| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This reverts commit 99023e90fe5c147ea0665bda86764ea44f08a622.
Accidently checked this into 'net' instead of 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed the shared ei_debug variable. Replaced it by adding u32 msg_enable to
the private struct ei_device. Now each 8390 ethernet instance has a per-device
logging variable.
Changed older style printk() calls to more canonical forms.
Tested on: ne, ne2k-pci, smc-ultra, and wd hardware.
V4.0
- Substituted pr_info() and pr_debug() for printk() KERN_INFO and KERN_DEBUG
V3.0
- Checked for cases where pr_cont() was most appropriate choice.
- Changed module parameter from 'debug' to 'msg_enable' because debug was
no longer the best description.
V2.0
- Changed netif_msg_(drv|probe|ifdown|rx_err|tx_err|tx_queued|intr|rx_status|hw)
to netif_(dbg|info|warn|err) where possible.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_partial_csum_set requires that the linear area of the skb covers the
checksum field. The checksum setup code in netback was only doing that
pullup in the case when the pseudo header checksum was being recalculated
though. This patch makes that pullup unconditional. (I pullup the whole
transport header just for simplicity; the requirement is only for the check
field but in the case of UDP this is the last field in the header and in the
case of TCP it's the last but one).
The lack of pullup manifested as failures running Microsoft HCK network
tests on a pair of Windows 8 VMs and it has been verified that this patch
fixes the problem.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some I2C bus drivers do not allow zero-length data transfers which are
required to start a measurement with the HIH6130/1 sensor. Nevertheless,
we can overcome this limitation by writing a zero dummy byte. This byte
is ignored by the sensor and was verified to be working with the OMAP
I2C bus driver in a BeagleBone board.
Signed-off-by: José Miguel Gonçalves <jose.goncalves@inov.pt>
[Guenter Roeck: Simplified complexity of write_length initialization]
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit 89ce376c6bdc (drivers/net: Use of_match_ptr() macro in smc91x.c)
added minimal device tree support to smc91x, but it's not working on
many platforms because of the lack of some key configuration bits.
Fix the issue by parsing the necessary configuration like the
smc911x driver is doing. As most smc91x users seem to use 16-bit
access, let's default to that if no reg-io-width is specified.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
macvtap_put_user() never return a value grater than iov length, this in fact
bypasses the truncated checking in macvtap_recvmsg(). Fix this by always
returning the size of packet plus the possible vlan header to let the trunca
checking work.
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 6680ec68eff47d36f67b4351bc9836fd6cba9532
(tuntap: hardware vlan tx support) breaks the truncated packet signal by nev
return a length greater than iov length in tun_put_user(). This patch fixes
by always return the length of packet plus possible vlan header. Caller can
detect the truncated packet by comparing the return value and the size of io
length.
Cc: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Renesas R-Car development boards use KSZ8041RNLI PHY which for some reason has
ID of 0x00221537 that is not documented for KSZ8041-family PHYs and does not
match the documented ID of 0x0022151x (where 'x' is the revision). We have
to add the new #define PHY_ID_* and new ksphy_driver[] entry, almost the same
as KSZ8041 one, differing only in the 'phy_id' and 'name' fields.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
The new tg3 driver leaves REG_BASE_ADDR (PCI config offset 120)
uninitialized. From power on reset this register may have garbage in it. The
Register Base Address register defines the device local address of a
register. The data pointed to by this location is read or written using
the Register Data register (PCI config offset 128). When REG_BASE_ADDR has
garbage any read or write of Register Data Register (PCI 128) will cause the
PCI bus to lock up. The TCO watchdog will fire and bring down the system.
Signed-off-by: Nat Gurumoorthy <natg@google.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jason Wang and Michael S. Tsirkin are still discussing how
to properly fix this.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
macvtap_put_user() never return a value grater than iov length, this in fact
bypasses the truncated checking in macvtap_recvmsg(). Fix this by always
returning the size of packet plus the possible vlan header to let the truncated
checking work.
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 6680ec68eff47d36f67b4351bc9836fd6cba9532
(tuntap: hardware vlan tx support) breaks the truncated packet signal by never
return a length greater than iov length in tun_put_user(). This patch fixes this
by always return the length of packet plus possible vlan header. Caller can
detect the truncated packet by comparing the return value and the size of iov
length.
Reported-by: Vlad Yasevich <vyasevich@gmail.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise causing dst memory leakage.
Have Checked all other type tunnel device transmit implementation,
no such things happens anymore.
Signed-off-by: Fan Du <fan.du@windriver.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ben Hutchings says:
====================
Several fixes for the PTP hardware support added in 3.7:
1. Fix filtering of PTP packets on the TX path to be robust against bad
header lengths.
2. Limit logging on the RX path in case of a PTP packet flood, partly
from Laurence Evans.
3. Disable PTP hardware when the interface is down so that we don't
receive RX timestamp events, from Alexandre Rames.
4. Maintain clock frequency adjustment when a time offset is applied.
Also fixes for the SFC9100 family support added in 3.12:
5. Take the RX prefix length into account when applying NET_IP_ALIGN,
from Andrew Rybchenko.
6. Work around a bug that breaks communication between the driver and
firmware, from Robert Stonehouse.
Please also queue these up for the appropriate stable branches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The module parameter stats_current_allocated_bytes in dm-mod is
read-only. This parameter informs the user about memory
consumption. It is not supposed to be changed by the user.
However, despite being read-only, this parameter can be set on
modprobe or insmod command line:
modprobe dm-mod stats_current_allocated_bytes=12345
The kernel doesn't expect that this variable can be non-zero at module
initialization and if the user sets it, it results in warning.
This patch initializes the variable in the module init routine, so
that user-supplied value is ignored.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
|
|
Some module parameters in dm-bufio are read-only. These parameters
inform the user about memory consumption. They are not supposed to be
changed by the user.
However, despite being read-only, these parameters can be set on
modprobe or insmod command line, for example:
modprobe dm-bufio current_allocated_bytes=12345
The kernel doesn't expect that these variables can be non-zero at module
initialization and if the user sets them, it results in BUG.
This patch initializes the variables in the module init routine, so that
user-supplied values are ignored.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.2+
|
|
The sun4i-emac driver uses devm_request_irq at .ndo_open time, but relies on
the managed device mechanism to actually free it. This causes an issue whenever
someone wants to restart the interface, the interrupt still being held, and not
yet released.
Fall back to using the regular request_irq at .ndo_open time, and introduce a
free_irq during .ndo_stop.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f494a9c6b1b6dd9a9f21bbb75d9210d478eeb498 ("dm cache: cache
shrinking support") broke cache resizing support.
dm_cache_resize() is called with cache->cache_size before it gets
updated to new_size, so it is a no-op. But the dm-cache superblock is
updated with the new_size even though the backing dm-array is not
resized. Fix this by passing the new_size to dm_cache_resize().
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Micro benchmarks that repeatedly issued IO to a single block were
failing to cause a promotion from the origin device to the cache. Fix
this by not updating the stats during map() if -EWOULDBLOCK will be
returned.
The mq policy will only update stats, consider migration, etc, once per
tick period (a unit of time established between dm-cache core and the
policies).
When the IO thread calls the policy's map method, if it would like to
migrate the associated block it returns -EWOULDBLOCK, the IO then gets
handed over to a worker thread which handles the migration. The worker
thread calls map again, to check the migration is still needed (avoids a
race among other things). *BUT*, before this fix, if we were still in
the same tick period the stats were already updated by the previous map
call -- so the migration would no longer be requested.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
A thin-pool may be in read-only mode because the pool's data or metadata
space was exhausted. To allow for recovery, by adding more space to the
pool, we must allow a pool to transition from PM_READ_ONLY to PM_WRITE
mode. Otherwise, running out of space will render the pool permanently
read-only.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
If the thin-pool transitioned to fail mode and the thin-pool's table
were reloaded for some reason: the new table's default pool mode would
be read-write, though it will transition to fail mode during resume.
When the pool mode transitions directly from PM_WRITE to PM_FAIL we need
to re-establish the intermediate read-only state in both the metadata
and persistent-data block manager (as is usually done with the normal
pool mode transition sequence: PM_WRITE -> PM_READ_ONLY -> PM_FAIL).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
Rename commit_or_fallback() to commit(). Now all previous calls to
commit() will trigger the pool mode to fallback if the commit fails.
Also, check the error returned from commit() in alloc_data_block().
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
Switch the thin pool to read-only mode in alloc_data_block() if
dm_pool_alloc_data_block() fails because the pool's metadata space is
exhausted.
Differentiate between data and metadata space in messages about no
free space available.
This issue was noticed with the device-mapper-test-suite using:
dmtest run --suite thin-provisioning -n /exhausting_metadata_space_causes_fail_mode/
The quantity of errors logged in this case must be reduced.
before patch:
device-mapper: thin: 253:4: reached low water mark for metadata device: sending event.
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
<snip ... these repeat for a _very_ long while ... >
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: 253:4: commit failed: error = -28
device-mapper: thin: 253:4: switching pool to read-only mode
after patch:
device-mapper: thin: 253:4: reached low water mark for metadata device: sending event.
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: 253:4: no free metadata space available.
device-mapper: thin: 253:4: switching pool to read-only mode
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org
|
|
Switch the thin pool to read-only mode when dm_thin_insert_block() fails
since there is little reason to expect the cause of the failure to be
resolved without further action by user space.
This issue was noticed with the device-mapper-test-suite using:
dmtest run --suite thin-provisioning -n /exhausting_metadata_space_causes_fail_mode/
The quantity of errors logged in this case must be reduced.
before patch:
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
<snip ... these repeat for a long while ... >
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: thin: 253:4: no free metadata space available.
device-mapper: thin: 253:4: switching pool to read-only mode
after patch:
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: 253:4: dm_thin_insert_block() failed: error = -28
device-mapper: thin: 253:4: switching pool to read-only mode
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
Commit 2fc48021f4afdd109b9e52b6eef5db89ca80bac7 ("dm persistent
metadata: add space map threshold callback") introduced a regression
to the metadata block allocation path that resulted in errors being
ignored. This regression was uncovered by running the following
device-mapper-test-suite test:
dmtest run --suite thin-provisioning -n /exhausting_metadata_space_causes_fail_mode/
The ignored error codes in sm_metadata_new_block() could crash the
kernel through use of either the dm-thin or dm-cache targets, e.g.:
device-mapper: thin: 253:4: reached low water mark for metadata device: sending event.
device-mapper: space map metadata: unable to allocate new metadata block
general protection fault: 0000 [#1] SMP
...
Workqueue: dm-thin do_worker [dm_thin_pool]
task: ffff880035ce2ab0 ti: ffff88021a054000 task.ti: ffff88021a054000
RIP: 0010:[<ffffffffa0331385>] [<ffffffffa0331385>] metadata_ll_load_ie+0x15/0x30 [dm_persistent_data]
RSP: 0018:ffff88021a055a68 EFLAGS: 00010202
RAX: 003fc8243d212ba0 RBX: ffff88021a780070 RCX: ffff88021a055a78
RDX: ffff88021a055a78 RSI: 0040402222a92a80 RDI: ffff88021a780070
RBP: ffff88021a055a68 R08: ffff88021a055ba4 R09: 0000000000000010
R10: 0000000000000000 R11: 00000002a02e1000 R12: ffff88021a055ad4
R13: 0000000000000598 R14: ffffffffa0338470 R15: ffff88021a055ba4
FS: 0000000000000000(0000) GS:ffff88033fca0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007f467c0291b8 CR3: 0000000001a0b000 CR4: 00000000000007e0
Stack:
ffff88021a055ab8 ffffffffa0332020 ffff88021a055b30 0000000000000001
ffff88021a055b30 0000000000000000 ffff88021a055b18 0000000000000000
ffff88021a055ba4 ffff88021a055b98 ffff88021a055ae8 ffffffffa033304c
Call Trace:
[<ffffffffa0332020>] sm_ll_lookup_bitmap+0x40/0xa0 [dm_persistent_data]
[<ffffffffa033304c>] sm_metadata_count_is_more_than_one+0x8c/0xc0 [dm_persistent_data]
[<ffffffffa0333825>] dm_tm_shadow_block+0x65/0x110 [dm_persistent_data]
[<ffffffffa0331b00>] sm_ll_mutate+0x80/0x300 [dm_persistent_data]
[<ffffffffa0330e60>] ? set_ref_count+0x10/0x10 [dm_persistent_data]
[<ffffffffa0331dba>] sm_ll_inc+0x1a/0x20 [dm_persistent_data]
[<ffffffffa0332270>] sm_disk_new_block+0x60/0x80 [dm_persistent_data]
[<ffffffff81520036>] ? down_write+0x16/0x40
[<ffffffffa001e5c4>] dm_pool_alloc_data_block+0x54/0x80 [dm_thin_pool]
[<ffffffffa001b23c>] alloc_data_block+0x9c/0x130 [dm_thin_pool]
[<ffffffffa001c27e>] provision_block+0x4e/0x180 [dm_thin_pool]
[<ffffffffa001fe9a>] ? dm_thin_find_block+0x6a/0x110 [dm_thin_pool]
[<ffffffffa001c57a>] process_bio+0x1ca/0x1f0 [dm_thin_pool]
[<ffffffff8111e2ed>] ? mempool_free+0x8d/0xa0
[<ffffffffa001d755>] process_deferred_bios+0xc5/0x230 [dm_thin_pool]
[<ffffffffa001d911>] do_worker+0x51/0x60 [dm_thin_pool]
[<ffffffff81067872>] process_one_work+0x182/0x3b0
[<ffffffff81068c90>] worker_thread+0x120/0x3a0
[<ffffffff81068b70>] ? manage_workers+0x160/0x160
[<ffffffff8106eb2e>] kthread+0xce/0xe0
[<ffffffff8106ea60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff8152af6c>] ret_from_fork+0x7c/0xb0
[<ffffffff8106ea60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff8152af6c>] ret_from_fork+0x7c/0xb0
[<ffffffff8106ea60>] ? kthread_freezable_should_stop+0x70/0x70
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org # v3.10+
|
|
The dm_round_up function may overflow to zero. In this case,
dm_table_create() must fail rather than go on to allocate an empty array
with alloc_targets().
This fixes a possible memory corruption that could be caused by passing
too large a number in "param->target_count".
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
There is a possible leak of snapshot space in case of crash.
The reason for space leaking is that chunks in the snapshot device are
allocated sequentially, but they are finished (and stored in the metadata)
out of order, depending on the order in which copying finished.
For example, supposed that the metadata contains the following records
SUPERBLOCK
METADATA (blocks 0 ... 250)
DATA 0
DATA 1
DATA 2
...
DATA 250
Now suppose that you allocate 10 new data blocks 251-260. Suppose that
copying of these blocks finish out of order (block 260 finished first
and the block 251 finished last). Now, the snapshot device looks like
this:
SUPERBLOCK
METADATA (blocks 0 ... 250, 260, 259, 258, 257, 256)
DATA 0
DATA 1
DATA 2
...
DATA 250
DATA 251
DATA 252
DATA 253
DATA 254
DATA 255
METADATA (blocks 255, 254, 253, 252, 251)
DATA 256
DATA 257
DATA 258
DATA 259
DATA 260
Now, if the machine crashes after writing the first metadata block but
before writing the second metadata block, the space for areas DATA 250-255
is leaked, it contains no valid data and it will never be used in the
future.
This patch makes dm-snapshot complete exceptions in the same order they
were allocated, thus fixing this bug.
Note: when backporting this patch to the stable kernel, change the version
field in the following way:
* if version in the stable kernel is {1, 11, 1}, change it to {1, 12, 0}
* if version in the stable kernel is {1, 10, 0} or {1, 10, 1}, change it
to {1, 10, 2}
Userspace reads the version to determine if the bug was fixed, so the
version change is needed.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
git://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull clockevents/clocksource fixes from Daniel Lezcano:
* Axel Lin added a missing dependency on CLKSRC_MMIO in the Kconfig
for the time-efm32
* Dinh Nguyen fixed read_sched_clock to return the right value and
added the clksrc-of missing definition for the dw_apb_timer
* Ezequiel Garcia registered the sched clock after the counter,
thus preventing time jump in the traces for the armada-370-xp
* Marc Zyngier stopped the timer before enabling the irq in order
to prevent it to be fired before the clockevent is registered for
the sunxi
* Thierry Reding removed a of_node_put in clksrc-of because the
reference is not held
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull watchdog fixes from Wim Van Sebroeck:
"Drop the unnecessary miscdevice.h includes that we forgot in commit
487722cf2d66 ("watchdog: Get rid of MODULE_ALIAS_MISCDEV statements")
and fix an oops for the sc1200_wdt driver"
* git://www.linux-watchdog.org/linux-watchdog:
sc1200_wdt: Fix oops
watchdog: Drop unnecessary include of miscdevice.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32
Pull AVR32 fixes from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: favr-32: clk_round_rate() can return a zero upon error
avr32: remove deprecated IRQF_DISABLED
cpufreq_ at32ap-cpufreq.c: Fix section mismatch
avr32: pm: Fix section mismatch
avr32: Kill CONFIG_MTD_PARTITIONS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"One patch to increase the number of possible CPUs to 256, with the
latest machine a single LPAR can have up to 101 CPUs. Plus a number
of bug fixes, the clock_gettime patch fixes a regression added in the
3.13 merge window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/time,vdso: fix clock_gettime for CLOCK_MONOTONIC
s390/vdso: ectg gettime support for CLOCK_THREAD_CPUTIME_ID
s390/vdso: fix access-list entry initialization
s390: increase CONFIG_NR_CPUS limit
s390/smp,sclp: fix size of sclp_cpu_info structure
s390/sclp: replace uninitialized early_event_mask_sccb variable with sccb_early
s390/dasd: fix memory leak caused by dangling references to request_queue
|
|
In commit 620f5e1cbf (dts: Rename DW APB timer compatible strings), both
"snps,dw-apb-timer-sp" and "snps,dw-apb-timer-osc" were deprecated in place
of "snps,dw-apb-timer". But the driver also needs to be udpated in order to
support this new binding "snps,dw-apb-timer".
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The read_sched_clock should return the ~value because the clock is a
countdown implementation. read_sched_clock() should be the same as
__apbt_read_clocksource().
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The sun4i timer can still be ticking when we enable the interrupt.
If another timer is actually used (A7 architected timer, for example),
odds are that the interrupt will eventually fire with the event_handler
pointer being NULL.
The obvious fix it to stop the timer before registering the interrupt.
Observed and tested on sun7i (cubietruck).
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
When booting a recent kernel on ARM with OF_DYNAMIC enabled, the kernel
warns about the following:
[ 0.000000] ERROR: Bad of_node_put() on /timer@50004600
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.12.0-rc5-next-20131017-00077-gedfd827-dirty #406
[ 0.000000] [<c0015b68>] (unwind_backtrace+0x0/0xf4) from [<c00117e4>] (show_stack+0x10/0x14)
[ 0.000000] [<c00117e4>] (show_stack+0x10/0x14) from [<c055f734>] (dump_stack+0x9c/0xc8)
[ 0.000000] [<c055f734>] (dump_stack+0x9c/0xc8) from [<c03b47d4>] (of_node_release+0x90/0x9c)
[ 0.000000] [<c03b47d4>] (of_node_release+0x90/0x9c) from [<c03b5084>] (of_find_matching_node_and_match+0x78/0xb4)
[ 0.000000] [<c03b5084>] (of_find_matching_node_and_match+0x78/0xb4) from [<c07887c8>] (clocksource_of_init+0x60/0x70)
[ 0.000000] [<c07887c8>] (clocksource_of_init+0x60/0x70) from [<c076e99c>] (start_kernel+0x1f4/0x33c)
[ 0.000000] [<c076e99c>] (start_kernel+0x1f4/0x33c) from [<80008074>] (0x80008074)
This is caused by clocksource_of_init() dropping a reference on the
device node that it never took. The reference taken by the loop is
implicitly dropped on subsequent iterations. See the implementation of
and the comment on top of the of_find_matching_node_and_match()
function for reference (no pun intended).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
This commit registers the sched_clock _after_ the counter reset
(instead of before). This removes the timestamp 'jump' in kernel
log messages.
Before this change:
[ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798691800ns
[ 0.000000] Initializing Coherency fabric
[ 0.000000] Aurora cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x00000100, AUX_CTRL 0x1a696b12, Cache size: 1024 kB
[ 163.507447] Calibrating delay loop... 1325.05 BogoMIPS (lpj=662528)
[ 163.521419] pid_max: default: 32768 minimum: 301
[ 163.526185] Mount-cache hash table entries: 512
[ 163.531095] CPU: Testing write buffer coherency: ok
After this change:
[ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798691800ns
[ 0.000000] Initializing Coherency fabric
[ 0.000000] Aurora cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x00000100, AUX_CTRL 0x1a696b12, Cache size: 1024 kB
[ 0.016849] Calibrating delay loop... 1325.05 BogoMIPS (lpj=662528)
[ 0.030820] pid_max: default: 32768 minimum: 301
[ 0.035588] Mount-cache hash table entries: 512
[ 0.040500] CPU: Testing write buffer coherency: ok
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
|
|
The time-efm32 driver uses the clocksource MMIO functions.
Thus it needs to select CLKSRC_MMIO in Kconfig.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
Commit 0b2aa8be introduced a regression that causes failure
in setting LED GPO direction to OUT.
This causes USB host probe failures for Beagleboard C4.
platform usb_phy_gen_xceiv.2: Driver usb_phy_gen_xceiv requests probe deferral
hsusb2_vcc: Failed to request enable GPIO510: -22
reg-fixed-voltage reg-fixed-voltage.0.auto: Failed to register regulator: -22
reg-fixed-voltage: probe of reg-fixed-voltage.0.auto failed with error -22
direction_out/direction_in must return 0 if the operation succeeded.
Also, don't update direction flag and output data if twl4030_set_gpio_direction()
failed inside twl_direction_out();
Cc: stable@vger.kernel.org
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 7cbb0e55e27e ("sh-pfc: Don't duplicate argument to PINMUX_GPIO
macro") erronesouly modified the PINMUX_GPIO macro in a way that
resulted in all pins being named "name". Fix the macro to name the pins
correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If loaded with isapnp = 0 the driver explodes. This is catching
people out now and then. What should happen in the working case is
a complete mystery and the code appears terminally confused, but we
can at least make the error path work properly.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Partially-Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=53991
|
|
After commit 487722cf2 (watchdog: Get rid of MODULE_ALIAS_MISCDEV
statements) the affected drivers no longer need to include miscdevice.h.
Only exception is rt2880_wdt.c which never needed it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The function at32_cpufreq_driver_init was marked as __init but will be
called from inside the cpufreq framework. This lead to the following a
section mismatch during compilation:
WARNING: drivers/built-in.o(.data+0x2448): Section mismatch in reference
from the variable at32_driver to the function
.init.text:at32_cpufreq_driver_init()
The variable at32_driver references
the function __init at32_cpufreq_driver_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Fix the return when 'buf->pages' allocation error.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
|
|
Commit dc77523c5da5513df1bbc74db2a522a94f4cec0e ensured that m.offset is
only set for the MMAP memory mode by calling __setup_offsets only for that
mode.
However, __setup_offsets also initializes the length fields, and that should
be done regardless of the memory mode. Because of that change the v4l2-ctl
test application fails for the USERPTR mode.
This fix creates a __setup_lengths function that sets the length, and
__setup_offsets just sets the offset and no longer touches the length.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Coverity report pointet out by Dmitry
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Restore previous layout of sysfs attributes that was broken by commit
3778a2129bcce84f684cc0017ed20d2524afd289 (input: serio: remove bus usage of
dev_attrs) which moved all serio device attributes into 'id' group, when
only 'type', 'proto', 'id', and 'extra' should be in 'id' group and the
rest of attributes should be attached directly to the device.
Reported-by: Thomas Hellstrom <thellstrom@vmware.com>
Tested-by: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Merging with the mainline to sync up on changes to serio core.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a handful of powerpc fixes for 3.13.
The patches are reasonably trivial and self contained. Note the offb
patches outside of arch/powerpc, they are LE fixes for our
open-firmware 'dumb' framebuffer"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix up the kdump base cap to 128M
powernv: Fix VFIO support with PHB3
powerpc/52xx: Re-enable bestcomm driver in defconfigs
powerpc/pasemi: Turn on devtmpfs in defconfig
offb: Add palette hack for little endian
offb: Little endian fixes
powerpc: Fix PTE page address mismatch in pgtable ctor/dtor
powerpc/44x: Fix ocm_block allocation
powerpc: Fix build break with PPC_EARLY_DEBUG_BOOTX=y
powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node
|
|
This patch adds barriers at appropriate places to ensure the driver
works on Xilinx Zynq ARM-based SoC platform.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
