summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/mellanox/mlxsw
AgeCommit message (Collapse)AuthorFilesLines
2022-04-20mlxsw: i2c: Fix initialization error flowVadim Pasternak1-0/+1
[ Upstream commit d452088cdfd5a4ad9d96d847d2273fe958d6339b ] Add mutex_destroy() call in driver initialization error flow. Fixes: 6882b0aee180f ("mlxsw: Introduce support for I2C bus") Signed-off-by: Vadim Pasternak <vadimp@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Link: https://lore.kernel.org/r/20220407070703.2421076-1-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27mlxsw: pci: Avoid flow control for EMAD packetsDanielle Ratson2-1/+17
[ Upstream commit d43e4271747ace01a27a49a97a397cb4219f6487 ] Locally generated packets ingress the device through its CPU port. When the CPU port is congested and there are not enough credits in its headroom buffer, packets can be dropped. While this might be acceptable for data packets that traverse the network, configuration packets exchanged between the host and the device (EMADs) should not be subjected to this flow control. The "sdq_lp" bit in the SDQ (Send Descriptor Queue) context allows the host to instruct the device to treat packets sent on this queue as "local processing" and always process them, regardless of the state of the CPU port's headroom. Add the definition of this bit and set it for the dedicated SDQ reserved for the transmission of EMAD packets. This makes the "local processing" bit in the WQE (Work Queue Element) redundant, so clear it. Signed-off-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27mlxsw: pci: Add shutdown method in PCI driverDanielle Ratson1-0/+1
[ Upstream commit c1020d3cf4752f61a6a413f632ea2ce2370e150d ] On an arm64 platform with the Spectrum ASIC, after loading and executing a new kernel via kexec, the following trace [1] is observed. This seems to be caused by the fact that the device is not properly shutdown before executing the new kernel. Fix this by implementing a shutdown method which mirrors the remove method, as recommended by the kexec maintainer [2][3]. [1] BUG: Bad page state in process devlink pfn:22f73d page:fffffe00089dcf40 refcount:-1 mapcount:0 mapping:0000000000000000 index:0x0 flags: 0x2ffff00000000000() raw: 2ffff00000000000 0000000000000000 ffffffff089d0201 0000000000000000 raw: 0000000000000000 0000000000000000 ffffffffffffffff 0000000000000000 page dumped because: nonzero _refcount Modules linked in: CPU: 1 PID: 16346 Comm: devlink Tainted: G B 5.8.0-rc6-custom-273020-gac6b365b1bf5 #44 Hardware name: Marvell Armada 7040 TX4810M (DT) Call trace: dump_backtrace+0x0/0x1d0 show_stack+0x1c/0x28 dump_stack+0xbc/0x118 bad_page+0xcc/0xf8 check_free_page_bad+0x80/0x88 __free_pages_ok+0x3f8/0x418 __free_pages+0x38/0x60 kmem_freepages+0x200/0x2a8 slab_destroy+0x28/0x68 slabs_destroy+0x60/0x90 ___cache_free+0x1b4/0x358 kfree+0xc0/0x1d0 skb_free_head+0x2c/0x38 skb_release_data+0x110/0x1a0 skb_release_all+0x2c/0x38 consume_skb+0x38/0x130 __dev_kfree_skb_any+0x44/0x50 mlxsw_pci_rdq_fini+0x8c/0xb0 mlxsw_pci_queue_fini.isra.0+0x28/0x58 mlxsw_pci_queue_group_fini+0x58/0x88 mlxsw_pci_aqs_fini+0x2c/0x60 mlxsw_pci_fini+0x34/0x50 mlxsw_core_bus_device_unregister+0x104/0x1d0 mlxsw_devlink_core_bus_device_reload_down+0x2c/0x48 devlink_reload+0x44/0x158 devlink_nl_cmd_reload+0x270/0x290 genl_rcv_msg+0x188/0x2f0 netlink_rcv_skb+0x5c/0x118 genl_rcv+0x3c/0x50 netlink_unicast+0x1bc/0x278 netlink_sendmsg+0x194/0x390 __sys_sendto+0xe0/0x158 __arm64_sys_sendto+0x2c/0x38 el0_svc_common.constprop.0+0x70/0x168 do_el0_svc+0x28/0x88 el0_sync_handler+0x88/0x190 el0_sync+0x140/0x180 [2] https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1195432.html [3] https://patchwork.kernel.org/project/linux-scsi/patch/20170212214920.28866-1-anton@ozlabs.org/#20116693 Cc: Eric Biederman <ebiederm@xmission.com> Signed-off-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-12-01mlxsw: spectrum: Protect driver from buggy firmwareAmit Cohen1-1/+1
[ Upstream commit 63b08b1f6834bbb0b4f7783bf63b80c8c8e9a047 ] When processing port up/down events generated by the device's firmware, the driver protects itself from events reported for non-existent local ports, but not the CPU port (local port 0), which exists, but lacks a netdev. This can result in a NULL pointer dereference when calling netif_carrier_{on,off}(). Fix this by bailing early when processing an event reported for the CPU port. Problem was only observed when running on top of a buggy emulator. Fixes: 28b1987ef506 ("mlxsw: spectrum: Register CPU port with devlink") Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-26mlxsw: pci: Recycle received packet upon allocation failureIdo Schimmel1-13/+12
When the driver fails to allocate a new Rx buffer, it passes an empty Rx descriptor (contains zero address and size) to the device and marks it as invalid by setting the skb pointer in the descriptor's metadata to NULL. After processing enough Rx descriptors, the driver will try to process the invalid descriptor, but will return immediately seeing that the skb pointer is NULL. Since the driver no longer passes new Rx descriptors to the device, the Rx queue will eventually become full and the device will start to drop packets. Fix this by recycling the received packet if allocation of the new packet failed. This means that allocation is no longer performed at the end of the Rx routine, but at the start, before tearing down the DMA mapping of the received packet. Remove the comment about the descriptor being zeroed as it is no longer correct. This is OK because we either use the descriptor as-is (when recycling) or overwrite its address and size fields with that of the newly allocated Rx buffer. The issue was discovered when a process ("perf") consumed too much memory and put the system under memory pressure. It can be reproduced by injecting slab allocation failures [1]. After the fix, the Rx queue no longer comes to a halt. [1] # echo 10 > /sys/kernel/debug/failslab/times # echo 1000 > /sys/kernel/debug/failslab/interval # echo 100 > /sys/kernel/debug/failslab/probability FAULT_INJECTION: forcing a failure. name failslab, interval 1000, probability 100, space 0, times 8 [...] Call Trace: <IRQ> dump_stack_lvl+0x34/0x44 should_fail.cold+0x32/0x37 should_failslab+0x5/0x10 kmem_cache_alloc_node+0x23/0x190 __alloc_skb+0x1f9/0x280 __netdev_alloc_skb+0x3a/0x150 mlxsw_pci_rdq_skb_alloc+0x24/0x90 mlxsw_pci_cq_tasklet+0x3dc/0x1200 tasklet_action_common.constprop.0+0x9f/0x100 __do_softirq+0xb5/0x252 irq_exit_rcu+0x7a/0xa0 common_interrupt+0x83/0xa0 </IRQ> asm_common_interrupt+0x1e/0x40 RIP: 0010:cpuidle_enter_state+0xc8/0x340 [...] mlxsw_spectrum2 0000:06:00.0: Failed to alloc skb for RDQ Fixes: eda6500a987a ("mlxsw: Add PCI bus implementation") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Link: https://lore.kernel.org/r/20211024064014.1060919-1-idosch@idosch.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-14mlxsw: thermal: Fix out-of-bounds memory accessesIdo Schimmel1-47/+5
Currently, mlxsw allows cooling states to be set above the maximum cooling state supported by the driver: # cat /sys/class/thermal/thermal_zone2/cdev0/type mlxsw_fan # cat /sys/class/thermal/thermal_zone2/cdev0/max_state 10 # echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state # echo $? 0 This results in out-of-bounds memory accesses when thermal state transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the transition table is accessed with a too large index (state) [1]. According to the thermal maintainer, it is the responsibility of the driver to reject such operations [2]. Therefore, return an error when the state to be set exceeds the maximum cooling state supported by the driver. To avoid dead code, as suggested by the thermal maintainer [3], partially revert commit a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels") that tried to interpret these invalid cooling states (above the maximum) in a special way. The cooling levels array is not removed in order to prevent the fans going below 20% PWM, which would cause them to get stuck at 0% PWM. [1] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290 Read of size 4 at addr ffff8881052f7bf8 by task kworker/0:0/5 CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.15.0-rc3-custom-45935-gce1adf704b14 #122 Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016 Workqueue: events_freezable_power_ thermal_zone_device_check Call Trace: dump_stack_lvl+0x8b/0xb3 print_address_description.constprop.0+0x1f/0x140 kasan_report.cold+0x7f/0x11b thermal_cooling_device_stats_update+0x271/0x290 __thermal_cdev_update+0x15e/0x4e0 thermal_cdev_update+0x9f/0xe0 step_wise_throttle+0x770/0xee0 thermal_zone_device_update+0x3f6/0xdf0 process_one_work+0xa42/0x1770 worker_thread+0x62f/0x13e0 kthread+0x3ee/0x4e0 ret_from_fork+0x1f/0x30 Allocated by task 1: kasan_save_stack+0x1b/0x40 __kasan_kmalloc+0x7c/0x90 thermal_cooling_device_setup_sysfs+0x153/0x2c0 __thermal_cooling_device_register.part.0+0x25b/0x9c0 thermal_cooling_device_register+0xb3/0x100 mlxsw_thermal_init+0x5c5/0x7e0 __mlxsw_core_bus_device_register+0xcb3/0x19c0 mlxsw_core_bus_device_register+0x56/0xb0 mlxsw_pci_probe+0x54f/0x710 local_pci_probe+0xc6/0x170 pci_device_probe+0x2b2/0x4d0 really_probe+0x293/0xd10 __driver_probe_device+0x2af/0x440 driver_probe_device+0x51/0x1e0 __driver_attach+0x21b/0x530 bus_for_each_dev+0x14c/0x1d0 bus_add_driver+0x3ac/0x650 driver_register+0x241/0x3d0 mlxsw_sp_module_init+0xa2/0x174 do_one_initcall+0xee/0x5f0 kernel_init_freeable+0x45a/0x4de kernel_init+0x1f/0x210 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff8881052f7800 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 1016 bytes inside of 1024-byte region [ffff8881052f7800, ffff8881052f7c00) The buggy address belongs to the page: page:0000000052355272 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1052f0 head:0000000052355272 order:3 compound_mapcount:0 compound_pincount:0 flags: 0x200000000010200(slab|head|node=0|zone=2) raw: 0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0 raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [2] https://lore.kernel.org/linux-pm/9aca37cb-1629-5c67-1895-1fdc45c0244e@linaro.org/ [3] https://lore.kernel.org/linux-pm/af9857f2-578e-de3a-e62b-6baff7e69fd4@linaro.org/ CC: Daniel Lezcano <daniel.lezcano@linaro.org> Fixes: a50c1e35650b ("mlxsw: core: Implement thermal zone") Fixes: a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Vadim Pasternak <vadimp@nvidia.com> Link: https://lore.kernel.org/r/20211012174955.472928-1-idosch@idosch.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-22mlxsw: spectrum_router: Increase parsing depth for multipath hashAmit Cohen2-1/+44
Commit 01848e05f8bb ("mlxsw: spectrum_router: Add support for inner layer 3 multipath hash policy") and commit daeabf89eb89 ("mlxsw: spectrum_router: Add support for custom multipath hash policy") added support for multipath hash policies where the hash is calculated based on inner packet fields. For IPv6-in-IPv6 packets, the default parsing depth (96 bytes) is not enough when these policies are used. Therefore, for such cases, call the new API to increase / decrease the parsing depth as necessary. Care is taken to ensure the API is not called multiple times. Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-22mlxsw: Remove old parsing depth infrastructureAmit Cohen2-69/+0
The previous patches added new API to handle parsing depth and converted the existing code to use it. Remove the old infrastructure which is not needed anymore. Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-22mlxsw: Convert existing consumers to use new API for parsing configurationAmit Cohen2-8/+22
Convert VxLAN and PTP modules to increase parsing depth using new API that was added in the previous patch. Separate MPRS register's configuration to VxLAN related configuration and parsing depth configuration. Handle each one using the appropriate API. Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-22mlxsw: spectrum: Add infrastructure for parsing configurationAmit Cohen2-0/+94
Spectrum ASICs have a configurable limit on how deep into the packet they parse. By default, the limit is 96 bytes. There are several cases where this parsing depth is not enough and there is a need to increase it. Currently, increasing parsing depth is maintained as part of VxLAN module, because the MPRS register which configures parsing depth also configures UDP destination port number used for VxLAN encapsulation and decapsulation. Add an API for increasing parsing depth as part of spectrum.c code, so that it will be possible to use it from other modules. In addition, add an API for setting UDP destination port and protect it using a dedicated lock for saving parsing configurations. The lock is needed as not all the callers hold RTNL lock. Maintain a counter for increased parsing depth consumers. For first consumer subscription, increase the parsing depth and for last consumer unsubscription, set parsing depth to default value. Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-14ethernet: fix PTP_1588_CLOCK dependenciesArnd Bergmann1-1/+1
The 'imply' keyword does not do what most people think it does, it only politely asks Kconfig to turn on another symbol, but does not prevent it from being disabled manually or built as a loadable module when the user is built-in. In the ICE driver, the latter now causes a link failure: aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl': ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config' ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config' aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config' ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config' aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset': ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release' ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release' aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild': This is a recurring problem in many drivers, and we have discussed it several times befores, without reaching a consensus. I'm providing a link to the previous email thread for reference, which discusses some related problems. To solve the dependency issue better than the 'imply' keyword, introduce a separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver can depend on if it is able to use PTP support when available, but works fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are then prevented from being built-in, the same way as with a 'depends on PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick, but that can be rather confusing when you first see it. Since this should cover the dependencies correctly, the IS_REACHABLE() hack in the header is no longer needed now, and can be turned back into a normal IS_ENABLED() check. Any driver that gets the dependency wrong will now cause a link time failure rather than being unable to use PTP support when that is in a loadable module. However, the two recently added ptp_get_vclocks_index() and ptp_convert_timestamp() interfaces are only called from builtin code with ethtool and socket timestamps, so keep the current behavior by stubbing those out completely when PTP is in a loadable module. This should be addressed properly in a follow-up. As Richard suggested, we may want to actually turn PTP support into a 'bool' option later on, preventing it from being a loadable module altogether, which would be one way to solve the problem with the ethtool interface. Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices") Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/ Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/ Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/ Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/ Acked-by: Shannon Nelson <snelson@pensando.io> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2-3/+3
Conflicts: drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h 9e26680733d5 ("bnxt_en: Update firmware call to retrieve TX PTP timestamp") 9e518f25802c ("bnxt_en: 1PPS functions to configure TSIO pins") 099fdeda659d ("bnxt_en: Event handler for PPS events") kernel/bpf/helpers.c include/linux/bpf-cgroup.h a2baf4e8bb0f ("bpf: Fix potentially incorrect results with bpf_get_local_storage()") c7603cfa04e7 ("bpf: Add ambient BPF runtime context stored in current") drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c 5957cc557dc5 ("net/mlx5: Set all field of mlx5_irq before inserting it to the xarray") 2d0b41a37679 ("net/mlx5: Refcount mlx5_irq with integer") MAINTAINERS 7b637cd52f02 ("MAINTAINERS: fix Microchip CAN BUS Analyzer Tool entry typo") 7d901a1e878a ("net: phy: add Maxlinear GPY115/21x/24x driver") Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-10net: switchdev: zero-initialize struct switchdev_notifier_fdb_info emitted ↵Vladimir Oltean2-3/+3
by drivers towards the bridge The blamed commit added a new field to struct switchdev_notifier_fdb_info, but did not make sure that all call paths set it to something valid. For example, a switchdev driver may emit a SWITCHDEV_FDB_ADD_TO_BRIDGE notifier, and since the 'is_local' flag is not set, it contains junk from the stack, so the bridge might interpret those notifications as being for local FDB entries when that was not intended. To avoid that now and in the future, zero-initialize all switchdev_notifier_fdb_info structures created by drivers such that all newly added fields to not need to touch drivers again. Fixes: 2c4eca3ef716 ("net: bridge: switchdev: include local flag in FDB notifications") Reported-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Karsten Graul <kgraul@linux.ibm.com> Link: https://lore.kernel.org/r/20210810115024.1629983-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-09devlink: Set device as early as possibleLeon Romanovsky1-2/+3
All kernel devlink implementations call to devlink_alloc() during initialization routine for specific device which is used later as a parent device for devlink_register(). Such late device assignment causes to the situation which requires us to call to device_register() before setting other parameters, but that call opens devlink to the world and makes accessible for the netlink users. Any attempt to move devlink_register() to be the last call generates the following error due to access to the devlink->dev pointer. [ 8.758862] devlink_nl_param_fill+0x2e8/0xe50 [ 8.760305] devlink_param_notify+0x6d/0x180 [ 8.760435] __devlink_params_register+0x2f1/0x670 [ 8.760558] devlink_params_register+0x1e/0x20 The simple change of API to set devlink device in the devlink_alloc() instead of devlink_register() fixes all this above and ensures that prior to call to devlink_register() everything already set. Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27dev_ioctl: split out ndo_eth_ioctlArnd Bergmann1-1/+1
Most users of ndo_do_ioctl are ethernet drivers that implement the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP. Separate these from the few drivers that use ndo_do_ioctl to implement SIOCBOND, SIOCBR and SIOCWANDEV commands. This is a purely cosmetic change intended to help readers find their way through the implementation. Cc: Doug Ledford <dledford@redhat.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Vladimir Oltean <olteanv@gmail.com> Cc: Leon Romanovsky <leon@kernel.org> Cc: linux-rdma@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23net: bridge: switchdev: allow the TX data plane forwarding to be offloadedTobias Waldekranz1-1/+1
Allow switchdevs to forward frames from the CPU in accordance with the bridge configuration in the same way as is done between bridge ports. This means that the bridge will only send a single skb towards one of the ports under the switchdev's control, and expects the driver to deliver the packet to all eligible ports in its domain. Primarily this improves the performance of multicast flows with multiple subscribers, as it allows the hardware to perform the frame replication. The basic flow between the driver and the bridge is as follows: - When joining a bridge port, the switchdev driver calls switchdev_bridge_port_offload() with tx_fwd_offload = true. - The bridge sends offloadable skbs to one of the ports under the switchdev's control using skb->offload_fwd_mark = true. - The switchdev driver checks the skb->offload_fwd_mark field and lets its FDB lookup select the destination port mask for this packet. v1->v2: - convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long - introduce a static key "br_switchdev_fwd_offload_used" to minimize the impact of the newly introduced feature on all the setups which don't have hardware that can make use of it - introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache line access - reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in __br_forward() - do not strip VLAN on egress if forwarding offload on VLAN-aware bridge is being used - propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP v2->v3: - replace the solution based on .ndo_dfwd_add_station with a solution based on switchdev_bridge_port_offload - rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD v3->v4: rebase v4->v5: - make sure the static key is decremented on bridge port unoffload - more function and variable renaming and comments for them: br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload fwd_accel to tx_fwd_offload Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22net: bridge: move the switchdev object replay helpers to "push" modeVladimir Oltean1-2/+2
Starting with commit 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries"), DSA has introduced some bridge helpers that replay switchdev events (FDB/MDB/VLAN additions and deletions) that can be lost by the switchdev drivers in a variety of circumstances: - an IP multicast group was host-joined on the bridge itself before any switchdev port joined the bridge, leading to the host MDB entries missing in the hardware database. - during the bridge creation process, the MAC address of the bridge was added to the FDB as an entry pointing towards the bridge device itself, but with no switchdev ports being part of the bridge yet, this local FDB entry would remain unknown to the switchdev hardware database. - a VLAN/FDB/MDB was added to a bridge port that is a LAG interface, before any switchdev port joined that LAG, leading to the hardware database missing those entries. - a switchdev port left a LAG that is a bridge port, while the LAG remained part of the bridge, and all FDB/MDB/VLAN entries remained installed in the hardware database of the switchdev port. Also, since commit 0d2cfbd41c4a ("net: bridge: ignore switchdev events for LAG ports which didn't request replay"), DSA introduced a method, based on a const void *ctx, to ensure that two switchdev ports under the same LAG that is a bridge port do not see the same MDB/VLAN entry being replayed twice by the bridge, once for every bridge port that joins the LAG. With so many ordering corner cases being possible, it seems unreasonable to expect a switchdev driver writer to get it right from the first try. Therefore, now that DSA has experimented with the bridge replay helpers for a little bit, we can move the code to the bridge driver where it is more readily available to all switchdev drivers. To convert the switchdev object replay helpers from "pull mode" (where the driver asks for them) to a "push mode" (where the bridge offers them automatically), the biggest problem is that the bridge needs to be aware when a switchdev port joins and leaves, even when the switchdev is only indirectly a bridge port (for example when the bridge port is a LAG upper of the switchdev). Luckily, we already have a hook for that, in the form of the newly introduced switchdev_bridge_port_offload() and switchdev_bridge_port_unoffload() calls. These offer a natural place for hooking the object addition and deletion replays. Extend the above 2 functions with: - pointers to the switchdev atomic notifier (for FDB replays) and the blocking notifier (for MDB and VLAN replays). - the "const void *ctx" argument required for drivers to be able to disambiguate between which port is targeted, when multiple ports are lowers of the same LAG that is a bridge port. Most of the drivers pass NULL to this argument, except the ones that support LAG offload and have the proper context check already in place in the switchdev blocking notifier handler. Also unexport the replay helpers, since nobody except the bridge calls them directly now. Note that: (a) we abuse the terminology slightly, because FDB entries are not "switchdev objects", but we count them as objects nonetheless. With no direct way to prove it, I think they are not modeled as switchdev objects because those can only be installed by the bridge to the hardware (as opposed to FDB entries which can be propagated in the other direction too). This is merely an abuse of terms, FDB entries are replayed too, despite not being objects. (b) the bridge does not attempt to sync port attributes to newly joined ports, just the countable stuff (the objects). The reason for this is simple: no universal and symmetric way to sync and unsync them is known. For example, VLAN filtering: what to do on unsync, disable or leave it enabled? Similarly, STP state, ageing timer, etc etc. What a switchdev port does when it becomes standalone again is not really up to the bridge's competence, and the driver should deal with it. On the other hand, replaying deletions of switchdev objects can be seen a matter of cleanup and therefore be treated by the bridge, hence this patch. We make the replay helpers opt-in for drivers, because they might not bring immediate benefits for them: - nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(), so br_vlan_replay() should not do anything for the new drivers on which we call it. The existing drivers where there was even a slight possibility for there to exist a VLAN on a bridge port before they join it are already guarded against this: mlxsw and prestera deny joining LAG interfaces that are members of a bridge. - br_fdb_replay() should now notify of local FDB entries, but I patched all drivers except DSA to ignore these new entries in commit 2c4eca3ef716 ("net: bridge: switchdev: include local flag in FDB notifications"). Driver authors can lift this restriction as they wish, and when they do, they can also opt into the FDB replay functionality. - br_mdb_replay() should fix a real issue which is described in commit 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries"). However most drivers do not offload the SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw offload this switchdev object, and I don't completely understand the way in which they offload this switchdev object anyway. So I'll leave it up to these drivers' respective maintainers to opt into br_mdb_replay(). So most of the drivers pass NULL notifier blocks for the replay helpers, except: - dpaa2-switch which was already acked/regression-tested with the helpers enabled (and there isn't much of a downside in having them) - ocelot which already had replay logic in "pull" mode - DSA which already had replay logic in "pull" mode An important observation is that the drivers which don't currently request bridge event replays don't even have the switchdev_bridge_port_{offload,unoffload} calls placed in proper places right now. This was done to avoid unnecessary rework for drivers which might never even add support for this. For driver writers who wish to add replay support, this can be used as a tentative placement guide: https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/ Cc: Vadym Kochan <vkochan@marvell.com> Cc: Taras Chornyi <tchornyi@marvell.com> Cc: Ioana Ciornei <ioana.ciornei@nxp.com> Cc: Lars Povlsen <lars.povlsen@microchip.com> Cc: Steen Hegelund <Steen.Hegelund@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22net: bridge: switchdev: let drivers inform which bridge ports are offloadedVladimir Oltean1-5/+19
On reception of an skb, the bridge checks if it was marked as 'already forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it is, it assigns the source hardware domain of that skb based on the hardware domain of the ingress port. Then during forwarding, it enforces that the egress port must have a different hardware domain than the ingress one (this is done in nbp_switchdev_allowed_egress). Non-switchdev drivers don't report any physical switch id (neither through devlink nor .ndo_get_port_parent_id), therefore the bridge assigns them a hardware domain of 0, and packets coming from them will always have skb->offload_fwd_mark = 0. So there aren't any restrictions. Problems appear due to the fact that DSA would like to perform software fallback for bonding and team interfaces that the physical switch cannot offload. +-- br0 ---+ / / | \ / / | \ / | | bond0 / | | / \ swp0 swp1 swp2 swp3 swp4 There, it is desirable that the presence of swp3 and swp4 under a non-offloaded LAG does not preclude us from doing hardware bridging beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high enough that software bridging between {swp0,swp1,swp2} and bond0 is not impractical. But this creates an impossible paradox given the current way in which port hardware domains are assigned. When the driver receives a packet from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to something. - If we set it to 0, then the bridge will forward it towards swp1, swp2 and bond0. But the switch has already forwarded it towards swp1 and swp2 (not to bond0, remember, that isn't offloaded, so as far as the switch is concerned, ports swp3 and swp4 are not looking up the FDB, and the entire bond0 is a destination that is strictly behind the CPU). But we don't want duplicated traffic towards swp1 and swp2, so it's not ok to set skb->offload_fwd_mark = 0. - If we set it to 1, then the bridge will not forward the skb towards the ports with the same switchdev mark, i.e. not to swp1, swp2 and bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should have forwarded the skb there. So the real issue is that bond0 will be assigned the same hardware domain as {swp0,swp1,swp2}, because the function that assigns hardware domains to bridge ports, nbp_switchdev_add(), recurses through bond0's lower interfaces until it finds something that implements devlink (calls dev_get_port_parent_id with bool recurse = true). This is a problem because the fact that bond0 can be offloaded by swp3 and swp4 in our example is merely an assumption. A solution is to give the bridge explicit hints as to what hardware domain it should use for each port. Currently, the bridging offload is very 'silent': a driver registers a netdevice notifier, which is put on the netns's notifier chain, and which sniffs around for NETDEV_CHANGEUPPER events where the upper is a bridge, and the lower is an interface it knows about (one registered by this driver, normally). Then, from within that notifier, it does a bunch of stuff behind the bridge's back, without the bridge necessarily knowing that there's somebody offloading that port. It looks like this: ip link set swp0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v call_netdevice_notifiers | v dsa_slave_netdevice_event | v oh, hey! it's for me! | v .port_bridge_join What we do to solve the conundrum is to be less silent, and change the switchdev drivers to present themselves to the bridge. Something like this: ip link set swp0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v bridge: Aye! I'll use this call_netdevice_notifiers ^ ppid as the | | hardware domain for v | this port, and zero dsa_slave_netdevice_event | if I got nothing. | | v | oh, hey! it's for me! | | | v | .port_bridge_join | | | +------------------------+ switchdev_bridge_port_offload(swp0, swp0) Then stacked interfaces (like bond0 on top of swp3/swp4) would be treated differently in DSA, depending on whether we can or cannot offload them. The offload case: ip link set bond0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v bridge: Aye! I'll use this call_netdevice_notifiers ^ ppid as the | | switchdev mark for v | bond0. dsa_slave_netdevice_event | Coincidentally (or not), | | bond0 and swp0, swp1, swp2 v | all have the same switchdev hmm, it's not quite for me, | mark now, since the ASIC but my driver has already | is able to forward towards called .port_lag_join | all these ports in hw. for it, because I have | a port with dp->lag_dev == bond0. | | | v | .port_bridge_join | for swp3 and swp4 | | | +------------------------+ switchdev_bridge_port_offload(bond0, swp3) switchdev_bridge_port_offload(bond0, swp4) And the non-offload case: ip link set bond0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v bridge waiting: call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload | | wasn't called, okay, I'll use a v | hwdom of zero for this one. dsa_slave_netdevice_event : Then packets received on swp0 will | : not be software-forwarded towards v : swp1, but they will towards bond0. it's not for me, but bond0 is an upper of swp3 and swp4, but their dp->lag_dev is NULL because they couldn't offload it. Basically we can draw the conclusion that the lowers of a bridge port can come and go, so depending on the configuration of lowers for a bridge port, it can dynamically toggle between offloaded and unoffloaded. Therefore, we need an equivalent switchdev_bridge_port_unoffload too. This patch changes the way any switchdev driver interacts with the bridge. From now on, everybody needs to call switchdev_bridge_port_offload and switchdev_bridge_port_unoffload, otherwise the bridge will treat the port as non-offloaded and allow software flooding to other ports from the same ASIC. Note that these functions lay the ground for a more complex handshake between switchdev drivers and the bridge in the future. For drivers that will request a replay of the switchdev objects when they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we place the call to switchdev_bridge_port_unoffload() strategically inside the NETDEV_PRECHANGEUPPER notifier's code path, and not inside NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers need the netdev adjacency lists to be valid, and that is only true in NETDEV_PRECHANGEUPPER. Cc: Vadym Kochan <vkochan@marvell.com> Cc: Taras Chornyi <tchornyi@marvell.com> Cc: Ioana Ciornei <ioana.ciornei@nxp.com> Cc: Lars Povlsen <lars.povlsen@microchip.com> Cc: Steen Hegelund <Steen.Hegelund@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-16net: switchdev: Simplify 'mlxsw_sp_mc_write_mdb_entry()'Christophe JAILLET1-5/+3
Use 'bitmap_alloc()/bitmap_free()' instead of hand-writing it. This makes the code less verbose. Also, use 'bitmap_alloc()' instead of 'bitmap_zalloc()' because the bitmap is fully overridden by a 'bitmap_copy()' call just after its allocation. While at it, remove an extra and unneeded space. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-29net: switchdev: add a context void pointer to struct switchdev_notifier_infoVladimir Oltean1-3/+3
In the case where the driver asks for a replay of a certain type of event (port object or attribute) for a bridge port that is a LAG, it may do so because this port has just joined the LAG. But there might already be other switchdev ports in that LAG, and it is preferable that those preexisting switchdev ports do not act upon the replayed event. The solution is to add a context to switchdev events, which is NULL most of the time (when the bridge layer initiates the call) but which can be set to a value controlled by the switchdev driver when a replay is requested. The driver can then check the context to figure out if all ports within the LAG should act upon the switchdev event, or just the ones that match the context. We have to modify all switchdev_handle_* helper functions as well as the prototypes in the drivers that use these helpers too, because these helpers hide the underlying struct switchdev_notifier_info from us and there is no way to retrieve the context otherwise. The context structure will be populated and used in later patches. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-25mlxsw: core_env: Avoid unnecessary memcpy()sIdo Schimmel1-8/+8
Simply get a pointer to the data in the register payload instead of copying it to a temporary buffer. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-21mlxsw: core: Add support for module EEPROM read by pageIdo Schimmel4-0/+108
Add support for ethtool_ops::get_module_eeprom_by_page() which allows user space to read transceiver module EEPROM based on passed parameters. The I2C address is not validated in order to avoid module-specific code. In case of wrong address, error will be returned from device's firmware. Tested by comparing output with legacy method (ioctl) output. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Vadim Pasternak <vadimp@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-21mlxsw: reg: Document possible MCIA status valuesIdo Schimmel1-0/+14
Will be used to emit meaningful messages to user space via extack in a subsequent patch. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-21mlxsw: reg: Add bank number to MCIA registerIdo Schimmel1-0/+6
Add bank number to MCIA (Management Cable Info Access) register in order to allow access to banked pages on EEPROMs using CMIS (Common Management Interface Specification) memory map. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski3-4/+9
Trivial conflicts in net/can/isotp.c and tools/testing/selftests/net/mptcp/mptcp_connect.sh scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c to include/linux/ptp_clock_kernel.h in -next so re-apply the fix there. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-06-16mlxsw: spectrum_router: remove redundant continue statementColin Ian King1-1/+0
The continue statement at the end of a for-loop has no effect, remove it. Addresses-Coverity: ("Continue has no effect") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-10mlxsw: thermal: Fix null dereference of NULL temperature parameterColin Ian King1-2/+2
The call to mlxsw_thermal_module_temp_and_thresholds_get passes a NULL pointer for the temperature and this can be dereferenced in this function if the mlxsw_reg_query call fails. The simplist fix is to pass the address of dummy temperature variable instead of a NULL pointer. Addresses-Coverity: ("Explicit null dereferenced") Fixes: 72a64c2fe9d8 ("mlxsw: thermal: Read module temperature thresholds using MTMP register") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-09mlxsw: thermal: Read module temperature thresholds using MTMP registerMykola Kostenok1-17/+30
mlxsw_thermal_module_trips_update() is used to update the trip points of the module's thermal zone. Currently, this is done by querying the thresholds from the module's EEPROM via MCIA register. This data does not pass validation and in some cases can be unreliable. For example, due to some problem with transceiver module. Previous patch made it possible to read module's temperature and thresholds via MTMP register. Therefore, extend mlxsw_thermal_module_trips_update() to use the thresholds queried from MTMP, if valid. This is both more reliable and more efficient than current method, as temperature and thresholds are queried in one transaction instead of three. This is significant when working over a slow bus such as I2C. Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com> Acked-by: Vadim Pasternak <vadimp@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-09mlxsw: thermal: Add function for reading module temperature and thresholdsMykola Kostenok1-15/+35
Provide new function mlxsw_thermal_module_temp_and_thresholds_get() for reading temperature and temperature thresholds by a single operation. The motivation is to reduce the number of transactions with the device which is important when operating over a slow bus such as I2C. Currently, the sole caller of the function is only using it to read the module's temperature. The next patch will also use it to query the module's temperature thresholds. Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com> Acked-by: Vadim Pasternak <vadimp@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-09mlxsw: core_env: Read module temperature thresholds using MTMP registerMykola Kostenok1-2/+11
Currently, module temperature thresholds are obtained from Management Cable Info Access (MCIA) register by specifying the thresholds offsets within module EEPROM layout. This data does not pass validation and in some cases can be unreliable. For example, due to some problem with the module. Add support for a new feature provided by Management Temperature (MTMP) register for sanitization of temperature thresholds values. Extend mlxsw_env_module_temp_thresholds_get() to get temperature thresholds through MTMP field 'max_operational_temperature' - if it is not zero, feature is supported. Otherwise fallback to old method and get the thresholds through MCIA. Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com> Acked-by: Vadim Pasternak <vadimp@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-09mlxsw: reg: Extend MTMP register with new threshold fieldMykola Kostenok4-8/+26
Extend Management Temperature (MTMP) register with new field specifying the maximum temperature threshold. Extend mlxsw_reg_mtmp_unpack() function with two extra arguments, providing high and maximum temperature thresholds. For modules, these thresholds correspond to critical and emergency thresholds that are read from the module's EEPROM. Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com> Acked-by: Vadim Pasternak <vadimp@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-09mlxsw: spectrum_router: Remove abort mechanismAmit Cohen2-125/+5
The abort mechanism was introduced in commit 8e05fd7166c6 ("fib: hook IPv4 fib for hardware offload") with the purpose of falling back to software-based routing in case of a route programming error in hardware. The process is irreversible and requires users to reload the offloading driver or reboot the machine. While this approach might make sense in theory, it makes very little sense in practice. In the case of high speed ASICs such as the Spectrum ASIC, the abort mechanism effectively kills the machine upon a non-fatal error such as a route programming error. Such an extreme policy does not belong in the kernel, especially when user space can simply try to reprogram the route following the RTM_NEWROUTE failure notification. Therefore, remove the abort mechanism. Signed-off-by: Amit Cohen <amcohen@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-07mlxsw: core: Set thermal zone polling delay argument to real value at initMykola Kostenok1-2/+4
Thermal polling delay argument for modules and gearboxes thermal zones used to be initialized with zero value, while actual delay was used to be set by mlxsw_thermal_set_mode() by thermal operation callback set_mode(). After operations set_mode()/get_mode() have been removed by cited commits, modules and gearboxes thermal zones always have polling time set to zero and do not perform temperature monitoring. Set non-zero "polling_delay" in thermal_zone_device_register() routine, thus, the relevant thermal zones will perform thermal monitoring. Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com> Fixes: 5d7bd8aa7c35 ("thermal: Simplify or eliminate unnecessary set_mode() methods") Fixes: 1ee14820fd8e ("thermal: remove get_mode() operation of drivers") Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com> Acked-by: Vadim Pasternak <vadimp@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-07mlxsw: spectrum_qdisc: Pass handle, not band number to find_class()Petr Machata1-1/+4
In mlxsw Qdisc offload, find_class() is an operation that yields a qdisc offload descriptor given a parental qdisc descriptor and a class handle. In __mlxsw_sp_qdisc_ets_graft() however, a band number is passed to that function instead of a handle. This can lead to a trigger of a WARN_ON with the following splat: WARNING: CPU: 3 PID: 808 at drivers/net/ethernet/mellanox/mlxsw/spectrum_qdisc.c:1356 __mlxsw_sp_qdisc_ets_graft+0x115/0x130 [mlxsw_spectrum] [...] Call Trace: mlxsw_sp_setup_tc_prio+0xe3/0x100 [mlxsw_spectrum] qdisc_offload_graft_helper+0x35/0xa0 prio_graft+0x176/0x290 [sch_prio] qdisc_graft+0xb3/0x540 tc_modify_qdisc+0x56a/0x8a0 rtnetlink_rcv_msg+0x12c/0x370 netlink_rcv_skb+0x49/0xf0 netlink_unicast+0x1f6/0x2b0 netlink_sendmsg+0x1fb/0x410 ____sys_sendmsg+0x1f3/0x220 ___sys_sendmsg+0x70/0xb0 __sys_sendmsg+0x54/0xa0 do_syscall_64+0x3a/0x70 entry_SYSCALL_64_after_hwframe+0x44/0xae Since the parent handle is not passed with the offload information, compute it from the band number and qdisc handle. Fixes: 28052e618b04 ("mlxsw: spectrum_qdisc: Track children per qdisc") Reported-by: Maksym Yaremchuk <maksymy@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-07mlxsw: reg: Spectrum-3: Enforce lowest max-shaper burst size of 11Petr Machata1-1/+1
A max-shaper is the HW component responsible for delaying egress traffic above a configured transmission rate. Burst size is the amount of traffic that is allowed to pass without accounting. The burst size value needs to be such that it can be expressed as 2^BS * 512 bits, where BS lies in a certain ASIC-dependent range. mlxsw enforces that this holds before attempting to configure the shaper. The assumption for Spectrum-3 was that the lower limit of BS would be 5, like for Spectrum-1. But as of now, the limit is still 11. Therefore fix the driver accordingly, so that incorrect values are rejected early with a proper message. Fixes: 23effa2479ba ("mlxsw: reg: Add max_shaper_bs to QoS ETS Element Configuration") Reported-by: Maksym Yaremchuk <maksymy@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-28mlxsw: core: use PSID string define in devlink infoJiri Pirko1-1/+3
Instead of having the string spelled out in the driver, use the global define with the same value. Signed-off-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-05-28mlxsw: core: Expose FW version over defined keywordJiri Pirko1-1/+3
To be aligned with the rest of the drivers, expose FW version under "fw" keyword in devlink dev info, in addition to the existing "fw.version", which is currently Mellanox-specific. devlink output before: running: fw.version 30.2008.2018 after: running: fw.version 30.2008.2018 fw 30.2008.2018 Signed-off-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-05-19mlxsw: spectrum_router: Add support for custom multipath hash policyIdo Schimmel1-0/+85
When this policy is set, only enable the packet fields that were enabled by user space for multipath hash computation. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-19mlxsw: spectrum_router: Add support for inner layer 3 multipath hash policyIdo Schimmel1-0/+41
When this policy is set, the kernel uses the inner layer 3 fields for multipath hash computation and falls back to the outer fields if no encapsulation was encountered. This behavior is most likely influenced by the behavior of the flow dissector, which is used for the packet dissection. The Spectrum ASIC, however, cannot fallback to outer fields if inner fields are not available. This should not result in a discrepancy from the software data path because if several flows have matching inner fields, they will tend to have matching outer fields as well. Therefore, implement this policy by enabling both outer and inner layer 3 fields for the multipath hash computation. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-19mlxsw: spectrum_outer: Factor out helper for common outer fieldsIdo Schimmel1-20/+28
Outer IPv4 and IPv6 addresses are used by multiple multipath hash policies. Factor out helpers that set these fields to increase code sharing between different policies. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-19mlxsw: reg: Add inner packet fields to RECRv2 registerIdo Schimmel1-0/+42
The RECRv2 register is used for setting up the router's ECMP hash configuration. Extend it with inner packet fields to allow the ECMP hash to be calculated based on inner flow information. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-19mlxsw: spectrum_router: Move multipath hash configuration to a bitmapIdo Schimmel2-80/+64
Currently, the multipath hash configuration is written directly to the register payload. While this is OK for the two currently supported policies, it is going to be hard to follow when more policies and more packet fields are added. Instead, set the required headers and fields in a bitmap and then dump it to the register payload. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-19mlxsw: spectrum_router: Replace if statement with a switch statementIdo Schimmel1-31/+38
The code was written when only two multipath hash policies were present, so the if statement was sufficient. The next patch and future patches are going to add support for more policies, so move to a switch statement. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-18mlxsw: Remove Mellanox SwitchX-2 ASIC supportAmit Cohen6-1719/+0
Initial support for the Mellanox SwitchX-2 ASIC was added in July 2015. Since then all development efforts shifted towards the Mellanox Spectrum ASICs and development of this driver stopped beside trivial fixes and refactoring. Therefore, the driver does not support any switch offloads and simply traps all traffic to the CPU, rendering it irrelevant for deployment. In addition, support for this ASIC was dropped by Mellanox a few years ago. Given the driver is not used by any users and that there is no intention of investing in its development, remove it from the kernel. Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-18mlxsw: Remove Mellanox SwitchIB ASIC supportAmit Cohen4-610/+0
Initial support for the Mellanox SwitchIB and SwitchIB-2 ASICs was added in October 2016, but since then development of this driver stopped. Therefore, the driver does not support any offloads and simply registers devlink ports for its front panel ports, rendering it irrelevant for deployment. Given the driver is not used by any users and that there is no intention of investing in its development, remove it from the kernel. Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-18mlxsw: spectrum_router: Avoid missing error code warningIdo Schimmel1-2/+4
Explicitly set the error code to zero before the goto statement to avoid the following smatch warning: drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3598 mlxsw_sp_nexthop_group_refresh() warn: missing error code 'err' The warning is a false positive, but the change both suppresses the warning and makes it clear to future readers that this is not an error path. The original report and discussion can be found here [1]. [1] https://lore.kernel.org/lkml/202105141823.Td2h3Mbi-lkp@intel.com/ Cc: Dan Carpenter <dan.carpenter@oracle.com> Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-18mlxsw: core: Avoid unnecessary EMAD buffer copyIdo Schimmel1-1/+1
mlxsw_emad_transmit() takes care of sending EMAD transactions to the device. Since these transactions can time out, the driver performs up to 5 retransmissions, each time copying the skb with the original request. The data of the skb does not change throughout the process, so there is no need to copy it each time. Instead, only the skb itself can be copied. Therefore, use skb_clone() instead of skb_copy(). This reduces the latency of the function by about 16%. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-18mlxsw: Verify the accessed index doesn't exceed the array lengthDanielle Ratson5-0/+19
There are few cases in which an array index queried from a fw register, is accessed without any validation that it doesn't exceed the array length. Add a proper length validation, so accessing memory past the end of an array will be forbidden. Signed-off-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-18mlxsw: spectrum_buffers: Switch function argumentsDanielle Ratson1-3/+3
In the call path: mlxsw_sp_hdroom_bufs_reset_sizes() mlxsw_sp_hdroom_int_buf_size_get() ->int_buf_size_get() The 'speed' and 'mtu' arguments were mistakenly switched twice. The two bugs thus canceled each other. Clean this up by switching the arguments in both call sites, so that they are passed in the right order. Found during manual code inspection. Signed-off-by: Danielle Ratson <danieller@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-08Merge tag 'net-5.13-rc1' of ↵Linus Torvalds1-15/+15
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Networking fixes for 5.13-rc1, including fixes from bpf, can and netfilter trees. Self-contained fixes, nothing risky. Current release - new code bugs: - dsa: ksz: fix a few bugs found by static-checker in the new driver - stmmac: fix frame preemption handshake not triggering after interface restart Previous releases - regressions: - make nla_strcmp handle more then one trailing null character - fix stack OOB reads while fragmenting IPv4 packets in openvswitch and net/sched - sctp: do asoc update earlier in sctp_sf_do_dupcook_a - sctp: delay auto_asconf init until binding the first addr - stmmac: clear receive all(RA) bit when promiscuous mode is off - can: mcp251x: fix resume from sleep before interface was brought up Previous releases - always broken: - bpf: fix leakage of uninitialized bpf stack under speculation - bpf: fix masking negation logic upon negative dst register - netfilter: don't assume that skb_header_pointer() will never fail - only allow init netns to set default tcp cong to a restricted algo - xsk: fix xp_aligned_validate_desc() when len == chunk_size to avoid false positive errors - ethtool: fix missing NLM_F_MULTI flag when dumping - can: m_can: m_can_tx_work_queue(): fix tx_skb race condition - sctp: fix a SCTP_MIB_CURRESTAB leak in sctp_sf_do_dupcook_b - bridge: fix NULL-deref caused by a races between assigning rx_handler_data and setting the IFF_BRIDGE_PORT bit Latecomer: - seg6: add counters support for SRv6 Behaviors" * tag 'net-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (73 commits) atm: firestream: Use fallthrough pseudo-keyword net: stmmac: Do not enable RX FIFO overflow interrupts mptcp: fix splat when closing unaccepted socket i40e: Remove LLDP frame filters i40e: Fix PHY type identifiers for 2.5G and 5G adapters i40e: fix the restart auto-negotiation after FEC modified i40e: Fix use-after-free in i40e_client_subtask() i40e: fix broken XDP support netfilter: nftables: avoid potential overflows on 32bit arches netfilter: nftables: avoid overflows in nft_hash_buckets() tcp: Specify cmsgbuf is user pointer for receive zerocopy. mlxsw: spectrum_mr: Update egress RIF list before route's action net: ipa: fix inter-EE IRQ register definitions can: m_can: m_can_tx_work_queue(): fix tx_skb race condition can: mcp251x: fix resume from sleep before interface was brought up can: mcp251xfd: mcp251xfd_probe(): add missing can_rx_offload_del() in error path can: mcp251xfd: mcp251xfd_probe(): fix an error pointer dereference in probe netfilter: nftables: Fix a memleak from userdata error path in new objects netfilter: remove BUG_ON() after skb_header_pointer() netfilter: nfnetlink_osf: Fix a missing skb_header_pointer() NULL check ...
generated by cgit v1.2.3 (git 2.39.0) at 2024-10-04 00:43:48 +0300