| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This is the 5.10.67 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
[ Upstream commit 87b8061bad9bd4b549b2daf36ffbaa57be2789a2 ]
This fixes two issues that cause the sysrq sequence to be inadvertently
aborted on SCIF serial consoles:
- a NUL character remains in the RX queue after a break has been detected,
which is then passed on to uart_handle_sysrq_char()
- the break interrupt is handled twice on controllers with multiplexed ERI
and BRI interrupts
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1fe0e1fa3209ad8e9124147775bd27b1d9f04bd4 ]
Handle optional overrun-throttle-ms property as done for 8250_fsl in commit
6d7f677a2afa ("serial: 8250: Rate limit serial port rx interrupts during
input overruns"). This can be used to rate limit the UART interrupts on
noisy lines that end up producing messages like the following:
ttyS ttyS2: 4 input overrun(s)
At least on droid4, the multiplexed USB and UART port is left to UART mode
by the bootloader for a debug console, and if a USB charger is connected
on boot, we get noise on the UART until the PMIC related drivers for PHY
and charger are loaded.
With this patch and overrun-throttle-ms = <500> we avoid the extra rx
interrupts.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103533.51547-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3a96e97ab4e835078e6f27b7e1c0947814df3841 ]
The bar and offset parameters to setup_port() are used in pointer math,
and while it would be very difficult to get them to wrap as a negative
number, just be "safe" and make them unsigned so that static checkers do
not trip over them unintentionally.
Cc: Jiri Slaby <jirislaby@kernel.org>
Reported-by: Jordy Zomer <jordy@pwning.systems>
Link: https://lore.kernel.org/r/20210726130717.2052096-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7ccbdcc4d08a6d7041e4849219bbb12ffa45db4c ]
The alloc_tty_driver failure is handled gracefully in hvsi_init. But
tty_register_driver is not. panic is called if that one fails.
So handle the failure of tty_register_driver gracefully too. This will
keep at least the console functional as it was enabled earlier by
console_initcall in hvsi_console_init. Instead of shooting down the
whole system.
This means, we disable interrupts and restore hvsi_wait back to
poll_for_state().
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d7aff291d069c4418285f3c8ee27b0ff67ce5998 ]
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 240e126c28df084222f0b661321e8e3ecb0d232e ]
uart_handle_dcd_change() requires a port lock to be held and will emit a
warning when lockdep is enabled.
Held corresponding lock to fix the following warnings.
[ 132.528648] WARNING: CPU: 5 PID: 11600 at drivers/tty/serial/serial_core.c:3046 uart_handle_dcd_change+0xf4/0x120
[ 132.530482] Modules linked in:
[ 132.531050] CPU: 5 PID: 11600 Comm: jsm Not tainted 5.14.0-rc1-00003-g7fef2edf7cc7-dirty #31
[ 132.535268] RIP: 0010:uart_handle_dcd_change+0xf4/0x120
[ 132.557100] Call Trace:
[ 132.557562] ? __free_pages+0x83/0xb0
[ 132.558213] neo_parse_modem+0x156/0x220
[ 132.558897] neo_param+0x399/0x840
[ 132.559495] jsm_tty_open+0x12f/0x2d0
[ 132.560131] uart_startup.part.18+0x153/0x340
[ 132.560888] ? lock_is_held_type+0xe9/0x140
[ 132.561660] uart_port_activate+0x7f/0xe0
[ 132.562351] ? uart_startup.part.18+0x340/0x340
[ 132.563003] tty_port_open+0x8d/0xf0
[ 132.563523] ? uart_set_options+0x1e0/0x1e0
[ 132.564125] uart_open+0x24/0x40
[ 132.564604] tty_open+0x15c/0x630
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/1626242003-3809-1-git-send-email-zheyuma97@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 5.10.65 stable release
|
|
commit bb2853a6a421a052268eee00fd5d3f6b3504b2b1 upstream.
The ops->receive_buf() may be accessed concurrently from these two
functions. If the driver flushes data to the line discipline
receive_buf() method while tiocsti() is waiting for the
ops->receive_buf() to finish its work, the data race will happen.
For example:
tty_ioctl |tty_ldisc_receive_buf
->tioctsi | ->tty_port_default_receive_buf
| ->tty_ldisc_receive_buf
->hci_uart_tty_receive | ->hci_uart_tty_receive
->h4_recv | ->h4_recv
In this case, the h4 receive buffer will be overwritten by the
latecomer, and we will lost the data.
Hence, change tioctsi() function to use the exclusive lock interface
from tty_buffer to avoid the data race.
Reported-by: syzbot+97388eb9d31b997fe1d0@syzkaller.appspotmail.com
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210823000641.2082292-1-phind.uet@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d5c38948448abc2bb6b36dbf85a554bf4748885e ]
Register offset needs to be applied on mapbase also.
dma_tx/rx_request use the physical address of UARTDATA.
Register offset is currently only applied to membase (the
corresponding virtual addr) but not on mapbase.
Fixes: 24b1e5f0e83c ("tty: serial: lpuart: add imx7ulp support")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Adriana Reus <adriana.reus@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Andy Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20210819021033.32606-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6f991850412963381017cfb0d691cbd4d6a551dc upstream.
With commit 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable"),
below warning is seen with W=1 and CONFIG_SERIAL_8250_DMA is disabled:
drivers/tty/serial/8250/8250_omap.c:1199:42: warning: unused variable 'k3_soc_devices' [-Wunused-const-variable]
Fix this by moving the code using k3_soc_devices array to
omap_serial_fill_features_erratas() that handles other errata flags as
well.
Fixes: 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d4548b14dd7e5c698f81ce23ce7b69a896373b45 upstream.
k3_soc_devices array is missing a sentinel entry which may result in out
of bounds access as reported by kernel KASAN.
Fix this by adding a sentinel entry.
Fixes: 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-1-vigneshr@ti.com
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2287a51ba822384834dafc1c798453375d1107c7 upstream.
As per the long-suffering comment.
Reported-by: Minh Yuan <yuanmingbuaa@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 5.10.60 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
commit 341abd693d10e5f337a51f140ae3e7a1ae0febf6 upstream.
This attempts to fix a bug found with a serial port card which uses
an MCS9922 chip, one of the 4 models for which MSI-X interrupts are
currently supported. I don't possess such a card, and i'm not
experienced with the serial subsystem, so this patch is based on what
i think i found as a likely reason for failure, based on walking the
user who actually owns the card through some diagnostic.
The user who reported the problem finds the following in his dmesg
output for the relevant ttyS4 and ttyS5:
[ 0.580425] serial 0000:02:00.0: enabling device (0000 -> 0003)
[ 0.601448] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 125, base_baud = 115200) is a ST16650V2
[ 0.603089] serial 0000:02:00.1: enabling device (0000 -> 0003)
[ 0.624119] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 126, base_baud = 115200) is a ST16650V2
...
[ 6.323784] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
[ 6.324128] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
...
Output of setserial -a:
/dev/ttyS4, Line 4, UART: 16650V2, Port: 0x3010, IRQ: 127
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000
Flags: spd_normal skip_test
This suggests to me that the serial driver wants to register and share a
MSI/MSI-X irq 128 with the xhci_hcd driver, whereas the xhci driver does
not want to share the irq, as flags 0x00000080 (== IRQF_SHARED) from the
serial port driver means to share the irq, and this mismatch ends in some
failed irq init?
With this setup, data reception works very unreliable, with dropped data,
already at a transmission rate of only a 16 Bytes chunk every 1/120th of
a second, ie. 1920 Bytes/sec, presumably due to rx fifo overflow due to
mishandled or not used at all rx irq's?
See full discussion thread with attempted diagnosis at:
https://psychtoolbox.discourse.group/t/issues-with-iscan-serial-port-recording/3886
Disabling the use of MSI interrupts for the serial port pci card did
fix the reliability problems. The user executed the following sequence
of commands to achieve this:
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.0/msi_bus
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.1/msi_bus
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/bind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/bind
This resulted in the following log output:
[ 82.179021] pci 0000:02:00.0: MSI/MSI-X disallowed for future drivers
[ 87.003031] pci 0000:02:00.1: MSI/MSI-X disallowed for future drivers
[ 98.537010] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 17, base_baud = 115200) is a ST16650V2
[ 103.648124] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 18, base_baud = 115200) is a ST16650V2
This patch attempts to fix the problem by disabling irq sharing when
using MSI irq's. Note that all i know for sure is that disabling MSI
irq's fixed the problem for the user, so this patch could be wrong and
is untested. Please review with caution, keeping this in mind.
Fixes: 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support")
Cc: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: https://lore.kernel.org/r/20210729043306.18528-1-mario.kleiner.de@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f0909db761535aefafa77031062603a71557267 upstream.
Elkhart Lake UARTs are PCI enumerated Synopsys DesignWare v4.0+ UART
integrated with Intel iDMA 32-bit DMA controller. There is a specific
driver to handle them, i.e. 8250_lpss. Hence, disable 8250_pci
enumeration for these UARTs.
Fixes: 1b91d97c66ef ("serial: 8250_lpss: Add ->setup() for Elkhart Lake ports")
Fixes: 4f912b898dc2 ("serial: 8250_lpss: Enable HS UART on Elkhart Lake")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210713101739.36962-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e5227c51090e165db4b48dcaa300605bfced7014 upstream.
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7c4a509d3815a260c423c0633bd73695250ac26d upstream.
Fix uart corruption issue when rx power off.
Add spin lock in mtk8250_dma_rx_complete function in APDMA mode.
when uart is used as a communication port with external device(GPS).
when external device(GPS) power off, the power of rx pin is also from
1.8v to 0v. Even if there is not any data in rx. But uart rx pin can
capture the data "0".
If uart don't receive any data in specified cycle, uart will generates
BI(Break interrupt) interrupt.
If external device(GPS) power off, we found that BI interrupt appeared
continuously and very frequently.
When uart interrupt type is BI, uart IRQ handler(8250 framwork
API:serial8250_handle_irq) will push data to tty buffer.
mtk8250_dma_rx_complete is a task of mtk_uart_apdma_rx_handler.
mtk8250_dma_rx_complete priority is lower than uart irq
handler(serial8250_handle_irq).
if we are in process of mtk8250_dma_rx_complete, uart appear BI
interrupt:1)serial8250_handle_irq will priority execution.2)it may cause
write tty buffer conflict in mtk8250_dma_rx_complete.
So the spin lock protect the rx receive data process is not break.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210729084640.17613-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cc9ca4d95846cbbece48d9cd385550f8fba6a3c1 upstream.
The Tegra serial driver always prints an error message when enabling the
FIFO for devices that have support for checking the FIFO enable status.
Fix this by displaying the error message, only when an error occurs.
Finally, update the error message to make it clear that enabling the
FIFO failed and display the error code.
Fixes: 222dcdff3405 ("serial: tegra: check for FIFO mode enabled status")
Cc: <stable@vger.kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210630125643.264264-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 5.10.53 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
[ Upstream commit d157fca711ad42e75efef3444c83d2e1a17be27a ]
Remove the hack to assign the global console_port variable at probe time.
This assumption that cons->index is -1 is wrong for systems that specify
'console=' in the cmdline (or 'stdout-path' in dts). Hence, on such system
the actual console assignment is ignored, and the first UART that happens
to be probed is used as console instead.
Move the logic to console_setup() and map the console to the correct port
through the array of available ports instead.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20210528133321.1859346-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fad92b11047a748c996ebd6cfb164a63814eeb2e ]
In the probe function, if the final 'serial_config()' fails, 'info' is
leaking.
Add a resource handling path to free this memory.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/dc25f96b7faebf42e60fe8d02963c941cf4d8124.1621971720.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8cac2f6eb8548245e6f8fb893fc7f2a714952654 ]
SYSRQ doesn't work with DMA. This is because there is no error
indication whether a symbol had a framing error or not. Actually,
this is not completely correct, there is a bit in the data register
which is set in this case, but we'd have to read change the DMA access
to 16 bit and we'd need to post process the data, thus make the DMA
pointless in the first place.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-10-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fcb10ee27fb91b25b68d7745db9817ecea9f1038 ]
We should be very careful about the register values that will be used
for division or modulo operations, althrough the possibility that the
UARTBAUD register value is zero is very low, but we had better to deal
with the "bad data" of hardware in advance to avoid division or modulo
by zero leading to undefined kernel behavior.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210427021226.27468-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 5.10.50 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
[ Upstream commit deeaf963569a0d9d1b08babb771f61bb501a5704 ]
For default (x16) scheme which is currently used by mvebu-uart.c driver,
maximal divisor of UART base clock is 1023*16. Therefore there is limit for
minimal supported baudrate. This change calculate it correctly and prevents
setting invalid divisor 0 into hardware registers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-4-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ecd6b010d81f97b06b2f64d2d4f50ebf5acddaa9 ]
Testing mvuart->clk for non-error is not enough as mvuart->clk may contain
valid clk pointer but when clk_prepare_enable(mvuart->clk) failed then
port->uartclk is zero.
When mvuart->clk is not available then port->uartclk is zero too.
Parent clock rate port->uartclk is needed to calculate UART clock divisor
and without it is not possible to change baudrate.
So fix test condition when it is possible to change baudrate.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-3-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b67e830d38fa9335d927fe67e812e3ed81b4689c ]
On K3 family of SoCs (which includes AM654 SoC), it is observed that RX
TIMEOUT is signalled after RX FIFO has been drained, in which case a
dummy read of RX FIFO is required to clear RX TIMEOUT condition.
Otherwise, this would lead to an interrupt storm.
Fix this by introducing UART_RX_TIMEOUT_QUIRK flag and doing a dummy
read in IRQ handler when RX TIMEOUT is reported with no data in RX FIFO.
Fixes: be70874498f3 ("serial: 8250_omap: Add support for AM654 UART controller")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210622145704.11168-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 439c7183e5b97952bba1747f5ffc4dea45a6a18b ]
UARTs on TI SoCs prior to J7200 don't provide independent control over
RX FIFO not empty interrupt (RHR_IT) and RX timeout interrupt.
Starting with J7200 SoC, its possible to disable RHR_IT independent of
RX timeout interrupt using bit 2 of IER2 register. So disable RHR_IT
once RX DMA is started so as to avoid spurious interrupt being raised
when data is in the RX FIFO but is yet to be drained by DMA (a known
errata in older SoCs).
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201029051930.7097-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 78bcae8616ac277d6cb7f38e211493948ed73e30 ]
Support for magic baud rate divisors of 32770 and 32769 used with SMSC
Super I/O chips for extra baud rates of 230400 and 460800 respectively
where base rate is 115200[1] has been added around Linux 2.5.64, which
predates our repo history, but the origin could be identified as commit
2a717aad772f ("Merge with Linux 2.5.64.") with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>.
Code that is now in `serial8250_do_get_divisor' was added back then to
`serial8250_get_divisor', but that code would only ever trigger if one
of the higher baud rates was actually requested, and that cannot ever
happen, because the earlier call to `serial8250_get_baud_rate' never
returns them. This is because it calls `uart_get_baud_rate' with the
maximum requested being the base rate, that is clk/16 or 115200 for SMSC
chips at their nominal clock rate.
Fix it then and allow UPF_MAGIC_MULTIPLIER baud rates to be selected, by
requesting the maximum baud rate of clk/4 rather than clk/16 if the flag
has been set. Also correct the minimum baud rate, observing that these
ports only support actual (non-magic) divisors of up to 32767 only.
References:
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Table 31 - "Baud Rates", p. 77
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105190412280.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6ae7d0f5a92b9619f6e3c307ce56b2cefff3f0e9 ]
The error handling path is broken and we may un-register things that have
never been registered.
Update the loops index accordingly.
Fixes: 9842c38e9176 ("kfifo: fix warn_unused_result")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/e28c2e92c7475da25b03d022ea2d6dcf1ba807a2.1621968629.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 31a9a318255960d32ae183e95d0999daf2418608 ]
A 'request_irq()' call is not balanced by a corresponding 'free_irq()' in
the error handling path, as already done in the remove function.
Add it.
Fixes: 9842c38e9176 ("kfifo: fix warn_unused_result")
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/4f0d2b3038e82f081d370ccb0cade3ad88463fe7.1620580838.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d7e325aaa8c3593b5a572b583ecad79e95f32e7f ]
This loop ends on -1 so the error message will never be printed.
Fixes: 4bcf59a5dea0 ("serial: 8250: 8250_omap: Account for data in flight during DMA teardown")
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YIpd+kOpXKMpEXPf@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e60c2991f18bf221fa9908ff10cb24eaedaa9bae ]
The wrong code in set_mctrl() was already removed in commit 2b30efe2e88a
("tty: serial: lpuart: Remove unnecessary code from set_mctrl"), but the
code in get_mctrl() wasn't removed. It will not return the state of the
RTS or CTS line but whether automatic flow control is enabled, which is
wrong for the get_mctrl(). Thus remove it.
Fixes: 2b30efe2e88a ("tty: serial: lpuart: Remove unnecessary code from set_mctrl")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-7-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ccf08fd1204bcb5311cc10aea037c71c6e74720a ]
lpuart_rx_dma_startup() is used for both the 8 bit and the 32 bit
version of the LPUART. Modify the UARTCR only for the 8 bit version.
Fixes: f4eef224a09f ("serial: fsl_lpuart: add sysrq support when using dma")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 11b1d881a90fc184cc7d06e9804eb288c24a2a0d upstream.
The GLOBETROTTER.cis entry in serial_cs matches more devices than
intended and breaks them. Remove it.
Example: # pccardctl info
PRODID_1="Option International
"
PRODID_2="GSM-Ready 56K/ISDN
"
PRODID_3="021
"
PRODID_4="A
"
MANFID=0013,0000
FUNCID=0
result:
pcmcia 0.0: Direct firmware load for cis/GLOBETROTTER.cis failed with error -2
The GLOBETROTTER.cis is nowhere to be found. There's GLOBETROTTER.cis.ihex at
https://netdev.vger.kernel.narkive.com/h4inqdxM/patch-axnet-cs-fix-phy-id-detection-for-bogus-asix-chip#post41
It's from completely diffetent card:
vers_1 4.1, "Option International", "GSM/GPRS GlobeTrotter", "001", "A"
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210611201940.23898-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d495dd743d5ecd47288156e25c4d9163294a0992 upstream.
Add support for Option International GSM-Ready 56K/ISDN PCMCIA modem
card.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210611201940.23898-2-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 08a84410a04f05c7c1b8e833f552416d8eb9f6fe upstream.
Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following
message is possible output when system enters suspend and while
transferring data, because clearing TIE bit in SCSCR is not able to
stop any dmaengine transfer.
sh-sci e6550000.serial: ttySC1: Unable to drain transmitter
Note that this driver has already used some #ifdef in the .c file
so that this patch also uses #ifdef to fix the issue. Otherwise,
build errors happens if the CONFIG_SERIAL_SH_SCI_DMA is disabled.
Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210610110806.277932-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9078204ca5c33ba20443a8623a41a68a9995a70d upstream.
The clock divisor should be rounded to the closest value.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
Cc: stable@vger.kernel.org # 0e4cf69ede87 ("serial: mvebu-uart: clarify the baud rate derivation")
Link: https://lore.kernel.org/r/20210624224909.6350-2-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 5.10.43 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
[ Upstream commit e359b4411c2836cf87c8776682d1b594635570de ]
When DMA is enabled the receive handler runs in a threaded handler, but
the primary handler up until very recently neither disabled interrupts
in the device or used IRQF_ONESHOT. This would lead to a deadlock if an
interrupt comes in while the threaded receive handler is running under
the port lock.
Commit ad7676812437 ("serial: stm32: fix a deadlock condition with
wakeup event") claimed to fix an unrelated deadlock, but unfortunately
also disabled interrupts in the threaded handler. While this prevents
the deadlock mentioned in the previous paragraph it also defeats the
purpose of using a threaded handler in the first place.
Fix this by making the interrupt one-shot and not disabling interrupts
in the threaded handler.
Note that (receive) DMA must not be used for a console port as the
threaded handler could be interrupted while holding the port lock,
something which could lead to a deadlock in case an interrupt handler
ends up calling printk.
Fixes: ad7676812437 ("serial: stm32: fix a deadlock condition with wakeup event")
Fixes: 3489187204eb ("serial: stm32: adding dma support")
Cc: stable@vger.kernel.org # 4.9
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Gerald Baeza <gerald.baeza@st.com>
Reviewed-by: Valentin Caron<valentin.caron@foss.st.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210416140557.25177-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 5.10.42 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
[ Upstream commit 3890e3dea315f1a257d1b940a2a4e2fa16a7b095 ]
The macro "spi_register_driver" invokes the function
"__spi_register_driver()" which has a return type of int and can fail,
returning a negative value in such a case. This is currently ignored and
the init() function yields success even if the spi driver failed to
register.
Fix this by collecting the return value of "__spi_register_driver()" and
also unregister the uart driver in case of failure.
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Atul Gopinathan <atulgopinathan@gmail.com>
Link: https://lore.kernel.org/r/20210503115736.2104747-12-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b0a85abbe92e1a6f3e8580a4590fa7245de7090b ]
This reverts commit 51f689cc11333944c7a457f25ec75fcb41e99410.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This change did not properly unwind from the error condition, so it was
not correct.
Cc: Kangjie Lu <kjlu@umn.edu>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 016002848c82eeb5d460489ce392d91fe18c475c upstream.
In 'rp2_probe', the driver registers 'rp2_uart_interrupt' then calls
'rp2_fw_cb' through 'request_firmware_nowait'. In 'rp2_fw_cb', if the
firmware don't exists, function just return without initializing ports
of 'rp2_card'. But now the interrupt handler function has been
registered, and when an interrupt comes, 'rp2_uart_interrupt' may access
those ports then causing NULL pointer dereference or other bugs.
Because the driver does some initialization work in 'rp2_fw_cb', in
order to make the driver ready to handle interrupts, 'request_firmware'
should be used instead of asynchronous 'request_firmware_nowait'.
This report reveals it:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.19.177-gdba4159c14ef-dirty #45
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-
gc9ba5276e321-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xec/0x156 lib/dump_stack.c:118
assign_lock_key kernel/locking/lockdep.c:727 [inline]
register_lock_class+0x14e5/0x1ba0 kernel/locking/lockdep.c:753
__lock_acquire+0x187/0x3750 kernel/locking/lockdep.c:3303
lock_acquire+0x124/0x340 kernel/locking/lockdep.c:3907
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x32/0x50 kernel/locking/spinlock.c:144
spin_lock include/linux/spinlock.h:329 [inline]
rp2_ch_interrupt drivers/tty/serial/rp2.c:466 [inline]
rp2_asic_interrupt.isra.9+0x15d/0x990 drivers/tty/serial/rp2.c:493
rp2_uart_interrupt+0x49/0xe0 drivers/tty/serial/rp2.c:504
__handle_irq_event_percpu+0xfb/0x770 kernel/irq/handle.c:149
handle_irq_event_percpu+0x79/0x150 kernel/irq/handle.c:189
handle_irq_event+0xac/0x140 kernel/irq/handle.c:206
handle_fasteoi_irq+0x232/0x5c0 kernel/irq/chip.c:725
generic_handle_irq_desc include/linux/irqdesc.h:155 [inline]
handle_irq+0x230/0x3a0 arch/x86/kernel/irq_64.c:87
do_IRQ+0xa7/0x1e0 arch/x86/kernel/irq.c:247
common_interrupt+0xf/0xf arch/x86/entry/entry_64.S:670
</IRQ>
RIP: 0010:native_safe_halt+0x28/0x30 arch/x86/include/asm/irqflags.h:61
Code: 00 00 55 be 04 00 00 00 48 c7 c7 00 c2 2f 8c 48 89 e5 e8 fb 31 e7 f8
8b 05 75 af 8d 03 85 c0 7e 07 0f 00 2d 8a 61 65 00 fb f4 <5d> c3 90 90 90
90 90 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41
RSP: 0018:ffff88806b71fcc8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffde
RAX: 0000000000000000 RBX: ffffffff8bde7e48 RCX: ffffffff88a21285
RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff8c2fc200
RBP: ffff88806b71fcc8 R08: fffffbfff185f840 R09: fffffbfff185f840
R10: 0000000000000001 R11: fffffbfff185f840 R12: 0000000000000002
R13: ffffffff8bea18a0 R14: 0000000000000000 R15: 0000000000000000
arch_safe_halt arch/x86/include/asm/paravirt.h:94 [inline]
default_idle+0x6f/0x360 arch/x86/kernel/process.c:557
arch_cpu_idle+0xf/0x20 arch/x86/kernel/process.c:548
default_idle_call+0x3b/0x60 kernel/sched/idle.c:93
cpuidle_idle_call kernel/sched/idle.c:153 [inline]
do_idle+0x2ab/0x3c0 kernel/sched/idle.c:263
cpu_startup_entry+0xcb/0xe0 kernel/sched/idle.c:369
start_secondary+0x3b8/0x4e0 arch/x86/kernel/smpboot.c:271
secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:243
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
PGD 8000000056d27067 P4D 8000000056d27067 PUD 56d28067 PMD 0
Oops: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.19.177-gdba4159c14ef-dirty #45
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-
gc9ba5276e321-prebuilt.qemu.org 04/01/2014
RIP: 0010:readl arch/x86/include/asm/io.h:59 [inline]
RIP: 0010:rp2_ch_interrupt drivers/tty/serial/rp2.c:472 [inline]
RIP: 0010:rp2_asic_interrupt.isra.9+0x181/0x990 drivers/tty/serial/rp2.c:
493
Code: df e8 43 5d c2 05 48 8d 83 e8 01 00 00 48 89 85 60 ff ff ff 48 c1 e8
03 42 80 3c 30 00 0f 85 aa 07 00 00 48 8b 83 e8 01 00 00 <8b> 40 10 89 c1
89 85 68 ff ff ff 48 8b 83 e8 01 00 00 89 48 10 83
RSP: 0018:ffff88806c287cd0 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff88806ade6820 RCX: ffffffff814300b1
RDX: 1ffff1100d5bcd06 RSI: 0000000000000004 RDI: ffff88806ade6820
RBP: ffff88806c287db8 R08: ffffed100d5bcd05 R09: ffffed100d5bcd05
R10: 0000000000000001 R11: ffffed100d5bcd04 R12: ffffc90001e00000
R13: ffff888069654e10 R14: dffffc0000000000 R15: ffff888069654df0
FS: 0000000000000000(0000) GS:ffff88806c280000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000010 CR3: 000000006892c000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
rp2_uart_interrupt+0x49/0xe0 drivers/tty/serial/rp2.c:504
__handle_irq_event_percpu+0xfb/0x770 kernel/irq/handle.c:149
handle_irq_event_percpu+0x79/0x150 kernel/irq/handle.c:189
handle_irq_event+0xac/0x140 kernel/irq/handle.c:206
handle_fasteoi_irq+0x232/0x5c0 kernel/irq/chip.c:725
generic_handle_irq_desc include/linux/irqdesc.h:155 [inline]
handle_irq+0x230/0x3a0 arch/x86/kernel/irq_64.c:87
do_IRQ+0xa7/0x1e0 arch/x86/kernel/irq.c:247
common_interrupt+0xf/0xf arch/x86/entry/entry_64.S:670
</IRQ>
RIP: 0010:native_safe_halt+0x28/0x30 arch/x86/include/asm/irqflags.h:61
Code: 00 00 55 be 04 00 00 00 48 c7 c7 00 c2 2f 8c 48 89 e5 e8 fb 31 e7
f8 8b 05 75 af 8d 03 85 c0 7e 07 0f 00 2d 8a 61 65 00 fb f4 <5d> c3 90
90 90 90 90 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41
RSP: 0018:ffff88806b71fcc8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffde
RAX: 0000000000000000 RBX: ffffffff8bde7e48 RCX: ffffffff88a21285
RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff8c2fc200
RBP: ffff88806b71fcc8 R08: fffffbfff185f840 R09: fffffbfff185f840
R10: 0000000000000001 R11: fffffbfff185f840 R12: 0000000000000002
R13: ffffffff8bea18a0 R14: 0000000000000000 R15: 0000000000000000
arch_safe_halt arch/x86/include/asm/paravirt.h:94 [inline]
default_idle+0x6f/0x360 arch/x86/kernel/process.c:557
arch_cpu_idle+0xf/0x20 arch/x86/kernel/process.c:548
default_idle_call+0x3b/0x60 kernel/sched/idle.c:93
cpuidle_idle_call kernel/sched/idle.c:153 [inline]
do_idle+0x2ab/0x3c0 kernel/sched/idle.c:263
cpu_startup_entry+0xcb/0xe0 kernel/sched/idle.c:369
start_secondary+0x3b8/0x4e0 arch/x86/kernel/smpboot.c:271
secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:243
Modules linked in:
Dumping ftrace buffer:
(ftrace buffer empty)
CR2: 0000000000000010
---[ end trace 11804dbb55cb1a64 ]---
RIP: 0010:readl arch/x86/include/asm/io.h:59 [inline]
RIP: 0010:rp2_ch_interrupt drivers/tty/serial/rp2.c:472 [inline]
RIP: 0010:rp2_asic_interrupt.isra.9+0x181/0x990 drivers/tty/serial/rp2.c:
493
Code: df e8 43 5d c2 05 48 8d 83 e8 01 00 00 48 89 85 60 ff ff ff 48 c1
e8 03 42 80 3c 30 00 0f 85 aa 07 00 00 48 8b 83 e8 01 00 00 <8b> 40 10 89
c1 89 85 68 ff ff ff 48 8b 83 e8 01 00 00 89 48 10 83
RSP: 0018:ffff88806c287cd0 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff88806ade6820 RCX: ffffffff814300b1
RDX: 1ffff1100d5bcd06 RSI: 0000000000000004 RDI: ffff88806ade6820
RBP: ffff88806c287db8 R08: ffffed100d5bcd05 R09: ffffed100d5bcd05
R10: 0000000000000001 R11: ffffed100d5bcd04 R12: ffffc90001e00000
R13: ffff888069654e10 R14: dffffc0000000000 R15: ffff888069654df0
FS: 0000000000000000(0000) GS:ffff88806c280000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000010 CR3: 000000006892c000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/1621577323-1541-1-git-send-email-zheyuma97@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ea2e019c190ee3973ef7bcaf829d8762e56e635 upstream.
The Receive FIFO Data Count Trigger field (RTRG[6:0]) in the Receive
FIFO Data Count Trigger Register (HSRTRGR) of HSCIF can only hold values
ranging from 0-127. As the FIFO size is equal to 128 on HSCIF, the user
can write an out-of-range value, touching reserved bits.
Fix this by limiting the trigger value to the FIFO size minus one.
Reverse the order of the checks, to avoid rx_trig becoming zero if the
FIFO size is one.
Note that this change has no impact on other SCIF variants, as their
maximum supported trigger value is lower than the FIFO size anyway, and
the code below takes care of enforcing these limits.
Fixes: a380ed461f66d1b8 ("serial: sh-sci: implement FIFO threshold register setting")
Reported-by: Linh Phung <linh.phung.jy@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/5eff320aef92ffb33d00e57979fd3603bbb4a70f.1620648218.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ddb4ce1e6e3bd112778ab93bbd9092f23a878ec upstream.
Currently the expression lsr | UART_LSR_TEMT is always true and
this seems suspect. I believe the intent was to mask lsr with UART_LSR_TEMT
to check that bit, so the expression should be using the & operator
instead. Fix this.
Fixes: b9c2470fb150 ("serial: tegra: flush the RX fifo on frame error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210426105514.23268-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9808f9be31c68af43f6e531f2c851ebb066513fe upstream.
In commit 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support")
the way the irq gets allocated was changed. With that change the
handling FL_NOIRQ got lost. Restore the old behaviour.
Fixes: 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Link: https://lore.kernel.org/r/20210527095529.26281-1-christian.gmeiner@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e0e24208792080135248f23fdf6d51aa2e04df05 upstream.
Add support for new HPE serial device. It is MSI enabled,
but otherwise similar to legacy HP server serial devices.
Tested-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Randy Wright <rwright@hpe.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1621009614-28836-1-git-send-email-rwright@hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c35d2a960c0077a4cb09bf4989f45d289332ea0 upstream.
Add device HID AMDI0022 to the AMD UART controller driver match table
and create a platform device for it. This controller can be found on
Microsoft Surface Laptop 4 devices and seems similar enough that we can
just copy the existing AMDI0020 entries.
Cc: <stable@vger.kernel.org> # 5.10+
Tested-by: Sachi King <nakato@nakato.io>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # for 8250_dw part
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20210512210413.1982933-1-luzmaximilian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
