diff options
Diffstat (limited to 'drivers/mmc/host/sdhci-msm.c')
| -rw-r--r-- | drivers/mmc/host/sdhci-msm.c | 85 |
1 files changed, 82 insertions, 3 deletions
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c index c283291db705..646bf377ba77 100644 --- a/drivers/mmc/host/sdhci-msm.c +++ b/drivers/mmc/host/sdhci-msm.c @@ -21,6 +21,7 @@ #include <linux/pm_runtime.h> #include <linux/slab.h> #include <linux/iopoll.h> +#include <linux/regulator/consumer.h> #include "sdhci-pltfm.h" @@ -77,10 +78,16 @@ #define CORE_HC_MCLK_SEL_DFLT (2 << 8) #define CORE_HC_MCLK_SEL_HS400 (3 << 8) #define CORE_HC_MCLK_SEL_MASK (3 << 8) +#define CORE_IO_PAD_PWR_SWITCH_EN (1 << 15) +#define CORE_IO_PAD_PWR_SWITCH (1 << 16) #define CORE_HC_SELECT_IN_EN BIT(18) #define CORE_HC_SELECT_IN_HS400 (6 << 19) #define CORE_HC_SELECT_IN_MASK (7 << 19) +#define CORE_3_0V_SUPPORT (1 << 25) +#define CORE_1_8V_SUPPORT (1 << 26) +#define CORE_VOLT_SUPPORT (CORE_3_0V_SUPPORT | CORE_1_8V_SUPPORT) + #define CORE_CSR_CDC_CTLR_CFG0 0x130 #define CORE_SW_TRIG_FULL_CALIB BIT(16) #define CORE_HW_AUTOCAL_ENA BIT(17) @@ -148,6 +155,7 @@ struct sdhci_msm_host { u32 curr_io_level; wait_queue_head_t pwr_irq_wait; bool pwr_irq_flag; + u32 caps_0; }; static unsigned int msm_get_clock_rate_for_bus_mode(struct sdhci_host *host, @@ -1103,8 +1111,8 @@ static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq) struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); u32 irq_status, irq_ack = 0; int retry = 10; - int pwr_state = 0, io_level = 0; - + u32 pwr_state = 0, io_level = 0; + u32 config; irq_status = readl_relaxed(msm_host->core_mem + CORE_PWRCTL_STATUS); irq_status &= INT_MASK; @@ -1161,6 +1169,38 @@ static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq) */ writel_relaxed(irq_ack, msm_host->core_mem + CORE_PWRCTL_CTL); + /* + * If we don't have info regarding the voltage levels supported by + * regulators, don't change the IO PAD PWR SWITCH. + */ + if (msm_host->caps_0 & CORE_VOLT_SUPPORT) { + u32 new_config; + /* + * We should unset IO PAD PWR switch only if the register write + * can set IO lines high and the regulator also switches to 3 V. + * Else, we should keep the IO PAD PWR switch set. + * This is applicable to certain targets where eMMC vccq supply + * is only 1.8V. In such targets, even during REQ_IO_HIGH, the + * IO PAD PWR switch must be kept set to reflect actual + * regulator voltage. This way, during initialization of + * controllers with only 1.8V, we will set the IO PAD bit + * without waiting for a REQ_IO_LOW. + */ + config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC); + new_config = config; + + if ((io_level & REQ_IO_HIGH) && + (msm_host->caps_0 & CORE_3_0V_SUPPORT)) + new_config &= ~CORE_IO_PAD_PWR_SWITCH; + else if ((io_level & REQ_IO_LOW) || + (msm_host->caps_0 & CORE_1_8V_SUPPORT)) + new_config |= CORE_IO_PAD_PWR_SWITCH; + + if (config ^ new_config) + writel_relaxed(new_config, + host->ioaddr + CORE_VENDOR_SPEC); + } + if (pwr_state) msm_host->curr_pwr_state = pwr_state; if (io_level) @@ -1313,6 +1353,45 @@ static void sdhci_msm_writeb(struct sdhci_host *host, u8 val, int reg) sdhci_msm_check_power_status(host, req_type); } +static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host) +{ + struct mmc_host *mmc = msm_host->mmc; + struct regulator *supply = mmc->supply.vqmmc; + u32 caps = 0, config; + struct sdhci_host *host = mmc_priv(mmc); + + if (!IS_ERR(mmc->supply.vqmmc)) { + if (regulator_is_supported_voltage(supply, 1700000, 1950000)) + caps |= CORE_1_8V_SUPPORT; + if (regulator_is_supported_voltage(supply, 2700000, 3600000)) + caps |= CORE_3_0V_SUPPORT; + + if (!caps) + pr_warn("%s: 1.8/3V not supported for vqmmc\n", + mmc_hostname(mmc)); + } + + if (caps) { + /* + * Set the PAD_PWR_SWITCH_EN bit so that the PAD_PWR_SWITCH + * bit can be used as required later on. + */ + u32 io_level = msm_host->curr_io_level; + + config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC); + config |= CORE_IO_PAD_PWR_SWITCH_EN; + + if ((io_level & REQ_IO_HIGH) && (caps & CORE_3_0V_SUPPORT)) + config &= ~CORE_IO_PAD_PWR_SWITCH; + else if ((io_level & REQ_IO_LOW) || (caps & CORE_1_8V_SUPPORT)) + config |= CORE_IO_PAD_PWR_SWITCH; + + writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC); + } + msm_host->caps_0 |= caps; + pr_debug("%s: supported caps: 0x%08x\n", mmc_hostname(mmc), caps); +} + static const struct of_device_id sdhci_msm_dt_match[] = { { .compatible = "qcom,sdhci-msm-v4" }, {}, @@ -1333,7 +1412,6 @@ static const struct sdhci_ops sdhci_msm_ops = { static const struct sdhci_pltfm_data sdhci_msm_pdata = { .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION | - SDHCI_QUIRK_NO_CARD_NO_RESET | SDHCI_QUIRK_SINGLE_POWER_WRITE | SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN, .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN, @@ -1530,6 +1608,7 @@ static int sdhci_msm_probe(struct platform_device *pdev) ret = sdhci_add_host(host); if (ret) goto pm_runtime_disable; + sdhci_msm_set_regulator_caps(msm_host); pm_runtime_mark_last_busy(&pdev->dev); pm_runtime_put_autosuspend(&pdev->dev); |