| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The verifier only enumerates valid control-flow paths and skips paths that
are unreachable in the non-speculative domain. And so it can miss issues
under speculative execution on mispredicted branches.
For example, a type confusion has been demonstrated with the following
crafted program:
// r0 = pointer to a map array entry
// r6 = pointer to readable stack slot
// r9 = scalar controlled by attacker
1: r0 = *(u64 *)(r0) // cache miss
2: if r0 != 0x0 goto line 4
3: r6 = r9
4: if r0 != 0x1 goto line 6
5: r9 = *(u8 *)(r6)
6: // leak r9
Since line 3 runs iff r0 == 0 and line 5 runs iff r0 == 1, the verifier
concludes that the pointer dereference on line 5 is safe. But: if the
attacker trains both the branches to fall-through, such that the following
is speculatively executed ...
r6 = r9
r9 = *(u8 *)(r6)
// leak r9
... then the program will dereference an attacker-controlled value and could
leak its content under speculative execution via side-channel. This requires
to mistrain the branch predictor, which can be rather tricky, because the
branches are mutually exclusive. However such training can be done at
congruent addresses in user space using different branches that are not
mutually exclusive. That is, by training branches in user space ...
A: if r0 != 0x0 goto line C
B: ...
C: if r0 != 0x0 goto line D
D: ...
... such that addresses A and C collide to the same CPU branch prediction
entries in the PHT (pattern history table) as those of the BPF program's
lines 2 and 4, respectively. A non-privileged attacker could simply brute
force such collisions in the PHT until observing the attack succeeding.
Alternative methods to mistrain the branch predictor are also possible that
avoid brute forcing the collisions in the PHT. A reliable attack has been
demonstrated, for example, using the following crafted program:
// r0 = pointer to a [control] map array entry
// r7 = *(u64 *)(r0 + 0), training/attack phase
// r8 = *(u64 *)(r0 + 8), oob address
// [...]
// r0 = pointer to a [data] map array entry
1: if r7 == 0x3 goto line 3
2: r8 = r0
// crafted sequence of conditional jumps to separate the conditional
// branch in line 193 from the current execution flow
3: if r0 != 0x0 goto line 5
4: if r0 == 0x0 goto exit
5: if r0 != 0x0 goto line 7
6: if r0 == 0x0 goto exit
[...]
187: if r0 != 0x0 goto line 189
188: if r0 == 0x0 goto exit
// load any slowly-loaded value (due to cache miss in phase 3) ...
189: r3 = *(u64 *)(r0 + 0x1200)
// ... and turn it into known zero for verifier, while preserving slowly-
// loaded dependency when executing:
190: r3 &= 1
191: r3 &= 2
// speculatively bypassed phase dependency
192: r7 += r3
193: if r7 == 0x3 goto exit
194: r4 = *(u8 *)(r8 + 0)
// leak r4
As can be seen, in training phase (phase != 0x3), the condition in line 1
turns into false and therefore r8 with the oob address is overridden with
the valid map value address, which in line 194 we can read out without
issues. However, in attack phase, line 2 is skipped, and due to the cache
miss in line 189 where the map value is (zeroed and later) added to the
phase register, the condition in line 193 takes the fall-through path due
to prior branch predictor training, where under speculation, it'll load the
byte at oob address r8 (unknown scalar type at that point) which could then
be leaked via side-channel.
One way to mitigate these is to 'branch off' an unreachable path, meaning,
the current verification path keeps following the is_branch_taken() path
and we push the other branch to the verification stack. Given this is
unreachable from the non-speculative domain, this branch's vstate is
explicitly marked as speculative. This is needed for two reasons: i) if
this path is solely seen from speculative execution, then we later on still
want the dead code elimination to kick in in order to sanitize these
instructions with jmp-1s, and ii) to ensure that paths walked in the
non-speculative domain are not pruned from earlier walks of paths walked in
the speculative domain. Additionally, for robustness, we mark the registers
which have been part of the conditional as unknown in the speculative path
given there should be no assumptions made on their content.
The fix in here mitigates type confusion attacks described earlier due to
i) all code paths in the BPF program being explored and ii) existing
verifier logic already ensuring that given memory access instruction
references one specific data structure.
An alternative to this fix that has also been looked at in this scope was to
mark aux->alu_state at the jump instruction with a BPF_JMP_TAKEN state as
well as direction encoding (always-goto, always-fallthrough, unknown), such
that mixing of different always-* directions themselves as well as mixing of
always-* with unknown directions would cause a program rejection by the
verifier, e.g. programs with constructs like 'if ([...]) { x = 0; } else
{ x = 1; }' with subsequent 'if (x == 1) { [...] }'. For unprivileged, this
would result in only single direction always-* taken paths, and unknown taken
paths being allowed, such that the former could be patched from a conditional
jump to an unconditional jump (ja). Compared to this approach here, it would
have two downsides: i) valid programs that otherwise are not performing any
pointer arithmetic, etc, would potentially be rejected/broken, and ii) we are
required to turn off path pruning for unprivileged, where both can be avoided
in this work through pushing the invalid branch to the verification stack.
The issue was originally discovered by Adam and Ofek, and later independently
discovered and reported as a result of Benedict and Piotr's research work.
Fixes: b2157399cc98 ("bpf: prevent out-of-bounds speculation")
Reported-by: Adam Morrison <mad@cs.tau.ac.il>
Reported-by: Ofek Kirzner <ofekkir@gmail.com>
Reported-by: Benedict Schlueter <benedict.schlueter@rub.de>
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
... in such circumstances, we do not want to mark the instruction as seen given
the goal is still to jmp-1 rewrite/sanitize dead code, if it is not reachable
from the non-speculative path verification. We do however want to verify it for
safety regardless.
With the patch as-is all the insns that have been marked as seen before the
patch will also be marked as seen after the patch (just with a potentially
different non-zero count). An upcoming patch will also verify paths that are
unreachable in the non-speculative domain, hence this extension is needed.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Instead of relying on current env->pass_cnt, use the seen count from the
old aux data in adjust_insn_aux_data(), and expand it to the new range of
patched instructions. This change is valid given we always expand 1:n
with n>=1, so what applies to the old/original instruction needs to apply
for the replacement as well.
Not relying on env->pass_cnt is a prerequisite for a later change where we
want to avoid marking an instruction seen when verified under speculative
execution path.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Commit 59438b46471a ("security,lockdown,selinux: implement SELinux lockdown")
added an implementation of the locked_down LSM hook to SELinux, with the aim
to restrict which domains are allowed to perform operations that would breach
lockdown. This is indirectly also getting audit subsystem involved to report
events. The latter is problematic, as reported by Ondrej and Serhei, since it
can bring down the whole system via audit:
1) The audit events that are triggered due to calls to security_locked_down()
can OOM kill a machine, see below details [0].
2) It also seems to be causing a deadlock via avc_has_perm()/slow_avc_audit()
when trying to wake up kauditd, for example, when using trace_sched_switch()
tracepoint, see details in [1]. Triggering this was not via some hypothetical
corner case, but with existing tools like runqlat & runqslower from bcc, for
example, which make use of this tracepoint. Rough call sequence goes like:
rq_lock(rq) -> -------------------------+
trace_sched_switch() -> |
bpf_prog_xyz() -> +-> deadlock
selinux_lockdown() -> |
audit_log_end() -> |
wake_up_interruptible() -> |
try_to_wake_up() -> |
rq_lock(rq) --------------+
What's worse is that the intention of 59438b46471a to further restrict lockdown
settings for specific applications in respect to the global lockdown policy is
completely broken for BPF. The SELinux policy rule for the current lockdown check
looks something like this:
allow <who> <who> : lockdown { <reason> };
However, this doesn't match with the 'current' task where the security_locked_down()
is executed, example: httpd does a syscall. There is a tracing program attached
to the syscall which triggers a BPF program to run, which ends up doing a
bpf_probe_read_kernel{,_str}() helper call. The selinux_lockdown() hook does
the permission check against 'current', that is, httpd in this example. httpd
has literally zero relation to this tracing program, and it would be nonsensical
having to write an SELinux policy rule against httpd to let the tracing helper
pass. The policy in this case needs to be against the entity that is installing
the BPF program. For example, if bpftrace would generate a histogram of syscall
counts by user space application:
bpftrace -e 'tracepoint:raw_syscalls:sys_enter { @[comm] = count(); }'
bpftrace would then go and generate a BPF program from this internally. One way
of doing it [for the sake of the example] could be to call bpf_get_current_task()
helper and then access current->comm via one of bpf_probe_read_kernel{,_str}()
helpers. So the program itself has nothing to do with httpd or any other random
app doing a syscall here. The BPF program _explicitly initiated_ the lockdown
check. The allow/deny policy belongs in the context of bpftrace: meaning, you
want to grant bpftrace access to use these helpers, but other tracers on the
system like my_random_tracer _not_.
Therefore fix all three issues at the same time by taking a completely different
approach for the security_locked_down() hook, that is, move the check into the
program verification phase where we actually retrieve the BPF func proto. This
also reliably gets the task (current) that is trying to install the BPF tracing
program, e.g. bpftrace/bcc/perf/systemtap/etc, and it also fixes the OOM since
we're moving this out of the BPF helper's fast-path which can be called several
millions of times per second.
The check is then also in line with other security_locked_down() hooks in the
system where the enforcement is performed at open/load time, for example,
open_kcore() for /proc/kcore access or module_sig_check() for module signatures
just to pick few random ones. What's out of scope in the fix as well as in
other security_locked_down() hook locations /outside/ of BPF subsystem is that
if the lockdown policy changes on the fly there is no retrospective action.
This requires a different discussion, potentially complex infrastructure, and
it's also not clear whether this can be solved generically. Either way, it is
out of scope for a suitable stable fix which this one is targeting. Note that
the breakage is specifically on 59438b46471a where it started to rely on 'current'
as UAPI behavior, and _not_ earlier infrastructure such as 9d1f8be5cf42 ("bpf:
Restrict bpf when kernel lockdown is in confidentiality mode").
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1955585, Jakub Hrozek says:
I starting seeing this with F-34. When I run a container that is traced with
BPF to record the syscalls it is doing, auditd is flooded with messages like:
type=AVC msg=audit(1619784520.593:282387): avc: denied { confidentiality }
for pid=476 comm="auditd" lockdown_reason="use of bpf to read kernel RAM"
scontext=system_u:system_r:auditd_t:s0 tcontext=system_u:system_r:auditd_t:s0
tclass=lockdown permissive=0
This seems to be leading to auditd running out of space in the backlog buffer
and eventually OOMs the machine.
[...]
auditd running at 99% CPU presumably processing all the messages, eventually I get:
Apr 30 12:20:42 fedora kernel: audit: backlog limit exceeded
Apr 30 12:20:42 fedora kernel: audit: backlog limit exceeded
Apr 30 12:20:42 fedora kernel: audit: audit_backlog=2152579 > audit_backlog_limit=64
Apr 30 12:20:42 fedora kernel: audit: audit_backlog=2152626 > audit_backlog_limit=64
Apr 30 12:20:42 fedora kernel: audit: audit_backlog=2152694 > audit_backlog_limit=64
Apr 30 12:20:42 fedora kernel: audit: audit_lost=6878426 audit_rate_limit=0 audit_backlog_limit=64
Apr 30 12:20:45 fedora kernel: oci-seccomp-bpf invoked oom-killer: gfp_mask=0x100cca(GFP_HIGHUSER_MOVABLE), order=0, oom_score_adj=-1000
Apr 30 12:20:45 fedora kernel: CPU: 0 PID: 13284 Comm: oci-seccomp-bpf Not tainted 5.11.12-300.fc34.x86_64 #1
Apr 30 12:20:45 fedora kernel: Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
[...]
[1] https://lore.kernel.org/linux-audit/CANYvDQN7H5tVp47fbYcRasv4XF07eUbsDwT_eDCHXJUj43J7jQ@mail.gmail.com/,
Serhei Makarov says:
Upstream kernel 5.11.0-rc7 and later was found to deadlock during a
bpf_probe_read_compat() call within a sched_switch tracepoint. The problem
is reproducible with the reg_alloc3 testcase from SystemTap's BPF backend
testsuite on x86_64 as well as the runqlat, runqslower tools from bcc on
ppc64le. Example stack trace:
[...]
[ 730.868702] stack backtrace:
[ 730.869590] CPU: 1 PID: 701 Comm: in:imjournal Not tainted, 5.12.0-0.rc2.20210309git144c79ef3353.166.fc35.x86_64 #1
[ 730.871605] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
[ 730.873278] Call Trace:
[ 730.873770] dump_stack+0x7f/0xa1
[ 730.874433] check_noncircular+0xdf/0x100
[ 730.875232] __lock_acquire+0x1202/0x1e10
[ 730.876031] ? __lock_acquire+0xfc0/0x1e10
[ 730.876844] lock_acquire+0xc2/0x3a0
[ 730.877551] ? __wake_up_common_lock+0x52/0x90
[ 730.878434] ? lock_acquire+0xc2/0x3a0
[ 730.879186] ? lock_is_held_type+0xa7/0x120
[ 730.880044] ? skb_queue_tail+0x1b/0x50
[ 730.880800] _raw_spin_lock_irqsave+0x4d/0x90
[ 730.881656] ? __wake_up_common_lock+0x52/0x90
[ 730.882532] __wake_up_common_lock+0x52/0x90
[ 730.883375] audit_log_end+0x5b/0x100
[ 730.884104] slow_avc_audit+0x69/0x90
[ 730.884836] avc_has_perm+0x8b/0xb0
[ 730.885532] selinux_lockdown+0xa5/0xd0
[ 730.886297] security_locked_down+0x20/0x40
[ 730.887133] bpf_probe_read_compat+0x66/0xd0
[ 730.887983] bpf_prog_250599c5469ac7b5+0x10f/0x820
[ 730.888917] trace_call_bpf+0xe9/0x240
[ 730.889672] perf_trace_run_bpf_submit+0x4d/0xc0
[ 730.890579] perf_trace_sched_switch+0x142/0x180
[ 730.891485] ? __schedule+0x6d8/0xb20
[ 730.892209] __schedule+0x6d8/0xb20
[ 730.892899] schedule+0x5b/0xc0
[ 730.893522] exit_to_user_mode_prepare+0x11d/0x240
[ 730.894457] syscall_exit_to_user_mode+0x27/0x70
[ 730.895361] entry_SYSCALL_64_after_hwframe+0x44/0xae
[...]
Fixes: 59438b46471a ("security,lockdown,selinux: implement SELinux lockdown")
Reported-by: Ondrej Mosnacek <omosnace@redhat.com>
Reported-by: Jakub Hrozek <jhrozek@redhat.com>
Reported-by: Serhei Makarov <smakarov@redhat.com>
Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: James Morris <jamorris@linux.microsoft.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Frank Eigler <fche@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/bpf/01135120-8bf7-df2e-cff0-1d73f1f841c3@iogearbox.net
|
|
In 801c6058d14a ("bpf: Fix leakage of uninitialized bpf stack under
speculation") we replaced masking logic with direct loads of immediates
if the register is a known constant. Given in this case we do not apply
any masking, there is also no reason for the operation to be truncated
under the speculative domain.
Therefore, there is also zero reason for the verifier to branch-off and
simulate this case, it only needs to do it for unknown but bounded scalars.
As a side-effect, this also enables few test cases that were previously
rejected due to simulation under zero truncation.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Masking direction as indicated via mask_to_left is considered to be
calculated once and then used to derive pointer limits. Thus, this
needs to be placed into bpf_sanitize_info instead so we can pass it
to sanitize_ptr_alu() call after the pointer move. Piotr noticed a
corner case where the off reg causes masking direction change which
then results in an incorrect final aux->alu_limit.
Fixes: 7fedb63a8307 ("bpf: Tighten speculative pointer arithmetic mask")
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add a container structure struct bpf_sanitize_info which holds
the current aux info, and update call-sites to sanitize_ptr_alu()
to pass it in. This is needed for passing in additional state
later on.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Similarly as 6bdacdb48e94 ("bpf: Fix BPF_JIT kconfig symbol dependency") we
need to detangle the hard BPF_LSM dependency on NET. This was previously
implicit by its dependency on BPF_JIT which itself was dependent on NET (but
without any actual/real hard dependency code-wise). Given the latter was
lifted, so should be the former as BPF_LSMs could well exist on net-less
systems. This therefore also fixes a randconfig build error recently reported
by Randy:
ld: kernel/bpf/bpf_lsm.o: in function `bpf_lsm_func_proto':
bpf_lsm.c:(.text+0x1a0): undefined reference to `bpf_sk_storage_get_proto'
ld: bpf_lsm.c:(.text+0x1b8): undefined reference to `bpf_sk_storage_delete_proto'
[...]
Fixes: b24abcff918a ("bpf, kconfig: Add consolidated menu entry for bpf with core options")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
|
|
Commit 4976b718c355 ("bpf: Introduce pseudo_btf_id") switched the
order of resolve_pseudo_ldimm(), in which some pseudo instructions
are rewritten. Thus those rewritten instructions cannot be passed
to driver via 'prepare' offload callback.
Reorder the 'prepare' offload callback to fix it.
Fixes: 4976b718c355 ("bpf: Introduce pseudo_btf_id")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210520085834.15023-1-simon.horman@netronome.com
|
|
The cppcheck static code analysis reported the following error:
if (WARN_ON_ONCE(nest_level > ARRAY_SIZE(bufs->tmp_bufs))) {
^
ARRAY_SIZE is a macro that expands to sizeofs, so bufs is not actually
dereferenced at runtime, and the code is actually safe. But to keep
things tidy, this patch removes the need for a call to ARRAY_SIZE by
extracting the size of the array into a macro. Cppcheck should no longer
be confused and the code ends up being a bit cleaner.
Fixes: e2d5b2bb769f ("bpf: Fix nested bpf_bprintf_prepare with more per-cpu buffers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20210517092830.1026418-2-revest@chromium.org
|
|
The per-cpu buffers contain bprintf data rather than printf arguments.
The macro name and comment were a bit confusing, this rewords them in a
clearer way.
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20210517092830.1026418-1-revest@chromium.org
|
|
Randy reported a randconfig build error recently on i386:
ld: arch/x86/net/bpf_jit_comp32.o: in function `do_jit':
bpf_jit_comp32.c:(.text+0x28c9): undefined reference to `__bpf_call_base'
ld: arch/x86/net/bpf_jit_comp32.o: in function `bpf_int_jit_compile':
bpf_jit_comp32.c:(.text+0x3694): undefined reference to `bpf_jit_blind_constants'
ld: bpf_jit_comp32.c:(.text+0x3719): undefined reference to `bpf_jit_binary_free'
ld: bpf_jit_comp32.c:(.text+0x3745): undefined reference to `bpf_jit_binary_alloc'
ld: bpf_jit_comp32.c:(.text+0x37d3): undefined reference to `bpf_jit_prog_release_other'
[...]
The cause was that b24abcff918a ("bpf, kconfig: Add consolidated menu entry for
bpf with core options") moved BPF_JIT from net/Kconfig into kernel/bpf/Kconfig
and previously BPF_JIT was guarded by a 'if NET'. However, there is no actual
dependency on NET, it's just that menuconfig NET selects BPF. And the latter in
turn causes kernel/bpf/core.o to be built which contains above symbols. Randy's
randconfig didn't have NET set, and BPF wasn't either, but BPF_JIT otoh was.
Detangle this by making BPF_JIT depend on BPF instead. arm64 was the only arch
that pulled in its JIT in net/ via obj-$(CONFIG_NET), all others unconditionally
pull this dir in via obj-y. Do the same since CONFIG_NET guard there is really
useless as we compiled the JIT via obj-$(CONFIG_BPF_JIT) += bpf_jit_comp.o anyway.
Fixes: b24abcff918a ("bpf, kconfig: Add consolidated menu entry for bpf with core options")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
|
|
The bpf_seq_printf, bpf_trace_printk and bpf_snprintf helpers share one
per-cpu buffer that they use to store temporary data (arguments to
bprintf). They "get" that buffer with try_get_fmt_tmp_buf and "put" it
by the end of their scope with bpf_bprintf_cleanup.
If one of these helpers gets called within the scope of one of these
helpers, for example: a first bpf program gets called, uses
bpf_trace_printk which calls raw_spin_lock_irqsave which is traced by
another bpf program that calls bpf_snprintf, then the second "get"
fails. Essentially, these helpers are not re-entrant. They would return
-EBUSY and print a warning message once.
This patch triples the number of bprintf buffers to allow three levels
of nesting. This is very similar to what was done for tracepoints in
"9594dc3c7e7 bpf: fix nested bpf tracepoints with per-cpu data"
Fixes: d9c9e4db186a ("bpf: Factorize bpf_trace_printk and bpf_seq_printf")
Reported-by: syzbot+63122d0bc347f18c1884@syzkaller.appspotmail.com
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210511081054.2125874-1-revest@chromium.org
|
|
The recursion check in __bpf_prog_enter and __bpf_prog_exit
leaves some (not inlined) functions unprotected:
In __bpf_prog_enter:
- migrate_disable is called before prog->active is checked
In __bpf_prog_exit:
- migrate_enable,rcu_read_unlock_strict are called after
prog->active is decreased
When attaching trampoline to them we get panic like:
traps: PANIC: double fault, error_code: 0x0
double fault: 0000 [#1] SMP PTI
RIP: 0010:__bpf_prog_enter+0x4/0x50
...
Call Trace:
<IRQ>
bpf_trampoline_6442466513_0+0x18/0x1000
migrate_disable+0x5/0x50
__bpf_prog_enter+0x9/0x50
bpf_trampoline_6442466513_0+0x18/0x1000
migrate_disable+0x5/0x50
__bpf_prog_enter+0x9/0x50
bpf_trampoline_6442466513_0+0x18/0x1000
migrate_disable+0x5/0x50
__bpf_prog_enter+0x9/0x50
bpf_trampoline_6442466513_0+0x18/0x1000
migrate_disable+0x5/0x50
...
Fixing this by adding deny list of btf ids for tracing
programs and checking btf id during program verification.
Adding above functions to this list.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210429114712.43783-1-jolsa@kernel.org
|
|
Add a kconfig knob which allows for unprivileged bpf to be disabled by default.
If set, the knob sets /proc/sys/kernel/unprivileged_bpf_disabled to value of 2.
This still allows a transition of 2 -> {0,1} through an admin. Similarly,
this also still keeps 1 -> {1} behavior intact, so that once set to permanently
disabled, it cannot be undone aside from a reboot.
We've also added extra2 with max of 2 for the procfs handler, so that an admin
still has a chance to toggle between 0 <-> 2.
Either way, as an additional alternative, applications can make use of CAP_BPF
that we added a while ago.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/74ec548079189e4e4dffaeb42b8987bb3c852eee.1620765074.git.daniel@iogearbox.net
|
|
Right now, all core BPF related options are scattered in different Kconfig
locations mainly due to historic reasons. Moving forward, lets add a proper
subsystem entry under ...
General setup --->
BPF subsystem --->
... in order to have all knobs in a single location and thus ease BPF related
configuration. Networking related bits such as sockmap are out of scope for
the general setup and therefore better suited to remain in net/Kconfig.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/f23f58765a4d59244ebd8037da7b6a6b2fb58446.1620765074.git.daniel@iogearbox.net
|
|
Only the very first page of BPF ringbuf that contains consumer position
counter is supposed to be mapped as writeable by user-space. Producer
position is read-only and can be modified only by the kernel code. BPF ringbuf
data pages are read-only as well and are not meant to be modified by
user-code to maintain integrity of per-record headers.
This patch allows to map only consumer position page as writeable and
everything else is restricted to be read-only. remap_vmalloc_range()
internally adds VM_DONTEXPAND, so all the established memory mappings can't be
extended, which prevents any future violations through mremap()'ing.
Fixes: 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support for it")
Reported-by: Ryota Shiga (Flatt Security)
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
A BPF program might try to reserve a buffer larger than the ringbuf size.
If the consumer pointer is way ahead of the producer, that would be
successfully reserved, allowing the BPF program to read or write out of
the ringbuf allocated area.
Reported-by: Ryota Shiga (Flatt Security)
Fixes: 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support for it")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Fix a bug in the verifier's scalar32_min_max_*() functions which leads to
incorrect tracking of 32 bit bounds for the simulation of and/or/xor bitops.
When both the src & dst subreg is a known constant, then the assumption is
that scalar_min_max_*() will take care to update bounds correctly. However,
this is not the case, for example, consider a register R2 which has a tnum
of 0xffffffff00000000, meaning, lower 32 bits are known constant and in this
case of value 0x00000001. R2 is then and'ed with a register R3 which is a
64 bit known constant, here, 0x100000002.
What can be seen in line '10:' is that 32 bit bounds reach an invalid state
where {u,s}32_min_value > {u,s}32_max_value. The reason is scalar32_min_max_*()
delegates 32 bit bounds updates to scalar_min_max_*(), however, that really
only takes place when both the 64 bit src & dst register is a known constant.
Given scalar32_min_max_*() is intended to be designed as closely as possible
to scalar_min_max_*(), update the 32 bit bounds in this situation through
__mark_reg32_known() which will set all {u,s}32_{min,max}_value to the correct
constant, which is 0x00000000 after the fix (given 0x00000001 & 0x00000002 in
32 bit space). This is possible given var32_off already holds the final value
as dst_reg->var_off is updated before calling scalar32_min_max_*().
Before fix, invalid tracking of R2:
[...]
9: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=-9223372036854775807 (0x8000000000000001),smax_value=9223372032559808513 (0x7fffffff00000001),umin_value=1,umax_value=0xffffffff00000001,var_off=(0x1; 0xffffffff00000000),s32_min_value=1,s32_max_value=1,u32_min_value=1,u32_max_value=1) R3_w=inv4294967298 R10=fp0
9: (5f) r2 &= r3
10: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=0,smax_value=4294967296 (0x100000000),umin_value=0,umax_value=0x100000000,var_off=(0x0; 0x100000000),s32_min_value=1,s32_max_value=0,u32_min_value=1,u32_max_value=0) R3_w=inv4294967298 R10=fp0
[...]
After fix, correct tracking of R2:
[...]
9: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=-9223372036854775807 (0x8000000000000001),smax_value=9223372032559808513 (0x7fffffff00000001),umin_value=1,umax_value=0xffffffff00000001,var_off=(0x1; 0xffffffff00000000),s32_min_value=1,s32_max_value=1,u32_min_value=1,u32_max_value=1) R3_w=inv4294967298 R10=fp0
9: (5f) r2 &= r3
10: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=0,smax_value=4294967296 (0x100000000),umin_value=0,umax_value=0x100000000,var_off=(0x0; 0x100000000),s32_min_value=0,s32_max_value=0,u32_min_value=0,u32_max_value=0) R3_w=inv4294967298 R10=fp0
[...]
Fixes: 3f50f132d840 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Fixes: 2921c90d4718 ("bpf: Fix a verifier failure with xor")
Reported-by: Manfred Paul (@_manfp)
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
We can't currently allow to attach functions with variable arguments.
The problem is that we should save all the registers for arguments,
which is probably doable, but if caller uses more than 6 arguments,
we need stack data, which will be wrong, because of the extra stack
frame we do in bpf trampoline, so we could crash.
Also currently there's malformed trampoline code generated for such
functions at the moment as described in:
https://lore.kernel.org/bpf/20210429212834.82621-1-jolsa@kernel.org/
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210505132529.401047-1-jolsa@kernel.org
|
|
The current implemented mechanisms to mitigate data disclosure under
speculation mainly address stack and map value oob access from the
speculative domain. However, Piotr discovered that uninitialized BPF
stack is not protected yet, and thus old data from the kernel stack,
potentially including addresses of kernel structures, could still be
extracted from that 512 bytes large window. The BPF stack is special
compared to map values since it's not zero initialized for every
program invocation, whereas map values /are/ zero initialized upon
their initial allocation and thus cannot leak any prior data in either
domain. In the non-speculative domain, the verifier ensures that every
stack slot read must have a prior stack slot write by the BPF program
to avoid such data leaking issue.
However, this is not enough: for example, when the pointer arithmetic
operation moves the stack pointer from the last valid stack offset to
the first valid offset, the sanitation logic allows for any intermediate
offsets during speculative execution, which could then be used to
extract any restricted stack content via side-channel.
Given for unprivileged stack pointer arithmetic the use of unknown
but bounded scalars is generally forbidden, we can simply turn the
register-based arithmetic operation into an immediate-based arithmetic
operation without the need for masking. This also gives the benefit
of reducing the needed instructions for the operation. Given after
the work in 7fedb63a8307 ("bpf: Tighten speculative pointer arithmetic
mask"), the aux->alu_limit already holds the final immediate value for
the offset register with the known scalar. Thus, a simple mov of the
immediate to AX register with using AX as the source for the original
instruction is sufficient and possible now in this case.
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
The negation logic for the case where the off_reg is sitting in the
dst register is not correct given then we cannot just invert the add
to a sub or vice versa. As a fix, perform the final bitwise and-op
unconditionally into AX from the off_reg, then move the pointer from
the src to dst and finally use AX as the source for the original
pointer arithmetic operation such that the inversion yields a correct
result. The single non-AX mov in between is possible given constant
blinding is retaining it as it's not an immediate based operation.
Fixes: 979d63d50c0c ("bpf: prevent out of bounds speculation on pointer arithmetic")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
|
|
Uses the already in-place infrastructure provided by the
'generic_map_*_batch' functions.
No tweak was needed as it transparently handles the percpu variant.
As arrays don't have delete operations, let it return a error to
user space (default behaviour).
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210424214510.806627-2-pctammela@mojatatu.com
|
|
BPF has three formatted output helpers: bpf_trace_printk, bpf_seq_printf
and bpf_snprintf. Their signatures specify that all arguments are
provided from the BPF world as u64s (in an array or as registers). All
of these helpers are currently implemented by calling functions such as
snprintf() whose signatures take a variable number of arguments, then
placed in a va_list by the compiler to call vsnprintf().
"d9c9e4db bpf: Factorize bpf_trace_printk and bpf_seq_printf" introduced
a bpf_printf_prepare function that fills an array of u64 sanitized
arguments with an array of "modifiers" which indicate what the "real"
size of each argument should be (given by the format specifier). The
BPF_CAST_FMT_ARG macro consumes these arrays and casts each argument to
its real size. However, the C promotion rules implicitely cast them all
back to u64s. Therefore, the arguments given to snprintf are u64s and
the va_list constructed by the compiler will use 64 bits for each
argument. On 64 bit machines, this happens to work well because 32 bit
arguments in va_lists need to occupy 64 bits anyway, but on 32 bit
architectures this breaks the layout of the va_list expected by the
called function and mangles values.
In "88a5c690b6 bpf: fix bpf_trace_printk on 32 bit archs", this problem
had been solved for bpf_trace_printk only with a "horrid workaround"
that emitted multiple calls to trace_printk where each call had
different argument types and generated different va_list layouts. One of
the call would be dynamically chosen at runtime. This was ok with the 3
arguments that bpf_trace_printk takes but bpf_seq_printf and
bpf_snprintf accept up to 12 arguments. Because this approach scales
code exponentially, it is not a viable option anymore.
Because the promotion rules are part of the language and because the
construction of a va_list is an arch-specific ABI, it's best to just
avoid variadic arguments and va_lists altogether. Thankfully the
kernel's snprintf() has an alternative in the form of bstr_printf() that
accepts arguments in a "binary buffer representation". These binary
buffers are currently created by vbin_printf and used in the tracing
subsystem to split the cost of printing into two parts: a fast one that
only dereferences and remembers values, and a slower one, called later,
that does the pretty-printing.
This patch refactors bpf_printf_prepare to construct binary buffers of
arguments consumable by bstr_printf() instead of arrays of arguments and
modifiers. This gets rid of BPF_CAST_FMT_ARG and greatly simplifies the
bpf_printf_prepare usage but there are a few gotchas that change how
bpf_printf_prepare needs to do things.
Currently, bpf_printf_prepare uses a per cpu temporary buffer as a
generic storage for strings and IP addresses. With this refactoring, the
temporary buffers now holds all the arguments in a structured binary
format.
To comply with the format expected by bstr_printf, certain format
specifiers also need to be pre-formatted: %pB and %pi6/%pi4/%pI4/%pI6.
Because vsnprintf subroutines for these specifiers are hard to expose,
we pre-format these arguments with calls to snprintf().
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210427174313.860948-3-revest@chromium.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux updates from Paul Moore:
- Add support for measuring the SELinux state and policy capabilities
using IMA.
- A handful of SELinux/NFS patches to compare the SELinux state of one
mount with a set of mount options. Olga goes into more detail in the
patch descriptions, but this is important as it allows more
flexibility when using NFS and SELinux context mounts.
- Properly differentiate between the subjective and objective LSM
credentials; including support for the SELinux and Smack. My clumsy
attempt at a proper fix for AppArmor didn't quite pass muster so John
is working on a proper AppArmor patch, in the meantime this set of
patches shouldn't change the behavior of AppArmor in any way. This
change explains the bulk of the diffstat beyond security/.
- Fix a problem where we were not properly terminating the permission
list for two SELinux object classes.
* tag 'selinux-pr-20210426' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: add proper NULL termination to the secclass_map permissions
smack: differentiate between subjective and objective task credentials
selinux: clarify task subjective and objective credentials
lsm: separate security_task_getsecid() into subjective and objective variants
nfs: account for selinux security context when deciding to share superblock
nfs: remove unneeded null check in nfs_fill_super()
lsm,selinux: add new hook to compare new mount to an existing mount
selinux: fix misspellings using codespell tool
selinux: fix misspellings using codespell tool
selinux: measure state and policy capabilities
selinux: Allow context mounts for unpriviliged overlayfs
|
|
Rely on netif_receive_skb_list routine to send skbs converted from
xdp_frames in cpu_map_kthread_run in order to improve i-cache usage.
The proposed patch has been tested running xdp_redirect_cpu bpf sample
available in the kernel tree that is used to redirect UDP frames from
ixgbe driver to a cpumap entry and then to the networking stack. UDP
frames are generated using pktgen. Packets are discarded by the UDP
layer.
$ xdp_redirect_cpu --cpu <cpu> --progname xdp_cpu_map0 --dev <eth>
bpf-next: ~2.35Mpps
bpf-next + cpumap skb-list: ~2.72Mpps
Rename drops counter in kmem_alloc_drops since now it reports just
kmem_cache_alloc_bulk failures
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/c729f83e5d7482d9329e0f165bdbe5adcefd1510.1619169700.git.lorenzo@kernel.org
|
|
Similarly as b02709587ea3 ("bpf: Fix propagation of 32-bit signed bounds
from 64-bit bounds."), we also need to fix the propagation of 32 bit
unsigned bounds from 64 bit counterparts. That is, really only set the
u32_{min,max}_value when /both/ {umin,umax}_value safely fit in 32 bit
space. For example, the register with a umin_value == 1 does /not/ imply
that u32_min_value is also equal to 1, since umax_value could be much
larger than 32 bit subregister can hold, and thus u32_min_value is in
the interval [0,1] instead.
Before fix, invalid tracking result of R2_w=inv1:
[...]
5: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0) R10=fp0
5: (35) if r2 >= 0x1 goto pc+1
[...] // goto path
7: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,umin_value=1) R10=fp0
7: (b6) if w2 <= 0x1 goto pc+1
[...] // goto path
9: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,smin_value=-9223372036854775807,smax_value=9223372032559808513,umin_value=1,umax_value=18446744069414584321,var_off=(0x1; 0xffffffff00000000),s32_min_value=1,s32_max_value=1,u32_max_value=1) R10=fp0
9: (bc) w2 = w2
10: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv1 R10=fp0
[...]
After fix, correct tracking result of R2_w=inv(id=0,umax_value=1,var_off=(0x0; 0x1)):
[...]
5: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0) R10=fp0
5: (35) if r2 >= 0x1 goto pc+1
[...] // goto path
7: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,umin_value=1) R10=fp0
7: (b6) if w2 <= 0x1 goto pc+1
[...] // goto path
9: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,smax_value=9223372032559808513,umax_value=18446744069414584321,var_off=(0x0; 0xffffffff00000001),s32_min_value=0,s32_max_value=1,u32_max_value=1) R10=fp0
9: (bc) w2 = w2
10: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,umax_value=1,var_off=(0x0; 0x1)) R10=fp0
[...]
Thus, same issue as in b02709587ea3 holds for unsigned subregister tracking.
Also, align __reg64_bound_u32() similarly to __reg64_bound_s32() as done in
b02709587ea3 to make them uniform again.
Fixes: 3f50f132d840 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Manfred Paul (@_manfp)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Currently we don't allow re-attaching of trampolines. Once
it's detached, it can't be re-attach even when the program
is still loaded.
Adding the possibility to re-attach the loaded tracing and
lsm programs.
Fixing missing unlock with proper cleanup goto jump reported
by Julia.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/bpf/20210414195147.1624932-2-jolsa@kernel.org
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-04-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 69 non-merge commits during the last 22 day(s) which contain
a total of 69 files changed, 3141 insertions(+), 866 deletions(-).
The main changes are:
1) Add BPF static linker support for extern resolution of global, from Andrii.
2) Refine retval for bpf_get_task_stack helper, from Dave.
3) Add a bpf_snprintf helper, from Florent.
4) A bunch of miscellaneous improvements from many developers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
reg->type is enforced by check_reg_type() and map should never be NULL
(it would already have been dereferenced anyway) so these checks are
unnecessary.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210422235543.4007694-3-revest@chromium.org
|
|
In check_bpf_snprintf_call(), a map_direct_value_addr() of the fmt map
should never fail because it has already been checked by
ARG_PTR_TO_CONST_STR. But if it ever fails, it's better to error out
with an explicit debug message rather than silently fail.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210422235543.4007694-2-revest@chromium.org
|
|
Verifier can constrain the min/max bounds of bpf_get_task_stack's return
value more tightly than the default tnum_unknown. Like bpf_get_stack,
return value is num bytes written into a caller-supplied buf, or error,
so do_refine_retval_range will work.
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210416204704.2816874-2-davemarchevsky@fb.com
|
|
The implementation takes inspiration from the existing bpf_trace_printk
helper but there are a few differences:
To allow for a large number of format-specifiers, parameters are
provided in an array, like in bpf_seq_printf.
Because the output string takes two arguments and the array of
parameters also takes two arguments, the format string needs to fit in
one argument. Thankfully, ARG_PTR_TO_CONST_STR is guaranteed to point to
a zero-terminated read-only map so we don't need a format string length
arg.
Because the format-string is known at verification time, we also do
a first pass of format string validation in the verifier logic. This
makes debugging easier.
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210419155243.1632274-4-revest@chromium.org
|
|
This type provides the guarantee that an argument is going to be a const
pointer to somewhere in a read-only map value. It also checks that this
pointer is followed by a zero character before the end of the map value.
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210419155243.1632274-3-revest@chromium.org
|
|
Two helpers (trace_printk and seq_printf) have very similar
implementations of format string parsing and a third one is coming
(snprintf). To avoid code duplication and make the code easier to
maintain, this moves the operations associated with format string
parsing (validation and argument sanitization) into one generic
function.
The implementation of the two existing helpers already drifted quite a
bit so unifying them entailed a lot of changes:
- bpf_trace_printk always expected fmt[fmt_size] to be the terminating
NULL character, this is no longer true, the first 0 is terminating.
- bpf_trace_printk now supports %% (which produces the percentage char).
- bpf_trace_printk now skips width formating fields.
- bpf_trace_printk now supports the X modifier (capital hexadecimal).
- bpf_trace_printk now supports %pK, %px, %pB, %pi4, %pI4, %pi6 and %pI6
- argument casting on 32 bit has been simplified into one macro and
using an enum instead of obscure int increments.
- bpf_seq_printf now uses bpf_trace_copy_string instead of
strncpy_from_kernel_nofault and handles the %pks %pus specifiers.
- bpf_seq_printf now prints longs correctly on 32 bit architectures.
- both were changed to use a global per-cpu tmp buffer instead of one
stack buffer for trace_printk and 6 small buffers for seq_printf.
- to avoid per-cpu buffer usage conflict, these helpers disable
preemption while the per-cpu buffer is in use.
- both helpers now support the %ps and %pS specifiers to print symbols.
The implementation is also moved from bpf_trace.c to helpers.c because
the upcoming bpf_snprintf helper will be made available to all BPF
programs and will need it.
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210419155243.1632274-2-revest@chromium.org
|
|
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This work tightens the offset mask we use for unprivileged pointer arithmetic
in order to mitigate a corner case reported by Piotr and Benedict where in
the speculative domain it is possible to advance, for example, the map value
pointer by up to value_size-1 out-of-bounds in order to leak kernel memory
via side-channel to user space.
Before this change, the computed ptr_limit for retrieve_ptr_limit() helper
represents largest valid distance when moving pointer to the right or left
which is then fed as aux->alu_limit to generate masking instructions against
the offset register. After the change, the derived aux->alu_limit represents
the largest potential value of the offset register which we mask against which
is just a narrower subset of the former limit.
For minimal complexity, we call sanitize_ptr_alu() from 2 observation points
in adjust_ptr_min_max_vals(), that is, before and after the simulated alu
operation. In the first step, we retieve the alu_state and alu_limit before
the operation as well as we branch-off a verifier path and push it to the
verification stack as we did before which checks the dst_reg under truncation,
in other words, when the speculative domain would attempt to move the pointer
out-of-bounds.
In the second step, we retrieve the new alu_limit and calculate the absolute
distance between both. Moreover, we commit the alu_state and final alu_limit
via update_alu_sanitation_state() to the env's instruction aux data, and bail
out from there if there is a mismatch due to coming from different verification
paths with different states.
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Reported-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Benedict Schlueter <benedict.schlueter@rub.de>
|
|
Add a small sanitize_needed() helper function and move sanitize_val_alu()
out of the main opcode switch. In upcoming work, we'll move sanitize_ptr_alu()
as well out of its opcode switch so this helps to streamline both.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Move the bounds check in adjust_ptr_min_max_vals() into a small helper named
sanitize_check_bounds() in order to simplify the former a bit.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Consolidate all error handling and provide more user-friendly error messages
from sanitize_ptr_alu() and sanitize_val_alu().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Small refactor with no semantic changes in order to consolidate the max
ptr_limit boundary check.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
The mixed signed bounds check really belongs into retrieve_ptr_limit()
instead of outside of it in adjust_ptr_min_max_vals(). The reason is
that this check is not tied to PTR_TO_MAP_VALUE only, but to all pointer
types that we handle in retrieve_ptr_limit() and given errors from the latter
propagate back to adjust_ptr_min_max_vals() and lead to rejection of the
program, it's a better place to reside to avoid anything slipping through
for future types. The reason why we must reject such off_reg is that we
otherwise would not be able to derive a mask, see details in 9d7eceede769
("bpf: restrict unknown scalars of mixed signed bounds for unprivileged").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Small refactor to drag off_reg into sanitize_ptr_alu(), so we later on can
use off_reg for generalizing some of the checks for all pointer types.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
We forbid adding unknown scalars with mixed signed bounds due to the
spectre v1 masking mitigation. Hence this also needs bypass_spec_v1
flag instead of allow_ptr_leaks.
Fixes: 2c78ee898d8f ("bpf: Implement CAP_BPF")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
There is currently no way to discover the target of a tracing program
attachment after the fact. Add this information to bpf_link_info and return
it when querying the bpf_link fd.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210413091607.58945-1-toke@redhat.com
|
|
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bpf_preload_lock is already defined with DEFINE_MUTEX(). There is no
need to initialize it again. Remove the extraneous initialization.
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210405194904.GA148013@LEGION
|
|
'stack' parameter is not used in ___bpf_prog_run() after f696b8f471ec
("bpf: split bpf core interpreter"), the base address have been set to
FP reg. So consequently remove it.
Signed-off-by: He Fengqing <hefengqing@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210331075135.3850782-1-hefengqing@huawei.com
|
|
As for bpf_link, refuse creating a non-O_RDWR fd. Since program fds
currently don't allow modifications this is a precaution, not a
straight up bug fix.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210326160501.46234-2-lmb@cloudflare.com
|
