Age | Commit message (Collapse) | Author | Files | Lines |
|
By default the PMIC DA9063 2-wire interface is SMBus compliant. This
means the PMIC will automatically reset the interface when the clock
signal ceases for more than the SMBus timeout of 35 ms.
If the I2C driver / device is not capable of creating atomic I2C
transactions, a context change can cause a ceasing of the clock signal.
This can happen if for example a real-time thread is scheduled. Then
the DA9063 in SMBus mode will reset the 2-wire interface. Subsequently
a write message could end up in the wrong register. This could cause
unpredictable system behavior.
The DA9063 PMIC also supports an I2C compliant mode for the 2-wire
interface. This mode does not reset the interface when the clock
signal ceases. Thus the problem depicted above does not occur.
This patch tests for the bus functionality "I2C_FUNC_I2C". It can
reasonably be assumed that the bus cannot obey SMBus timings if
this functionality is set. SMBus commands most probably are emulated
in this case which is prone to the latency issue described above.
This patch enables the I2C bus mode if I2C_FUNC_I2C is set or
otherwise keeps the default SMBus mode.
Signed-off-by: Hubert Streidl <hubert.streidl@de.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The driver was using subsys_initcall() because in old times deferred
probe was not supported everywhere and specific ordering was needed.
Since probe deferral works fine and specific ordering is discouraged
(hides dependencies between drivers and couples their boot order), the
driver can be converted to regular module_platform_driver.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds access tables to the MAX 10 BMC regmap. This prevents
the host from accessing the unwanted I/O space. It also filters out the
invalid outputs when reading the regmap debugfs interface.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The version register is the only one in the legacy I/O space to be
accessed, so it is not necessary to define the legacy base & version
register offset. A direct definition of the legacy version register
address would be fine.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Fixes the following coccicheck warning:
drivers/mfd/lm3533-core.c:361:60-61: WARNING opportunity for kobj_to_dev()
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The sparse tool complains as follows:
drivers/mfd/ene-kb3930.c:36:15: warning: symbol 'kb3930_power_off' was not declared. Should it be static?
The symbol is not used outside of this file.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The ST-Ericsson U300 platform has been removed, so this driver is no
longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Nobody is passing the module parameter to disable the
battery management portions so just drop this parameter.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
In stmpe_devices_init(), the start and end field of these structs are
modified, so they can not be const. Add a comment to those structs that
lacked it to reduce the risk that this happens again.
This reverts commit 8d7b3a6dac4eae22c58b0853696cbd256966741b.
Fixes: 8d7b3a6dac4e ("mfd: stmpe: Constify static struct resource")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The sparse tool complains as follows:
drivers/mfd/arizona-spi.c:28:31: warning:
symbol 'reset_gpios' was not declared. Should it be static?
drivers/mfd/arizona-spi.c:29:31: warning:
symbol 'ldoena_gpios' was not declared. Should it be static?
Those symbols are not used outside of arizona-spi.c, so this
commit marks them static.
Fixes: e933836744a2 ("mfd: arizona: Add support for ACPI enumeration of WM5102 connected over SPI")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Immutable branch between MFD and Watchdog due for the v5.13 merge window
|
|
'ib-mfd-input-v5.13-1', 'ib-mfd-platform-x86-v5.13', 'ib-mfd-power-v5.13', 'ib-mfd-pwm-rtc-v5.13-1' and 'ib-regulator-list-ramp-helpers-v5.13' into ibs-for-mfd-merged
Immutable branch between MFD, Clock, GPIO, Regulator and RTC due for the v5.13 merge window
Immutable branch between MFD and Extcon due for the v5.13 merge window
Immutable branch between MFD and Input due for the v5.13 merge window
Immutable branch between MFD and Platform/x86 due for the v5.13 merge window
Immutable branch between MFD and Power due for the v5.13 merge window
Immutable branch between MFD, PWM and RTC due for the v5.13 merge window
|
|
Add core support for ROHM BD71815 Power Management IC.
The IC integrates regulators, a battery charger with a coulomb counter,
a real-time clock (RTC), clock gate and general-purpose outputs (GPO).
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Most ROHM PMIC sub-devices only use the regmap pointer from
parent device. They can obtain this by dev_get_regamap so in
most cases the MFD device does not need to allocate and populate
the driver data. Simplify drivers by removing this.
The BD70528 still needs the access to watchdog mutex so keep
rohm_regmap_dev in use on BD70528 RTC and WDG drivers for now.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The global definition of platform data for the battery
management code has no utility after the OF conversion,
move the <linux/mfd/abx500/ab8500-bm.h> to be a local
file in drivers/power/supply and stop defining the
platform data in drivers/power/supply/ab8500_bmdata.c
and broadcast to the kernel only to have it assigned
as platform data to the MFD cells and then picked back
into the same subsystem that defined it in the first
place. This kills off a layer of indirection.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The arizona jack-dection handling is being reworked so that the
codec-child-device drivers directly handle jack-detect themselves,
so it is no longer necessary to instantiate "arizona-extcon"
child-devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add initial support for the Actions Semi ATC260x PMICs which integrates
Audio Codec, Power management, Clock generation and GPIO controller
blocks.
For the moment this driver only supports Regulator, Poweroff and Onkey
functionalities for the ATC2603C and ATC2609A chip variants.
Since the PMICs can be accessed using both I2C and SPI buses, the
following driver structure has been adopted:
-----> atc260x-core.c (Implements core functionalities)
/
ATC260x --------> atc260x-i2c.c (Implements I2C interface)
\
-----> atc260x-spi.c (Implements SPI interface - TODO)
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The Netronix embedded controller is a microcontroller found in some
e-book readers designed by the original design manufacturer Netronix,
Inc. It contains RTC, battery monitoring, system power management, and
PWM functionality.
This driver implements register access and version detection.
Third-party hardware documentation is available at:
https://github.com/neuschaefer/linux/wiki/Netronix-MSP430-embedded-controller
The EC supports interrupts, but the driver doesn't make use of them so
far.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
BD9573 and BD9576 support set of "protection" interrupts for "fatal"
issues. Those lead to SOC reset as PMIC shuts the power outputs. Thus
there is no relevant IRQ handling for them.
Few "detection" interrupts were added to the BD9576 with the idea that
SOC could take some recovery-action before error gets unrecoverable.
Unfortunately the BD9576 interrupt logic was not re-evaluated. IRQs
are not designed to be properly acknowleged - and IRQ line is kept
active for whole duration of error condition (in comparison to
informing only about state change).
For above reason, do not consider missing IRQ as error.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add core support for ROHM BD9576MUF and BD9573MUF PMICs which are
mainly used to power the R-Car series processors.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Adds PMT Telemetry aggregator support for the DG1 graphics PCIe card. The
device does not have the DVSEC region in its PCI config space so hard
code the discovery table data in the driver. Also requires a fix for DG1
in the Telemetry driver for how the ACCESS_TYPE field is used.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Some products will be available that have PMT capabilities that are not
supported. Remove the warnings in this instance to avoid nuisance messages
and confusion.
Also return an error code for capabilities that are disabled by quirk to
prevent them from keeping the driver loaded if only disabled capabilities
are found.
Fixes: 4f8217d5b0ca ("mfd: Intel Platform Monitoring Technology support")
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull Simple Firmware Interface (SFI) support removal from Rafael Wysocki:
"Drop support for depercated platforms using SFI, drop the entire
support for SFI that has been long deprecated too and make some
janitorial changes on top of that (Andy Shevchenko)"
* tag 'sfi-removal-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/platform/intel-mid: Update Copyright year and drop file names
x86/platform/intel-mid: Remove unused header inclusion in intel-mid.h
x86/platform/intel-mid: Drop unused __intel_mid_cpu_chip and Co.
x86/platform/intel-mid: Get rid of intel_scu_ipc_legacy.h
x86/PCI: Describe @reg for type1_access_ok()
x86/PCI: Get rid of custom x86 model comparison
sfi: Remove framework for deprecated firmware
cpufreq: sfi-cpufreq: Remove driver for deprecated firmware
media: atomisp: Remove unused header
mfd: intel_msic: Remove driver for deprecated platform
x86/apb_timer: Remove driver for deprecated platform
x86/platform/intel-mid: Remove unused leftovers (vRTC)
x86/platform/intel-mid: Remove unused leftovers (msic)
x86/platform/intel-mid: Remove unused leftovers (msic_thermal)
x86/platform/intel-mid: Remove unused leftovers (msic_power_btn)
x86/platform/intel-mid: Remove unused leftovers (msic_gpio)
x86/platform/intel-mid: Remove unused leftovers (msic_battery)
x86/platform/intel-mid: Remove unused leftovers (msic_ocd)
x86/platform/intel-mid: Remove unused leftovers (msic_audio)
platform/x86: intel_scu_wdt: Drop mistakenly added const
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Standardise MFD_CELL_* helpers
New Drivers:
- Add support for Acer Iconia Tab A500 Embedded Controller
New Device Support:
- Add support for ROHM BD9574MWF to BD9571MWV
- Add support for Intel Alder Lake PCH-P PCI to LPSS
- Add support for Intel Alder Lake PCH-S PCI to LPSS
New Functionality:
- Support ACPI enumeration; arizona
Fix-ups:
- Managed resources; bd9571mwv
- DT additions/fix-ups; bd9571mwv, iqs62x, max8997, gateworks-gsc, ene-kb930
- Convert to SPDX; bd9571mw
- Fix return values/error handling; sunxi
- Provide SOFTDEP; arizona
- Make use of DIV_ROUND_UP; mcp-sa11x0
- Use generic APIs; arizona
- Add MAC address sysfs entries; intel-m10-bmc
- Trivial: Coding-style fix-ups; iqs62x
- Trivial: Remove superflouous code; iqs62x
- Clear-up naming conventions; iqs62x
Bug Fixes:
- Fix 'pointer from integer' error; altera-sysmgr
- Convert SGI_MFD_IOC3 from tristate to bool; Kconfig
- Fix interrupt handling; gateworks-gsc
- Extend required delay; iqs62x
- Do not use I2C polling during calibration; iqs62x
- Do no adjust clock frequency during calibration; iqs62x
- Fix use-after-free; wm831x-auxad"
* tag 'mfd-next-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (32 commits)
mfd: wm831x-auxadc: Prevent use after free in wm831x_auxadc_read_irq()
mfd: iqs62x: Do not change clock frequency during ATI
mfd: iqs62x: Do not poll during ATI
mfd: iqs62x: Increase interrupt handler return delay
mfd: iqs62x: Rename regmap_config struct
mfd: iqs62x: Remove unused bit mask
mfd: iqs62x: Remove superfluous whitespace above fallthroughs
mfd: intel-lpss: Add Intel Alder Lake PCH-S PCI IDs
mfd: intel-m10-bmc: Expose MAC address and count
mfd: Add driver for Embedded Controller found on Acer Iconia Tab A500
dt-bindings: mfd: Add ENE KB930 Embedded Controller binding
dt-bindings: mfd: gateworks-gsc: Add fan-tach mode
mfd: intel-lpss: Add Intel Alder Lake PCH-P PCI IDs
mfd: gateworks-gsc: Fix interrupt type
mfd: Standardise MFD_CELL_* helper names
mfd: mcp-sa11x0: Use DIV_ROUND_UP to calculate rw_timeout
mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell
dt-bindings: mfd: Correct the node name of the panel LED
mfd: sgi-ioc3: Turn Kconfig option into a bool
mfd: altera-sysmgr: Fix physical address storing more
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Quite an active release for driver specific updates but very little
going on at the subsystem level this time for the regulator API.
Summary:
- Overhaul of the Qualcomm LABIBB driver.
- Allow use of regulator_sync_voltage() on coupled regulators.
- Support for Action ATC260x, Mediatek DVSRC and MT6315, Qualcomm
PCM8180/c and PM8009-1 and Richtek RT4831
- Removal of the AB3100 driver"
* tag 'regulator-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (49 commits)
regulator: bd718x7, bd71828, Fix dvs voltage levels
regulator: pca9450: Add sd-vsel GPIO
regulator: pca9450: Enable system reset on WDOG_B assertion
regulator: pca9450: Add SD_VSEL GPIO for LDO5
regulator: qcom-rpmh: fix pm8009 ldo7
regulator: mt6315: Add support for MT6315 regulator
regulator: document binding for MT6315 regulator
regulator: dt-bindings: Document charger-supply for max8997
regulator: qcom-labibb: Use disable_irq_nosync from isr
regulator: pf8x00: Fix typo for PF8200 chip name
regulator: pf8x00: set ramp_delay for bucks
regulator: core: Avoid debugfs: Directory ... already present! error
regulator: pf8x00: Add suspend support
regulator: Make regulator_sync_voltage() usable by coupled regulators
regulator: s5m8767: Drop regulators OF node reference
regulator: qcom-rpmh: Add pmc8180 and pmc8180c
regulator: qcom-rpmh: Add pmc8180 and pmc8180c
regulator: s5m8767: Fix reference count leak
regulator: remove ab3100 driver
regulator: axp20x: Fix reference cout leak
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"A relatively calm release at this time, and no massive code changes
are found in the stats, while a wide range of code refactoring and
cleanup have been done.
Note that this update includes the tree-wide trivial changes for
dropping the return value from ISA remove callbacks, too.
Below lists up some highlight:
ALSA Core:
- Support for the software jack injection via debugfs
- Fixes for sync_stop PCM operations
HD-audio and USB-audio:
- A few usual HD-audio device quirks
- Updates for Tegra HD-audio
- More quirks for Pioneer and other USB-audio devices
- Stricter state checks at USB-audio disconnection
ASoC:
- Continued code refactoring, cleanup and fixes in ASoC core API
- A KUnit testsuite for the topology code
- Lots of ASoC Intel driver Realtek codec updates, quirk additions
and fixes
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers
Others:
- Drop return value from ISA driver remove callback
- Cleanup with DIV_ROUND_UP() macro
- FireWire updates, HDSP output loopback support"
* tag 'sound-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (322 commits)
ALSA: hda: intel-dsp-config: add Alder Lake support
ASoC: soc-pcm: fix hw param limits calculation for multi-DAI
ASoC: Intel: bytcr_rt5640: Add quirk for the Acer One S1002 tablet
ASoC: Intel: bytcr_rt5651: Add quirk for the Jumper EZpad 7 tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Voyo Winpad A15 tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Estar Beauty HD MID 7316R tablet
ASoC: soc-pcm: fix hwparams min/max init for dpcm
ALSA: hda/realtek: Quirk for HP Spectre x360 14 amp setup
ALSA: usb-audio: Add implicit fb quirk for BOSS GP-10
ALSA: hda: Add another CometLake-H PCI ID
ASoC: soc-pcm: add soc_pcm_hw_update_format()
ASoC: soc-pcm: add soc_pcm_hw_update_chan()
ASoC: soc-pcm: add soc_pcm_hw_update_rate()
ASoC: wm_adsp: Remove unused control callback structure
ASoC: SOF: relax ABI checks and avoid unnecessary warnings
ASoC: codecs: lpass-tx-macro: add dapm widgets and route
ASoC: codecs: lpass-tx-macro: add support for lpass tx macro
ASoC: qcom: dt-bindings: add bindings for lpass tx macro codec
ASoC: codecs: lpass-rx-macro: add iir widgets
ASoC: codecs: lpass-rx-macro: add dapm widgets and route
...
|
|
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. Commit
05f4434bc130 ("ASoC: Intel: remove mfld_machine") is also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers,
remove the support for outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The "req" struct is always added to the "wm831x->auxadc_pending" list,
but it's only removed from the list on the success path. If a failure
occurs then the "req" struct is freed but it's still on the list,
leading to a use after free.
Fixes: 78bb3688ea18 ("mfd: Support multiple active WM831x AUXADC conversions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
After a reset event, the device automatically triggers ATI at the
default core clock frequency (16 MHz). Soon afterward, the driver
loads firmware which may attempt to lower the frequency.
If this initial ATI cycle is still in progress when the frequency
is changed, however, the device incorrectly reports channels 0, 1
and 2 to be in a state of touch once ATI finally completes.
To solve this problem, wait until ATI is complete before lowering
the frequency. Because this particular ATI cycle occurs following
a reset event, its duration is predictable and a simple delay can
suffice.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
After loading firmware, the driver triggers ATI (calibration) with
the newly loaded register configuration in place. Next, the driver
polls a register field to ensure ATI completed in a timely fashion
and that the device is ready to sense.
However, communicating with the device over I2C while ATI is under-
way may induce noise in the device and cause ATI to fail. As such,
the vendor recommends not to poll the device during ATI.
To solve this problem, let the device naturally signal to the host
that ATI is complete by way of an interrupt. A completion prevents
the sub-devices from being registered until this happens.
The former logic that scaled ATI timeout and filter settling delay
is not carried forward with the new implementation, as it produces
overly conservative delays at lower clock rates. Instead, a single
pair of delays that covers all cases is used.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The time the device takes to deassert its RDY output following an
I2C stop condition scales with the core clock frequency.
To prevent level-triggered interrupts from being reasserted after
the interrupt handler returns, increase the time before returning
to account for the worst-case delay (~90 us) plus margin.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The regmap member of the driver's private data is called 'regmap',
but the regmap_config struct is called 'iqs62x_map_config'. Rename
the latter to 'iqs62x_regmap_config' for consistency.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The register write that performed a mandatory soft reset during
probe was removed during development of the driver, however the
IQS62X_SYS_SETTINGS_SOFT_RESET bit mask was left behind. Remove
it to keep stray macros out of the driver.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Previously, all instances of the /* fall through */ comment were
preceded by a newline to improve readability.
Now that /* fall through */ comments have been replaced with the
fallthrough pseudo-keyword, the leftover whitespace looks out of
place and can simply be removed.
Fixes: df561f6688fe ("treewide: Use fallthrough pseudo-keyword")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add Intel Alder Lake LPSS PCI IDs.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Create two sysfs entries for exposing the MAC address and count
from the MAX10 BMC register space. The MAC address is the first
in a sequential block of MAC addresses reserved for the FPGA card.
The MAC count is the number of MAC addresses in the reserved block.
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Acer Iconia Tab A500 is an Android tablet device, it has ENE KB930
Embedded Controller which provides battery-gauge, LED, GPIO and some
other functions. The EC uses firmware that is specifically customized
for Acer A500. This patch adds MFD driver for the Embedded Controller
which allows to power-off / reboot the A500 device, it also provides
a common register read/write API that will be used by the sub-devices.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add Intel Alder Lake LPSS PCI IDs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The Gateworks System Controller has an active-low interrupt.
Fix the interrupt request type.
Cc: <stable@vger.kernel.org>
Fixes: d85234994b2f ("mfd: Add Gateworks System Controller core driver")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Start all helpers with "MFD_CELL_".
Cc: Gene Chen <gene_chen@richtek.com>
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Don't open-code DIV_ROUND_UP() kernel macro.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add of_compatible ("maxim,max8997-muic") to the mfd_cell to have a
of_node set in the extcon driver.
Add of_compatible ("maxim,max8997-battery") to the mfd_cell to configure
the charger driver.
Signed-off-by: Timon Baetz <timon.baetz@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Module builds of ioc3 fail with following errors:
ERROR: "spurious_interrupt" [drivers/mfd/ioc3.ko] undefined!
ERROR: "pci_find_host_bridge" [drivers/mfd/ioc3.ko] undefined!
Exporting pci_find_host_bridge got rejected by maintainer, so easiest
fix is to disable module building, which even makes sense since both
SGI Origin and Octane always contain at least one IOC3 chip.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
A recent fix improved the way the resource gets passed to
the low-level accessors, but left one warning that appears
in configurations with a resource_size_t that is wider than
a pointer:
In file included from drivers/mfd/altera-sysmgr.c:19:
drivers/mfd/altera-sysmgr.c: In function 'sysmgr_probe':
drivers/mfd/altera-sysmgr.c:148:40: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
148 | regmap = devm_regmap_init(dev, NULL, (void *)res->start,
| ^
include/linux/regmap.h:646:6: note: in definition of macro '__regmap_lockdep_wrapper'
646 | fn(__VA_ARGS__, &_key, \
| ^~~~~~~~~~~
drivers/mfd/altera-sysmgr.c:148:12: note: in expansion of macro 'devm_regmap_init'
148 | regmap = devm_regmap_init(dev, NULL, (void *)res->start,
| ^~~~~~~~~~~~~~~~
I had tried a different approach that would store the address
in the private data as a phys_addr_t, but the easiest solution
now seems to be to add a double cast to shut up the warning.
As the address is passed to an inline assembly, it is guaranteed
to not be wider than a register anyway.
Fixes: d9ca7801b6e5 ("mfd: altera-sysmgr: Fix physical address storing hacks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
'ib-mfd-gpio-regulator-5.12' into ibs-for-mfd-merged
|
|
The Intel Bay Trail (x86/ACPI) based Lenovo Yoga Tablet 2 series use
a WM5102 codec connected over SPI.
Add support for ACPI enumeration to arizona-spi so that arizona-spi can
bind to the codec on these tablets.
This is loosely based on an earlier attempt (for Android-x86) at this by
Christian Hartmann, combined with insights in things like the speaker GPIO
from the android-x86 android port for the Lenovo Yoga Tablet 2 1051F/L [1].
[1] https://github.com/Kitsune2222/Android_Yoga_Tablet_2-1051F_Kernel
Cc: Christian Hartmann <cornogle@googlemail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Replace the custom arizona_of_get_type() function with the generic
device_get_match_data() helper. Besides being a nice cleanup this
also makes it easier to add support for binding to ACPI enumerated
devices.
While at it also fix a possible NULL pointer deref of the id
argument to the probe functions (this could happen on e.g. manual
driver binding through sysfs).
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The (shared) probing code of the arizona-i2c and arizona-spi modules
takes the following steps during init:
1. Call mfd_add_devices() for a set of early child-devices, this
includes the arizona_ldo1 device which provides one of the
core-regulators.
2. Bulk enable the core-regulators.
3. Read the device id.
4. Call mfd_add_devices() for the other child-devices.
This sequence depends on 1. leading to not only the child-device
being created, but also the driver for the child-device binding
to it and registering its regulator.
This requires the arizona_ldo1 driver to be loaded before the
shared probing code runs. Add a softdep for this to both modules to
ensure that this requirement is met.
Note this mirrors the existing MODULE_SOFTDEP("pre: wm8994_regulator")
in the wm8994 code, which has a similar init sequence.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. To simplify the quest to
make this function return void, let struct sunxi_rsb_driver::remove
return void, too. All users already unconditionally return 0, this
commit makes this obvious and ensures future users don't behave
differently. To simplify even further, make axp20x_device_remove()
return void instead of returning 0 unconditionally, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The new PMIC BD9574MWF inherits features from BD9571MWV.
Add the support of new PMIC to existing bd9571mwv driver.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Co-developed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|