| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add the GETMRL/SETMRL and GETMWL/SETMWL CCC commands functions.
The functions are needed to configure maximum read/write length
for the specific I3C device.
Signed-off-by: Oleksandr Shulzhenko <oleksandr.shulzhenko.viktorovych@intel.com>
|
|
- Handler for PECI messages have been added;
- i3c_mctp_client and platform_device for PECI have been added.
Signed-off-by: Oleksandr Shulzhenko <oleksandr.shulzhenko.viktorovych@intel.com>
|
|
Extend the driver with the functionality necessary to send
and receive MCTP over I3C packets by another component in kernel:
- i3c_mctp_client concept needed to implement packet queue so that
the driver can manage and classify packets for several clients
respectively;
- the function that provides MCTP target EID;
- the functions to alloc and free mctp_i3c_packet;
- the functions to send and receive MCTP packets over I3C.
Signed-off-by: Oleksandr Shulzhenko <oleksandr.shulzhenko.viktorovych@intel.com>
|
|
Since PECI Target addressing has been changed to use Domain ID
information, each peci_client instance should correspond with both CPU
ID and Domain ID.
Let's extend peci_client structure, sysfs API and intel-peci-client to
use Domain ID. Make MFD device ID as a combination of peci adapter
number, CPU ID and Domain ID.
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
|
|
PEC (Packet Error Check) support enabled in I3C controller driver. API
for I3C device driver to control (enable or disable) PEC support in
lower layer driver added.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
|
|
https://github.com/openbmc/linux into openbmc/dev-5.15-intel-bump_v5.15.36
Signed-off-by: Sujoy Ray <sujoy.ray@intel.com>
|
|
Add support to deselect the mux when there is a timeout.
The mux idle_state settings will be configured on startup. In case of
MCTP it is MUX_IDLE_DISCONNECT. But when there is a timeout, mux ends
up in connected position and the devices behind the mux will appear under
different muxes connected to the same bus. This change fix the same.
Signed-off-by: Arun P. Mohanan <arun.p.m@linux.intel.com>
|
|
This is the 5.15.36 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
commit 6ae7989c9af0d98ab64196f4f4c6f6499454bd23 upstream.
nf_ct_put() results in a usesless indirection:
nf_ct_put -> nf_conntrack_put -> nf_conntrack_destroy -> rcu readlock +
indirect call of ct_hooks->destroy().
There are two _put helpers:
nf_ct_put and nf_conntrack_put. The latter is what should be used in
code that MUST NOT cause a linker dependency on the conntrack module
(e.g. calls from core network stack).
Everyone else should call nf_ct_put() instead.
A followup patch will convert a few nf_conntrack_put() calls to
nf_ct_put(), in particular from modules that already have a conntrack
dependency such as act_ct or even nf_conntrack itself.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 719774377622bc4025d2a74f551b5dc2158c6c30 upstream.
Convert nf_conn reference counting from atomic_t to refcount_t based api.
refcount_t api provides more runtime sanity checks and will warn on
certain constructs, e.g. refcount_inc() on a zero reference count, which
usually indicates use-after-free.
For this reason template allocation is changed to init the refcount to
1, the subsequenct add operations are removed.
Likewise, init_conntrack() is changed to set the initial refcount to 1
instead refcount_inc().
This is safe because the new entry is not (yet) visible to other cpus.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4a38402c36e42df28eb1a5394be87e6571fb48a upstream.
The pthread struct is allocated on PRIVATE|ANONYMOUS memory [1] which
can be targeted by the oom reaper. This mapping is used to store the
futex robust list head; the kernel does not keep a copy of the robust
list and instead references a userspace address to maintain the
robustness during a process death.
A race can occur between exit_mm and the oom reaper that allows the oom
reaper to free the memory of the futex robust list before the exit path
has handled the futex death:
CPU1 CPU2
--------------------------------------------------------------------
page_fault
do_exit "signal"
wake_oom_reaper
oom_reaper
oom_reap_task_mm (invalidates mm)
exit_mm
exit_mm_release
futex_exit_release
futex_cleanup
exit_robust_list
get_user (EFAULT- can't access memory)
If the get_user EFAULT's, the kernel will be unable to recover the
waiters on the robust_list, leaving userspace mutexes hung indefinitely.
Delay the OOM reaper, allowing more time for the exit path to perform
the futex cleanup.
Reproducer: https://gitlab.com/jsavitz/oom_futex_reproducer
Based on a patch by Michal Hocko.
Link: https://elixir.bootlin.com/glibc/glibc-2.35/source/nptl/allocatestack.c#L370 [1]
Link: https://lkml.kernel.org/r/20220414144042.677008-1-npache@redhat.com
Fixes: 212925802454 ("mm: oom: let oom_reap_task and exit_mmap run concurrently")
Signed-off-by: Joel Savitz <jsavitz@redhat.com>
Signed-off-by: Nico Pache <npache@redhat.com>
Co-developed-by: Joel Savitz <jsavitz@redhat.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Waiman Long <longman@redhat.com>
Cc: Herton R. Krzesinski <herton@redhat.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Daniel Bristot de Oliveira <bristot@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joel Savitz <jsavitz@redhat.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5f24d5a579d1eace79d505b148808a850b417d4c upstream.
This is a fix for commit f6795053dac8 ("mm: mmap: Allow for "high"
userspace addresses") for hugetlb.
This patch adds support for "high" userspace addresses that are
optionally supported on the system and have to be requested via a hint
mechanism ("high" addr parameter to mmap).
Architectures such as powerpc and x86 achieve this by making changes to
their architectural versions of hugetlb_get_unmapped_area() function.
However, arm64 uses the generic version of that function.
So take into account arch_get_mmap_base() and arch_get_mmap_end() in
hugetlb_get_unmapped_area(). To allow that, move those two macros out
of mm/mmap.c into include/linux/sched/mm.h
If these macros are not defined in architectural code then they default
to (TASK_SIZE) and (base) so should not introduce any behavioural
changes to architectures that do not define them.
For the time being, only ARM64 is affected by this change.
Catalin (ARM64) said
"We should have fixed hugetlb_get_unmapped_area() as well when we added
support for 52-bit VA. The reason for commit f6795053dac8 was to
prevent normal mmap() from returning addresses above 48-bit by default
as some user-space had hard assumptions about this.
It's a slight ABI change if you do this for hugetlb_get_unmapped_area()
but I doubt anyone would notice. It's more likely that the current
behaviour would cause issues, so I'd rather have them consistent.
Basically when arm64 gained support for 52-bit addresses we did not
want user-space calling mmap() to suddenly get such high addresses,
otherwise we could have inadvertently broken some programs (similar
behaviour to x86 here). Hence we added commit f6795053dac8. But we
missed hugetlbfs which could still get such high mmap() addresses. So
in theory that's a potential regression that should have bee addressed
at the same time as commit f6795053dac8 (and before arm64 enabled
52-bit addresses)"
Link: https://lkml.kernel.org/r/ab847b6edb197bffdfe189e70fb4ac76bfe79e0d.1650033747.git.christophe.leroy@csgroup.eu
Fixes: f6795053dac8 ("mm: mmap: Allow for "high" userspace addresses")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> [5.0.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9b3016154c913b2e7ec5ae5c9a42eb9e732d86aa upstream.
Daniel Dao has reported [1] a regression on workloads that may trigger a
lot of refaults (anon and file). The underlying issue is that flushing
rstat is expensive. Although rstat flush are batched with (nr_cpus *
MEMCG_BATCH) stat updates, it seems like there are workloads which
genuinely do stat updates larger than batch value within short amount of
time. Since the rstat flush can happen in the performance critical
codepaths like page faults, such workload can suffer greatly.
This patch fixes this regression by making the rstat flushing
conditional in the performance critical codepaths. More specifically,
the kernel relies on the async periodic rstat flusher to flush the stats
and only if the periodic flusher is delayed by more than twice the
amount of its normal time window then the kernel allows rstat flushing
from the performance critical codepaths.
Now the question: what are the side-effects of this change? The worst
that can happen is the refault codepath will see 4sec old lruvec stats
and may cause false (or missed) activations of the refaulted page which
may under-or-overestimate the workingset size. Though that is not very
concerning as the kernel can already miss or do false activations.
There are two more codepaths whose flushing behavior is not changed by
this patch and we may need to come to them in future. One is the
writeback stats used by dirty throttling and second is the deactivation
heuristic in the reclaim. For now keeping an eye on them and if there
is report of regression due to these codepaths, we will reevaluate then.
Link: https://lore.kernel.org/all/CA+wXwBSyO87ZX5PVwdHm-=dBjZYECGmfnydUicUyrQqndgX2MQ@mail.gmail.com [1]
Link: https://lkml.kernel.org/r/20220304184040.1304781-1-shakeelb@google.com
Fixes: 1f828223b799 ("memcg: flush lruvec stats in the refault")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reported-by: Daniel Dao <dqminh@cloudflare.com>
Tested-by: Ivan Babrou <ivan@cloudflare.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Koutný <mkoutny@suse.com>
Cc: Frank Hofmann <fhofmann@cloudflare.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2dfe63e61cc31ee59ce951672b0850b5229cd5b0 upstream.
Calling kmem_obj_info() via kmem_dump_obj() on KFENCE objects has been
producing garbage data due to the object not actually being maintained
by SLAB or SLUB.
Fix this by implementing __kfence_obj_info() that copies relevant
information to struct kmem_obj_info when the object was allocated by
KFENCE; this is called by a common kmem_obj_info(), which also calls the
slab/slub/slob specific variant now called __kmem_obj_info().
For completeness, kmem_dump_obj() now displays if the object was
allocated by KFENCE.
Link: https://lore.kernel.org/all/20220323090520.GG16885@xsang-OptiPlex-9020/
Link: https://lkml.kernel.org/r/20220406131558.3558585-1-elver@google.com
Fixes: b89fb5ef0ce6 ("mm, kfence: insert KFENCE hooks for SLUB")
Fixes: d3fb45f370d9 ("mm, kfence: insert KFENCE hooks for SLAB")
Signed-off-by: Marco Elver <elver@google.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz> [slab]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2618a0dae09ef37728dab89ff60418cbe25ae6bd upstream.
With GCC 12, -Wstringop-overread was warning about an implicit cast from
char[6] to char[8]. However, the extra 2 bytes are always thrown away,
alignment doesn't matter, and the risk of hitting the edge of unallocated
memory has been accepted, so this prototype can just be converted to a
regular char *. Silences:
net/core/dev.c: In function ‘bpf_prog_run_generic_xdp’: net/core/dev.c:4618:21: warning: ‘ether_addr_equal_64bits’ reading 8 bytes from a region of size 6 [-Wstringop-overread]
4618 | orig_host = ether_addr_equal_64bits(eth->h_dest, > skb->dev->dev_addr);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/core/dev.c:4618:21: note: referencing argument 1 of type ‘const u8[8]’ {aka ‘const unsigned char[8]’}
net/core/dev.c:4618:21: note: referencing argument 2 of type ‘const u8[8]’ {aka ‘const unsigned char[8]’}
In file included from net/core/dev.c:91: include/linux/etherdevice.h:375:20: note: in a call to function ‘ether_addr_equal_64bits’
375 | static inline bool ether_addr_equal_64bits(const u8 addr1[6+2],
| ^~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/netdev/20220212090811.uuzk6d76agw2vv73@pengutronix.de
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Khem Raj <raj.khem@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1e03a36bdff4709c1bbf0f57f60ae3f776d51adf ]
Get rid of the indirections and just provide a sync_bdevs
helper for the generic sync code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211019062530.2174626-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70164eb6ccb76ab679b016b4b60123bf4ec6c162 ]
Instead offer a new sync_blockdev_nowait helper for the !wait case.
This new helper is exported as it will grow modular callers in a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211019062530.2174626-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 5.15.35 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
commit 773f91b2cf3f52df0d7508fdbf60f37567cdaee4 upstream.
Trond Myklebust reports an NFSD crash in svc_rdma_sendto(). Further
investigation shows that the crash occurred while NFSD was handling
a deferred request.
This patch addresses two inter-related issues that prevent request
deferral from working correctly for RPC/RDMA requests:
1. Prevent the crash by ensuring that the original
svc_rqst::rq_xprt_ctxt value is available when the request is
revisited. Otherwise svc_rdma_sendto() does not have a Receive
context available with which to construct its reply.
2. Possibly since before commit 71641d99ce03 ("svcrdma: Properly
compute .len and .buflen for received RPC Calls"),
svc_rdma_recvfrom() did not include the transport header in the
returned xdr_buf. There should have been no need for svc_defer()
and friends to save and restore that header, as of that commit.
This issue is addressed in a backport-friendly way by simply
having svc_rdma_recvfrom() set rq_xprt_hlen to zero
unconditionally, just as svc_tcp_recvfrom() does. This enables
svc_deferred_recv() to correctly reconstruct an RPC message
received via RPC/RDMA.
Reported-by: Trond Myklebust <trondmy@hammerspace.com>
Link: https://lore.kernel.org/linux-nfs/82662b7190f26fb304eb0ab1bb04279072439d4e.camel@hammerspace.com/
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1ef3342a934e235aca72b4bcc0d6854d80a65077 ]
get_pf_vdev() tries to check if a PF is a VFIO PF by looking at the driver:
if (pci_dev_driver(physfn) != pci_dev_driver(vdev->pdev)) {
However now that we have multiple VF and PF drivers this is no longer
reliable.
This means that security tests realted to vf_token can be skipped by
mixing and matching different VFIO PCI drivers.
Instead of trying to use the driver core to find the PF devices maintain a
linked list of all PF vfio_pci_core_device's that we have called
pci_enable_sriov() on.
When registering a VF just search the list to see if the PF is present and
record the match permanently in the struct. PCI core locking prevents a PF
from passing pci_disable_sriov() while VF drivers are attached so the VFIO
owned PF becomes a static property of the VF.
In common cases where vfio does not own the PF the global list remains
empty and the VF's pointer is statically NULL.
This also fixes a lockdep splat from recursive locking of the
vfio_group::device_lock between vfio_device_get_from_name() and
vfio_device_get_from_dev(). If the VF and PF share the same group this
would deadlock.
Fixes: ff53edf6d6ab ("vfio/pci: Split the pci_driver code out of vfio_pci_core.c")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/0-v3-876570980634+f2e8-vfio_vf_token_jgg@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8c75d585b931ac874fbe4ee5a8f1811d20c2817f upstream.
Not all upcoming usecases will have an interface to allow the aoss
driver to hook onto. Expose the send api and create a get function to
enable drivers to send their own messages to aoss.
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Deepak Kumar Singh <deesin@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1630420228-31075-2-git-send-email-deesin@codeaurora.org
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
New API allows to read DomainId information by internal
kernel clients (for example peci-mctp).
Signed-off-by: Krzysztof Richert <krzysztof.richert@intel.com>
|
|
This is the 5.15.34 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
commit f39f21b3ddc7fc0f87eb6dc75ddc81b5bbfb7672 upstream.
filter_irq_stacks() has little to do with the stackdepot implementation,
except that it is usually used by users (such as KASAN) of stackdepot to
reduce the stack trace.
However, filter_irq_stacks() itself is not useful without a stack trace
as obtained by stack_trace_save() and friends.
Therefore, move filter_irq_stacks() to kernel/stacktrace.c, so that new
users of filter_irq_stacks() do not have to start depending on
STACKDEPOT only for filter_irq_stacks().
Link: https://lkml.kernel.org/r/20210923104803.2620285-1-elver@google.com
Signed-off-by: Marco Elver <elver@google.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Jann Horn <jannh@google.com>
Cc: Aleksandr Nogikh <nogikh@google.com>
Cc: Taras Madan <tarasmadan@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8fd4ddda2f49a66bf5dd3d0c01966c4b1971308b upstream.
System.map shows that vmlinux contains several instances of
__static_call_return0():
c0004fc0 t __static_call_return0
c0011518 t __static_call_return0
c00d8160 t __static_call_return0
arch_static_call_transform() uses the middle one to check whether we are
setting a call to __static_call_return0 or not:
c0011520 <arch_static_call_transform>:
c0011520: 3d 20 c0 01 lis r9,-16383 <== r9 = 0xc001 << 16
c0011524: 39 29 15 18 addi r9,r9,5400 <== r9 += 0x1518
c0011528: 7c 05 48 00 cmpw r5,r9 <== r9 has value 0xc0011518 here
So if static_call_update() is called with one of the other instances of
__static_call_return0(), arch_static_call_transform() won't recognise it.
In order to work properly, global single instance of __static_call_return0() is required.
Fixes: 3f2a8fc4b15d ("static_call/x86: Add __static_call_return0()")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/30821468a0e7d28251954b578e5051dc09300d04.1647258493.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a431dbbc540532b7465eae4fc8b56a85a9fc7d17 upstream.
The gcc 12 compiler reports a "'mem_section' will never be NULL" warning
on the following code:
static inline struct mem_section *__nr_to_section(unsigned long nr)
{
#ifdef CONFIG_SPARSEMEM_EXTREME
if (!mem_section)
return NULL;
#endif
if (!mem_section[SECTION_NR_TO_ROOT(nr)])
return NULL;
:
It happens with CONFIG_SPARSEMEM_EXTREME off. The mem_section definition
is
#ifdef CONFIG_SPARSEMEM_EXTREME
extern struct mem_section **mem_section;
#else
extern struct mem_section mem_section[NR_SECTION_ROOTS][SECTIONS_PER_ROOT];
#endif
In the !CONFIG_SPARSEMEM_EXTREME case, mem_section is a static
2-dimensional array and so the check "!mem_section[SECTION_NR_TO_ROOT(nr)]"
doesn't make sense.
Fix this warning by moving the "!mem_section[SECTION_NR_TO_ROOT(nr)]"
check up inside the CONFIG_SPARSEMEM_EXTREME block and adding an
explicit NR_SECTION_ROOTS check to make sure that there is no
out-of-bound array access.
Link: https://lkml.kernel.org/r/20220331180246.2746210-1-longman@redhat.com
Fixes: 3e347261a80b ("sparsemem extreme implementation")
Signed-off-by: Waiman Long <longman@redhat.com>
Reported-by: Justin Forbes <jforbes@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Rafael Aquini <aquini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89f42494f92f448747bd8a7ab1ae8b5d5520577d upstream.
Avoid socket state races due to repeated calls to ->connect() using the
same socket. If connect() returns 0 due to the connection having
completed, but we are in fact in a closing state, then we may leave the
XPRT_CONNECTING flag set on the transport.
Reported-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Fixes: 3be232f11a3c ("SUNRPC: Prevent immediate close+reconnect")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7372971c1be5b7d4fdd8ad237798bdc1d1d54162 upstream.
The mc146818_get_time() function returns zero on success or negative
a error code on failure. It needs to be type int.
Fixes: d35786b3a28d ("rtc: mc146818-lib: change return values of mc146818_get_time()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220111071922.GE11243@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5467801f1fcbdc46bc7298a84dbf3ca1ff2a7320 upstream.
GPIO chip irq members are exposed before they could be completely
initialized and this leads to race conditions.
One such issue was observed for the gc->irq.domain variable which
was accessed through the I2C interface in gpiochip_to_irq() before
it could be initialized by gpiochip_add_irqchip(). This resulted in
Kernel NULL pointer dereference.
Following are the logs for reference :-
kernel: Call Trace:
kernel: gpiod_to_irq+0x53/0x70
kernel: acpi_dev_gpio_irq_get_by+0x113/0x1f0
kernel: i2c_acpi_get_irq+0xc0/0xd0
kernel: i2c_device_probe+0x28a/0x2a0
kernel: really_probe+0xf2/0x460
kernel: RIP: 0010:gpiochip_to_irq+0x47/0xc0
To avoid such scenarios, restrict usage of GPIO chip irq members before
they are completely initialized.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ea6fa4961aab8f90a8aa03575a98b4bda368d4b6 ]
To prevent an infinite loop in mc146818_get_time(),
commit 211e5db19d15 ("rtc: mc146818: Detect and handle broken RTCs")
added a check for RTC availability. Together with a later fix, it
checked if bit 6 in register 0x0d is cleared.
This, however, caused a false negative on a motherboard with an AMD
SB710 southbridge; according to the specification [1], bit 6 of register
0x0d of this chipset is a scratchbit. This caused a regression in Linux
5.11 - the RTC was determined broken by the kernel and not used by
rtc-cmos.c [3]. This problem was also reported in Fedora [4].
As a better alternative, check whether the UIP ("Update-in-progress")
bit is set for longer then 10ms. If that is the case, then apparently
the RTC is either absent (and all register reads return 0xff) or broken.
Also limit the number of loop iterations in mc146818_get_time() to 10 to
prevent an infinite loop there.
The functions mc146818_get_time() and mc146818_does_rtc_work() will be
refactored later in this patch series, in order to fix a separate
problem with reading / setting the RTC alarm time. This is done so to
avoid a confusion about what is being fixed when.
In a previous approach to this problem, I implemented a check whether
the RTC_HOURS register contains a value <= 24. This, however, sometimes
did not work correctly on my Intel Kaby Lake laptop. According to
Intel's documentation [2], "the time and date RAM locations (0-9) are
disconnected from the external bus" during the update cycle so reading
this register without checking the UIP bit is incorrect.
[1] AMD SB700/710/750 Register Reference Guide, page 308,
https://developer.amd.com/wordpress/media/2012/10/43009_sb7xx_rrg_pub_1.00.pdf
[2] 7th Generation Intel ® Processor Family I/O for U/Y Platforms [...] Datasheet
Volume 1 of 2, page 209
Intel's Document Number: 334658-006,
https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/7th-and-8th-gen-core-family-mobile-u-y-processor-lines-i-o-datasheet-vol-1.pdf
[3] Functions in arch/x86/kernel/rtc.c apparently were using it.
[4] https://bugzilla.redhat.com/show_bug.cgi?id=1936688
Fixes: 211e5db19d15 ("rtc: mc146818: Detect and handle broken RTCs")
Fixes: ebb22a059436 ("rtc: mc146818: Dont test for bit 0-5 in Register D")
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-5-mat.jonczyk@o2.pl
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 515dcdcd48736576c6f5c197814da6f81c60a21e ]
The concern is that since nfsiod is sometimes required to kick off a
commit, it can get locked up waiting forever in mempool_alloc() instead
of failing gracefully and leaving the commit until later.
Try to allocate from the slab first, with GFP_KERNEL | __GFP_NORETRY,
then fall back to a non-blocking attempt to allocate from the memory
pool.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 64158668ac8b31626a8ce48db4cad08496eb8340 ]
1/ Taking the i_rwsem for swap IO triggers lockdep warnings regarding
possible deadlocks with "fs_reclaim". These deadlocks could, I believe,
eventuate if a buffered read on the swapfile was attempted.
We don't need coherence with the page cache for a swap file, and
buffered writes are forbidden anyway. There is no other need for
i_rwsem during direct IO. So never take it for swap_rw()
2/ generic_write_checks() explicitly forbids writes to swap, and
performs checks that are not needed for swap. So bypass it
for swap_rw().
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e031ec0e5a2dda53e12e0d2a7e9b15b47a3c502 ]
Resolve build errors reported against UML build for undefined
ioport_map() and ioport_unmap() functions. Without this config
option a device cannot have vfio_pci_core_device.has_vga set,
so the existing function would always return -EINVAL anyway.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20220123125737.2658758-1-geert@linux-m68k.org
Link: https://lore.kernel.org/r/164306582968.3758255.15192949639574660648.stgit@omen
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 145c7a793838add5e004e7d49a67654dc7eba147 ]
This fixes minor data-races in ip6_mc_input() and
batadv_mcast_mla_rtr_flags_softif_get_ipv6()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Adding DCR for I3C HUB. Value taken from
https://www.mipi.org/MIPI_I3C_device_characteristics_register
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
|
|
Extend the existing core implementation with I3C target support.
Add missing I3C target driver API.
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
|
|
commit 390031c942116d4733310f0684beb8db19885fe6 upstream.
Matthew Wilcox reported that there is a missing mmap_lock in
file_files_note that could possibly lead to a user after free.
Solve this by using the existing vma snapshot for consistency
and to avoid the need to take the mmap_lock anywhere in the
coredump code except for dump_vma_snapshot.
Update the dump_vma_snapshot to capture vm_pgoff and vm_file
that are neeeded by fill_files_note.
Add free_vma_snapshot to free the captured values of vm_file.
Reported-by: Matthew Wilcox <willy@infradead.org>
Link: https://lkml.kernel.org/r/20220131153740.2396974-1-willy@infradead.org
Cc: stable@vger.kernel.org
Fixes: a07279c9a8cd ("binfmt_elf, binfmt_elf_fdpic: use a VMA list snapshot")
Fixes: 2aa362c49c31 ("coredump: extend core dump note section to contain file names of mapped files")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 95c5436a4883841588dae86fb0b9325f47ba5ad3 upstream.
Move the call of dump_vma_snapshot and kvfree(vma_meta) out of the
individual coredump routines into do_coredump itself. This makes
the code less error prone and easier to maintain.
Make the vma snapshot available to the coredump routines
in struct coredump_params. This makes it easier to
change and update what is captures in the vma snapshot
and will be needed for fixing fill_file_notes.
Reviewed-by: Jann Horn <jannh@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e81e99bacc9f9347bda7808a949c1ce9fcc2bbf4 upstream.
Add an argument to swiotlb_tbl_map_single that specifies the desired
alignment of the allocated buffer. This is used by dma-iommu to ensure
the buffer is aligned to the iova granule size when using swiotlb with
untrusted sub-granule mappings. This addresses an issue where adjacent
slots could be exposed to the untrusted device if IO_TLB_SIZE < iova
granule < PAGE_SIZE.
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210929023300.335969-7-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2b88cba55883eaafbc9b7cbff0b2c7cdba71ed01 upstream.
syzbot found another way to trigger the infamous WARN_ON_ONCE(delta < len)
in skb_try_coalesce() [1]
I was able to root cause the issue to kfence.
When kfence is in action, the following assertion is no longer true:
int size = xxxx;
void *ptr1 = kmalloc(size, gfp);
void *ptr2 = kmalloc(size, gfp);
if (ptr1 && ptr2)
ASSERT(ksize(ptr1) == ksize(ptr2));
We attempted to fix these issues in the blamed commits, but forgot
that TCP was possibly shifting data after skb_unclone_keeptruesize()
has been used, notably from tcp_retrans_try_collapse().
So we not only need to keep same skb->truesize value,
we also need to make sure TCP wont fill new tailroom
that pskb_expand_head() was able to get from a
addr = kmalloc(...) followed by ksize(addr)
Split skb_unclone_keeptruesize() into two parts:
1) Inline skb_unclone_keeptruesize() for the common case,
when skb is not cloned.
2) Out of line __skb_unclone_keeptruesize() for the 'slow path'.
WARNING: CPU: 1 PID: 6490 at net/core/skbuff.c:5295 skb_try_coalesce+0x1235/0x1560 net/core/skbuff.c:5295
Modules linked in:
CPU: 1 PID: 6490 Comm: syz-executor161 Not tainted 5.17.0-rc4-syzkaller-00229-g4f12b742eb2b #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:skb_try_coalesce+0x1235/0x1560 net/core/skbuff.c:5295
Code: bf 01 00 00 00 0f b7 c0 89 c6 89 44 24 20 e8 62 24 4e fa 8b 44 24 20 83 e8 01 0f 85 e5 f0 ff ff e9 87 f4 ff ff e8 cb 20 4e fa <0f> 0b e9 06 f9 ff ff e8 af b2 95 fa e9 69 f0 ff ff e8 95 b2 95 fa
RSP: 0018:ffffc900063af268 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 00000000ffffffd5 RCX: 0000000000000000
RDX: ffff88806fc05700 RSI: ffffffff872abd55 RDI: 0000000000000003
RBP: ffff88806e675500 R08: 00000000ffffffd5 R09: 0000000000000000
R10: ffffffff872ab659 R11: 0000000000000000 R12: ffff88806dd554e8
R13: ffff88806dd9bac0 R14: ffff88806dd9a2c0 R15: 0000000000000155
FS: 00007f18014f9700(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020002000 CR3: 000000006be7a000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
tcp_try_coalesce net/ipv4/tcp_input.c:4651 [inline]
tcp_try_coalesce+0x393/0x920 net/ipv4/tcp_input.c:4630
tcp_queue_rcv+0x8a/0x6e0 net/ipv4/tcp_input.c:4914
tcp_data_queue+0x11fd/0x4bb0 net/ipv4/tcp_input.c:5025
tcp_rcv_established+0x81e/0x1ff0 net/ipv4/tcp_input.c:5947
tcp_v4_do_rcv+0x65e/0x980 net/ipv4/tcp_ipv4.c:1719
sk_backlog_rcv include/net/sock.h:1037 [inline]
__release_sock+0x134/0x3b0 net/core/sock.c:2779
release_sock+0x54/0x1b0 net/core/sock.c:3311
sk_wait_data+0x177/0x450 net/core/sock.c:2821
tcp_recvmsg_locked+0xe28/0x1fd0 net/ipv4/tcp.c:2457
tcp_recvmsg+0x137/0x610 net/ipv4/tcp.c:2572
inet_recvmsg+0x11b/0x5e0 net/ipv4/af_inet.c:850
sock_recvmsg_nosec net/socket.c:948 [inline]
sock_recvmsg net/socket.c:966 [inline]
sock_recvmsg net/socket.c:962 [inline]
____sys_recvmsg+0x2c4/0x600 net/socket.c:2632
___sys_recvmsg+0x127/0x200 net/socket.c:2674
__sys_recvmsg+0xe2/0x1a0 net/socket.c:2704
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: c4777efa751d ("net: add and use skb_unclone_keeptruesize() helper")
Fixes: 097b9146c0e2 ("net: fix up truesize of cloned skb in skb_prepare_for_shift()")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Marco Elver <elver@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 763087dab97547230a6807c865a6a5ae53a59247 upstream.
We have multiple places where this helper is convenient,
and plan using it in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 901c7280ca0d5e2b4a8929fbe0bfb007ac2a6544 upstream.
Halil Pasic points out [1] that the full revert of that commit (revert
in bddac7c1e02b), and that a partial revert that only reverts the
problematic case, but still keeps some of the cleanups is probably
better. 
And that partial revert [2] had already been verified by Oleksandr
Natalenko to also fix the issue, I had just missed that in the long
discussion.
So let's reinstate the cleanups from commit aa6f8dcbab47 ("swiotlb:
rework "fix info leak with DMA_FROM_DEVICE""), and effectively only
revert the part that caused problems.
Link: https://lore.kernel.org/all/20220328013731.017ae3e3.pasic@linux.ibm.com/ [1]
Link: https://lore.kernel.org/all/20220324055732.GB12078@lst.de/ [2]
Link: https://lore.kernel.org/all/4386660.LvFx2qVVIh@natalenko.name/ [3]
Suggested-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5974ea7ce0f9a5987fc8cf5e08ad6e3e70bb542e upstream.
A NVMe subsystem with multiple controller can have private namespaces
that use the same NSID under some conditions:
"If Namespace Management, ANA Reporting, or NVM Sets are supported, the
NSIDs shall be unique within the NVM subsystem. If the Namespace
Management, ANA Reporting, and NVM Sets are not supported, then NSIDs:
a) for shared namespace shall be unique; and
b) for private namespace are not required to be unique."
Reference: Section 6.1.6 NSID and Namespace Usage; NVM Express 1.4c spec.
Make sure this specific setup is supported in Linux.
Fixes: 9ad1927a3bc2 ("nvme: always search for namespace head")
Signed-off-by: Sungup Moon <sungup.moon@samsung.com>
[hch: refactored and fixed the controller vs subsystem based naming
conflict]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 25795ef6299f07ce3838f3253a9cb34f64efcfae ]
TASK_RTLOCK_WAIT currently isn't part of TASK_REPORT, thus a task blocking
on an rtlock will appear as having a task state == 0, IOW TASK_RUNNING.
The actual state is saved in p->saved_state, but reading it after reading
p->__state has a few issues:
o that could still be TASK_RUNNING in the case of e.g. rt_spin_lock
o ttwu_state_match() might have changed that to TASK_RUNNING
As pointed out by Eric, adding TASK_RTLOCK_WAIT to TASK_REPORT implies
exposing a new state to userspace tools which way not know what to do with
them. The only information that needs to be conveyed here is that a task is
waiting on an rt_mutex, which matches TASK_UNINTERRUPTIBLE - there's no
need for a new state.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20220120162520.570782-3-valentin.schneider@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dc1b4df09acdca7a89806b28f235cd6d8dcd3d24 ]
Arnd reports that on 32-bit architectures, the fallbacks for
atomic64_read_acquire() and atomic64_set_release() are broken as they
use smp_load_acquire() and smp_store_release() respectively, which do
not work on types larger than the native word size.
Since those contain compiletime_assert_atomic_type(), any attempt to use
those fallbacks will result in a build-time error. e.g. with the
following added to arch/arm/kernel/setup.c:
| void test_atomic64(atomic64_t *v)
| {
| atomic64_set_release(v, 5);
| atomic64_read_acquire(v);
| }
The compiler will complain as follows:
| In file included from <command-line>:
| In function 'arch_atomic64_set_release',
| inlined from 'test_atomic64' at ./include/linux/atomic/atomic-instrumented.h:669:2:
| ././include/linux/compiler_types.h:346:38: error: call to '__compiletime_assert_9' declared with attribute error: Need native word sized stores/loads for atomicity.
| 346 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| | ^
| ././include/linux/compiler_types.h:327:4: note: in definition of macro '__compiletime_assert'
| 327 | prefix ## suffix(); \
| | ^~~~~~
| ././include/linux/compiler_types.h:346:2: note: in expansion of macro '_compiletime_assert'
| 346 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| | ^~~~~~~~~~~~~~~~~~~
| ././include/linux/compiler_types.h:349:2: note: in expansion of macro 'compiletime_assert'
| 349 | compiletime_assert(__native_word(t), \
| | ^~~~~~~~~~~~~~~~~~
| ./include/asm-generic/barrier.h:133:2: note: in expansion of macro 'compiletime_assert_atomic_type'
| 133 | compiletime_assert_atomic_type(*p); \
| | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| ./include/asm-generic/barrier.h:164:55: note: in expansion of macro '__smp_store_release'
| 164 | #define smp_store_release(p, v) do { kcsan_release(); __smp_store_release(p, v); } while (0)
| | ^~~~~~~~~~~~~~~~~~~
| ./include/linux/atomic/atomic-arch-fallback.h:1270:2: note: in expansion of macro 'smp_store_release'
| 1270 | smp_store_release(&(v)->counter, i);
| | ^~~~~~~~~~~~~~~~~
| make[2]: *** [scripts/Makefile.build:288: arch/arm/kernel/setup.o] Error 1
| make[1]: *** [scripts/Makefile.build:550: arch/arm/kernel] Error 2
| make: *** [Makefile:1831: arch/arm] Error 2
Fix this by only using smp_load_acquire() and smp_store_release() for
native atomic types, and otherwise falling back to the regular barriers
necessary for acquire/release semantics, as we do in the more generic
acquire and release fallbacks.
Since the fallback templates are used to generate the atomic64_*() and
atomic_*() operations, the __native_word() check is added to both. For
the atomic_*() operations, which are always 32-bit, the __native_word()
check is redundant but not harmful, as it is always true.
For the example above this works as expected on 32-bit, e.g. for arm
multi_v7_defconfig:
| <test_atomic64>:
| push {r4, r5}
| dmb ish
| pldw [r0]
| mov r2, #5
| mov r3, #0
| ldrexd r4, [r0]
| strexd r4, r2, [r0]
| teq r4, #0
| bne 484 <test_atomic64+0x14>
| ldrexd r2, [r0]
| dmb ish
| pop {r4, r5}
| bx lr
... and also on 64-bit, e.g. for arm64 defconfig:
| <test_atomic64>:
| bti c
| paciasp
| mov x1, #0x5
| stlr x1, [x0]
| ldar x0, [x0]
| autiasp
| ret
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/20220207101943.439825-1-mark.rutland@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f58c252e30cf74f68b0054293adc03b5923b9f0e ]
When 8250 UART is using DMA, x_char (XON/XOFF) is never sent
to the wire. After this change, x_char is injected correctly.
Create uart_xchar_out() helper for sending the x_char out and
accounting related to it. It seems that almost every driver
does these same steps with x_char. Except for 8250, however,
almost all currently lack .serial_out so they cannot immediately
take advantage of this new helper.
The downside of this patch is that it might reintroduce
the problems some devices faced with mixed DMA/non-DMA transfer
which caused revert f967fc8f165f (Revert "serial: 8250_dma:
don't bother DMA with small transfers"). However, the impact
should be limited to cases with XON/XOFF (that didn't work
with DMA capable devices to begin with so this problem is not
very likely to cause a major issue, if any at all).
Fixes: 9ee4b83e51f74 ("serial: 8250: Add support for dmaengine")
Reported-by: Gilles Buloz <gilles.buloz@kontron.com>
Tested-by: Gilles Buloz <gilles.buloz@kontron.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220314091432.4288-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 938d3480b92fa5e454b7734294f12a7b75126f09 ]
If tcp_bpf_sendmsg is running during a tear down operation we may enqueue
data on the ingress msg queue while tear down is trying to free it.
sk1 (redirect sk2) sk2
------------------- ---------------
tcp_bpf_sendmsg()
tcp_bpf_send_verdict()
tcp_bpf_sendmsg_redir()
bpf_tcp_ingress()
sock_map_close()
lock_sock()
lock_sock() ... blocking
sk_psock_stop
sk_psock_clear_state(psock, SK_PSOCK_TX_ENABLED);
release_sock(sk);
lock_sock()
sk_mem_charge()
get_page()
sk_psock_queue_msg()
sk_psock_test_state(psock, SK_PSOCK_TX_ENABLED);
drop_sk_msg()
release_sock()
While drop_sk_msg(), the msg has charged memory form sk by sk_mem_charge
and has sg pages need to put. To fix we use sk_msg_free() and then kfee()
msg.
This issue can cause the following info:
WARNING: CPU: 0 PID: 9202 at net/core/stream.c:205 sk_stream_kill_queues+0xc8/0xe0
Call Trace:
<IRQ>
inet_csk_destroy_sock+0x55/0x110
tcp_rcv_state_process+0xe5f/0xe90
? sk_filter_trim_cap+0x10d/0x230
? tcp_v4_do_rcv+0x161/0x250
tcp_v4_do_rcv+0x161/0x250
tcp_v4_rcv+0xc3a/0xce0
ip_protocol_deliver_rcu+0x3d/0x230
ip_local_deliver_finish+0x54/0x60
ip_local_deliver+0xfd/0x110
? ip_protocol_deliver_rcu+0x230/0x230
ip_rcv+0xd6/0x100
? ip_local_deliver+0x110/0x110
__netif_receive_skb_one_core+0x85/0xa0
process_backlog+0xa4/0x160
__napi_poll+0x29/0x1b0
net_rx_action+0x287/0x300
__do_softirq+0xff/0x2fc
do_softirq+0x79/0x90
</IRQ>
WARNING: CPU: 0 PID: 531 at net/ipv4/af_inet.c:154 inet_sock_destruct+0x175/0x1b0
Call Trace:
<TASK>
__sk_destruct+0x24/0x1f0
sk_psock_destroy+0x19b/0x1c0
process_one_work+0x1b3/0x3c0
? process_one_work+0x3c0/0x3c0
worker_thread+0x30/0x350
? process_one_work+0x3c0/0x3c0
kthread+0xe6/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
</TASK>
Fixes: 9635720b7c88 ("bpf, sockmap: Fix memleak on ingress msg enqueue")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220304081145.2037182-2-wangyufen@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 92c45b63ce22c8898aa41806e8d6692bcd577510 ]
For hardware that only supports 32-bit writes to PCI there is the
possibility of clearing RW1C (write-one-to-clear) bits. A rate-limited
messages was introduced by fb2659230120, but rate-limiting is not the best
choice here. Some devices may not show the warnings they should if another
device has just produced a bunch of warnings. Also, the number of messages
can be a nuisance on devices which are otherwise working fine.
Change the ratelimit to a single warning per bus. This ensures no bus is
'starved' of emitting a warning and also that there isn't a continuous
stream of warnings. It would be preferable to have a warning per device,
but the pci_dev structure is not available here, and a lookup from devfn
would be far too slow.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Fixes: fb2659230120 ("PCI: Warn on possible RW1C corruption for sub-32 bit config writes")
Link: https://lore.kernel.org/r/20200806041455.11070-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
defined
[ Upstream commit 043cfff99a18933fda2fb2e163daee73cc07910b ]
Remove an extra ";" which breaks compilation.
Fixes: 53bf2b0e4e4c ("firmware: ti_sci: Add support for getting resource with subtype")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/e6c3cb793e1a6a2a0ae2528d5a5650dfe6a4b6ff.1640276505.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit efa90c11f62e6b7252fb75efe2787056872a627c ]
All supported versions of Clang perform auto-init of __builtin_alloca()
when stack auto-init is on (CONFIG_INIT_STACK_ALL_{ZERO,PATTERN}).
add_random_kstack_offset() uses __builtin_alloca() to add a stack
offset. This means, when CONFIG_INIT_STACK_ALL_{ZERO,PATTERN} is
enabled, add_random_kstack_offset() will auto-init that unused portion
of the stack used to add an offset.
There are several problems with this:
1. These offsets can be as large as 1023 bytes. Performing
memset() on them isn't exactly cheap, and this is done on
every syscall entry.
2. Architectures adding add_random_kstack_offset() to syscall
entry implemented in C require them to be 'noinstr' (e.g. see
x86 and s390). The potential problem here is that a call to
memset may occur, which is not noinstr.
A x86_64 defconfig kernel with Clang 11 and CONFIG_VMLINUX_VALIDATION shows:
| vmlinux.o: warning: objtool: do_syscall_64()+0x9d: call to memset() leaves .noinstr.text section
| vmlinux.o: warning: objtool: do_int80_syscall_32()+0xab: call to memset() leaves .noinstr.text section
| vmlinux.o: warning: objtool: __do_fast_syscall_32()+0xe2: call to memset() leaves .noinstr.text section
| vmlinux.o: warning: objtool: fixup_bad_iret()+0x2f: call to memset() leaves .noinstr.text section
Clang 14 (unreleased) will introduce a way to skip alloca initialization
via __builtin_alloca_uninitialized() (https://reviews.llvm.org/D115440).
Constrain RANDOMIZE_KSTACK_OFFSET to only be enabled if no stack
auto-init is enabled, the compiler is GCC, or Clang is version 14+. Use
__builtin_alloca_uninitialized() if the compiler provides it, as is done
by Clang 14.
Link: https://lkml.kernel.org/r/YbHTKUjEejZCLyhX@elver.google.com
Fixes: 39218ff4c625 ("stack: Optionally randomize kernel stack offset each syscall")
Signed-off-by: Marco Elver <elver@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220131090521.1947110-2-elver@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
