203f5 121f0056 370802b5 (79400660)
[ 2925.215372] ---[ end trace 124254d8e485a58b ]---
[ 2925.220012] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 2925.227676] Kernel Offset: disabled
[ 2925.231164] CPU features: 0x00001001,20000846
[ 2925.235521] Memory Limit: none
[ 2925.238580] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]---
Fixes: 8d396bb0a5b6 ("usb: dwc3: debugfs: Add and remove endpoint dirs dynamically")
Cc: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20210608105656.10795-1-peter.chen@kernel.org
(cherry picked from commit 2a042767814bd0edf2619f06fecd374e266ea068)
Link: https://lore.kernel.org/r/20210615080847.GA10432@jackp-linux.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d396bb0a5b62b326f6be7594d8bd46b088296bd upstream.
The DWC3 DebugFS directory and files are currently created once
during probe. This includes creation of subdirectories for each
of the gadget's endpoints. This works fine for peripheral-only
controllers, as dwc3_core_init_mode() calls dwc3_gadget_init()
just prior to calling dwc3_debugfs_init().
However, for dual-role controllers, dwc3_core_init_mode() will
instead call dwc3_drd_init() which is problematic in a few ways.
First, the initial state must be determined, then dwc3_set_mode()
will have to schedule drd_work and by then dwc3_debugfs_init()
could have already been invoked. Even if the initial mode is
peripheral, dwc3_gadget_init() happens after the DebugFS files
are created, and worse so if the initial state is host and the
controller switches to peripheral much later. And secondly,
even if the gadget endpoints' debug entries were successfully
created, if the controller exits peripheral mode, its dwc3_eps
are freed so the debug files would now hold stale references.
So it is best if the DebugFS endpoint entries are created and
removed dynamically at the same time the underlying dwc3_eps are.
Do this by calling dwc3_debugfs_create_endpoint_dir() as each
endpoint is created, and conversely remove the DebugFS entry when
the endpoint is freed.
Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210529192932.22912-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef83f9efe8461b8fd71eb60b53dbb6a5dd7b39e9 upstream.
To pick the changes in:
ea6932d70e223e02 ("net: make get_net_ns return error if NET_NS is disabled")
That don't result in any changes in the tables generated from that
header.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/perf/trace/beauty/include/linux/socket.h' differs from latest version at 'include/linux/socket.h'
diff -u tools/perf/trace/beauty/include/linux/socket.h include/linux/socket.h
Cc: Changbin Du <changbin.du@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1792a59eab9593de2eae36c40c5a22d70f52c026 upstream.
To pick the changes in:
321827477360934d ("icmp: don't send out ICMP messages with a source address of 0.0.0.0")
That don't result in any change in tooling, as INADDR_ are not used to
generate id->string tables used by 'perf trace'.
This addresses this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h
Cc: David S. Miller <davem@davemloft.net>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb3cefe3f3f8af27c6076ef7d1f00350f502055d upstream.
Add clock rate zero check to fix coverity issue of "divide by 0".
Fixes: commit 85bd1798b24a ("net: fec: fix spin_lock dead lock")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f269102baf788aecfcbbc6313b6bceb54c9b990 upstream.
Platform drivers may call stmmac_probe_config_dt() to parse dt, could
call stmmac_remove_config_dt() in error handing after dt parsed, so need
disable clocks in stmmac_remove_config_dt().
Go through all platforms drivers which use stmmac_probe_config_dt(),
none of them disable clocks manually, so it's safe to disable them in
stmmac_remove_config_dt().
Fixes: commit d2ed0a7755fe ("net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1b3865d016815cbd69a1879ca1c8a8901fda1072 upstream.
Fixes build with CONFIG_SLAB_FREELIST_HARDENED=y.
Hopefully. But it's the right thing to do anwyay.
Fixes: 1ad53d9fa3f61 ("slub: improve bit diffusion for freelist ptr obfuscation")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213417
Reported-by: <vannguye@cisco.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e41a49fadbc80b60b48d3c095d9e2ee7ef7c9a8e upstream.
It turns out that SLUB redzoning ("slub_debug=Z") checks from
s->object_size rather than from s->inuse (which is normally bumped to
make room for the freelist pointer), so a cache created with an object
size less than 24 would have the freelist pointer written beyond
s->object_size, causing the redzone to be corrupted by the freelist
pointer. This was very visible with "slub_debug=ZF":
BUG test (Tainted: G B ): Right Redzone overwritten
-----------------------------------------------------------------------------
INFO: 0xffff957ead1c05de-0xffff957ead1c05df @offset=1502. First byte 0x1a instead of 0xbb
INFO: Slab 0xffffef3950b47000 objects=170 used=170 fp=0x0000000000000000 flags=0x8000000000000200
INFO: Object 0xffff957ead1c05d8 @offset=1496 fp=0xffff957ead1c0620
Redzone (____ptrval____): bb bb bb bb bb bb bb bb ........
Object (____ptrval____): 00 00 00 00 00 f6 f4 a5 ........
Redzone (____ptrval____): 40 1d e8 1a aa @....
Padding (____ptrval____): 00 00 00 00 00 00 00 00 ........
Adjust the offset to stay within s->object_size.
(Note that no caches of in this size range are known to exist in the
kernel currently.)
Link: https://lkml.kernel.org/r/20210608183955.280836-4-keescook@chromium.org
Link: https://lore.kernel.org/linux-mm/20200807160627.GA1420741@elver.google.com/
Link: https://lore.kernel.org/lkml/0f7dd7b2-7496-5e2d-9488-2ec9f8e90441@suse.cz/Fixes: 89b83f282d8b (slub: avoid redzone when choosing freepointer location)
Link: https://lore.kernel.org/lkml/CANpmjNOwZ5VpKQn+SYWovTkFB4VsT-RPwyENBmaK0dLcpqStkA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Marco Elver <elver@google.com>
Reported-by: "Lin, Zhenpeng" <zplin@psu.edu>
Tested-by: Marco Elver <elver@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 74c1d3e081533825f2611e46edea1fcdc0701985 upstream.
The redzone area for SLUB exists between s->object_size and s->inuse
(which is at least the word-aligned object_size). If a cache were
created with an object_size smaller than sizeof(void *), the in-object
stored freelist pointer would overwrite the redzone (e.g. with boot
param "slub_debug=ZF"):
BUG test (Tainted: G B ): Right Redzone overwritten
-----------------------------------------------------------------------------
INFO: 0xffff957ead1c05de-0xffff957ead1c05df @offset=1502. First byte 0x1a instead of 0xbb
INFO: Slab 0xffffef3950b47000 objects=170 used=170 fp=0x0000000000000000 flags=0x8000000000000200
INFO: Object 0xffff957ead1c05d8 @offset=1496 fp=0xffff957ead1c0620
Redzone (____ptrval____): bb bb bb bb bb bb bb bb ........
Object (____ptrval____): f6 f4 a5 40 1d e8 ...@..
Redzone (____ptrval____): 1a aa ..
Padding (____ptrval____): 00 00 00 00 00 00 00 00 ........
Store the freelist pointer out of line when object_size is smaller than
sizeof(void *) and redzoning is enabled.
Additionally remove the "smaller than sizeof(void *)" check under
CONFIG_DEBUG_VM in kmem_cache_sanity_check() as it is now redundant:
SLAB and SLOB both handle small sizes.
(Note that no caches within this size range are known to exist in the
kernel currently.)
Link: https://lkml.kernel.org/r/20210608183955.280836-3-keescook@chromium.org
Fixes: 81819f0fc828 ("SLUB core")
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: "Lin, Zhenpeng" <zplin@psu.edu>
Cc: Marco Elver <elver@google.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8669dbab2ae56085c128894b181c2aa50f97e368 upstream.
Patch series "Actually fix freelist pointer vs redzoning", v4.
This fixes redzoning vs the freelist pointer (both for middle-position
and very small caches). Both are "theoretical" fixes, in that I see no
evidence of such small-sized caches actually be used in the kernel, but
that's no reason to let the bugs continue to exist, especially since
people doing local development keep tripping over it. :)
This patch (of 3):
Instead of repeating "Redzone" and "Poison", clarify which sides of
those zones got tripped. Additionally fix column alignment in the
trailer.
Before:
BUG test (Tainted: G B ): Redzone overwritten
...
Redzone (____ptrval____): bb bb bb bb bb bb bb bb ........
Object (____ptrval____): f6 f4 a5 40 1d e8 ...@..
Redzone (____ptrval____): 1a aa ..
Padding (____ptrval____): 00 00 00 00 00 00 00 00 ........
After:
BUG test (Tainted: G B ): Right Redzone overwritten
...
Redzone (____ptrval____): bb bb bb bb bb bb bb bb ........
Object (____ptrval____): f6 f4 a5 40 1d e8 ...@..
Redzone (____ptrval____): 1a aa ..
Padding (____ptrval____): 00 00 00 00 00 00 00 00 ........
The earlier commits that slowly resulted in the "Before" reporting were:
d86bd1bece6f ("mm/slub: support left redzone")
ffc79d288000 ("slub: use print_hex_dump")
2492268472e7 ("SLUB: change error reporting format to follow lockdep loosely")
Link: https://lkml.kernel.org/r/20210608183955.280836-1-keescook@chromium.org
Link: https://lkml.kernel.org/r/20210608183955.280836-2-keescook@chromium.org
Link: https://lore.kernel.org/lkml/cfdb11d7-fb8e-e578-c939-f7f5fb69a6bd@suse.cz/
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Marco Elver <elver@google.com>
Cc: "Lin, Zhenpeng" <zplin@psu.edu>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 099dd6878b9b12d6bbfa6bf29ce0c8ddd38f6901 upstream.
I found it by pure code review, that pte_same_as_swp() of unuse_vma()
didn't take uffd-wp bit into account when comparing ptes.
pte_same_as_swp() returning false negative could cause failure to
swapoff swap ptes that was wr-protected by userfaultfd.
Link: https://lkml.kernel.org/r/20210603180546.9083-1-peterx@redhat.com
Fixes: f45ec5ff16a7 ("userfaultfd: wp: support swap and page migration")
Signed-off-by: Peter Xu <peterx@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org> [5.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cfc579f9d89af4ada58c69b03bcaa4887840f3b3 upstream.
The egress tunnel code uses dst_clone() and directly sets the result
which is wrong because the entry might have 0 refcnt or be already deleted,
causing number of problems. It also triggers the WARN_ON() in dst_hold()[1]
when a refcnt couldn't be taken. Fix it by using dst_hold_safe() and
checking if a reference was actually taken before setting the dst.
[1] dmesg WARN_ON log and following refcnt errors
WARNING: CPU: 5 PID: 38 at include/net/dst.h:230 br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge]
Modules linked in: 8021q garp mrp bridge stp llc bonding ipv6 virtio_net
CPU: 5 PID: 38 Comm: ksoftirqd/5 Kdump: loaded Tainted: G W 5.13.0-rc3+ #360
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
RIP: 0010:br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge]
Code: e8 85 bc 01 e1 45 84 f6 74 90 45 31 f6 85 db 48 c7 c7 a0 02 19 a0 41 0f 94 c6 31 c9 31 d2 44 89 f6 e8 64 bc 01 e1 85 db 75 02 <0f> 0b 31 c9 31 d2 44 89 f6 48 c7 c7 70 02 19 a0 e8 4b bc 01 e1 49
RSP: 0018:ffff8881003d39e8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffffffa01902a0
RBP: ffff8881040c6700 R08: 0000000000000000 R09: 0000000000000001
R10: 2ce93d0054fe0d00 R11: 54fe0d00000e0000 R12: ffff888109515000
R13: 0000000000000000 R14: 0000000000000001 R15: 0000000000000401
FS: 0000000000000000(0000) GS:ffff88822bf40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f42ba70f030 CR3: 0000000109926000 CR4: 00000000000006e0
Call Trace:
br_handle_vlan+0xbc/0xca [bridge]
__br_forward+0x23/0x164 [bridge]
deliver_clone+0x41/0x48 [bridge]
br_handle_frame_finish+0x36f/0x3aa [bridge]
? skb_dst+0x2e/0x38 [bridge]
? br_handle_ingress_vlan_tunnel+0x3e/0x1c8 [bridge]
? br_handle_frame_finish+0x3aa/0x3aa [bridge]
br_handle_frame+0x2c3/0x377 [bridge]
? __skb_pull+0x33/0x51
? vlan_do_receive+0x4f/0x36a
? br_handle_frame_finish+0x3aa/0x3aa [bridge]
__netif_receive_skb_core+0x539/0x7c6
? __list_del_entry_valid+0x16e/0x1c2
__netif_receive_skb_list_core+0x6d/0xd6
netif_receive_skb_list_internal+0x1d9/0x1fa
gro_normal_list+0x22/0x3e
dev_gro_receive+0x55b/0x600
? detach_buf_split+0x58/0x140
napi_gro_receive+0x94/0x12e
virtnet_poll+0x15d/0x315 [virtio_net]
__napi_poll+0x2c/0x1c9
net_rx_action+0xe6/0x1fb
__do_softirq+0x115/0x2d8
run_ksoftirqd+0x18/0x20
smpboot_thread_fn+0x183/0x19c
? smpboot_unregister_percpu_thread+0x66/0x66
kthread+0x10a/0x10f
? kthread_mod_delayed_work+0xb6/0xb6
ret_from_fork+0x22/0x30
---[ end trace 49f61b07f775fd2b ]---
dst_release: dst:00000000c02d677a refcnt:-1
dst_release underflow
Cc: stable@vger.kernel.org
Fixes: 11538d039ac6 ("bridge: vlan dst_metadata hooks in ingress and egress paths")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58e2071742e38f29f051b709a5cca014ba51166f upstream.
This patch fixes a tunnel_dst null pointer dereference due to lockless
access in the tunnel egress path. When deleting a vlan tunnel the
tunnel_dst pointer is set to NULL without waiting a grace period (i.e.
while it's still usable) and packets egressing are dereferencing it
without checking. Use READ/WRITE_ONCE to annotate the lockless use of
tunnel_id, use RCU for accessing tunnel_dst and make sure it is read
only once and checked in the egress path. The dst is already properly RCU
protected so we don't need to do anything fancy than to make sure
tunnel_id and tunnel_dst are read only once and checked in the egress path.
Cc: stable@vger.kernel.org
Fixes: 11538d039ac6 ("bridge: vlan dst_metadata hooks in ingress and egress paths")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c364df2489b8ef2f5e3159b1dff1ff1fdb16040d upstream.
Just as the initial check, we need to ensure num_frag+1 buffers available,
as that is the number of buffers we are going to use.
This fixes a buffer overflow, which might be seen during heavy network
load. Complete lockup of TEMAC was reproducible within about 10 minutes of
a particular load.
Fixes: 84823ff80f74 ("net: ll_temac: Fix race condition causing TX hang")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6aa32217a9a446275440ee8724b1ecaf1838df47 upstream.
With the skb pointer piggy-backed on the TX BD, we have a simple and
efficient way to free the skb buffer when the frame has been transmitted.
But in order to avoid freeing the skb while there are still fragments from
the skb in use, we need to piggy-back on the TX BD of the skb, not the
first.
Without this, we are doing use-after-free on the DMA side, when the first
BD of a multi TX BD packet is seen as completed in xmit_done, and the
remaining BDs are still being processed.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4cbbe34807938e6e494e535a68d5ff64edac3f20 upstream.
If GC has entered CGPG, ringing doorbell > first page doesn't wakeup GC.
Enlarge CP_MEC_DOORBELL_RANGE_UPPER to workaround this issue.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c0b0efd148d5b24c4932ddb3fa03c8edd6097b3 upstream.
If GC has entered CGPG, ringing doorbell > first page doesn't wakeup GC.
Enlarge CP_MEC_DOORBELL_RANGE_UPPER to workaround this issue.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0288e5e16a2e18f0b7e61a2b70d9037fc6e4abeb upstream.
If cfg80211_pmsr_process_abort() moves all the PMSR requests that
need to be freed into a local list before aborting and freeing them.
As a result, it is possible that cfg80211_pmsr_complete() will run in
parallel and free the same PMSR request.
Fix it by freeing the request in cfg80211_pmsr_complete() only if it
is still in the original pmsr list.
Cc: stable@vger.kernel.org
Fixes: 9bb7e0f24e7e ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.1fbef57e269a.I00294bebdb0680b892f8d1d5c871fd9dbe785a5e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5642479b0f7168fe16d156913533fe65ab4f8d5 upstream.
If all net/wireless/certs/*.hex files are deleted, the build
will hang at this point since the 'cat' command will have no
arguments. Do "echo | cat - ..." so that even if the "..."
part is empty, the whole thing won't hang.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.c989056c3664.Ic3b77531d00b30b26dcd69c64e55ae2f60c3f31e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bddc0c411a45d3718ac535a070f349be8eca8d48 upstream.
The commit cb17ed29a7a5 ("mac80211: parse radiotap header when selecting Tx
queue") moved the code to validate the radiotap header from
ieee80211_monitor_start_xmit to ieee80211_parse_tx_radiotap. This made is
possible to share more code with the new Tx queue selection code for
injected frames. But at the same time, it now required the call of
ieee80211_parse_tx_radiotap at the beginning of functions which wanted to
handle the radiotap header. And this broke the rate parser for radiotap
header parser.
The radiotap parser for rates is operating most of the time only on the
data in the actual radiotap header. But for the 802.11a/b/g rates, it must
also know the selected band from the chandef information. But this
information is only written to the ieee80211_tx_info at the end of the
ieee80211_monitor_start_xmit - long after ieee80211_parse_tx_radiotap was
already called. The info->band information was therefore always 0
(NL80211_BAND_2GHZ) when the parser code tried to access it.
For a 5GHz only device, injecting a frame with 802.11a rates would cause a
NULL pointer dereference because local->hw.wiphy->bands[NL80211_BAND_2GHZ]
would most likely have been NULL when the radiotap parser searched for the
correct rate index of the driver.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: cb17ed29a7a5 ("mac80211: parse radiotap header when selecting Tx queue")
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
[sven@narfation.org: added commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20210530133226.40587-1-sven@narfation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4ad5dd2d7876d79507a20f026507d1a93b8fff10 upstream.
flags varible which is the input parameter of pl330_prep_dma_cyclic()
should not be used by spinlock_irq[save/restore] function.
Signed-off-by: Jongho Park <jongho7.park@samsung.com>
Signed-off-by: Bumyong Lee <bumyong.lee@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20210507063647.111209-1-chanho61.park@samsung.com
Fixes: f6f2421c0a1c ("dmaengine: pl330: Merge dma_pl330_dmac and pl330_dmac structs")
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f5aecdff25f59fb5ea456d5152a913906ecf287 upstream.
As mentioned in kernel commit 1d50e5d0c505 ("crash_core, vmcoreinfo:
Append 'MAX_PHYSMEM_BITS' to vmcoreinfo"), SECTION_SIZE_BITS in the
formula:
#define SECTIONS_SHIFT (MAX_PHYSMEM_BITS - SECTION_SIZE_BITS)
Besides SECTIONS_SHIFT, SECTION_SIZE_BITS is also used to calculate
PAGES_PER_SECTION in makedumpfile just like kernel.
Unfortunately, this arch-dependent macro SECTION_SIZE_BITS changes, e.g.
recently in kernel commit f0b13ee23241 ("arm64/sparsemem: reduce
SECTION_SIZE_BITS"). But user space wants a stable interface to get
this info. Such info is impossible to be deduced from a crashdump
vmcore. Hence append SECTION_SIZE_BITS to vmcoreinfo.
Link: https://lkml.kernel.org/r/20210608103359.84907-1-kernelfans@gmail.com
Link: http://lists.infradead.org/pipermail/kexec/2021-June/022676.html
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Cc: Kazuhito Hagio <k-hagio@ab.jp.nec.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Boris Petkov <bp@alien8.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Anderson <anderson@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit efa165504943f2128d50f63de0c02faf6dcceb0d upstream.
If access_ok() or fpregs_soft_set() fails in __fpu__restore_sig() then the
function just returns but does not clear the FPU state as it does for all
other fatal failures.
Clear the FPU state for these failures as well.
Fixes: 72a671ced66d ("x86, fpu: Unify signal handling code paths for x86 and x86_64 kernels")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/87mtryyhhz.ffs@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d8778e393afa421f1f117471144f8ce6deb6953a upstream.
Both Intel and AMD consider it to be architecturally valid for XRSTOR to
fail with #PF but nonetheless change the register state. The actual
conditions under which this might occur are unclear [1], but it seems
plausible that this might be triggered if one sibling thread unmaps a page
and invalidates the shared TLB while another sibling thread is executing
XRSTOR on the page in question.
__fpu__restore_sig() can execute XRSTOR while the hardware registers
are preserved on behalf of a different victim task (using the
fpu_fpregs_owner_ctx mechanism), and, in theory, XRSTOR could fail but
modify the registers.
If this happens, then there is a window in which __fpu__restore_sig()
could schedule out and the victim task could schedule back in without
reloading its own FPU registers. This would result in part of the FPU
state that __fpu__restore_sig() was attempting to load leaking into the
victim task's user-visible state.
Invalidate preserved FPU registers on XRSTOR failure to prevent this
situation from corrupting any state.
[1] Frequent readers of the errata lists might imagine "complex
microarchitectural conditions".
Fixes: 1d731e731c4c ("x86/fpu: Add a fastpath to __fpu__restore_sig()")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Rik van Riel <riel@surriel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210608144345.758116583@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 484cea4f362e1eeb5c869abbfb5f90eae6421b38 upstream.
The non-compacted slowpath uses __copy_from_user() and copies the entire
user buffer into the kernel buffer, verbatim. This means that the kernel
buffer may now contain entirely invalid state on which XRSTOR will #GP.
validate_user_xstate_header() can detect some of that corruption, but that
leaves the onus on callers to clear the buffer.
Prior to XSAVES support, it was possible just to reinitialize the buffer,
completely, but with supervisor states that is not longer possible as the
buffer clearing code split got it backwards. Fixing that is possible but
not corrupting the state in the first place is more robust.
Avoid corruption of the kernel XSAVE buffer by using copy_user_to_xstate()
which validates the XSAVE header contents before copying the actual states
to the kernel. copy_user_to_xstate() was previously only called for
compacted-format kernel buffers, but it works for both compacted and
non-compacted forms.
Using it for the non-compacted form is slower because of multiple
__copy_from_user() operations, but that cost is less important than robust
code in an already slow path.
[ Changelog polished by Dave Hansen ]
Fixes: b860eb8dce59 ("x86/fpu/xstate: Define new functions for clearing fpregs and xstates")
Reported-by: syzbot+2067e764dbcd10721e2e@syzkaller.appspotmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Rik van Riel <riel@surriel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210608144345.611833074@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 510b80a6a0f1a0d114c6e33bcea64747d127973c upstream.
When user space brings PKRU into init state, then the kernel handling is
broken:
T1 user space
xsave(state)
state.header.xfeatures &= ~XFEATURE_MASK_PKRU;
xrstor(state)
T1 -> kernel
schedule()
XSAVE(S) -> T1->xsave.header.xfeatures[PKRU] == 0
T1->flags |= TIF_NEED_FPU_LOAD;
wrpkru();
schedule()
...
pk = get_xsave_addr(&T1->fpu->state.xsave, XFEATURE_PKRU);
if (pk)
wrpkru(pk->pkru);
else
wrpkru(DEFAULT_PKRU);
Because the xfeatures bit is 0 and therefore the value in the xsave
storage is not valid, get_xsave_addr() returns NULL and switch_to()
writes the default PKRU. -> FAIL #1!
So that wrecks any copy_to/from_user() on the way back to user space
which hits memory which is protected by the default PKRU value.
Assumed that this does not fail (pure luck) then T1 goes back to user
space and because TIF_NEED_FPU_LOAD is set it ends up in
switch_fpu_return()
__fpregs_load_activate()
if (!fpregs_state_valid()) {
load_XSTATE_from_task();
}
But if nothing touched the FPU between T1 scheduling out and back in,
then the fpregs_state is still valid which means switch_fpu_return()
does nothing and just clears TIF_NEED_FPU_LOAD. Back to user space with
DEFAULT_PKRU loaded. -> FAIL #2!
The fix is simple: if get_xsave_addr() returns NULL then set the
PKRU value to 0 instead of the restrictive default PKRU value in
init_pkru_value.
[ bp: Massage in minor nitpicks from folks. ]
Fixes: 0cecca9d03c9 ("x86/fpu: Eager switch PKRU state")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Rik van Riel <riel@surriel.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210608144346.045616965@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d651ee9c71bb12fc0c8eb2786b66cbe5aa3e43b upstream.
Some drivers require memory that is marked as EFI boot services
data. In order for this memory to not be re-used by the kernel
after ExitBootServices(), efi_mem_reserve() is used to preserve it
by inserting a new EFI memory descriptor and marking it with the
EFI_MEMORY_RUNTIME attribute.
Under SEV, memory marked with the EFI_MEMORY_RUNTIME attribute needs to
be mapped encrypted by Linux, otherwise the kernel might crash at boot
like below:
EFI Variables Facility v0.08 2004-May-17
general protection fault, probably for non-canonical address 0x3597688770a868b2: 0000 [#1] SMP NOPTI
CPU: 13 PID: 1 Comm: swapper/0 Not tainted 5.12.4-2-default #1 openSUSE Tumbleweed
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:efi_mokvar_entry_next
[...]
Call Trace:
efi_mokvar_sysfs_init
? efi_mokvar_table_init
do_one_initcall
? __kmalloc
kernel_init_freeable
? rest_init
kernel_init
ret_from_fork
Expand the __ioremap_check_other() function to additionally check for
this other type of boot data reserved at runtime and indicate that it
should be mapped encrypted for an SEV guest.
[ bp: Massage commit message. ]
Fixes: 58c909022a5a ("efi: Support for MOK variable config table")
Reported-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Joerg Roedel <jroedel@suse.de>
Cc: <stable@vger.kernel.org> # 5.10+
Link: https://lkml.kernel.org/r/20210608095439.12668-2-joro@8bytes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 12f7764ac61200e32c916f038bdc08f884b0b604 upstream.
switch_fpu_finish() checks current->mm as indicator for kernel threads.
That's wrong because kernel threads can temporarily use a mm of a user
process via kthread_use_mm().
Check the task flags for PF_KTHREAD instead.
Fixes: 0cecca9d03c9 ("x86/fpu: Eager switch PKRU state")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Rik van Riel <riel@surriel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210608144345.912645927@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28e5e44aa3f4e0e0370864ed008fb5e2d85f4dc8 upstream.
tl;dr:
Several SGX users reported seeing the following message on NUMA systems:
sgx: [Firmware Bug]: Unable to map EPC section to online node. Fallback to the NUMA node 0.
This turned out to be the memblock code mistakenly throwing away SGX
memory.
=== Full Changelog ===
The 'max_pfn' variable represents the highest known RAM address. It can
be used, for instance, to quickly determine for which physical addresses
there is mem_map[] space allocated. The numa_meminfo code makes an
effort to throw out ("trim") all memory blocks which are above 'max_pfn'.
SGX memory is not considered RAM (it is marked as "Reserved" in the
e820) and is not taken into account by max_pfn. Despite this, SGX memory
areas have NUMA affinity and are enumerated in the ACPI SRAT table. The
existing SGX code uses the numa_meminfo mechanism to look up the NUMA
affinity for its memory areas.
In cases where SGX memory was above max_pfn (usually just the one EPC
section in the last highest NUMA node), the numa_memblock is truncated
at 'max_pfn', which is below the SGX memory. When the SGX code tries to
look up the affinity of this memory, it fails and produces an error message:
sgx: [Firmware Bug]: Unable to map EPC section to online node. Fallback to the NUMA node 0.
and assigns the memory to NUMA node 0.
Instead of silently truncating the memory block at 'max_pfn' and
dropping the SGX memory, add the truncated portion to
'numa_reserved_meminfo'. This allows the SGX code to later determine
the NUMA affinity of its 'Reserved' area.
Before, numa_meminfo looked like this (from 'crash'):
blk = { start = 0x0, end = 0x2080000000, nid = 0x0 }
{ start = 0x2080000000, end = 0x4000000000, nid = 0x1 }
numa_reserved_meminfo is empty.
With this, numa_meminfo looks like this:
blk = { start = 0x0, end = 0x2080000000, nid = 0x0 }
{ start = 0x2080000000, end = 0x4000000000, nid = 0x1 }
and numa_reserved_meminfo has an entry for node 1's SGX memory:
blk = { start = 0x4000000000, end = 0x4080000000, nid = 0x1 }
[ daveh: completely rewrote/reworked changelog ]
Fixes: 5d30f92e7631 ("x86/NUMA: Provide a range-to-target_node lookup facility")
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20210617194657.0A99CB22@viggo.jf.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96f1b00138cb8f04c742c82d0a7c460b2202e887 upstream.
ARCv2 has some configuration dependent registers (r30, r58, r59) which
could be targetted by the compiler. To keep the ABI stable, these were
unconditionally part of the glibc ABI
(sysdeps/unix/sysv/linux/arc/sys/ucontext.h:mcontext_t) however we
missed populating them (by saving/restoring them across signal
handling).
This patch fixes the issue by
- adding arcv2 ABI regs to kernel struct sigcontext
- populating them during signal handling
Change to struct sigcontext might seem like a glibc ABI change (although
it primarily uses ucontext_t:mcontext_t) but the fact is
- it has only been extended (existing fields are not touched)
- the old sigcontext was ABI incomplete to begin with anyways
Fixes: https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/53
Cc: <stable@vger.kernel.org>
Tested-by: kernel test robot <lkp@intel.com>
Reported-by: Vladimir Isaev <isaev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e73a99f3287a740a07d6618e9470f4d6cb217da8 upstream.
When a AP queue is switched to soft offline, all pending
requests are purged out of the pending requests list and
'received' by the upper layer like zcrypt device drivers.
This is also done for requests which are already enqueued
into the firmware queue. A request in a firmware queue
may eventually produce an response message, but there is
no waiting process any more. However, the response was
counted with the queue_counter and as this counter was
reset to 0 with the offline switch, the pending response
caused the queue_counter to get negative. The next request
increased this counter to 0 (instead of 1) which caused
the ap code to assume there is nothing to receive and so
the response for this valid request was never tried to
fetch from the firmware queue.
This all caused a queue to not work properly after a
switch offline/online and in the end processes to hang
forever when trying to send a crypto request after an
queue offline/online switch cicle.
Fixed by a) making sure the counter does not drop below 0
and b) on a successful enqueue of a message has at least
a value of 1.
Additionally a warning is emitted, when a reply can't get
assigned to a waiting process. This may be normal operation
(process had timeout or has been killed) but may give a
hint that something unexpected happened (like this odd
behavior described above).
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5bcbe3285fb614c49db6b238253f7daff7e66312 upstream.
The size of SIE critical section is calculated wrongly
as result of a missed subtraction in commit 0b0ed657fe00
("s390: remove critical section cleanup from entry.S")
Fixes: 0b0ed657fe00 ("s390: remove critical section cleanup from entry.S")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dfdc0a714d241bfbf951886c373cd1ae463fcc25 upstream.
Commit c9b8b07cded58 (KVM: x86: Dynamically allocate per-vCPU emulation context)
tries to allocate per-vCPU emulation context dynamically, however, the
x86_emulator slab cache is still exiting after the kvm module is unload
as below after destroying the VM and unloading the kvm module.
grep x86_emulator /proc/slabinfo
x86_emulator 36 36 2672 12 8 : tunables 0 0 0 : slabdata 3 3 0
This patch fixes this slab cache leak by destroying the x86_emulator slab cache
when the kvm module is unloaded.
Fixes: c9b8b07cded58 (KVM: x86: Dynamically allocate per-vCPU emulation context)
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1623387573-5969-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 654430efde27248be563df9a88631204b5fe2df2 upstream.
Calculate and check the full mmu_role when initializing the MMU context
for the nested MMU, where "full" means the bits and pieces of the role
that aren't handled by kvm_calc_mmu_role_common(). While the nested MMU
isn't used for shadow paging, things like the number of levels in the
guest's page tables are surprisingly important when walking the guest
page tables. Failure to reinitialize the nested MMU context if L2's
paging mode changes can result in unexpected and/or missed page faults,
and likely other explosions.
E.g. if an L1 vCPU is running both a 32-bit PAE L2 and a 64-bit L2, the
"common" role calculation will yield the same role for both L2s. If the
64-bit L2 is run after the 32-bit PAE L2, L0 will fail to reinitialize
the nested MMU context, ultimately resulting in a bad walk of L2's page
tables as the MMU will still have a guest root_level of PT32E_ROOT_LEVEL.
WARNING: CPU: 4 PID: 167334 at arch/x86/kvm/vmx/vmx.c:3075 ept_save_pdptrs+0x15/0xe0 [kvm_intel]
Modules linked in: kvm_intel]
CPU: 4 PID: 167334 Comm: CPU 3/KVM Not tainted 5.13.0-rc1-d849817d5673-reqs #185
Hardware name: ASUS Q87M-E/Q87M-E, BIOS 1102 03/03/2014
RIP: 0010:ept_save_pdptrs+0x15/0xe0 [kvm_intel]
Code: <0f> 0b c3 f6 87 d8 02 00f
RSP: 0018:ffffbba702dbba00 EFLAGS: 00010202
RAX: 0000000000000011 RBX: 0000000000000002 RCX: ffffffff810a2c08
RDX: ffff91d7bc30acc0 RSI: 0000000000000011 RDI: ffff91d7bc30a600
RBP: ffff91d7bc30a600 R08: 0000000000000010 R09: 0000000000000007
R10: 0000000000000000 R11: 0000000000000000 R12: ffff91d7bc30a600
R13: ffff91d7bc30acc0 R14: ffff91d67c123460 R15: 0000000115d7e005
FS: 00007fe8e9ffb700(0000) GS:ffff91d90fb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000029f15a001 CR4: 00000000001726e0
Call Trace:
kvm_pdptr_read+0x3a/0x40 [kvm]
paging64_walk_addr_generic+0x327/0x6a0 [kvm]
paging64_gva_to_gpa_nested+0x3f/0xb0 [kvm]
kvm_fetch_guest_virt+0x4c/0xb0 [kvm]
__do_insn_fetch_bytes+0x11a/0x1f0 [kvm]
x86_decode_insn+0x787/0x1490 [kvm]
x86_decode_emulated_instruction+0x58/0x1e0 [kvm]
x86_emulate_instruction+0x122/0x4f0 [kvm]
vmx_handle_exit+0x120/0x660 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0xe25/0x1cb0 [kvm]
kvm_vcpu_ioctl+0x211/0x5a0 [kvm]
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x40/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Fixes: bf627a928837 ("x86/kvm/mmu: check if MMU reconfiguration is needed in init_kvm_nested_mmu()")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210610220026.1364486-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
