| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
All of these have been in linux-next with no issues for a while"
* tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (67 commits)
tty: serial: qcom_geni_serial: Add 51.2MHz frequency support
tty: serial: imx: clear Ageing Timer Interrupt in handler
serial: 8250_fintek: Add F81966 Support
sc16is7xx: Add flag to activate IrDA mode
dt-bindings: sc16is7xx: Add flag to activate IrDA mode
serial: 8250: Support rs485 bus termination GPIO
serial: 8520_port: Fix function param documentation
dt-bindings: serial: Add binding for rs485 bus termination GPIO
vt: keyboard: avoid signed integer overflow in k_ascii
serial: 8250: Enable 16550A variants by default on non-x86
tty: hvc_console, fix crashes on parallel open/close
serial: imx: Initialize lock for non-registered console
sc16is7xx: Read the LSR register for basic device presence check
sc16is7xx: Allow sharing the IRQ line
sc16is7xx: Use threaded IRQ
sc16is7xx: Always use falling edge IRQ
tty: n_gsm: Fix bogus i++ in gsm_data_kick
tty: n_gsm: Remove unnecessary test in gsm_print_packet()
serial: stm32: add no_console_suspend support
tty: serial: fsl_lpuart: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM/SoC driver updates from Arnd Bergmann:
"These are updates to SoC specific drivers that did not have another
subsystem maintainer tree to go through for some reason:
- Some bus and memory drivers for the MIPS P5600 based Baikal-T1 SoC
that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3, Qualcomm
MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas RZ/G1H, and
Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC as a
transport.
- Mediatek platforms now use a new driver for their "MMSYS" hardware
block that controls clocks and some other aspects in behalf of the
media and gpu drivers.
- Some Tegra processors have improved power management support,
including getting woken up by the PMIC and cluster power down
during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon, Mediatek, and
Tegra"
* tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (155 commits)
clk: sprd: fix compile-testing
bus: bt1-axi: Build the driver into the kernel
bus: bt1-apb: Build the driver into the kernel
bus: bt1-axi: Use sysfs_streq instead of strncmp
bus: bt1-axi: Optimize the return points in the driver
bus: bt1-apb: Use sysfs_streq instead of strncmp
bus: bt1-apb: Use PTR_ERR_OR_ZERO to return from request-regs method
bus: bt1-apb: Fix show/store callback identations
bus: bt1-apb: Include linux/io.h
dt-bindings: memory: Add Baikal-T1 L2-cache Control Block binding
memory: Add Baikal-T1 L2-cache Control Block driver
bus: Add Baikal-T1 APB-bus driver
bus: Add Baikal-T1 AXI-bus driver
dt-bindings: bus: Add Baikal-T1 APB-bus binding
dt-bindings: bus: Add Baikal-T1 AXI-bus binding
staging: tegra-video: fix V4L2 dependency
tee: fix crypto select
drivers: soc: ti: knav_qmss_queue: Make knav_gp_range_ops static
soc: ti: add k3 platforms chipid module driver
dt-bindings: soc: ti: add binding for k3 platforms chipid module
...
|
|
kmap_atomic_prot() is now exported by all architectures. Use this
function rather than open coding a driver specific kmap_atomic.
[arnd@arndb.de: include linux/highmem.h]
Link: http://lkml.kernel.org/r/20200508220150.649044-1-arnd@arndb.de
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Zankel <chris@zankel.net>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Helge Deller <deller@gmx.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20200507150004.1423069-12-ira.weiny@intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Media documentation is now split into admin-guide, driver-api and
userspace-api books (a longstanding request from Jon);
- The media Kconfig was reorganized, in order to make easier to select
drivers and their dependencies;
- The testing drivers now has a separate directory;
- added a new driver for Rockchip Video Decoder IP;
- The atomisp staging driver was resurrected. It is meant to work with
4 generations of cameras on Atom-based laptops, tablets and cell
phones. So, it seems worth investing time to cleanup this driver and
making it in good shape.
- Added some V4L2 core ancillary routines to help with h264 codecs;
- Added an ov2740 image sensor driver;
- The si2157 gained support for Analog TV, which, in turn, added
support for some cx231xx and cx23885 boards to also support analog
standards;
- Added some V4L2 controls (V4L2_CID_CAMERA_ORIENTATION and
V4L2_CID_CAMERA_SENSOR_ROTATION) to help identifying where the camera
is located at the device;
- VIDIOC_ENUM_FMT was extended to support MC-centric devices;
- Lots of drivers improvements and cleanups.
* tag 'media/v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (503 commits)
media: Documentation: media: Refer to mbus format documentation from CSI-2 docs
media: s5k5baf: Replace zero-length array with flexible-array
media: i2c: imx219: Drop <linux/clk-provider.h> and <linux/clkdev.h>
media: i2c: Add ov2740 image sensor driver
media: ov8856: Implement sensor module revision identification
media: ov8856: Add devicetree support
media: dt-bindings: ov8856: Document YAML bindings
media: dvb-usb: Add Cinergy S2 PCIe Dual Port support
media: dvbdev: Fix tuner->demod media controller link
media: dt-bindings: phy: phy-rockchip-dphy-rx0: move rockchip dphy rx0 bindings out of staging
media: staging: dt-bindings: phy-rockchip-dphy-rx0: remove non-used reg property
media: atomisp: unify the version for isp2401 a0 and b0 versions
media: atomisp: update TODO with the current data
media: atomisp: adjust some code at sh_css that could be broken
media: atomisp: don't produce errs for ignored IRQs
media: atomisp: print IRQ when debugging
media: atomisp: isp_mmu: don't use kmem_cache
media: atomisp: add a notice about possible leak resources
media: atomisp: disable the dynamic and reserved pools
media: atomisp: turn on camera before setting it
...
|
|
This code was using get_user_pages*(), in a "Case 2" scenario (DMA/RDMA),
using the categorization from [1]. That means that it's time to convert
the get_user_pages*() + put_page() calls to pin_user_pages*() +
unpin_user_pages() calls.
There is some helpful background in [2]: basically, this is a small part
of fixing a long-standing disconnect between pinning pages, and file
systems' use of those pages.
[1] Documentation/core-api/pin_user_pages.rst
[2] "Explicit pinning of user-space pages":
https://lwn.net/Articles/807108/
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: "Joonas Lahtinen" <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Link: http://lkml.kernel.org/r/20200519002124.2025955-5-jhubbard@nvidia.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull drm updates from Dave Airlie:
"Highlights:
- Core DRM had a lot of refactoring around managed drm resources to
make drivers simpler.
- Intel Tigerlake support is on by default
- amdgpu now support p2p PCI buffer sharing and encrypted GPU memory
Details:
core:
- uapi: error out EBUSY when existing master
- uapi: rework SET/DROP MASTER permission handling
- remove drm_pci.h
- drm_pci* are now legacy
- introduced managed DRM resources
- subclassing support for drm_framebuffer
- simple encoder helper
- edid improvements
- vblank + writeback documentation improved
- drm/mm - optimise tree searches
- port drivers to use devm_drm_dev_alloc
dma-buf:
- add flag for p2p buffer support
mst:
- ACT timeout improvements
- remove drm_dp_mst_has_audio
- don't use 2nd TX slot - spec recommends against it
bridge:
- dw-hdmi various improvements
- chrontel ch7033 support
- fix stack issues with old gcc
hdmi:
- add unpack function for drm infoframe
fbdev:
- misc fbdev driver fixes
i915:
- uapi: global sseu pinning
- uapi: OA buffer polling
- uapi: remove generated perf code
- uapi: per-engine default property values in sysfs
- Tigerlake GEN12 enabled.
- Lots of gem refactoring
- Tigerlake enablement patches
- move to drm_device logging
- Icelake gamma HW readout
- push MST link retrain to hotplug work
- bandwidth atomic helpers
- ICL fixes
- RPS/GT refactoring
- Cherryview full-ppgtt support
- i915 locking guidelines documented
- require linear fb stride to be 512 multiple on gen9
- Tigerlake SAGV support
amdgpu:
- uapi: encrypted GPU memory handling
- uapi: add MEM_SYNC IB flag
- p2p dma-buf support
- export VRAM dma-bufs
- FRU chip access support
- RAS/SR-IOV updates
- Powerplay locking fixes
- VCN DPG (powergating) enablement
- GFX10 clockgating fixes
- DC fixes
- GPU reset fixes
- navi SDMA fix
- expose FP16 for modesetting
- DP 1.4 compliance fixes
- gfx10 soft recovery
- Improved Critical Thermal Faults handling
- resizable BAR on gmc10
amdkfd:
- uapi: GWS resource management
- track GPU memory per process
- report PCI domain in topology
radeon:
- safe reg list generator fixes
nouveau:
- HD audio fixes on recent systems
- vGPU detection (fail probe if we're on one, for now)
- Interlaced mode fixes (mostly avoidance on Turing, which doesn't support it)
- SVM improvements/fixes
- NVIDIA format modifier support
- Misc other fixes.
adv7511:
- HDMI SPDIF support
ast:
- allocate crtc state size
- fix double assignment
- fix suspend
bochs:
- drop connector register
cirrus:
- move to tiny drivers.
exynos:
- fix imported dma-buf mapping
- enable runtime PM
- fixes and cleanups
mediatek:
- DPI pin mode swap
- config mipi_tx current/impedance
lima:
- devfreq + cooling device support
- task handling improvements
- runtime PM support
pl111:
- vexpress init improvements
- fix module auto-load
rcar-du:
- DT bindings conversion to YAML
- Planes zpos sanity check and fix
- MAINTAINERS entry for LVDS panel driver
mcde:
- fix return value
mgag200:
- use managed config init
stm:
- read endpoints from DT
vboxvideo:
- use PCI managed functions
- drop WC mtrr
vkms:
- enable cursor by default
rockchip:
- afbc support
virtio:
- various cleanups
qxl:
- fix cursor notify port
hisilicon:
- 128-byte stride alignment fix
sun4i:
- improved format handling"
* tag 'drm-next-2020-06-02' of git://anongit.freedesktop.org/drm/drm: (1401 commits)
drm/amd/display: Fix potential integer wraparound resulting in a hang
drm/amd/display: drop cursor position check in atomic test
drm/amdgpu: fix device attribute node create failed with multi gpu
drm/nouveau: use correct conflicting framebuffer API
drm/vblank: Fix -Wformat compile warnings on some arches
drm/amdgpu: Sync with VM root BO when switching VM to CPU update mode
drm/amd/display: Handle GPU reset for DC block
drm/amdgpu: add apu flags (v2)
drm/amd/powerpay: Disable gfxoff when setting manual mode on picasso and raven
drm/amdgpu: fix pm sysfs node handling (v2)
drm/amdgpu: move gpu_info parsing after common early init
drm/amdgpu: move discovery gfx config fetching
drm/nouveau/dispnv50: fix runtime pm imbalance on error
drm/nouveau: fix runtime pm imbalance on error
drm/nouveau: fix runtime pm imbalance on error
drm/nouveau/debugfs: fix runtime pm imbalance on error
drm/nouveau/nouveau/hmm: fix migrate zero page to GPU
drm/nouveau/nouveau/hmm: fix nouveau_dmem_chunk allocations
drm/nouveau/kms/nv50-: Share DP SST mode_valid() handling with MST
drm/nouveau/kms/nv50-: Move 8BPC limit for MST into nv50_mstc_get_modes()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull hmm updates from Jason Gunthorpe:
"This series adds a selftest for hmm_range_fault() and several of the
DEVICE_PRIVATE migration related actions, and another simplification
for hmm_range_fault()'s API.
- Simplify hmm_range_fault() with a simpler return code, no
HMM_PFN_SPECIAL, and no customizable output PFN format
- Add a selftest for hmm_range_fault() and DEVICE_PRIVATE related
functionality"
* tag 'for-linus-hmm' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
MAINTAINERS: add HMM selftests
mm/hmm/test: add selftests for HMM
mm/hmm/test: add selftest driver for HMM
mm/hmm: remove the customizable pfn format from hmm_range_fault
mm/hmm: remove HMM_PFN_SPECIAL
drm/amdgpu: remove dead code after hmm_range_fault()
mm/hmm: make hmm_range_fault return 0 or -1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These rework the system-wide PM driver flags, make runtime switching
of cpuidle governors easier, improve the user space hibernation
interface code, add intel-speed-select interface documentation, add
more debug messages to the ACPI code handling suspend to idle, update
the cpufreq core and drivers, fix a minor issue in the cpuidle core
and update two cpuidle drivers, improve the PM-runtime framework,
update the Intel RAPL power capping driver, update devfreq core and
drivers, and clean up the cpupower utility.
Specifics:
- Rework the system-wide PM driver flags to make them easier to
understand and use and update their documentation (Rafael Wysocki,
Alan Stern).
- Allow cpuidle governors to be switched at run time regardless of
the kernel configuration and update the related documentation
accordingly (Hanjun Guo).
- Improve the resume device handling in the user space hibernarion
interface code (Domenico Andreoli).
- Document the intel-speed-select sysfs interface (Srinivas
Pandruvada).
- Make the ACPI code handing suspend to idle print more debug
messages to help diagnose issues with it (Rafael Wysocki).
- Fix a helper routine in the cpufreq core and correct a typo in the
struct cpufreq_driver kerneldoc comment (Rafael Wysocki, Wang
Wenhu).
- Update cpufreq drivers:
- Make the intel_pstate driver start in the passive mode by
default on systems without HWP (Rafael Wysocki).
- Add i.MX7ULP support to the imx-cpufreq-dt driver and add
i.MX7ULP to the cpufreq-dt-platdev blacklist (Peng Fan).
- Convert the qoriq cpufreq driver to a platform one, make the
platform code create a suitable device object for it and add
platform dependencies to it (Mian Yousaf Kaukab, Geert
Uytterhoeven).
- Fix wrong compatible binding in the qcom driver (Ansuel Smith).
- Build the omap driver by default for ARCH_OMAP2PLUS (Anders
Roxell).
- Add r8a7742 SoC support to the dt cpufreq driver (Lad
Prabhakar).
- Update cpuidle core and drivers:
- Fix three reference count leaks in error code paths in the
cpuidle core (Qiushi Wu).
- Convert Qualcomm SPM to a generic cpuidle driver (Stephan
Gerhold).
- Fix up the execution order when entering a domain idle state in
the PSCI driver (Ulf Hansson).
- Fix a reference counting issue related to clock management and
clean up two oddities in the PM-runtime framework (Rafael Wysocki,
Andy Shevchenko).
- Add ElkhartLake support to the Intel RAPL power capping driver and
remove an unused local MSR definition from it (Jacob Pan, Sumeet
Pawnikar).
- Update devfreq core and drivers:
- Replace strncpy() with strscpy() in the devfreq core and use
lockdep asserts instead of manual checks for a locked mutex in
it (Dmitry Osipenko, Krzysztof Kozlowski).
- Add a generic imx bus scaling driver and make it register an
interconnect device (Leonard Crestez, Gustavo A. R. Silva).
- Make the cpufreq notifier in the tegra30 driver take boosting
into account and delete an unuseful error message from that
driver (Dmitry Osipenko, Markus Elfring).
- Remove unneeded semicolon from the cpupower code (Zou Wei)"
* tag 'pm-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (51 commits)
cpuidle: Fix three reference count leaks
PM: runtime: Replace pm_runtime_callbacks_present()
PM / devfreq: Use lockdep asserts instead of manual checks for locked mutex
PM / devfreq: imx-bus: Fix inconsistent IS_ERR and PTR_ERR
PM / devfreq: Replace strncpy with strscpy
PM / devfreq: imx: Register interconnect device
PM / devfreq: Add generic imx bus scaling driver
PM / devfreq: tegra30: Delete an error message in tegra_devfreq_probe()
PM / devfreq: tegra30: Make CPUFreq notifier to take into account boosting
PM: hibernate: Restrict writes to the resume device
PM: runtime: clk: Fix clk_pm_runtime_get() error path
cpuidle: Convert Qualcomm SPM driver to a generic CPUidle driver
ACPI: EC: PM: s2idle: Extend GPE dispatching debug message
ACPI: PM: s2idle: Print type of wakeup debug messages
powercap: RAPL: remove unused local MSR define
PM: runtime: Make clear what we do when conditions are wrong in rpm_suspend()
Documentation: admin-guide: pm: Document intel-speed-select
PM: hibernate: Split off snapshot dev option
PM: hibernate: Incorporate concurrency handling
Documentation: ABI: make current_governer_ro as a candidate for removal
...
|
|
Merge updates from Andrew Morton:
"A few little subsystems and a start of a lot of MM patches.
Subsystems affected by this patch series: squashfs, ocfs2, parisc,
vfs. With mm subsystems: slab-generic, slub, debug, pagecache, gup,
swap, memcg, pagemap, memory-failure, vmalloc, kasan"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
kasan: move kasan_report() into report.c
mm/mm_init.c: report kasan-tag information stored in page->flags
ubsan: entirely disable alignment checks under UBSAN_TRAP
kasan: fix clang compilation warning due to stack protector
x86/mm: remove vmalloc faulting
mm: remove vmalloc_sync_(un)mappings()
x86/mm/32: implement arch_sync_kernel_mappings()
x86/mm/64: implement arch_sync_kernel_mappings()
mm/ioremap: track which page-table levels were modified
mm/vmalloc: track which page-table levels were modified
mm: add functions to track page directory modifications
s390: use __vmalloc_node in stack_alloc
powerpc: use __vmalloc_node in alloc_vm_stack
arm64: use __vmalloc_node in arch_alloc_vmap_stack
mm: remove vmalloc_user_node_flags
mm: switch the test_vmalloc module to use __vmalloc_node
mm: remove __vmalloc_node_flags_caller
mm: remove both instances of __vmalloc_node_flags
mm: remove the prot argument to __vmalloc_node
mm: remove the pgprot argument to __vmalloc
...
|
|
The pgprot argument to __vmalloc is always PAGE_KERNEL now, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com> [hyperv]
Acked-by: Gao Xiang <xiang@kernel.org> [erofs]
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200414131348.444715-22-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The non-cached vmalloc mapping was initially added as a hack for the
first-gen amigaone platform (6xx/book32s), isn't fully supported upstream,
and which used the legacy radeon driver together with non-coherent DMA.
However this only ever worked reliably for DRI .
Remove the hack as it is the last user of __vmalloc passing a page
protection flag other than PAGE_KERNEL and didn't do anything for other
platforms with non-coherent DMA.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: David Airlie <airlied@linux.ie>
Cc: Gao Xiang <xiang@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200414131348.444715-21-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is always PAGE_KERNEL - for long term mappings with other properties
vmap should be used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Gao Xiang <xiang@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200414131348.444715-19-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Doing a "get_user_pages()" on a copy-on-write page for reading can be
ambiguous: the page can be COW'ed at any time afterwards, and the
direction of a COW event isn't defined.
Yes, whoever writes to it will generally do the COW, but if the thread
that did the get_user_pages() unmapped the page before the write (and
that could happen due to memory pressure in addition to any outright
action), the writer could also just take over the old page instead.
End result: the get_user_pages() call might result in a page pointer
that is no longer associated with the original VM, and is associated
with - and controlled by - another VM having taken it over instead.
So when doing a get_user_pages() on a COW mapping, the only really safe
thing to do would be to break the COW when getting the page, even when
only getting it for reading.
At the same time, some users simply don't even care.
For example, the perf code wants to look up the page not because it
cares about the page, but because the code simply wants to look up the
physical address of the access for informational purposes, and doesn't
really care about races when a page might be unmapped and remapped
elsewhere.
This adds logic to force a COW event by setting FOLL_WRITE on any
copy-on-write mapping when FOLL_GET (or FOLL_PIN) is used to get a page
pointer as a result.
The current semantics end up being:
- __get_user_pages_fast(): no change. If you don't ask for a write,
you won't break COW. You'd better know what you're doing.
- get_user_pages_fast(): the fast-case "look it up in the page tables
without anything getting mmap_sem" now refuses to follow a read-only
page, since it might need COW breaking. Which happens in the slow
path - the fast path doesn't know if the memory might be COW or not.
- get_user_pages() (including the slow-path fallback for gup_fast()):
for a COW mapping, turn on FOLL_WRITE for FOLL_GET/FOLL_PIN, with
very similar semantics to FOLL_FORCE.
If it turns out that we want finer granularity (ie "only break COW when
it might actually matter" - things like the zero page are special and
don't need to be broken) we might need to push these semantics deeper
into the lookup fault path. So if people care enough, it's possible
that we might end up adding a new internal FOLL_BREAK_COW flag to go
with the internal FOLL_COW flag we already have for tracking "I had a
COW".
Alternatively, if it turns out that different callers might want to
explicitly control the forced COW break behavior, we might even want to
make such a flag visible to the users of get_user_pages() instead of
using the above default semantics.
But for now, this is mostly commentary on the issue (this commit message
being a lot bigger than the patch, and that patch in turn is almost all
comments), with that minimal "enable COW breaking early" logic using the
existing FOLL_WRITE behavior.
[ It might be worth noting that we've always had this ambiguity, and it
could arguably be seen as a user-space issue.
You only get private COW mappings that could break either way in
situations where user space is doing cooperative things (ie fork()
before an execve() etc), but it _is_ surprising and very subtle, and
fork() is supposed to give you independent address spaces.
So let's treat this as a kernel issue and make the semantics of
get_user_pages() easier to understand. Note that obviously a true
shared mapping will still get a page that can change under us, so this
does _not_ mean that get_user_pages() somehow returns any "stable"
page ]
Reported-by: Jann Horn <jannh@google.com>
Tested-by: Christoph Hellwig <hch@lst.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kirill Shutemov <kirill@shutemov.name>
Acked-by: Jan Kara <jack@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull uaccess/readdir updates from Al Viro:
"Finishing the conversion of readdir.c to unsafe_... API.
This includes the uaccess_{read,write}_begin series by Christophe
Leroy"
* 'uaccess.readdir' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
readdir.c: get rid of the last __put_user(), drop now-useless access_ok()
readdir.c: get compat_filldir() more or less in sync with filldir()
switch readdir(2) to unsafe_copy_dirent_name()
drm/i915/gem: Replace user_access_begin by user_write_access_begin
uaccess: Selectively open read or write user access
uaccess: Add user_read_access_begin/end and user_write_access_begin/end
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull uaccess/access_ok updates from Al Viro:
"Removals of trivially pointless access_ok() calls.
Note: the fiemap stuff was removed from the series, since they are
duplicates with part of ext4 series carried in Ted's tree"
* 'uaccess.access_ok' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vmci_host: get rid of pointless access_ok()
hfi1: get rid of pointless access_ok()
usb: get rid of pointless access_ok() calls
lpfc_debugfs: get rid of pointless access_ok()
efi_test: get rid of pointless access_ok()
drm_read(): get rid of pointless access_ok()
via-pmu: don't bother with access_ok()
drivers/crypto/ccp/sev-dev.c: get rid of pointless access_ok()
omapfb: get rid of pointless access_ok() calls
amifb: get rid of pointless access_ok() calls
drivers/fpga/dfl-afu-dma-region.c: get rid of pointless access_ok()
drivers/fpga/dfl-fme-pr.c: get rid of pointless access_ok()
cm4000_cs.c cmm_ioctl(): get rid of pointless access_ok()
nvram: drop useless access_ok()
n_hdlc_tty_read(): remove pointless access_ok()
tomoyo_write_control(): get rid of pointless access_ok()
btrfs_ioctl_send(): don't bother with access_ok()
fat_dir_ioctl(): hadn't needed that access_ok() for more than a decade...
dlmfs_file_write(): get rid of pointless access_ok()
|
|
Pull documentation updates from Jonathan Corbet:
"A fair amount of stuff this time around, dominated by yet another
massive set from Mauro toward the completion of the RST conversion. I
*really* hope we are getting close to the end of this. Meanwhile,
those patches reach pretty far afield to update document references
around the tree; there should be no actual code changes there. There
will be, alas, more of the usual trivial merge conflicts.
Beyond that we have more translations, improvements to the sphinx
scripting, a number of additions to the sysctl documentation, and lots
of fixes"
* tag 'docs-5.8' of git://git.lwn.net/linux: (130 commits)
Documentation: fixes to the maintainer-entry-profile template
zswap: docs/vm: Fix typo accept_threshold_percent in zswap.rst
tracing: Fix events.rst section numbering
docs: acpi: fix old http link and improve document format
docs: filesystems: add info about efivars content
Documentation: LSM: Correct the basic LSM description
mailmap: change email for Ricardo Ribalda
docs: sysctl/kernel: document unaligned controls
Documentation: admin-guide: update bug-hunting.rst
docs: sysctl/kernel: document ngroups_max
nvdimm: fixes to maintainter-entry-profile
Documentation/features: Correct RISC-V kprobes support entry
Documentation/features: Refresh the arch support status files
Revert "docs: sysctl/kernel: document ngroups_max"
docs: move locking-specific documents to locking/
docs: move digsig docs to the security book
docs: move the kref doc into the core-api book
docs: add IRQ documentation at the core-api book
docs: debugging-via-ohci1394.txt: add it to the core-api book
docs: fix references for ipmi.rst file
...
|
|
Pull ARM updates from Russell King:
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8980/1: Allow either FLATMEM or SPARSEMEM on the multiplatform build
ARM: 8979/1: Remove redundant ARCH_SPARSEMEM_DEFAULT setting
ARM: 8978/1: mm: make act_mm() respect THREAD_SIZE
ARM: decompressor: run decompressor in place if loaded via UEFI
ARM: decompressor: move GOT into .data for EFI enabled builds
ARM: decompressor: defer loading of the contents of the LC0 structure
ARM: decompressor: split off _edata and stack base into separate object
ARM: decompressor: move headroom variable out of LC0
ARM: 8976/1: module: allow arch overrides for .init section names
ARM: 8975/1: module: fix handling of unwind init sections
ARM: 8974/1: use SPARSMEM_STATIC when SPARSEMEM is enabled
ARM: 8971/1: replace the sole use of a symbol with its definition
ARM: 8969/1: decompressor: simplify libfdt builds
Update rmk's email address in various drivers
ARM: compat: remove KERNEL_DS usage in sys_oabi_epoll_ctl()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Add AMD Fam17h RAPL support
- Introduce CAP_PERFMON to kernel and user space
- Add Zhaoxin CPU support
- Misc fixes and cleanups
Tooling changes:
- perf record:
Introduce '--switch-output-event' to use arbitrary events to be
setup and read from a side band thread and, when they take place a
signal be sent to the main 'perf record' thread, reusing the core
for '--switch-output' to take perf.data snapshots from the ring
buffer used for '--overwrite', e.g.:
# perf record --overwrite -e sched:* \
--switch-output-event syscalls:*connect* \
workload
will take perf.data.YYYYMMDDHHMMSS snapshots up to around the
connect syscalls.
Add '--num-synthesize-threads' option to control degree of
parallelism of the synthesize_mmap() code which is scanning
/proc/PID/task/PID/maps and can be time consuming. This mimics
pre-existing behaviour in 'perf top'.
- perf bench:
Add a multi-threaded synthesize benchmark and kallsyms parsing
benchmark.
- Intel PT support:
Stitch LBR records from multiple samples to get deeper backtraces,
there are caveats, see the csets for details.
Allow using Intel PT to synthesize callchains for regular events.
Add support for synthesizing branch stacks for regular events
(cycles, instructions, etc) from Intel PT data.
Misc changes:
- Updated perf vendor events for power9 and Coresight.
- Add flamegraph.py script via 'perf flamegraph'
- Misc other changes, fixes and cleanups - see the Git log for details
Also, since over the last couple of years perf tooling has matured and
decoupled from the kernel perf changes to a large degree, going
forward Arnaldo is going to send perf tooling changes via direct pull
requests"
* tag 'perf-core-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (163 commits)
perf/x86/rapl: Add AMD Fam17h RAPL support
perf/x86/rapl: Make perf_probe_msr() more robust and flexible
perf/x86/rapl: Flip logic on default events visibility
perf/x86/rapl: Refactor to share the RAPL code between Intel and AMD CPUs
perf/x86/rapl: Move RAPL support to common x86 code
perf/core: Replace zero-length array with flexible-array
perf/x86: Replace zero-length array with flexible-array
perf/x86/intel: Add more available bits for OFFCORE_RESPONSE of Intel Tremont
perf/x86/rapl: Add Ice Lake RAPL support
perf flamegraph: Use /bin/bash for report and record scripts
perf cs-etm: Move definition of 'traceid_list' global variable from header file
libsymbols kallsyms: Move hex2u64 out of header
libsymbols kallsyms: Parse using io api
perf bench: Add kallsyms parsing
perf: cs-etm: Update to build with latest opencsd version.
perf symbol: Fix kernel symbol address display
perf inject: Rename perf_evsel__*() operating on 'struct evsel *' to evsel__*()
perf annotate: Rename perf_evsel__*() operating on 'struct evsel *' to evsel__*()
perf trace: Rename perf_evsel__*() operating on 'struct evsel *' to evsel__*()
perf script: Rename perf_evsel__*() operating on 'struct evsel *' to evsel__*()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
"The RCU updates for this cycle were:
- RCU-tasks update, including addition of RCU Tasks Trace for BPF use
and TASKS_RUDE_RCU
- kfree_rcu() updates.
- Remove scheduler locking restriction
- RCU CPU stall warning updates.
- Torture-test updates.
- Miscellaneous fixes and other updates"
* tag 'core-rcu-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
rcu: Allow for smp_call_function() running callbacks from idle
rcu: Provide rcu_irq_exit_check_preempt()
rcu: Abstract out rcu_irq_enter_check_tick() from rcu_nmi_enter()
rcu: Provide __rcu_is_watching()
rcu: Provide rcu_irq_exit_preempt()
rcu: Make RCU IRQ enter/exit functions rely on in_nmi()
rcu/tree: Mark the idle relevant functions noinstr
x86: Replace ist_enter() with nmi_enter()
x86/mce: Send #MC singal from task work
x86/entry: Get rid of ist_begin/end_non_atomic()
sched,rcu,tracing: Avoid tracing before in_nmi() is correct
sh/ftrace: Move arch_ftrace_nmi_{enter,exit} into nmi exception
lockdep: Always inline lockdep_{off,on}()
hardirq/nmi: Allow nested nmi_enter()
arm64: Prepare arch_nmi_enter() for recursion
printk: Disallow instrumenting print_nmi_enter()
printk: Prepare for nested printk_nmi_enter()
rcutorture: Convert ULONG_CMP_LT() to time_before()
torture: Add a --kasan argument
torture: Save a few lines by using config_override_param initially
...
|
|
* pm-core:
PM: runtime: Replace pm_runtime_callbacks_present()
PM: runtime: clk: Fix clk_pm_runtime_get() error path
PM: runtime: Make clear what we do when conditions are wrong in rpm_suspend()
* pm-sleep:
PM: hibernate: Restrict writes to the resume device
PM: hibernate: Split off snapshot dev option
PM: hibernate: Incorporate concurrency handling
PM: sleep: Helpful edits for devices.rst documentation
Documentation: PM: sleep: Update driver flags documentation
PM: sleep: core: Rename DPM_FLAG_LEAVE_SUSPENDED
PM: sleep: core: Rename DPM_FLAG_NEVER_SKIP
PM: sleep: core: Rename dev_pm_smart_suspend_and_suspended()
PM: sleep: core: Rename dev_pm_may_skip_resume()
PM: sleep: core: Rework the power.may_skip_resume handling
PM: sleep: core: Do not skip callbacks in the resume phase
PM: sleep: core: Fold functions into their callers
PM: sleep: core: Simplify the SMART_SUSPEND flag handling
|
|
Pull drm fixes from Dave Airlie:
"A couple of amdgpu fixes and minor ingenic fixes:
amdgpu:
- display atomic test fix
- Fix soft hang in display vupdate code
ingenic:
- fix pointer cast
- fix crtc atomic check callback"
* tag 'drm-fixes-2020-05-29-1' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Fix potential integer wraparound resulting in a hang
drm/amd/display: drop cursor position check in atomic test
gpu/drm: Ingenic: Fix opaque pointer casted to wrong type
gpu/drm: ingenic: Fix bogus crtc_atomic_check callback
|
|
address is passed only to copy_to_user()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Two ingenic fixes, one for a wrong cast, the other for a typo in a
comparison
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200528110944.hanv4qgc6w7whnj3@gilmour.lan
|
|
git://people.freedesktop.org/~agd5f/linux into drm-next
amd-drm-next-5.8-2020-05-27:
amdgpu:
- SRIOV fixes
- RAS fixes
- VCN 2.5 DPG (Dynamic PowerGating) fixes
- FP16 updates for display
- CTF cleanups
- Display fixes
- Fix pcie bw sysfs handling
- Enable resizeable BAR support for gmc 10.x
- GFXOFF fixes for Raven
- PM sysfs handling fixes
amdkfd:
- Fix a race condition
- Warning fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200527231219.3930-1-alexander.deucher@amd.com
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
Short summary of fixes pull (less than what git shortlog provides):
There's a fix for panel brighness on Lenovo X13 Yoga devices and a fix for
-Wformat warnings on architectures where atomic-64 counters are not of
type unsigned long long.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200527080123.GA8186@linux-uq9g
|
|
[Why]
If VUPDATE_END is before VUPDATE_START the delay calculated can become
very large, causing a soft hang.
[How]
Take the absolute value of the difference between START and END.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
get_cursor_position already handles the case where the cursor has
negative off-screen coordinates by not setting
dc_cursor_position.enabled.
Signed-off-by: Simon Ser <contact@emersion.fr>
Fixes: 626bf90fe03f ("drm/amd/display: add basic atomic check for cursor plane")
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If VUPDATE_END is before VUPDATE_START the delay calculated can become
very large, causing a soft hang.
[How]
Take the absolute value of the difference between START and END.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
get_cursor_position already handles the case where the cursor has
negative off-screen coordinates by not setting
dc_cursor_position.enabled.
Signed-off-by: Simon Ser <contact@emersion.fr>
Fixes: 626bf90fe03f ("drm/amd/display: add basic atomic check for cursor plane")
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
- Reverted stricter synchronization for cgroup recursive stats which
was prepping it for event counter usage which never got merged. The
change was causing performation regressions in some cases.
- Restore bpf-based device-cgroup operation even when cgroup1 device
cgroup is disabled.
- An out-param init fix.
* 'for-5.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
device_cgroup: Cleanup cgroup eBPF device filter code
xattr: fix uninitialized out-param
Revert "cgroup: Add memory barriers to plug cgroup_rstat_updated() race window"
|
|
the origin design will use varible of "attr->states" to save node
supported states on current gpu device, but for multi gpu device, when
probe second gpu device, the driver will check attribute node states
from previous gpu device wthether to create attribute node.
it will cause other gpu device create attribute node faild.
1. add member attr_list into amdgpu_device to link supported device attribute node.
2. add new structure "struct amdgpu_device_attr_entry{}" to track device attribute state.
3. drop member "states" from amdgpu_device_attr.
v2:
1. move "attr_list" into amdgpu_pm and rename to "pm_attr_list".
2. refine create & remove device node functions parameter.
fix:
drm/amdgpu: optimize amdgpu device attribute code
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
nouveau was calling the fbdev API which has issues with modules
and built-ins. Call the correct API.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Fixes: 2dd4d163cd9c ("drm/nouveau: remove open-coded version of remove_conflicting_pci_framebuffers()")
Link: https://lore.kernel.org/lkml/21b52c28-3ace-cd13-d8ce-f38f2c6b2a96@infradead.org/T/#u
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/drivers
Refactor the mmsys to reflect that it's a clock driver and
the entry point for the DRM subsystem.
Replace clk-provider.h include with of_clk.h for mach-mediatek
* tag 'v5.7-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
ARM: mediatek: Replace <linux/clk-provider.h> by <linux/of_clk.h>
soc: mediatek: Missing platform_device_unregister() on error in mtk_mmsys_probe()
soc: mediatek: mmsys: Drop <linux/clk-provider.h>
soc / drm: mediatek: Fix mediatek-drm device probing
soc / drm: mediatek: Move routing control to mmsys device
clk / soc: mediatek: Move mt8173 MMSYS to platform driver
dt-bindings: mediatek: Update mmsys binding to reflect it is a system controller
drm/mediatek: Omit warning on probe defers
Link: https://lore.kernel.org/r/2cf27d33-59c6-023b-9993-57a2639824ea@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some architectures like ppc64le and aarch64, compiling with
-Wformat=1 will throw the following warnings:
In file included from drivers/gpu/drm/drm_vblank.c:33:
drivers/gpu/drm/drm_vblank.c: In function 'drm_update_vblank_count':
drivers/gpu/drm/drm_vblank.c:273:16: warning: format '%llu' expects
argument of type 'long long unsigned int', but argument 4 has type
'long int' [-Wformat=]
DRM_DEBUG_VBL("updating vblank count on crtc %u:"
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/drm/drm_print.h:407:22: note: in definition of macro
'DRM_DEBUG_VBL'
drm_dbg(DRM_UT_VBL, fmt, ##__VA_ARGS__)
^~~
drivers/gpu/drm/drm_vblank.c:274:22: note: format string is defined here
" current=%llu, diff=%u, hw=%u hw_last=%u\n",
~~~^
%lu
So, fix that with a typecast.
Co-developed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200521204647.2578479-1-lyude@redhat.com
|
|
This fixes an intermittent bug where a root PD clear operation still in
progress could overwrite a PDE update done by the CPU, resulting in a
VM fault.
Fixes: 108b4d928c03 ("drm/amd/amdgpu: Update VM function pointer")
Reported-by: Jay Cornwall <Jay.Cornwall@amd.com>
Tested-by: Jay Cornwall <Jay.Cornwall@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Previously we used the s3 codepath for gpu reset. This can lead to issues in
certain case where we end of waiting for fences which will never come (because
parts of the hw are off due to gpu reset) and we end up waiting forever causing
a deadlock.
[How]
Handle GPU reset separately from normal s3 case. We essentially need to redo
everything we do in s3, but avoid any drm calls.
For GPU reset case
suspend:
-Acquire DC lock
-Cache current dc_state
-Commit 0 stream/planes to dc (this puts dc into a state where it can be
powered off)
-Disable interrupts
resume
-Edit cached state to force full update
-Commit cached state from suspend
-Build stream and plane updates from the cached state
-Commit stream/plane updates
-Enable interrupts
-Release DC lock
v2:
-Formatting
-Release dc_state
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add some APU flags to simplify handling of different APU
variants. It's easier to understand the special cases
if we use names flags rather than checking device ids and
silicon revisions.
v2: rebase on latest code
Acked-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Problem description]
1. Boot up picasso platform, launches desktop, Don't do anything (APU enter into "gfxoff" state)
2. Remote login to platform using SSH, then type the command line:
sudo su -c "echo manual > /sys/class/drm/card0/device/power_dpm_force_performance_level"
sudo su -c "echo 2 > /sys/class/drm/card0/device/pp_dpm_sclk" (fix SCLK to 1400MHz)
3. Move the mouse around in Window
4. Phenomenon : The screen frozen
Tester will switch sclk level during glmark2 run time.
APU will enter "gfxoff" state intermittently during glmark2 run time.
The system got hanged if fix GFXCLK to 1400MHz when APU is in "gfxoff"
state.
[Debug]
1. Fix SCLK to X MHz
1400: screen frozen, screen black, then OS will reboot.
1300: screen frozen.
1200: screen frozen, screen black.
1100: screen frozen, screen black, then OS will reboot.
1000: screen frozen, screen black.
900: screen frozen, screen black, then OS will reboot.
800: Situation Nomal, issue disappear.
700: Situation Nomal, issue disappear.
2. SBIOS setting: AMD CBS --> SMU Debug Options -->SMU Debug --> "GFX DLDO Psm Margin Control":
50 : Situation Nomal, issue disappear.
45 : Situation Nomal, issue disappear.
40 : Situation Nomal, issue disappear.
35 : Situation Nomal, issue disappear.
30 : screen black.
25 : screen frozen, then blurred screen.
20 : screen frozen.
15 : screen black.
10 : screen frozen.
5 : screen frozen, then blurred screen.
3. Disable GFXOFF feature
Situation Nomal, issue disappear.
[Why]
Through a period of time debugging with Sys Eng team and SMU team, Sys
Eng team said this is voltage/frequency marginal issue not a F/W or H/W
bug. This experiment proves that default targetPsm [for f=1400MHz] is
not sufficient when GFXOFF is enabled on Picasso.
SMU team think it is an odd test conditions to force sclk="1400MHz" when
GPU is in "gfxoff" state，then wake up the GFX. SCLK should be in the
"lowest frequency" when gfxoff.
[How]
Disable gfxoff when setting manual mode.
Enable gfxoff when setting other mode(exiting manual mode) again.
By the way, from the user point of view, now that user switch to manual
mode and force SCLK Frequency, he don't want SCLK be controlled by
workload.It becomes meaningless to "switch to manual mode" if APU enter "gfxoff"
due to lack of workload at this point.
Tips: Same issue observed on Raven.
Signed-off-by: chen gong <curry.gong@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix typos that prevented them from showing up.
v2: switch other files in addition to pp_clk_voltage
Fixes: 4e01847c38f7a5 ("drm/amdgpu: optimize amdgpu device attribute code")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1150
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
|
|
We need to get the silicon revision id before we parse
the firmware in order to load the correct gpu info firmware
for raven2 variants.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1103
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Move it into the fw_info function since it's logically part
of the same functionality.
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- HD audio fixes on recent systems
- vGPU detection (fail probe if we're on one, for now)
- Interlaced mode fixes (mostly avoidance on Turing, which doesn't support it)
- SVM improvements/fixes
- NVIDIA format modifier support
- Misc other fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CACAvsv6DcRFMDVEftdL7LxNtxuSQQ=qnfqdHXO0K=BmJ8Q2-+g@mail.gmail.com
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.8
This include dpi pin mode swap, config mipi_tx current and impedance,
and some fixup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200521014612.17175-1-chunkuang.hu@kernel.org
|
|
pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
When calling OpenCL clEnqueueSVMMigrateMem() on a region of memory that
is backed by pte_none() or zero pages, migrate_vma_setup() will fill the
source PFN array with an entry indicating the source page is zero.
Use this to optimize migration to device private memory by allocating
GPU memory and zero filling it instead of failing to migrate the page.
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
