diff options
Diffstat (limited to 'drivers/fpga')
| -rw-r--r-- | drivers/fpga/Kconfig | 11 | ||||
| -rw-r--r-- | drivers/fpga/Makefile | 2 | ||||
| -rw-r--r-- | drivers/fpga/dfl-n3000-nios.c | 588 | ||||
| -rw-r--r-- | drivers/fpga/dfl-pci.c | 165 | ||||
| -rw-r--r-- | drivers/fpga/dfl.c | 4 | ||||
| -rw-r--r-- | drivers/fpga/dfl.h | 85 |
6 files changed, 734 insertions, 121 deletions
diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig index 5645226ca3ce..5ff9438b7b46 100644 --- a/drivers/fpga/Kconfig +++ b/drivers/fpga/Kconfig @@ -192,6 +192,17 @@ config FPGA_DFL_AFU to the FPGA infrastructure via a Port. There may be more than one Port/AFU per DFL based FPGA device. +config FPGA_DFL_NIOS_INTEL_PAC_N3000 + tristate "FPGA DFL NIOS Driver for Intel PAC N3000" + depends on FPGA_DFL + select REGMAP + help + This is the driver for the N3000 Nios private feature on Intel + PAC (Programmable Acceleration Card) N3000. It communicates + with the embedded Nios processor to configure the retimers on + the card. It also instantiates the SPI master (spi-altera) for + the card's BMC (Board Management Controller). + config FPGA_DFL_PCI tristate "FPGA DFL PCIe Device Driver" depends on PCI && FPGA_DFL diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index d8e21dfc6778..18dc9885883a 100644 --- a/drivers/fpga/Makefile +++ b/drivers/fpga/Makefile @@ -44,5 +44,7 @@ dfl-fme-objs += dfl-fme-perf.o dfl-afu-objs := dfl-afu-main.o dfl-afu-region.o dfl-afu-dma-region.o dfl-afu-objs += dfl-afu-error.o +obj-$(CONFIG_FPGA_DFL_NIOS_INTEL_PAC_N3000) += dfl-n3000-nios.o + # Drivers for FPGAs which implement DFL obj-$(CONFIG_FPGA_DFL_PCI) += dfl-pci.o diff --git a/drivers/fpga/dfl-n3000-nios.c b/drivers/fpga/dfl-n3000-nios.c new file mode 100644 index 000000000000..7a95366f6516 --- /dev/null +++ b/drivers/fpga/dfl-n3000-nios.c @@ -0,0 +1,588 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * DFL device driver for Nios private feature on Intel PAC (Programmable + * Acceleration Card) N3000 + * + * Copyright (C) 2019-2020 Intel Corporation, Inc. + * + * Authors: + * Wu Hao <hao.wu@intel.com> + * Xu Yilun <yilun.xu@intel.com> + */ +#include <linux/bitfield.h> +#include <linux/dfl.h> +#include <linux/errno.h> +#include <linux/io.h> +#include <linux/io-64-nonatomic-lo-hi.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/stddef.h> +#include <linux/spi/altera.h> +#include <linux/spi/spi.h> +#include <linux/types.h> + +/* + * N3000 Nios private feature registers, named as NIOS_SPI_XX on spec. + * NS is the abbreviation of NIOS_SPI. + */ +#define N3000_NS_PARAM 0x8 +#define N3000_NS_PARAM_SHIFT_MODE_MSK BIT_ULL(1) +#define N3000_NS_PARAM_SHIFT_MODE_MSB 0 +#define N3000_NS_PARAM_SHIFT_MODE_LSB 1 +#define N3000_NS_PARAM_DATA_WIDTH GENMASK_ULL(7, 2) +#define N3000_NS_PARAM_NUM_CS GENMASK_ULL(13, 8) +#define N3000_NS_PARAM_CLK_POL BIT_ULL(14) +#define N3000_NS_PARAM_CLK_PHASE BIT_ULL(15) +#define N3000_NS_PARAM_PERIPHERAL_ID GENMASK_ULL(47, 32) + +#define N3000_NS_CTRL 0x10 +#define N3000_NS_CTRL_WR_DATA GENMASK_ULL(31, 0) +#define N3000_NS_CTRL_ADDR GENMASK_ULL(44, 32) +#define N3000_NS_CTRL_CMD_MSK GENMASK_ULL(63, 62) +#define N3000_NS_CTRL_CMD_NOP 0 +#define N3000_NS_CTRL_CMD_RD 1 +#define N3000_NS_CTRL_CMD_WR 2 + +#define N3000_NS_STAT 0x18 +#define N3000_NS_STAT_RD_DATA GENMASK_ULL(31, 0) +#define N3000_NS_STAT_RW_VAL BIT_ULL(32) + +/* Nios handshake registers, indirect access */ +#define N3000_NIOS_INIT 0x1000 +#define N3000_NIOS_INIT_DONE BIT(0) +#define N3000_NIOS_INIT_START BIT(1) +/* Mode for retimer A, link 0, the same below */ +#define N3000_NIOS_INIT_REQ_FEC_MODE_A0_MSK GENMASK(9, 8) +#define N3000_NIOS_INIT_REQ_FEC_MODE_A1_MSK GENMASK(11, 10) +#define N3000_NIOS_INIT_REQ_FEC_MODE_A2_MSK GENMASK(13, 12) +#define N3000_NIOS_INIT_REQ_FEC_MODE_A3_MSK GENMASK(15, 14) +#define N3000_NIOS_INIT_REQ_FEC_MODE_B0_MSK GENMASK(17, 16) +#define N3000_NIOS_INIT_REQ_FEC_MODE_B1_MSK GENMASK(19, 18) +#define N3000_NIOS_INIT_REQ_FEC_MODE_B2_MSK GENMASK(21, 20) +#define N3000_NIOS_INIT_REQ_FEC_MODE_B3_MSK GENMASK(23, 22) +#define N3000_NIOS_INIT_REQ_FEC_MODE_NO 0x0 +#define N3000_NIOS_INIT_REQ_FEC_MODE_KR 0x1 +#define N3000_NIOS_INIT_REQ_FEC_MODE_RS 0x2 + +#define N3000_NIOS_FW_VERSION 0x1004 +#define N3000_NIOS_FW_VERSION_PATCH GENMASK(23, 20) +#define N3000_NIOS_FW_VERSION_MINOR GENMASK(27, 24) +#define N3000_NIOS_FW_VERSION_MAJOR GENMASK(31, 28) + +/* The retimers we use on Intel PAC N3000 is Parkvale, abbreviated to PKVL */ +#define N3000_NIOS_PKVL_A_MODE_STS 0x1020 +#define N3000_NIOS_PKVL_B_MODE_STS 0x1024 +#define N3000_NIOS_PKVL_MODE_STS_GROUP_MSK GENMASK(15, 8) +#define N3000_NIOS_PKVL_MODE_STS_GROUP_OK 0x0 +#define N3000_NIOS_PKVL_MODE_STS_ID_MSK GENMASK(7, 0) +/* When GROUP MASK field == GROUP_OK */ +#define N3000_NIOS_PKVL_MODE_ID_RESET 0x0 +#define N3000_NIOS_PKVL_MODE_ID_4X10G 0x1 +#define N3000_NIOS_PKVL_MODE_ID_4X25G 0x2 +#define N3000_NIOS_PKVL_MODE_ID_2X25G 0x3 +#define N3000_NIOS_PKVL_MODE_ID_2X25G_2X10G 0x4 +#define N3000_NIOS_PKVL_MODE_ID_1X25G 0x5 + +#define N3000_NIOS_REGBUS_RETRY_COUNT 10000 /* loop count */ + +#define N3000_NIOS_INIT_TIMEOUT 10000000 /* usec */ +#define N3000_NIOS_INIT_TIME_INTV 100000 /* usec */ + +#define N3000_NIOS_INIT_REQ_FEC_MODE_MSK_ALL \ + (N3000_NIOS_INIT_REQ_FEC_MODE_A0_MSK | \ + N3000_NIOS_INIT_REQ_FEC_MODE_A1_MSK | \ + N3000_NIOS_INIT_REQ_FEC_MODE_A2_MSK | \ + N3000_NIOS_INIT_REQ_FEC_MODE_A3_MSK | \ + N3000_NIOS_INIT_REQ_FEC_MODE_B0_MSK | \ + N3000_NIOS_INIT_REQ_FEC_MODE_B1_MSK | \ + N3000_NIOS_INIT_REQ_FEC_MODE_B2_MSK | \ + N3000_NIOS_INIT_REQ_FEC_MODE_B3_MSK) + +#define N3000_NIOS_INIT_REQ_FEC_MODE_NO_ALL \ + (FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A0_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A1_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A2_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A3_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B0_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B1_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B2_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B3_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_NO)) + +#define N3000_NIOS_INIT_REQ_FEC_MODE_KR_ALL \ + (FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A0_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A1_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A2_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A3_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B0_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B1_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B2_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B3_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_KR)) + +#define N3000_NIOS_INIT_REQ_FEC_MODE_RS_ALL \ + (FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A0_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A1_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A2_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A3_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B0_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B1_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B2_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \ + FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B3_MSK, \ + N3000_NIOS_INIT_REQ_FEC_MODE_RS)) + +struct n3000_nios { + void __iomem *base; + struct regmap *regmap; + struct device *dev; + struct platform_device *altera_spi; +}; + +static ssize_t nios_fw_version_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct n3000_nios *nn = dev_get_drvdata(dev); + unsigned int val; + int ret; + + ret = regmap_read(nn->regmap, N3000_NIOS_FW_VERSION, &val); + if (ret) + return ret; + + return sysfs_emit(buf, "%x.%x.%x\n", + (u8)FIELD_GET(N3000_NIOS_FW_VERSION_MAJOR, val), + (u8)FIELD_GET(N3000_NIOS_FW_VERSION_MINOR, val), + (u8)FIELD_GET(N3000_NIOS_FW_VERSION_PATCH, val)); +} +static DEVICE_ATTR_RO(nios_fw_version); + +#define IS_MODE_STATUS_OK(mode_stat) \ + (FIELD_GET(N3000_NIOS_PKVL_MODE_STS_GROUP_MSK, (mode_stat)) == \ + N3000_NIOS_PKVL_MODE_STS_GROUP_OK) + +#define IS_RETIMER_FEC_SUPPORTED(retimer_mode) \ + ((retimer_mode) != N3000_NIOS_PKVL_MODE_ID_RESET && \ + (retimer_mode) != N3000_NIOS_PKVL_MODE_ID_4X10G) + +static int get_retimer_mode(struct n3000_nios *nn, unsigned int mode_stat_reg, + unsigned int *retimer_mode) +{ + unsigned int val; + int ret; + + ret = regmap_read(nn->regmap, mode_stat_reg, &val); + if (ret) + return ret; + + if (!IS_MODE_STATUS_OK(val)) + return -EFAULT; + + *retimer_mode = FIELD_GET(N3000_NIOS_PKVL_MODE_STS_ID_MSK, val); + + return 0; +} + +static ssize_t retimer_A_mode_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct n3000_nios *nn = dev_get_drvdata(dev); + unsigned int mode; + int ret; + + ret = get_retimer_mode(nn, N3000_NIOS_PKVL_A_MODE_STS, &mode); + if (ret) + return ret; + + return sysfs_emit(buf, "0x%x\n", mode); +} +static DEVICE_ATTR_RO(retimer_A_mode); + +static ssize_t retimer_B_mode_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct n3000_nios *nn = dev_get_drvdata(dev); + unsigned int mode; + int ret; + + ret = get_retimer_mode(nn, N3000_NIOS_PKVL_B_MODE_STS, &mode); + if (ret) + return ret; + + return sysfs_emit(buf, "0x%x\n", mode); +} +static DEVICE_ATTR_RO(retimer_B_mode); + +static ssize_t fec_mode_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + unsigned int val, retimer_a_mode, retimer_b_mode, fec_modes; + struct n3000_nios *nn = dev_get_drvdata(dev); + int ret; + + /* FEC mode setting is not supported in early FW versions */ + ret = regmap_read(nn->regmap, N3000_NIOS_FW_VERSION, &val); + if (ret) + return ret; + + if (FIELD_GET(N3000_NIOS_FW_VERSION_MAJOR, val) < 3) + return sysfs_emit(buf, "not supported\n"); + + /* If no 25G links, FEC mode setting is not supported either */ + ret = get_retimer_mode(nn, N3000_NIOS_PKVL_A_MODE_STS, &retimer_a_mode); + if (ret) + return ret; + + ret = get_retimer_mode(nn, N3000_NIOS_PKVL_B_MODE_STS, &retimer_b_mode); + if (ret) + return ret; + + if (!IS_RETIMER_FEC_SUPPORTED(retimer_a_mode) && + !IS_RETIMER_FEC_SUPPORTED(retimer_b_mode)) + return sysfs_emit(buf, "not supported\n"); + + /* get the valid FEC mode for 25G links */ + ret = regmap_read(nn->regmap, N3000_NIOS_INIT, &val); + if (ret) + return ret; + + /* + * FEC mode should always be the same for all links, as we set them + * in this way. + */ + fec_modes = (val & N3000_NIOS_INIT_REQ_FEC_MODE_MSK_ALL); + if (fec_modes == N3000_NIOS_INIT_REQ_FEC_MODE_NO_ALL) + return sysfs_emit(buf, "no\n"); + else if (fec_modes == N3000_NIOS_INIT_REQ_FEC_MODE_KR_ALL) + return sysfs_emit(buf, "kr\n"); + else if (fec_modes == N3000_NIOS_INIT_REQ_FEC_MODE_RS_ALL) + return sysfs_emit(buf, "rs\n"); + + return -EFAULT; +} +static DEVICE_ATTR_RO(fec_mode); + +static struct attribute *n3000_nios_attrs[] = { + &dev_attr_nios_fw_version.attr, + &dev_attr_retimer_A_mode.attr, + &dev_attr_retimer_B_mode.attr, + &dev_attr_fec_mode.attr, + NULL, +}; +ATTRIBUTE_GROUPS(n3000_nios); + +static int n3000_nios_init_done_check(struct n3000_nios *nn) +{ + unsigned int val, state_a, state_b; + struct device *dev = nn->dev; + int ret, ret2; + + /* + * The SPI is shared by the Nios core inside the FPGA, Nios will use + * this SPI master to do some one time initialization after power up, + * and then release the control to OS. The driver needs to poll on + * INIT_DONE to see when driver could take the control. + * + * Please note that after Nios firmware version 3.0.0, INIT_START is + * introduced, so driver needs to trigger START firstly and then check + * INIT_DONE. + */ + + ret = regmap_read(nn->regmap, N3000_NIOS_FW_VERSION, &val); + if (ret) + return ret; + + /* + * If Nios version register is totally uninitialized(== 0x0), then the + * Nios firmware is missing. So host could take control of SPI master + * safely, but initialization work for Nios is not done. To restore the + * card, we need to reprogram a new Nios firmware via the BMC chip on + * SPI bus. So the driver doesn't error out, it continues to create the + * spi controller device and spi_board_info for BMC. + */ + if (val == 0) { + dev_err(dev, "Nios version reg = 0x%x, skip INIT_DONE check, but the retimer may be uninitialized\n", + val); + return 0; + } + + if (FIELD_GET(N3000_NIOS_FW_VERSION_MAJOR, val) >= 3) { + /* read NIOS_INIT to check if retimer initialization is done */ + ret = regmap_read(nn->regmap, N3000_NIOS_INIT, &val); + if (ret) + return ret; + + /* check if retimers are initialized already */ + if (val & (N3000_NIOS_INIT_DONE | N3000_NIOS_INIT_START)) + goto nios_init_done; + + /* configure FEC mode per module param */ + val = N3000_NIOS_INIT_START; + + /* + * When the retimer is to be set to 10G mode, there is no FEC + * mode setting, so the REQ_FEC_MODE field will be ignored by + * Nios firmware in this case. But we should still fill the FEC + * mode field cause host could not get the retimer working mode + * until the Nios init is done. + * + * For now the driver doesn't support the retimer FEC mode + * switching per user's request. It is always set to Reed + * Solomon FEC. + * + * The driver will set the same FEC mode for all links. + */ + val |= N3000_NIOS_INIT_REQ_FEC_MODE_RS_ALL; + + ret = regmap_write(nn->regmap, N3000_NIOS_INIT, val); + if (ret) + return ret; + } + +nios_init_done: + /* polls on NIOS_INIT_DONE */ + ret = regmap_read_poll_timeout(nn->regmap, N3000_NIOS_INIT, val, + val & N3000_NIOS_INIT_DONE, + N3000_NIOS_INIT_TIME_INTV, + N3000_NIOS_INIT_TIMEOUT); + if (ret) + dev_err(dev, "NIOS_INIT_DONE %s\n", + (ret == -ETIMEDOUT) ? "timed out" : "check error"); + + ret2 = regmap_read(nn->regmap, N3000_NIOS_PKVL_A_MODE_STS, &state_a); + if (ret2) + return ret2; + + ret2 = regmap_read(nn->regmap, N3000_NIOS_PKVL_B_MODE_STS, &state_b); + if (ret2) + return ret2; + + if (!ret) { + /* + * After INIT_DONE is detected, it still needs to check if the + * Nios firmware reports any error during the retimer + * configuration. + */ + if (IS_MODE_STATUS_OK(state_a) && IS_MODE_STATUS_OK(state_b)) + return 0; + + /* + * If the retimer configuration is failed, the Nios firmware + * will still release the spi controller for host to + * communicate with the BMC. It makes possible for people to + * reprogram a new Nios firmware and restore the card. So the + * driver doesn't error out, it continues to create the spi + * controller device and spi_board_info for BMC. + */ + dev_err(dev, "NIOS_INIT_DONE OK, but err on retimer init\n"); + } + + dev_err(nn->dev, "PKVL_A_MODE_STS 0x%x\n", state_a); + dev_err(nn->dev, "PKVL_B_MODE_STS 0x%x\n", state_b); + + return ret; +} + +static struct spi_board_info m10_n3000_info = { + .modalias = "m10-n3000", + .max_speed_hz = 12500000, + .bus_num = 0, + .chip_select = 0, +}; + +static int create_altera_spi_controller(struct n3000_nios *nn) +{ + struct altera_spi_platform_data pdata = { 0 }; + struct platform_device_info pdevinfo = { 0 }; + void __iomem *base = nn->base; + u64 v; + + v = readq(base + N3000_NS_PARAM); + + pdata.mode_bits = SPI_CS_HIGH; + if (FIELD_GET(N3000_NS_PARAM_CLK_POL, v)) + pdata.mode_bits |= SPI_CPOL; + if (FIELD_GET(N3000_NS_PARAM_CLK_PHASE, v)) + pdata.mode_bits |= SPI_CPHA; + + pdata.num_chipselect = FIELD_GET(N3000_NS_PARAM_NUM_CS, v); + pdata.bits_per_word_mask = + SPI_BPW_RANGE_MASK(1, FIELD_GET(N3000_NS_PARAM_DATA_WIDTH, v)); + + pdata.num_devices = 1; + pdata.devices = &m10_n3000_info; + + dev_dbg(nn->dev, "%s cs %u bpm 0x%x mode 0x%x\n", __func__, + pdata.num_chipselect, pdata.bits_per_word_mask, + pdata.mode_bits); + + pdevinfo.name = "subdev_spi_altera"; + pdevinfo.id = PLATFORM_DEVID_AUTO; + pdevinfo.parent = nn->dev; + pdevinfo.data = &pdata; + pdevinfo.size_data = sizeof(pdata); + + nn->altera_spi = platform_device_register_full(&pdevinfo); + return PTR_ERR_OR_ZERO(nn->altera_spi); +} + +static void destroy_altera_spi_controller(struct n3000_nios *nn) +{ + platform_device_unregister(nn->altera_spi); +} + +static int n3000_nios_poll_stat_timeout(void __iomem *base, u64 *v) +{ + int loops; + + /* + * We don't use the time based timeout here for performance. + * + * The regbus read/write is on the critical path of Intel PAC N3000 + * image programing. The time based timeout checking will add too much + * overhead on it. Usually the state changes in 1 or 2 loops on the + * test server, and we set 10000 times loop here for safety. + */ + for (loops = N3000_NIOS_REGBUS_RETRY_COUNT; loops > 0 ; loops--) { + *v = readq(base + N3000_NS_STAT); + if (*v & N3000_NS_STAT_RW_VAL) + break; + cpu_relax(); + } + + return (loops > 0) ? 0 : -ETIMEDOUT; +} + +static int n3000_nios_reg_write(void *context, unsigned int reg, unsigned int val) +{ + struct n3000_nios *nn = context; + u64 v; + int ret; + + v = FIELD_PREP(N3000_NS_CTRL_CMD_MSK, N3000_NS_CTRL_CMD_WR) | + FIELD_PREP(N3000_NS_CTRL_ADDR, reg) | + FIELD_PREP(N3000_NS_CTRL_WR_DATA, val); + writeq(v, nn->base + N3000_NS_CTRL); + + ret = n3000_nios_poll_stat_timeout(nn->base, &v); + if (ret) + dev_err(nn->dev, "fail to write reg 0x%x val 0x%x: %d\n", + reg, val, ret); + + return ret; +} + +static int n3000_nios_reg_read(void *context, unsigned int reg, unsigned int *val) +{ + struct n3000_nios *nn = context; + u64 v; + int ret; + + v = FIELD_PREP(N3000_NS_CTRL_CMD_MSK, N3000_NS_CTRL_CMD_RD) | + FIELD_PREP(N3000_NS_CTRL_ADDR, reg); + writeq(v, nn->base + N3000_NS_CTRL); + + ret = n3000_nios_poll_stat_timeout(nn->base, &v); + if (ret) + dev_err(nn->dev, "fail to read reg 0x%x: %d\n", reg, ret); + else + *val = FIELD_GET(N3000_NS_STAT_RD_DATA, v); + + return ret; +} + +static const struct regmap_config n3000_nios_regbus_cfg = { + .reg_bits = 32, + .reg_stride = 4, + .val_bits = 32, + .fast_io = true, + + .reg_write = n3000_nios_reg_write, + .reg_read = n3000_nios_reg_read, +}; + +static int n3000_nios_probe(struct dfl_device *ddev) +{ + struct device *dev = &ddev->dev; + struct n3000_nios *nn; + int ret; + + nn = devm_kzalloc(dev, sizeof(*nn), GFP_KERNEL); + if (!nn) + return -ENOMEM; + + dev_set_drvdata(&ddev->dev, nn); + + nn->dev = dev; + + nn->base = devm_ioremap_resource(&ddev->dev, &ddev->mmio_res); + if (IS_ERR(nn->base)) + return PTR_ERR(nn->base); + + nn->regmap = devm_regmap_init(dev, NULL, nn, &n3000_nios_regbus_cfg); + if (IS_ERR(nn->regmap)) + return PTR_ERR(nn->regmap); + + ret = n3000_nios_init_done_check(nn); + if (ret) + return ret; + + ret = create_altera_spi_controller(nn); + if (ret) + dev_err(dev, "altera spi controller create failed: %d\n", ret); + + return ret; +} + +static void n3000_nios_remove(struct dfl_device *ddev) +{ + struct n3000_nios *nn = dev_get_drvdata(&ddev->dev); + + destroy_altera_spi_controller(nn); +} + +#define FME_FEATURE_ID_N3000_NIOS 0xd + +static const struct dfl_device_id n3000_nios_ids[] = { + { FME_ID, FME_FEATURE_ID_N3000_NIOS }, + { } +}; +MODULE_DEVICE_TABLE(dfl, n3000_nios_ids); + +static struct dfl_driver n3000_nios_driver = { + .drv = { + .name = "dfl-n3000-nios", + .dev_groups = n3000_nios_groups, + }, + .id_table = n3000_nios_ids, + .probe = n3000_nios_probe, + .remove = n3000_nios_remove, +}; + +module_dfl_driver(n3000_nios_driver); + +MODULE_DESCRIPTION("Driver for Nios private feature on Intel PAC N3000"); +MODULE_AUTHOR("Intel Corporation"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/fpga/dfl-pci.c b/drivers/fpga/dfl-pci.c index a2203d03c9e2..04e47e266f26 100644 --- a/drivers/fpga/dfl-pci.c +++ b/drivers/fpga/dfl-pci.c @@ -27,6 +27,14 @@ #define DRV_VERSION "0.8" #define DRV_NAME "dfl-pci" +#define PCI_VSEC_ID_INTEL_DFLS 0x43 + +#define PCI_VNDR_DFLS_CNT 0x8 +#define PCI_VNDR_DFLS_RES 0xc + +#define PCI_VNDR_DFLS_RES_BAR_MASK GENMASK(2, 0) +#define PCI_VNDR_DFLS_RES_OFF_MASK GENMASK(31, 3) + struct cci_drvdata { struct dfl_fpga_cdev *cdev; /* container device */ }; @@ -119,49 +127,94 @@ static int *cci_pci_create_irq_table(struct pci_dev *pcidev, unsigned int nvec) return table; } -/* enumerate feature devices under pci device */ -static int cci_enumerate_feature_devs(struct pci_dev *pcidev) +static int find_dfls_by_vsec(struct pci_dev *pcidev, struct dfl_fpga_enum_info *info) { - struct cci_drvdata *drvdata = pci_get_drvdata(pcidev); - int port_num, bar, i, nvec, ret = 0; - struct dfl_fpga_enum_info *info; - struct dfl_fpga_cdev *cdev; + u32 bir, offset, vndr_hdr, dfl_cnt, dfl_res; + int dfl_res_off, i, bars, voff = 0; resource_size_t start, len; - void __iomem *base; - int *irq_table; - u32 offset; - u64 v; - /* allocate enumeration info via pci_dev */ - info = dfl_fpga_enum_info_alloc(&pcidev->dev); - if (!info) - return -ENOMEM; + while ((voff = pci_find_next_ext_capability(pcidev, voff, PCI_EXT_CAP_ID_VNDR))) { + vndr_hdr = 0; + pci_read_config_dword(pcidev, voff + PCI_VNDR_HEADER, &vndr_hdr); - /* add irq info for enumeration if the device support irq */ - nvec = cci_pci_alloc_irq(pcidev); - if (nvec < 0) { - dev_err(&pcidev->dev, "Fail to alloc irq %d.\n", nvec); - ret = nvec; - goto enum_info_free_exit; - } else if (nvec) { - irq_table = cci_pci_create_irq_table(pcidev, nvec); - if (!irq_table) { - ret = -ENOMEM; - goto irq_free_exit; + if (PCI_VNDR_HEADER_ID(vndr_hdr) == PCI_VSEC_ID_INTEL_DFLS && + pcidev->vendor == PCI_VENDOR_ID_INTEL) + break; + } + + if (!voff) { + dev_dbg(&pcidev->dev, "%s no DFL VSEC found\n", __func__); + return -ENODEV; + } + + dfl_cnt = 0; + pci_read_config_dword(pcidev, voff + PCI_VNDR_DFLS_CNT, &dfl_cnt); + if (dfl_cnt > PCI_STD_NUM_BARS) { + dev_err(&pcidev->dev, "%s too many DFLs %d > %d\n", + __func__, dfl_cnt, PCI_STD_NUM_BARS); + return -EINVAL; + } + + dfl_res_off = voff + PCI_VNDR_DFLS_RES; + if (dfl_res_off + (dfl_cnt * sizeof(u32)) > PCI_CFG_SPACE_EXP_SIZE) { + dev_err(&pcidev->dev, "%s DFL VSEC too big for PCIe config space\n", + __func__); + return -EINVAL; + } + + for (i = 0, bars = 0; i < dfl_cnt; i++, dfl_res_off += sizeof(u32)) { + dfl_res = GENMASK(31, 0); + pci_read_config_dword(pcidev, dfl_res_off, &dfl_res); + + bir = dfl_res & PCI_VNDR_DFLS_RES_BAR_MASK; + if (bir >= PCI_STD_NUM_BARS) { + dev_err(&pcidev->dev, "%s bad bir number %d\n", + __func__, bir); + return -EINVAL; } - ret = dfl_fpga_enum_info_add_irq(info, nvec, irq_table); - kfree(irq_table); - if (ret) - goto irq_free_exit; + if (bars & BIT(bir)) { + dev_err(&pcidev->dev, "%s DFL for BAR %d already specified\n", + __func__, bir); + return -EINVAL; + } + + bars |= BIT(bir); + + len = pci_resource_len(pcidev, bir); + offset = dfl_res & PCI_VNDR_DFLS_RES_OFF_MASK; + if (offset >= len) { + dev_err(&pcidev->dev, "%s bad offset %u >= %pa\n", + __func__, offset, &len); + return -EINVAL; + } + + dev_dbg(&pcidev->dev, "%s BAR %d offset 0x%x\n", __func__, bir, offset); + + len -= offset; + + start = pci_resource_start(pcidev, bir) + offset; + + dfl_fpga_enum_info_add_dfl(info, start, len); } - /* start to find Device Feature List in Bar 0 */ + return 0; +} + +/* default method of finding dfls starting at offset 0 of bar 0 */ +static int find_dfls_by_default(struct pci_dev *pcidev, + struct dfl_fpga_enum_info *info) +{ + int port_num, bar, i, ret = 0; + resource_size_t start, len; + void __iomem *base; + u32 offset; + u64 v; + + /* start to find Device Feature List from Bar 0 */ base = cci_pci_ioremap_bar0(pcidev); - if (!base) { - ret = -ENOMEM; - goto irq_free_exit; - } + if (!base) + return -ENOMEM; /* * PF device has FME and Ports/AFUs, and VF device only has one @@ -208,12 +261,54 @@ static int cci_enumerate_feature_devs(struct pci_dev *pcidev) dfl_fpga_enum_info_add_dfl(info, start, len); } else { ret = -ENODEV; - goto irq_free_exit; } /* release I/O mappings for next step enumeration */ pcim_iounmap_regions(pcidev, BIT(0)); + return ret; +} + +/* enumerate feature devices under pci device */ +static int cci_enumerate_feature_devs(struct pci_dev *pcidev) +{ + struct cci_drvdata *drvdata = pci_get_drvdata(pcidev); + struct dfl_fpga_enum_info *info; + struct dfl_fpga_cdev *cdev; + int nvec, ret = 0; + int *irq_table; + + /* allocate enumeration info via pci_dev */ + info = dfl_fpga_enum_info_alloc(&pcidev->dev); + if (!info) + return -ENOMEM; + + /* add irq info for enumeration if the device support irq */ + nvec = cci_pci_alloc_irq(pcidev); + if (nvec < 0) { + dev_err(&pcidev->dev, "Fail to alloc irq %d.\n", nvec); + ret = nvec; + goto enum_info_free_exit; + } else if (nvec) { + irq_table = cci_pci_create_irq_table(pcidev, nvec); + if (!irq_table) { + ret = -ENOMEM; + goto irq_free_exit; + } + + ret = dfl_fpga_enum_info_add_irq(info, nvec, irq_table); + kfree(irq_table); + if (ret) + goto irq_free_exit; + } + + ret = find_dfls_by_vsec(pcidev, info); + if (ret == -ENODEV) + ret = find_dfls_by_default(pcidev, info); + + if (ret) + goto irq_free_exit; + /* start enumeration with prepared enumeration information */ cdev = dfl_fpga_feature_devs_enumerate(info); if (IS_ERR(cdev)) { diff --git a/drivers/fpga/dfl.c b/drivers/fpga/dfl.c index b450870b75ed..511b20ff35a3 100644 --- a/drivers/fpga/dfl.c +++ b/drivers/fpga/dfl.c @@ -10,6 +10,7 @@ * Wu Hao <hao.wu@intel.com> * Xiao Guangrong <guangrong.xiao@linux.intel.com> */ +#include <linux/dfl.h> #include <linux/fpga-dfl.h> #include <linux/module.h> #include <linux/uaccess.h> @@ -298,8 +299,7 @@ static int dfl_bus_uevent(struct device *dev, struct kobj_uevent_env *env) { struct dfl_device *ddev = to_dfl_dev(dev); - /* The type has 4 valid bits and feature_id has 12 valid bits */ - return add_uevent_var(env, "MODALIAS=dfl:t%01Xf%03X", + return add_uevent_var(env, "MODALIAS=dfl:t%04Xf%04X", ddev->type, ddev->feature_id); } diff --git a/drivers/fpga/dfl.h b/drivers/fpga/dfl.h index 5dc758f655b7..2b82c96ba56c 100644 --- a/drivers/fpga/dfl.h +++ b/drivers/fpga/dfl.h @@ -22,6 +22,7 @@ #include <linux/interrupt.h> #include <linux/iopoll.h> #include <linux/io-64-nonatomic-lo-hi.h> +#include <linux/mod_devicetable.h> #include <linux/platform_device.h> #include <linux/slab.h> #include <linux/uuid.h> @@ -516,88 +517,4 @@ long dfl_feature_ioctl_set_irq(struct platform_device *pdev, struct dfl_feature *feature, unsigned long arg); -/** - * enum dfl_id_type - define the DFL FIU types - */ -enum dfl_id_type { - FME_ID, - PORT_ID, - DFL_ID_MAX, -}; - -/** - * struct dfl_device_id - dfl device identifier - * @type: contains 4 bits DFL FIU type of the device. See enum dfl_id_type. - * @feature_id: contains 12 bits feature identifier local to its DFL FIU type. - * @driver_data: driver specific data. - */ -struct dfl_device_id { - u8 type; - u16 feature_id; - unsigned long driver_data; -}; - -/** - * struct dfl_device - represent an dfl device on dfl bus - * - * @dev: generic device interface. - * @id: id of the dfl device. - * @type: type of DFL FIU of the device. See enum dfl_id_type. - * @feature_id: 16 bits feature identifier local to its DFL FIU type. - * @mmio_res: mmio resource of this dfl device. - * @irqs: list of Linux IRQ numbers of this dfl device. - * @num_irqs: number of IRQs supported by this dfl device. - * @cdev: pointer to DFL FPGA container device this dfl device belongs to. - * @id_entry: matched id entry in dfl driver's id table. - */ -struct dfl_device { - struct device dev; - int id; - u8 type; - u16 feature_id; - struct resource mmio_res; - int *irqs; - unsigned int num_irqs; - struct dfl_fpga_cdev *cdev; - const struct dfl_device_id *id_entry; -}; - -/** - * struct dfl_driver - represent an dfl device driver - * - * @drv: driver model structure. - * @id_table: pointer to table of device IDs the driver is interested in. - * { } member terminated. - * @probe: mandatory callback for device binding. - * @remove: callback for device unbinding. - */ -struct dfl_driver { - struct device_driver drv; - const struct dfl_device_id *id_table; - - int (*probe)(struct dfl_device *dfl_dev); - void (*remove)(struct dfl_device *dfl_dev); -}; - -#define to_dfl_dev(d) container_of(d, struct dfl_device, dev) -#define to_dfl_drv(d) container_of(d, struct dfl_driver, drv) - -/* - * use a macro to avoid include chaining to get THIS_MODULE. - */ -#define dfl_driver_register(drv) \ - __dfl_driver_register(drv, THIS_MODULE) -int __dfl_driver_register(struct dfl_driver *dfl_drv, struct module *owner); -void dfl_driver_unregister(struct dfl_driver *dfl_drv); - -/* - * module_dfl_driver() - Helper macro for drivers that don't do - * anything special in module init/exit. This eliminates a lot of - * boilerplate. Each module may only use this macro once, and - * calling it replaces module_init() and module_exit(). - */ -#define module_dfl_driver(__dfl_driver) \ - module_driver(__dfl_driver, dfl_driver_register, \ - dfl_driver_unregister) - #endif /* __FPGA_DFL_H */ |