summaryrefslogtreecommitdiff
path: root/include/linux/if_bridge.h
AgeCommit message (Collapse)AuthorFilesLines
2021-08-04net: make switchdev_bridge_port_{,unoffload} loosely coupled with the bridgeVladimir Oltean1-35/+0
With the introduction of explicit offloading API in switchdev in commit 2f5dc00f7a3e ("net: bridge: switchdev: let drivers inform which bridge ports are offloaded"), we started having Ethernet switch drivers calling directly into a function exported by net/bridge/br_switchdev.c, which is a function exported by the bridge driver. This means that drivers that did not have an explicit dependency on the bridge before, like cpsw and am65-cpsw, now do - otherwise it is not possible to call a symbol exported by a driver that can be built as module unless you are a module too. There was an attempt to solve the dependency issue in the form of commit b0e81817629a ("net: build all switchdev drivers as modules when the bridge is a module"). Grygorii Strashko, however, says about it: | In my opinion, the problem is a bit bigger here than just fixing the | build :( | | In case, of ^cpsw the switchdev mode is kinda optional and in many | cases (especially for testing purposes, NFS) the multi-mac mode is | still preferable mode. | | There were no such tight dependency between switchdev drivers and | bridge core before and switchdev serviced as independent, notification | based layer between them, so ^cpsw still can be "Y" and bridge can be | "M". Now for mostly every kernel build configuration the CONFIG_BRIDGE | will need to be set as "Y", or we will have to update drivers to | support build with BRIDGE=n and maintain separate builds for | networking vs non-networking testing. But is this enough? Wouldn't | it cause 'chain reaction' required to add more and more "Y" options | (like CONFIG_VLAN_8021Q)? | | PS. Just to be sure we on the same page - ARM builds will be forced | (with this patch) to have CONFIG_TI_CPSW_SWITCHDEV=m and so all our | automation testing will just fail with omap2plus_defconfig. In the light of this, it would be desirable for some configurations to avoid dependencies between switchdev drivers and the bridge, and have the switchdev mode as completely optional within the driver. Arnd Bergmann also tried to write a patch which better expressed the build time dependency for Ethernet switch drivers where the switchdev support is optional, like cpsw/am65-cpsw, and this made the drivers follow the bridge (compile as module if the bridge is a module) only if the optional switchdev support in the driver was enabled in the first place: https://patchwork.kernel.org/project/netdevbpf/patch/20210802144813.1152762-1-arnd@kernel.org/ but this still did not solve the fact that cpsw and am65-cpsw now must be built as modules when the bridge is a module - it just expressed correctly that optional dependency. But the new behavior is an apparent regression from Grygorii's perspective. So to support the use case where the Ethernet driver is built-in, NET_SWITCHDEV (a bool option) is enabled, and the bridge is a module, we need a framework that can handle the possible absence of the bridge from the running system, i.e. runtime bloatware as opposed to build-time bloatware. Luckily we already have this framework, since switchdev has been using it extensively. Events from the bridge side are transmitted to the driver side using notifier chains - this was originally done so that unrelated drivers could snoop for events emitted by the bridge towards ports that are implemented by other drivers (think of a switch driver with LAG offload that listens for switchdev events on a bonding/team interface that it offloads). There are also events which are transmitted from the driver side to the bridge side, which again are modeled using notifiers. SWITCHDEV_FDB_ADD_TO_BRIDGE is an example of this, and deals with notifying the bridge that a MAC address has been dynamically learned. So there is a precedent we can use for modeling the new framework. The difference compared to SWITCHDEV_FDB_ADD_TO_BRIDGE is that the work that the bridge needs to do when a port becomes offloaded is blocking in its nature: replay VLANs, MDBs etc. The calling context is indeed blocking (we are under rtnl_mutex), but the existing switchdev notification chain that the bridge is subscribed to is only the atomic one. So we need to subscribe the bridge to the blocking switchdev notification chain too. This patch: - keeps the driver-side perception of the switchdev_bridge_port_{,un}offload unchanged - moves the implementation of switchdev_bridge_port_{,un}offload from the bridge module into the switchdev module. - makes everybody that is subscribed to the switchdev blocking notifier chain "hear" offload & unoffload events - makes the bridge driver subscribe and handle those events - moves the bridge driver's handling of those events into 2 new functions called br_switchdev_port_{,un}offload. These functions contain in fact the core of the logic that was previously in switchdev_bridge_port_{,un}offload, just that now we go through an extra indirection layer to reach them. Unlike all the other switchdev notification structures, the structure used to carry the bridge port information, struct switchdev_notifier_brport_info, does not contain a "bool handled". This is because in the current usage pattern, we always know that a switchdev bridge port offloading event will be handled by the bridge, because the switchdev_bridge_port_offload() call was initiated by a NETDEV_CHANGEUPPER event in the first place, where info->upper_dev is a bridge. So if the bridge wasn't loaded, then the CHANGEUPPER event couldn't have happened. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27net: bridge: move bridge ioctls out of .ndo_do_ioctlArnd Bergmann1-1/+6
Working towards obsoleting the .ndo_do_ioctl operation entirely, stop passing the SIOCBRADDIF/SIOCBRDELIF device ioctl commands into this callback. My first attempt was to add another ndo_siocbr() callback, but as there is only a single driver that takes these commands and there is already a hook mechanism to call directly into this driver, extend this hook instead, and use it for both the deviceless and the device specific ioctl commands. Cc: Roopa Prabhu <roopa@nvidia.com> Cc: Nikolay Aleksandrov <nikolay@nvidia.com> Cc: bridge@lists.linux-foundation.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27net: bridge: add a helper for retrieving port VLANs from the data pathVladimir Oltean1-0/+8
Introduce a brother of br_vlan_get_info() which is protected by the RCU mechanism, as opposed to br_vlan_get_info() which relies on taking the write-side rtnl_mutex. This is needed for drivers which need to find out whether a bridge port has a VLAN configured or not. For example, certain DSA switches might not offer complete source port identification to the CPU on RX, just the VLAN in which the packet was received. Based on this VLAN, we cannot set an accurate skb->dev ingress port, but at least we can configure one that behaves the same as the correct one would (this is possible because DSA sets skb->offload_fwd_mark = 1). When we look at the bridge RX handler (br_handle_frame), we see that what matters regarding skb->dev is the VLAN ID and the port STP state. So we need to select an skb->dev that has the same bridge VLAN as the packet we're receiving, and is in the LEARNING or FORWARDING STP state. The latter is easy, but for the former, we should somehow keep a shadow list of the bridge VLANs on each port, and a lookup table between VLAN ID and the 'designated port for imprecise RX'. That is rather complicated to keep in sync properly (the designated port per VLAN needs to be updated on the addition and removal of a VLAN, as well as on the join/leave events of the bridge on that port). So, to avoid all that complexity, let's just iterate through our finite number of ports and ask the bridge, for each packet: "do you have this VLAN configured on this port?". Cc: Roopa Prabhu <roopa@nvidia.com> Cc: Nikolay Aleksandrov <nikolay@nvidia.com> Cc: Ido Schimmel <idosch@nvidia.com> Cc: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23net: bridge: switchdev: allow the TX data plane forwarding to be offloadedTobias Waldekranz1-0/+3
Allow switchdevs to forward frames from the CPU in accordance with the bridge configuration in the same way as is done between bridge ports. This means that the bridge will only send a single skb towards one of the ports under the switchdev's control, and expects the driver to deliver the packet to all eligible ports in its domain. Primarily this improves the performance of multicast flows with multiple subscribers, as it allows the hardware to perform the frame replication. The basic flow between the driver and the bridge is as follows: - When joining a bridge port, the switchdev driver calls switchdev_bridge_port_offload() with tx_fwd_offload = true. - The bridge sends offloadable skbs to one of the ports under the switchdev's control using skb->offload_fwd_mark = true. - The switchdev driver checks the skb->offload_fwd_mark field and lets its FDB lookup select the destination port mask for this packet. v1->v2: - convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long - introduce a static key "br_switchdev_fwd_offload_used" to minimize the impact of the newly introduced feature on all the setups which don't have hardware that can make use of it - introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache line access - reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in __br_forward() - do not strip VLAN on egress if forwarding offload on VLAN-aware bridge is being used - propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP v2->v3: - replace the solution based on .ndo_dfwd_add_station with a solution based on switchdev_bridge_port_offload - rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD v3->v4: rebase v4->v5: - make sure the static key is decremented on bridge port unoffload - more function and variable renaming and comments for them: br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload fwd_accel to tx_fwd_offload Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22net: bridge: move the switchdev object replay helpers to "push" modeVladimir Oltean1-36/+18
Starting with commit 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries"), DSA has introduced some bridge helpers that replay switchdev events (FDB/MDB/VLAN additions and deletions) that can be lost by the switchdev drivers in a variety of circumstances: - an IP multicast group was host-joined on the bridge itself before any switchdev port joined the bridge, leading to the host MDB entries missing in the hardware database. - during the bridge creation process, the MAC address of the bridge was added to the FDB as an entry pointing towards the bridge device itself, but with no switchdev ports being part of the bridge yet, this local FDB entry would remain unknown to the switchdev hardware database. - a VLAN/FDB/MDB was added to a bridge port that is a LAG interface, before any switchdev port joined that LAG, leading to the hardware database missing those entries. - a switchdev port left a LAG that is a bridge port, while the LAG remained part of the bridge, and all FDB/MDB/VLAN entries remained installed in the hardware database of the switchdev port. Also, since commit 0d2cfbd41c4a ("net: bridge: ignore switchdev events for LAG ports which didn't request replay"), DSA introduced a method, based on a const void *ctx, to ensure that two switchdev ports under the same LAG that is a bridge port do not see the same MDB/VLAN entry being replayed twice by the bridge, once for every bridge port that joins the LAG. With so many ordering corner cases being possible, it seems unreasonable to expect a switchdev driver writer to get it right from the first try. Therefore, now that DSA has experimented with the bridge replay helpers for a little bit, we can move the code to the bridge driver where it is more readily available to all switchdev drivers. To convert the switchdev object replay helpers from "pull mode" (where the driver asks for them) to a "push mode" (where the bridge offers them automatically), the biggest problem is that the bridge needs to be aware when a switchdev port joins and leaves, even when the switchdev is only indirectly a bridge port (for example when the bridge port is a LAG upper of the switchdev). Luckily, we already have a hook for that, in the form of the newly introduced switchdev_bridge_port_offload() and switchdev_bridge_port_unoffload() calls. These offer a natural place for hooking the object addition and deletion replays. Extend the above 2 functions with: - pointers to the switchdev atomic notifier (for FDB replays) and the blocking notifier (for MDB and VLAN replays). - the "const void *ctx" argument required for drivers to be able to disambiguate between which port is targeted, when multiple ports are lowers of the same LAG that is a bridge port. Most of the drivers pass NULL to this argument, except the ones that support LAG offload and have the proper context check already in place in the switchdev blocking notifier handler. Also unexport the replay helpers, since nobody except the bridge calls them directly now. Note that: (a) we abuse the terminology slightly, because FDB entries are not "switchdev objects", but we count them as objects nonetheless. With no direct way to prove it, I think they are not modeled as switchdev objects because those can only be installed by the bridge to the hardware (as opposed to FDB entries which can be propagated in the other direction too). This is merely an abuse of terms, FDB entries are replayed too, despite not being objects. (b) the bridge does not attempt to sync port attributes to newly joined ports, just the countable stuff (the objects). The reason for this is simple: no universal and symmetric way to sync and unsync them is known. For example, VLAN filtering: what to do on unsync, disable or leave it enabled? Similarly, STP state, ageing timer, etc etc. What a switchdev port does when it becomes standalone again is not really up to the bridge's competence, and the driver should deal with it. On the other hand, replaying deletions of switchdev objects can be seen a matter of cleanup and therefore be treated by the bridge, hence this patch. We make the replay helpers opt-in for drivers, because they might not bring immediate benefits for them: - nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(), so br_vlan_replay() should not do anything for the new drivers on which we call it. The existing drivers where there was even a slight possibility for there to exist a VLAN on a bridge port before they join it are already guarded against this: mlxsw and prestera deny joining LAG interfaces that are members of a bridge. - br_fdb_replay() should now notify of local FDB entries, but I patched all drivers except DSA to ignore these new entries in commit 2c4eca3ef716 ("net: bridge: switchdev: include local flag in FDB notifications"). Driver authors can lift this restriction as they wish, and when they do, they can also opt into the FDB replay functionality. - br_mdb_replay() should fix a real issue which is described in commit 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries"). However most drivers do not offload the SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw offload this switchdev object, and I don't completely understand the way in which they offload this switchdev object anyway. So I'll leave it up to these drivers' respective maintainers to opt into br_mdb_replay(). So most of the drivers pass NULL notifier blocks for the replay helpers, except: - dpaa2-switch which was already acked/regression-tested with the helpers enabled (and there isn't much of a downside in having them) - ocelot which already had replay logic in "pull" mode - DSA which already had replay logic in "pull" mode An important observation is that the drivers which don't currently request bridge event replays don't even have the switchdev_bridge_port_{offload,unoffload} calls placed in proper places right now. This was done to avoid unnecessary rework for drivers which might never even add support for this. For driver writers who wish to add replay support, this can be used as a tentative placement guide: https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/ Cc: Vadym Kochan <vkochan@marvell.com> Cc: Taras Chornyi <tchornyi@marvell.com> Cc: Ioana Ciornei <ioana.ciornei@nxp.com> Cc: Lars Povlsen <lars.povlsen@microchip.com> Cc: Steen Hegelund <Steen.Hegelund@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22net: bridge: switchdev: let drivers inform which bridge ports are offloadedVladimir Oltean1-0/+21
On reception of an skb, the bridge checks if it was marked as 'already forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it is, it assigns the source hardware domain of that skb based on the hardware domain of the ingress port. Then during forwarding, it enforces that the egress port must have a different hardware domain than the ingress one (this is done in nbp_switchdev_allowed_egress). Non-switchdev drivers don't report any physical switch id (neither through devlink nor .ndo_get_port_parent_id), therefore the bridge assigns them a hardware domain of 0, and packets coming from them will always have skb->offload_fwd_mark = 0. So there aren't any restrictions. Problems appear due to the fact that DSA would like to perform software fallback for bonding and team interfaces that the physical switch cannot offload. +-- br0 ---+ / / | \ / / | \ / | | bond0 / | | / \ swp0 swp1 swp2 swp3 swp4 There, it is desirable that the presence of swp3 and swp4 under a non-offloaded LAG does not preclude us from doing hardware bridging beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high enough that software bridging between {swp0,swp1,swp2} and bond0 is not impractical. But this creates an impossible paradox given the current way in which port hardware domains are assigned. When the driver receives a packet from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to something. - If we set it to 0, then the bridge will forward it towards swp1, swp2 and bond0. But the switch has already forwarded it towards swp1 and swp2 (not to bond0, remember, that isn't offloaded, so as far as the switch is concerned, ports swp3 and swp4 are not looking up the FDB, and the entire bond0 is a destination that is strictly behind the CPU). But we don't want duplicated traffic towards swp1 and swp2, so it's not ok to set skb->offload_fwd_mark = 0. - If we set it to 1, then the bridge will not forward the skb towards the ports with the same switchdev mark, i.e. not to swp1, swp2 and bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should have forwarded the skb there. So the real issue is that bond0 will be assigned the same hardware domain as {swp0,swp1,swp2}, because the function that assigns hardware domains to bridge ports, nbp_switchdev_add(), recurses through bond0's lower interfaces until it finds something that implements devlink (calls dev_get_port_parent_id with bool recurse = true). This is a problem because the fact that bond0 can be offloaded by swp3 and swp4 in our example is merely an assumption. A solution is to give the bridge explicit hints as to what hardware domain it should use for each port. Currently, the bridging offload is very 'silent': a driver registers a netdevice notifier, which is put on the netns's notifier chain, and which sniffs around for NETDEV_CHANGEUPPER events where the upper is a bridge, and the lower is an interface it knows about (one registered by this driver, normally). Then, from within that notifier, it does a bunch of stuff behind the bridge's back, without the bridge necessarily knowing that there's somebody offloading that port. It looks like this: ip link set swp0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v call_netdevice_notifiers | v dsa_slave_netdevice_event | v oh, hey! it's for me! | v .port_bridge_join What we do to solve the conundrum is to be less silent, and change the switchdev drivers to present themselves to the bridge. Something like this: ip link set swp0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v bridge: Aye! I'll use this call_netdevice_notifiers ^ ppid as the | | hardware domain for v | this port, and zero dsa_slave_netdevice_event | if I got nothing. | | v | oh, hey! it's for me! | | | v | .port_bridge_join | | | +------------------------+ switchdev_bridge_port_offload(swp0, swp0) Then stacked interfaces (like bond0 on top of swp3/swp4) would be treated differently in DSA, depending on whether we can or cannot offload them. The offload case: ip link set bond0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v bridge: Aye! I'll use this call_netdevice_notifiers ^ ppid as the | | switchdev mark for v | bond0. dsa_slave_netdevice_event | Coincidentally (or not), | | bond0 and swp0, swp1, swp2 v | all have the same switchdev hmm, it's not quite for me, | mark now, since the ASIC but my driver has already | is able to forward towards called .port_lag_join | all these ports in hw. for it, because I have | a port with dp->lag_dev == bond0. | | | v | .port_bridge_join | for swp3 and swp4 | | | +------------------------+ switchdev_bridge_port_offload(bond0, swp3) switchdev_bridge_port_offload(bond0, swp4) And the non-offload case: ip link set bond0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v bridge waiting: call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload | | wasn't called, okay, I'll use a v | hwdom of zero for this one. dsa_slave_netdevice_event : Then packets received on swp0 will | : not be software-forwarded towards v : swp1, but they will towards bond0. it's not for me, but bond0 is an upper of swp3 and swp4, but their dp->lag_dev is NULL because they couldn't offload it. Basically we can draw the conclusion that the lowers of a bridge port can come and go, so depending on the configuration of lowers for a bridge port, it can dynamically toggle between offloaded and unoffloaded. Therefore, we need an equivalent switchdev_bridge_port_unoffload too. This patch changes the way any switchdev driver interacts with the bridge. From now on, everybody needs to call switchdev_bridge_port_offload and switchdev_bridge_port_unoffload, otherwise the bridge will treat the port as non-offloaded and allow software flooding to other ports from the same ASIC. Note that these functions lay the ground for a more complex handshake between switchdev drivers and the bridge in the future. For drivers that will request a replay of the switchdev objects when they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we place the call to switchdev_bridge_port_unoffload() strategically inside the NETDEV_PRECHANGEUPPER notifier's code path, and not inside NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers need the netdev adjacency lists to be valid, and that is only true in NETDEV_PRECHANGEUPPER. Cc: Vadym Kochan <vkochan@marvell.com> Cc: Taras Chornyi <tchornyi@marvell.com> Cc: Ioana Ciornei <ioana.ciornei@nxp.com> Cc: Lars Povlsen <lars.povlsen@microchip.com> Cc: Steen Hegelund <Steen.Hegelund@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-29net: bridge: allow the switchdev replay functions to be called for deletionVladimir Oltean1-6/+6
When a switchdev port leaves a LAG that is a bridge port, the switchdev objects and port attributes offloaded to that port are not removed: ip link add br0 type bridge ip link add bond0 type bond mode 802.3ad ip link set swp0 master bond0 ip link set bond0 master br0 bridge vlan add dev bond0 vid 100 ip link set swp0 nomaster VLAN 100 will remain installed on swp0 despite it going into standalone mode, because as far as the bridge is concerned, nothing ever happened to its bridge port. Let's extend the bridge vlan, fdb and mdb replay functions to take a 'bool adding' argument, and make DSA and ocelot call the replay functions with 'adding' as false from the switchdev unsync path, for the switch port that leaves the bridge. Note that this patch in itself does not salvage anything, because in the current pull mode of operation, DSA still needs to call the replay helpers with adding=false. This will be done in another patch. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-29net: bridge: constify variables in the replay helpersVladimir Oltean1-7/+7
Some of the arguments and local variables for the newly added switchdev replay helpers can be const, so let's make them so. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-29net: bridge: ignore switchdev events for LAG ports which didn't request replayVladimir Oltean1-6/+8
There is a slight inconvenience in the switchdev replay helpers added recently, and this is when: ip link add br0 type bridge ip link add bond0 type bond ip link set bond0 master br0 bridge vlan add dev bond0 vid 100 ip link set swp0 master bond0 ip link set swp1 master bond0 Since the underlying driver (currently only DSA) asks for a replay of VLANs when swp0 and swp1 join the LAG because it is bridged, what will happen is that DSA will try to react twice on the VLAN event for swp0. This is not really a huge problem right now, because most drivers accept duplicates since the bridge itself does, but it will become a problem when we add support for replaying switchdev object deletions. Let's fix this by adding a blank void *ctx in the replay helpers, which will be passed on by the bridge in the switchdev notifications. If the context is NULL, everything is the same as before. But if the context is populated with a valid pointer, the underlying switchdev driver (currently DSA) can use the pointer to 'see through' the bridge port (which in the example above is bond0) and 'know' that the event is only for a particular physical port offloading that bridge port, and not for all of them. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-05-14net: bridge: mcast: export multicast router presence adjacent to a portLinus Lüssing1-0/+8
To properly support routable multicast addresses in batman-adv in a group-aware way, a batman-adv node needs to know if it serves multicast routers. This adds a function to the bridge to export this so that batman-adv can then make full use of the Multicast Router Discovery capability of the bridge. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-24net: bridge: add helper to replay VLANs installed on portVladimir Oltean1-0/+10
Currently this simple setup with DSA: ip link add br0 type bridge vlan_filtering 1 ip link add bond0 type bond ip link set bond0 master br0 ip link set swp0 master bond0 will not work because the bridge has created the PVID in br_add_if -> nbp_vlan_init, and it has notified switchdev of the existence of VLAN 1, but that was too early, since swp0 was not yet a lower of bond0, so it had no reason to act upon that notification. We need a helper in the bridge to replay the switchdev VLAN objects that were notified since the bridge port creation, because some of them may have been missed. As opposed to the br_mdb_replay function, the vg->vlan_list write side protection is offered by the rtnl_mutex which is sleepable, so we don't need to queue up the objects in atomic context, we can replay them right away. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-24net: bridge: add helper to replay port and local fdb entriesVladimir Oltean1-0/+9
When a switchdev port starts offloading a LAG that is already in a bridge and has an FDB entry pointing to it: ip link set bond0 master br0 bridge fdb add dev bond0 00:01:02:03:04:05 master static ip link set swp0 master bond0 the switchdev driver will have no idea that this FDB entry is there, because it missed the switchdev event emitted at its creation. Ido Schimmel pointed this out during a discussion about challenges with switchdev offloading of stacked interfaces between the physical port and the bridge, and recommended to just catch that condition and deny the CHANGEUPPER event: https://lore.kernel.org/netdev/20210210105949.GB287766@shredder.lan/ But in fact, we might need to deal with the hard thing anyway, which is to replay all FDB addresses relevant to this port, because it isn't just static FDB entries, but also local addresses (ones that are not forwarded but terminated by the bridge). There, we can't just say 'oh yeah, there was an upper already so I'm not joining that'. So, similar to the logic for replaying MDB entries, add a function that must be called by individual switchdev drivers and replays local FDB entries as well as ones pointing towards a bridge port. This time, we use the atomic switchdev notifier block, since that's what FDB entries expect for some reason. Reported-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-24net: bridge: add helper to replay port and host-joined mdb entriesVladimir Oltean1-0/+9
I have a system with DSA ports, and udhcpcd is configured to bring interfaces up as soon as they are created. I create a bridge as follows: ip link add br0 type bridge As soon as I create the bridge and udhcpcd brings it up, I also have avahi which automatically starts sending IPv6 packets to advertise some local services, and because of that, the br0 bridge joins the following IPv6 groups due to the code path detailed below: 33:33:ff:6d:c1:9c vid 0 33:33:00:00:00:6a vid 0 33:33:00:00:00:fb vid 0 br_dev_xmit -> br_multicast_rcv -> br_ip6_multicast_add_group -> __br_multicast_add_group -> br_multicast_host_join -> br_mdb_notify This is all fine, but inside br_mdb_notify we have br_mdb_switchdev_host hooked up, and switchdev will attempt to offload the host joined groups to an empty list of ports. Of course nobody offloads them. Then when we add a port to br0: ip link set swp0 master br0 the bridge doesn't replay the host-joined MDB entries from br_add_if, and eventually the host joined addresses expire, and a switchdev notification for deleting it is emitted, but surprise, the original addition was already completely missed. The strategy to address this problem is to replay the MDB entries (both the port ones and the host joined ones) when the new port joins the bridge, similar to what vxlan_fdb_replay does (in that case, its FDB can be populated and only then attached to a bridge that you offload). However there are 2 possibilities: the addresses can be 'pushed' by the bridge into the port, or the port can 'pull' them from the bridge. Considering that in the general case, the new port can be really late to the party, and there may have been many other switchdev ports that already received the initial notification, we would like to avoid delivering duplicate events to them, since they might misbehave. And currently, the bridge calls the entire switchdev notifier chain, whereas for replaying it should just call the notifier block of the new guy. But the bridge doesn't know what is the new guy's notifier block, it just knows where the switchdev notifier chain is. So for simplification, we make this a driver-initiated pull for now, and the notifier block is passed as an argument. To emulate the calling context for mdb objects (deferred and put on the blocking notifier chain), we must iterate under RCU protection through the bridge's mdb entries, queue them, and only call them once we're out of the RCU read-side critical section. There was some opportunity for reuse between br_mdb_switchdev_host_port, br_mdb_notify and the newly added br_mdb_queue_one in how the switchdev mdb object is created, so a helper was created. Suggested-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-24net: bridge: add helper to retrieve the current ageing timeVladimir Oltean1-0/+6
The SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME attribute is only emitted from: sysfs/ioctl/netlink -> br_set_ageing_time -> __set_ageing_time therefore not at bridge port creation time, so: (a) switchdev drivers have to hardcode the initial value for the address ageing time, because they didn't get any notification (b) that hardcoded value can be out of sync, if the user changes the ageing time before enslaving the port to the bridge We need a helper in the bridge, such that switchdev drivers can query the current value of the bridge ageing time when they start offloading it. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-24net: bridge: add helper for retrieving the current bridge port STP stateVladimir Oltean1-0/+6
It may happen that we have the following topology with DSA or any other switchdev driver with LAG offload: ip link add br0 type bridge stp_state 1 ip link add bond0 type bond ip link set bond0 master br0 ip link set swp0 master bond0 ip link set swp1 master bond0 STP decides that it should put bond0 into the BLOCKING state, and that's that. The ports that are actively listening for the switchdev port attributes emitted for the bond0 bridge port (because they are offloading it) and have the honor of seeing that switchdev port attribute can react to it, so we can program swp0 and swp1 into the BLOCKING state. But if then we do: ip link set swp2 master bond0 then as far as the bridge is concerned, nothing has changed: it still has one bridge port. But this new bridge port will not see any STP state change notification and will remain FORWARDING, which is how the standalone code leaves it in. We need a function in the bridge driver which retrieves the current STP state, such that drivers can synchronize to it when they may have missed switchdev events. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-10-31net: bridge: mcast: add support for raw L2 multicast groupsNikolay Aleksandrov1-0/+1
Extend the bridge multicast control and data path to configure routes for L2 (non-IP) multicast groups. The uapi struct br_mdb_entry union u is extended with another variant, mac_addr, which does not change the structure size, and which is valid when the proto field is zero. To be compatible with the forwarding code that is already in place, which acts as an IGMP/MLD snooping bridge with querier capabilities, we need to declare that for L2 MDB entries (for which there exists no such thing as IGMP/MLD snooping/querying), that there is always a querier. Otherwise, these entries would be flooded to all bridge ports and not just to those that are members of the L2 multicast group. Needless to say, only permanent L2 multicast groups can be installed on a bridge port. Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20201028233831.610076-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-09-23net: bridge: mcast: rename br_ip's u member to dstNikolay Aleksandrov1-1/+1
Since now we have src in br_ip, u no longer makes sense so rename it to dst. No functional changes. v2: fix build with CONFIG_BATMAN_ADV_MCAST CC: Marek Lindner <mareklindner@neomailbox.ch> CC: Simon Wunderlich <sw@simonwunderlich.de> CC: Antonio Quartulli <a@unstable.cc> CC: Sven Eckelmann <sven@narfation.org> CC: b.a.t.m.a.n@lists.open-mesh.org Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-23net: bridge: add src field to br_ipNikolay Aleksandrov1-0/+6
Add a new src field to struct br_ip which will be used to lookup S, G entries. When SSM option is added we will enable full br_ip lookups. Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14bridge: mrp: Extend bridge interfaceHoratiu Vultur1-0/+1
This patch adds a new flag(BR_MRP_LOST_IN_CONT) to the net bridge ports. This bit will be set when the port lost the continuity of MRP_InTest frames. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-27bridge: mrp: Extend bridge interfaceHoratiu Vultur1-0/+2
To integrate MRP into the bridge, first the bridge needs to be aware of ports that are part of an MRP ring and which rings are on the bridge. Therefore extend bridge interface with the following: - add new flag(BR_MPP_AWARE) to the net bridge ports, this bit will be set when the port is added to an MRP instance. In this way it knows if the frame was received on MRP ring port - add new flag(BR_MRP_LOST_CONT) to the net bridge ports, this bit will be set when the port lost the continuity of MRP Test frames. - add a list of MRP instances Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-05bridge: add br_vlan_get_proto()wenxu1-0/+6
This new function allows you to fetch the bridge port vlan protocol. Signed-off-by: wenxu <wenxu@ucloud.cn> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2019-07-05bridge: add br_vlan_get_pvid_rcu()Pablo Neira Ayuso1-0/+6
This new function allows you to fetch bridge pvid from packet path. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner1-5/+1
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-12bridge: broute: make broute a real ebtables tableFlorian Westphal1-3/+0
This makes broute a normal ebtables table, hooking at PREROUTING. The broute hook is removed. It uses skb->cb to signal to bridge rx handler that the skb should be routed instead of being bridged. This change is backwards compatible with ebtables as no userspace visible parts are changed. This means we can also remove the !ops test in ebt_register_table, it was only there for broute table sake. Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2018-12-07bridge: Add br_fdb_clear_offload()Petr Machata1-0/+6
When a driver unoffloads all FDB entries en bloc, it's inefficient to send the switchdev notification one by one. Add a helper that unsets the offload flag on FDB entries on a given bridge port and VLAN. Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-22bridge: Allow querying bridge port flagsIdo Schimmel1-0/+6
Allow querying bridge port flags so that drivers capable of performing VxLAN learning will update the bridge driver only if learning is enabled on its bridge port corresponding to the VxLAN device. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-07net: bridge: fix br_vlan_get_{pvid,info} return valuesArnd Bergmann1-2/+2
These two functions return the regular -EINVAL failure in the normal code path, but return a nonstandard '-1' error otherwise, which gets interpreted as -EPERM. Let's change it to -EINVAL for the dummy functions as well. Fixes: 4d4fd36126d6 ("net: bridge: Publish bridge accessor functions") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-25net: bridge: add support for port isolationNikolay Aleksandrov1-0/+1
This patch adds support for a new port flag - BR_ISOLATED. If it is set then isolated ports cannot communicate between each other, but they can still communicate with non-isolated ports. The same can be achieved via ACLs but they can't scale with large number of ports and also the complexity of the rules grows. This feature can be used to achieve isolated vlan functionality (similar to pvlan) as well, though currently it will be port-wide (for all vlans on the port). The new test in should_deliver uses data that is already cache hot and the new boolean is used to avoid an additional source port test in should_deliver. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-30net: bridge: Publish bridge accessor functionsPetr Machata1-0/+28
Add a couple new functions to allow querying FDB and vlan settings of a bridge. Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09net: bridge: Export bridge multicast router stateYotam Gigi1-0/+5
Add an access function that, given a bridge netdevice, returns whether the bridge device is currently an mrouter or not. The function uses the already existing br_multicast_is_router function to check that. This function is needed in order to allow ports that join an already existing bridge to know the current mrouter state of the bridge device. Together with the bridge device mrouter ports switchdev notifications, it is possible to have full offloading of the semantics of the bridge device mcast router state. Due to the fact that the bridge multicast router status can change in packet RX path, take the multicast_router bridge spinlock to protect the read. Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Reviewed-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd floodRoopa Prabhu1-0/+1
This patch adds a new bridge port flag BR_NEIGH_SUPPRESS to suppress arp and nd flood on bridge ports. It implements rfc7432, section 10. https://tools.ietf.org/html/rfc7432#section-10 for ethernet VPN deployments. It is similar to the existing BR_PROXYARP* flags but has a few semantic differences to conform to EVPN standard. Unlike the existing flags, this new flag suppresses flood of all neigh discovery packets (arp and nd) to tunnel ports. Supports both vlan filtering and non-vlan filtering bridges. In case of EVPN, it is mainly used to avoid flooding of arp and nd packets to tunnel ports like vxlan. This patch adds netlink and sysfs support to set this bridge port flag. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-26bridge: Export multicast enabled stateIdo Schimmel1-0/+5
During enslavement to a bridge, after the CHANGEUPPER is sent, the multicast enabled state of the bridge isn't propagated down to the offloading driver unless it's changed. This patch allows such drivers to query the multicast enabled state from the bridge, so that they'll be able to correctly configure their flood tables during port enslavement. In case multicast is disabled, unregistered multicast packets can be treated as broadcast and be flooded through all the bridge ports. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-26bridge: Export VLAN filtering stateIdo Schimmel1-0/+9
It's useful for drivers supporting bridge offload to be able to query the bridge's VLAN filtering state. Currently, upon enslavement to a bridge master, the offloading driver will only learn about the bridge's VLAN filtering state after the bridge device was already linked with its slave. Being able to query the bridge's VLAN filtering state allows such drivers to forbid enslavement in case resource couldn't be allocated for a VLAN-aware bridge and also choose the correct initialization routine for the enslaved port, which is dependent on the bridge type. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-27bridge: add per-port broadcast flood flagMike Manning1-0/+1
Support for l2 multicast flood control was added in commit b6cb5ac8331b ("net: bridge: add per-port multicast flood flag"). It allows broadcast as it was introduced specifically for unknown multicast flood control. But as broadcast is a special case of multicast, this may also need to be disabled. For this purpose, introduce a flag to disable the flooding of received l2 broadcasts. This approach is backwards compatible and provides flexibility in filtering for the desired packet types. Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Mike Manning <mmanning@brocade.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-03bridge: uapi: add per vlan tunnel infoRoopa Prabhu1-0/+1
New nested netlink attribute to associate tunnel info per vlan. This is used by bridge driver to send tunnel metadata to bridge ports in vlan tunnel mode. This patch also adds new per port flag IFLA_BRPORT_VLAN_TUNNEL to enable vlan tunnel mode. off by default. One example use for this is a vxlan bridging gateway or vtep which maps vlans to vn-segments (or vnis). User can configure per-vlan tunnel information which the bridge driver can use to bridge vlan into the corresponding vn-segment. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-24bridge: multicast to unicastFelix Fietkau1-0/+1
Implements an optional, per bridge port flag and feature to deliver multicast packets to any host on the according port via unicast individually. This is done by copying the packet per host and changing the multicast destination MAC to a unicast one accordingly. multicast-to-unicast works on top of the multicast snooping feature of the bridge. Which means unicast copies are only delivered to hosts which are interested in it and signalized this via IGMP/MLD reports previously. This feature is intended for interface types which have a more reliable and/or efficient way to deliver unicast packets than broadcast ones (e.g. wifi). However, it should only be enabled on interfaces where no IGMPv2/MLDv1 report suppression takes place. This feature is disabled by default. The initial patch and idea is from Felix Fietkau. Signed-off-by: Felix Fietkau <nbd@nbd.name> [linus.luessing@c0d3.blue: various bug + style fixes, commit message] Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-02net: bridge: add per-port multicast flood flagNikolay Aleksandrov1-0/+1
Add a per-port flag to control the unknown multicast flood, similar to the unknown unicast flood flag and break a few long lines in the netlink flag exports. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-11bridge: allow zero ageing timeStephen Hemminger1-4/+0
This fixes a regression in the bridge ageing time caused by: commit c62987bbd8a1 ("bridge: push bridge setting ageing_time down to switchdev") There are users of Linux bridge which use the feature that if ageing time is set to 0 it causes entries to never expire. See: https://www.linuxfoundation.org/collaborate/workgroups/networking/bridge For a pure software bridge, it is unnecessary for the code to have arbitrary restrictions on what values are allowable. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-24bridge: define some min/max/default ageing time constantsScott Feldman1-0/+6
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-05bridge: Extend Proxy ARP design to allow optional rules for Wi-FiJouni Malinen1-0/+1
This extends the design in commit 958501163ddd ("bridge: Add support for IEEE 802.11 Proxy ARP") with optional set of rules that are needed to meet the IEEE 802.11 and Hotspot 2.0 requirements for ProxyARP. The previously added BR_PROXYARP behavior is left as-is and a new BR_PROXYARP_WIFI alternative is added so that this behavior can be configured from user space when required. In addition, this enables proxyarp functionality for unicast ARP requests for both BR_PROXYARP and BR_PROXYARP_WIFI since it is possible to use unicast as well as broadcast for these frames. The key differences in functionality: BR_PROXYARP: - uses the flag on the bridge port on which the request frame was received to determine whether to reply - block bridge port flooding completely on ports that enable proxy ARP BR_PROXYARP_WIFI: - uses the flag on the bridge port to which the target device of the request belongs - block bridge port flooding selectively based on whether the proxyarp functionality replied Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-18net: replace br_fdb_external_learn_* calls with switchdev notifier eventsJiri Pirko1-18/+0
This patch benefits from newly introduced switchdev notifier and uses it to propagate fdb learn events from rocker driver to bridge. That avoids direct function calls and possible use by other listeners (ovs). Suggested-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-03bridge: add new brport flag LEARNING_SYNCScott Feldman1-0/+1
This policy flag controls syncing of learned FDB entries to bridge's FDB. If on, FDB entries learned on bridge port device will be synced. If off, device may still learn new FDB entries but they will not be synced with bridge's FDB. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-03bridge: move private brport flags to if_bridge.h so port drivers can use flagsScott Feldman1-0/+12
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-03bridge: add API to notify bridge driver of learned FBD on offloaded deviceScott Feldman1-0/+18
When the swdev device learns a new mac/vlan on a port, it sends some async notification to the driver and the driver installs an FDB in the device. To give a holistic system view, the learned mac/vlan should be reflected in the bridge's FBD table, so the user, using normal iproute2 cmds, can view what is currently learned by the device. This API on the bridge driver gives a way for the swdev driver to install an FBD entry in the bridge FBD table. (And remove one). This is equivalent to the device running these cmds: bridge fdb [add|del] <mac> dev <dev> vid <vlan id> master This patch needs some extra eyeballs for review, in paricular around the locking and contexts. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-09bridge: export knowledge about the presence of IGMP/MLD queriersLinus Lüssing1-0/+6
With this patch other modules are able to ask the bridge whether an IGMP or MLD querier exists on the according, bridged link layer. Multicast snooping can only be performed if a valid, selected querier exists on a link. Just like the bridge only enables its multicast snooping if a querier exists, e.g. batman-adv too can only activate its multicast snooping in bridged scenarios if a querier is present. For instance this export avoids having to reimplement IGMP/MLD querier message snooping and parsing in e.g. batman-adv, when multicast optimizations for bridged scenarios are added in the future. Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-09bridge: adding stubs for multicast exportsLinus Lüssing1-0/+14
To make users (e.g. batman-adv soon) load- and runnable even if the bridge was compiled without snooping capabilities - or even if the kernel was compiled without any bridge code at all. Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-11bridge: memorize and export selected IGMP/MLD querier portLinus Lüssing1-0/+1
Adding bridge support to the batman-adv multicast optimization requires batman-adv knowing about the existence of bridged-in IGMP/MLD queriers to be able to reliably serve any multicast listener behind this same bridge. Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-11bridge: add export of multicast database adjacent to net_devLinus Lüssing1-0/+18
With this new, exported function br_multicast_list_adjacent(net_dev) a list of IPv4/6 addresses is returned. This list contains all multicast addresses sensed by the bridge multicast snooping feature on all bridge ports of the bridge interface of net_dev, excluding addresses from the specified net_device itself. Adding bridge support to the batman-adv multicast optimization requires batman-adv knowing about the existence of bridged-in multicast listeners to be able to reliably serve them with multicast packets. Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-13UAPI: (Scripted) Disintegrate include/linuxDavid Howells1-88/+1
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michael Kerrisk <mtk.manpages@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Dave Jones <davej@redhat.com>
2011-01-12netfilter: ebtables: make broute table work againFlorian Westphal1-1/+1
broute table init hook sets up the "br_should_route_hook" pointer, which then gets called from br_input. commit a386f99025f13b32502fe5dedf223c20d7283826 (bridge: add proper RCU annotation to should_route_hook) introduced a typedef, and then changed this to: br_should_route_hook_t *rhook; [..] rhook = rcu_dereference(br_should_route_hook); if (*rhook(skb)) problem is that "br_should_route_hook" contains the address of the function, so calling *rhook() results in kernel panic. Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>