summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h
AgeCommit message (Collapse)AuthorFilesLines
2019-11-16bnx2x: Remove format_fw_ver_t function castsKees Cook1-1/+1
The return values for format_fw_ver_t callbacks are supposed to be "int", not "u8". Ultimately, the top-level caller doesn't actually check the return value at all, but just clean this all up anyway and fix the prototypes so that casts are no longer needed. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-16bnx2x: Remove config_init_t function castsKees Cook1-2/+2
No callers of .config_init check return values. Remove the casting and change all callbacks to have the correct function prototype. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-18bnx2x: Check if transceiver implements DDM before accessMauro S. M. Rodrigues1-0/+1
Some transceivers may comply with SFF-8472 even though they do not implement the Digital Diagnostic Monitoring (DDM) interface described in the spec. The existence of such area is specified by the 6th bit of byte 92, set to 1 if implemented. Currently, without checking this bit, bnx2x fails trying to read sfp module's EEPROM with the follow message: ethtool -m enP5p1s0f1 Cannot get Module EEPROM data: Input/output error Because it fails to read the additional 256 bytes in which it is assumed to exist the DDM data. This issue was noticed using a Mellanox Passive DAC PN 01FT738. The EEPROM data was confirmed by Mellanox as correct and similar to other Passive DACs from other manufacturers. Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com> Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-22bnx2x: Rebrand from 'broadcom' into 'qlogic'Yuval Mintz1-4/+6
bnx2x still appears as a Broadcom driver even though the devices it utilizes belong to Qlogic for more than a year. This patch changes the various headers and the device strings to indicate the correct ownership of the device. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-06bnx2x: Fix link problems for 1G SFP RJ45 moduleYaniv Rosner1-2/+3
When 1G SFP RJ45 module is detected, driver must reset the Tx laser in order to prevent link issues. As part of change, the link_attr_sync was relocated from vars to params. Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-13bnx2x: namespace and dead code cleanupsstephen hemminger1-9/+1
Fix a bunch of whole lot of namespace issues with the Broadcom bnx2x driver found by running 'make namespacecheck' * global variables must be prefixed with bnx2x_ naming a variable int_mode, or num_queue is invitation to disaster * make local functions static * move some inline's used in one file out of header (this driver has a bad case of inline-itis) * remove resulting dead code fallout bnx2x_pfc_statistic, bnx2x_emac_get_pfc_stat bnx2x_init_vlan_mac_obj, Looks like vlan mac support in this driver was a botch from day one either never worked, or not implemented or missing support functions Compile tested only. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-27bnx2x: Support reading I2C EEPROM SFF8472Yaniv Rosner1-2/+14
Add full support for "ethtool -m" command. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-08bnx2x: Fix SFP+ misconfiguration in iSCSI boot scenarioYaniv Rosner1-0/+1
Fix a problem in which iSCSI-boot installation fails when switching SFP+ boot port and moving the SFP+ module prior to boot. The SFP+ insertion triggers an interrupt which configures the SFP+ module wrongly before interface is loaded. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-08bnx2x: Fix intermittent long KR2 link up timeYaniv Rosner1-1/+2
When a KR2 device is connected to a KR link-partner, sometimes it requires disabling KR2 for the link to come up. To get a KR2 link up later, in case no base pages are seen, the KR2 is restored. The problem was that some link partners cleared their advertised BP/NP after around two seconds, causing the driver to disable/enable KR2 link all the time. The fix was to wait at least 5 seconds before checking KR2 recovery. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-01bnx2x: Fix port identification for the 84834Yaniv Rosner1-1/+2
Fix the "ethtool -p" for boards with BCM84834, by using LED4 of the PHY to toggle the link LED while keeping interrupt disabled to avoid NIG attentions, and at the end restore NIG to previous state. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-16bnx2x: Introduce 2013 and advance version to 1.78.02Yuval Mintz1-1/+1
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-12-07bnx2x: Prevent link flaps when booting from SAN.Barak Witkowski1-0/+1
It is possible that the driver is configured to operate with a certain link configuration which differs from the link's configuration during boot from SAN - this would cause the driver to flap the link. Said flap may be missed by specific switches, causing dcbx convergence to be too long and boot sequence to fail. Convergence is longer because switch ignores new dcbx packets due to counters mismatch, as only host side reset the counters due to the link flap. This patch causes the driver to ignore user's initial configuration during boot from SAN, and continues with the existing link configuration. Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-28bnx2x: Cosmetic changesYaniv Rosner1-4/+1
This patch makes some cosmetic changes to the code: 1. Code alignment. 2. Merge read-modify-write into a single function (read_or_write / read_and_write). 3. Merge several write registers into a for-loop write using a static array. 4. Remove empty lines. 5. Fix comments. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-28bnx2x: Always take PHY lockYaniv Rosner1-6/+0
Taking PHY lock is not required on some older designs, but we are removing this complication and always taking it since it is always required on newer designs and does not worth the code complication on the older boards. Taking PHY lock was initially required only on specific boards which had their MDC/MDIO bus crossed, but since this lock is now always required, for example, when NCSI is present, the PHY lock will always be taken. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-28bnx2x: Change MDIO clock settingsYaniv Rosner1-0/+3
When drivers works on top of an old bootcode, it is theoretically subjected to MDC/MDIO failures since the MDIO clock is set in the beginning of each sequence, rather than per CL45 command. On rare cases an old bootcodes may change that in the middle, so to address that, the MDIO clock is set for each CL45 access. In addition, setting the MDIO clock is now done per EMAC base, and not per port number, since a specific port can potentially use both EMACs for different PHY accesses. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-28bnx2x: Add support for 20G-KR2Yaniv Rosner1-0/+2
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-08bnx2x: Support loading cnic resources at run-timeMerav Sicron1-1/+2
This patch replaces the BCM_CNIC define with a flag which can change at run-time and which does not use the CONFIG_CNIC kconfig option. For the PF/hypervisor driver cnic is always supported, however allocation of cnic resources and configuration of the HW for offload mode is done only when the cnic module registers bnx2x. Signed-off-by: Merav Sicron <meravs@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-13bnx2x: Utilize Link Flap AvoidanceYuval Mintz1-1/+1
Change various flows in the bnx2x driver which up until now flapped the link - these flows now benefit from the link flap avoidance mechanism. This includes the removal of the link reset made upon nic init, as it is possible the link is already active at that time. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-13bnx2x: Link Flap AvoidanceYaniv Rosner1-0/+2
Various flows in the bnx2x driver cause a link-flap - if the link is up, it would be toggled down (after a mac/phy reset) and then taken back up. In many of these cases, there is no need to do cause such a flap, as the associated flows should not actually affect the link. This patch adds the 'Link Flap Avoidance' mechanism, which allows the driver to better determine if a given flow requires a link change, and thus minimize the number of link flaps caused by the driver. Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-13bnx2x: link code refactoringYaniv Rosner1-0/+1
Separate the interrupt setting part of each external PHY to a specific function. This allows calling the interrupt setting in case of link-flap avoidance, since some link owners may not enable the interrupt on their own. Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-11bnx2x: use native EEE instead of auto-greeenYuval Mintz1-0/+1
This patch enables boards with 54618SE phys and a sufficiently new firmware to use native EEE instead of auto-greeen. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-11bnx2x: correct & clean 10G EEE requirementsYuval Mintz1-1/+0
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-11drivers/net/ethernet: Fix non-kernel-doc comments with kernel-doc start markersBen Hutchings1-2/+1
Convert doxygen (or similar) formatted comments to kernel-doc or unformatted comment. Delete a few that are content-free. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-23bnx2x: link module eepromYuval Mintz1-0/+1
Add the ethtool functionality of accessing optic modules' information and eeprom to the bnx2x driver. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-23bnx2x: 1G sfp+ module handlingYuval Mintz1-8/+9
Automatically lower requested link speed to 1G in case 1G SFP+ module is detected. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-23bnx2x: revised link register accessYuval Mintz1-0/+5
This is a semantic change, cleaning some sections in which the bnx2x handles the phy's registers. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-23bnx2x: sfp+ Tx fault detection addedYuval Mintz1-0/+1
Adds the ability to identify sfp+ modules' Tx fault, and when such occur shut down the link. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-08bnx2x: Added EEE supportYuval Mintz1-0/+26
This patch adds energy efficient energy support (802.3az) to bnx2x boards with 84833 phys (and sufficiently new BC and external FW). Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-24bnx2x: add afex supportBarak Witkowski1-0/+1
Following patch adds afex multifunction support to the driver (afex multifunction is based on vntag header) and updates FW version used to 7.2.51. Support includes the following: 1. Configure vif parameters in firmware (default vlan, vif id, default priority, allowed priorities) according to values received from NIC. 2. Configure FW to strip/add default vlan according to afex vlan mode. 3. Notify link up to OS only after vif is fully initialized. 4. Support vif list set/get requests and configure FW accordingly. 5. Supply afex statistics upon request from NIC. 6. Special handling to L2 interface in case of FCoE vif. Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-04bnx2x: Add remote-fault link detectionYaniv Rosner1-0/+3
Restore remote-faule detection, which periodically checks for remote-fault on the MAC layer. In case physical link appear to be up but fault is set, it will provide a link down indication, and when the fault is cleared, it will indicate link up again. Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-28bnx2x: previous driver unload revisedYuval Mintz1-0/+2
The flow in which the bnx2x driver starts after a previous driver has been terminated in an 'unclean' manner has several bugs and FW risks, which makes it possible for the driver to fail after boot-from-SAN or kdump. This patch contains a revised flow which performs a safer initialization, solving the possible crash scenarios. Notice this patch contains lines with over 80 characters, as it keeps print-strings in a single line. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-16bnx2x: allow all functions to display the phy FW versionMintz Yuval1-2/+2
The phy FW version is stored in regular memory, no MDC-MDIO access or any special locks are required to read it in the current implementation. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26bnx2x: Update version to 1.72.0 and copyrightsAriel Elior1-1/+1
Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-29bnx2x: ETS changesYaniv Rosner1-1/+1
Fix a problem when new traffic class is created with 0% BW, the ETS is not conforming. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28bnx2x: Add link retry to 578xx-KRYaniv Rosner1-0/+3
This fix solves a problem of no link on 578xx-KR by retrying to link up to four timer using the periodic function. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-11broadcom: Move the Broadcom driversJeff Kirsher1-0/+493
Moves the drivers for Broadcom devices into drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile changes. CC: Eilon Greenstein <eilong@broadcom.com> CC: Michael Chan <mchan@broadcom.com> CC: Matt Carlson <mcarlson@broadcom.com> CC: Gary Zambrano <zambrano@broadcom.com> CC: "Maciej W. Rozycki" <macro@linux-mips.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-08-16 12:06:24 +0300