summaryrefslogtreecommitdiff
path: root/include/linux/spi/spi.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/linux/spi/spi.h')
-rw-r--r--include/linux/spi/spi.h27
1 files changed, 25 insertions, 2 deletions
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index e1b3e69aeddc..887116dbce2c 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -74,7 +74,7 @@ struct spi_device {
struct spi_master *master;
u32 max_speed_hz;
u8 chip_select;
- u8 mode;
+ u16 mode;
#define SPI_CPHA 0x01 /* clock phase */
#define SPI_CPOL 0x02 /* clock polarity */
#define SPI_MODE_0 (0|0) /* (original MicroWire) */
@@ -87,6 +87,10 @@ struct spi_device {
#define SPI_LOOP 0x20 /* loopback mode */
#define SPI_NO_CS 0x40 /* 1 dev/bus, no chipselect */
#define SPI_READY 0x80 /* slave pulls low to pause */
+#define SPI_TX_DUAL 0x100 /* transmit with 2 wires */
+#define SPI_TX_QUAD 0x200 /* transmit with 4 wires */
+#define SPI_RX_DUAL 0x400 /* receive with 2 wires */
+#define SPI_RX_QUAD 0x800 /* receive with 4 wires */
u8 bits_per_word;
int irq;
void *controller_state;
@@ -256,6 +260,9 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
* @busy: message pump is busy
* @running: message pump is running
* @rt: whether this queue is set to run as a realtime task
+ * @auto_runtime_pm: the core should ensure a runtime PM reference is held
+ * while the hardware is prepared, using the parent
+ * device for the spidev
* @prepare_transfer_hardware: a message will soon arrive from the queue
* so the subsystem requests the driver to prepare the transfer hardware
* by issuing this call
@@ -380,11 +387,13 @@ struct spi_master {
bool busy;
bool running;
bool rt;
+ bool auto_runtime_pm;
int (*prepare_transfer_hardware)(struct spi_master *master);
int (*transfer_one_message)(struct spi_master *master,
struct spi_message *mesg);
int (*unprepare_transfer_hardware)(struct spi_master *master);
+
/* gpio chip select */
int *cs_gpios;
};
@@ -454,6 +463,10 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum);
* @rx_buf: data to be read (dma-safe memory), or NULL
* @tx_dma: DMA address of tx_buf, if @spi_message.is_dma_mapped
* @rx_dma: DMA address of rx_buf, if @spi_message.is_dma_mapped
+ * @tx_nbits: number of bits used for writting. If 0 the default
+ * (SPI_NBITS_SINGLE) is used.
+ * @rx_nbits: number of bits used for reading. If 0 the default
+ * (SPI_NBITS_SINGLE) is used.
* @len: size of rx and tx buffers (in bytes)
* @speed_hz: Select a speed other than the device default for this
* transfer. If 0 the default (from @spi_device) is used.
@@ -508,6 +521,11 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum);
* by the results of previous messages and where the whole transaction
* ends when the chipselect goes intactive.
*
+ * When SPI can transfer in 1x,2x or 4x. It can get this tranfer information
+ * from device through @tx_nbits and @rx_nbits. In Bi-direction, these
+ * two should both be set. User can set transfer mode with SPI_NBITS_SINGLE(1x)
+ * SPI_NBITS_DUAL(2x) and SPI_NBITS_QUAD(4x) to support these three transfer.
+ *
* The code that submits an spi_message (and its spi_transfers)
* to the lower layers is responsible for managing its memory.
* Zero-initialize every field you don't set up explicitly, to
@@ -528,6 +546,11 @@ struct spi_transfer {
dma_addr_t rx_dma;
unsigned cs_change:1;
+ u8 tx_nbits;
+ u8 rx_nbits;
+#define SPI_NBITS_SINGLE 0x01 /* 1bit transfer */
+#define SPI_NBITS_DUAL 0x02 /* 2bits transfer */
+#define SPI_NBITS_QUAD 0x04 /* 4bits transfer */
u8 bits_per_word;
u16 delay_usecs;
u32 speed_hz;
@@ -876,7 +899,7 @@ struct spi_board_info {
/* mode becomes spi_device.mode, and is essential for chips
* where the default of SPI_CS_HIGH = 0 is wrong.
*/
- u8 mode;
+ u16 mode;
/* ... may need additional spi_device chip config data here.
* avoid stuff protocol drivers can set; but include stuff