summaryrefslogtreecommitdiff
path: root/net/ipv6
AgeCommit message (Collapse)AuthorFilesLines
2020-04-13ipv6: don't auto-add link-local address to lag portsJarod Wilson1-0/+4
[ Upstream commit 744fdc8233f6aa9582ce08a51ca06e59796a3196 ] Bonding slave and team port devices should not have link-local addresses automatically added to them, as it can interfere with openvswitch being able to properly add tc ingress. Basic reproducer, courtesy of Marcelo: $ ip link add name bond0 type bond $ ip link set dev ens2f0np0 master bond0 $ ip link set dev ens2f1np2 master bond0 $ ip link set dev bond0 up $ ip a s 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master bond0 state UP group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff 5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc mq master bond0 state DOWN group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff 11: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff inet6 fe80::20f:53ff:fe2f:ea40/64 scope link valid_lft forever preferred_lft forever (above trimmed to relevant entries, obviously) $ sysctl net.ipv6.conf.ens2f0np0.addr_gen_mode=0 net.ipv6.conf.ens2f0np0.addr_gen_mode = 0 $ sysctl net.ipv6.conf.ens2f1np2.addr_gen_mode=0 net.ipv6.conf.ens2f1np2.addr_gen_mode = 0 $ ip a l ens2f0np0 2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master bond0 state UP group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative valid_lft forever preferred_lft forever $ ip a l ens2f1np2 5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc mq master bond0 state DOWN group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative valid_lft forever preferred_lft forever Looks like addrconf_sysctl_addr_gen_mode() bypasses the original "is this a slave interface?" check added by commit c2edacf80e15, and results in an address getting added, while w/the proposed patch added, no address gets added. This simply adds the same gating check to another code path, and thus should prevent the same devices from erroneously obtaining an ipv6 link-local address. Fixes: d35a00b8e33d ("net/ipv6: allow sysctl to change link-local address generation mode") Reported-by: Moshe Levi <moshele@mellanox.com> CC: Stephen Hemminger <stephen@networkplumber.org> CC: Marcelo Ricardo Leitner <mleitner@redhat.com> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-04-01vti6: Fix memory leak of skb if input policy check failsTorsten Hilbrich1-1/+1
commit 2a9de3af21aa8c31cd68b0b39330d69f8c1e59df upstream. The vti6_rcv function performs some tests on the retrieved tunnel including checking the IP protocol, the XFRM input policy, the source and destination address. In all but one places the skb is released in the error case. When the input policy check fails the network packet is leaked. Using the same goto-label discard in this case to fix this problem. Fixes: ed1efb2aefbb ("ipv6: Add support for IPsec virtual tunnel interfaces") Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com> Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-04-01vti[6]: fix packet tx through bpf_redirect() in XinY casesNicolas Dichtel1-7/+25
commit f1ed10264ed6b66b9cd5e8461cffce69be482356 upstream. I forgot the 4in6/6in4 cases in my previous patch. Let's fix them. Fixes: 95224166a903 ("vti[6]: fix packet tx through bpf_redirect()") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-18ipv6: restrict IPV6_ADDRFORM operationEric Dumazet1-2/+8
commit b6f6118901d1e867ac9177bbff3b00b185bd4fdc upstream. IPV6_ADDRFORM is able to transform IPv6 socket to IPv4 one. While this operation sounds illogical, we have to support it. One of the things it does for TCP socket is to switch sk->sk_prot to tcp_prot. We now have other layers playing with sk->sk_prot, so we should make sure to not interfere with them. This patch makes sure sk_prot is the default pointer for TCP IPv6 socket. syzbot reported : BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD a0113067 P4D a0113067 PUD a8771067 PMD 0 Oops: 0010 [#1] PREEMPT SMP KASAN CPU: 0 PID: 10686 Comm: syz-executor.0 Not tainted 5.6.0-rc2-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:0x0 Code: Bad RIP value. RSP: 0018:ffffc9000281fce0 EFLAGS: 00010246 RAX: 1ffffffff15f48ac RBX: ffffffff8afa4560 RCX: dffffc0000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8880a69a8f40 RBP: ffffc9000281fd10 R08: ffffffff86ed9b0c R09: ffffed1014d351f5 R10: ffffed1014d351f5 R11: 0000000000000000 R12: ffff8880920d3098 R13: 1ffff1101241a613 R14: ffff8880a69a8f40 R15: 0000000000000000 FS: 00007f2ae75db700(0000) GS:ffff8880aea00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 00000000a3b85000 CR4: 00000000001406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: inet_release+0x165/0x1c0 net/ipv4/af_inet.c:427 __sock_release net/socket.c:605 [inline] sock_close+0xe1/0x260 net/socket.c:1283 __fput+0x2e4/0x740 fs/file_table.c:280 ____fput+0x15/0x20 fs/file_table.c:313 task_work_run+0x176/0x1b0 kernel/task_work.c:113 tracehook_notify_resume include/linux/tracehook.h:188 [inline] exit_to_usermode_loop arch/x86/entry/common.c:164 [inline] prepare_exit_to_usermode+0x480/0x5b0 arch/x86/entry/common.c:195 syscall_return_slowpath+0x113/0x4a0 arch/x86/entry/common.c:278 do_syscall_64+0x11f/0x1c0 arch/x86/entry/common.c:304 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x45c429 Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f2ae75dac78 EFLAGS: 00000246 ORIG_RAX: 0000000000000036 RAX: 0000000000000000 RBX: 00007f2ae75db6d4 RCX: 000000000045c429 RDX: 0000000000000001 RSI: 000000000000011a RDI: 0000000000000004 RBP: 000000000076bf20 R08: 0000000000000038 R09: 0000000000000000 R10: 0000000020000180 R11: 0000000000000246 R12: 00000000ffffffff R13: 0000000000000a9d R14: 00000000004ccfb4 R15: 000000000076bf2c Modules linked in: CR2: 0000000000000000 ---[ end trace 82567b5207e87bae ]--- RIP: 0010:0x0 Code: Bad RIP value. RSP: 0018:ffffc9000281fce0 EFLAGS: 00010246 RAX: 1ffffffff15f48ac RBX: ffffffff8afa4560 RCX: dffffc0000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8880a69a8f40 RBP: ffffc9000281fd10 R08: ffffffff86ed9b0c R09: ffffed1014d351f5 R10: ffffed1014d351f5 R11: 0000000000000000 R12: ffff8880920d3098 R13: 1ffff1101241a613 R14: ffff8880a69a8f40 R15: 0000000000000000 FS: 00007f2ae75db700(0000) GS:ffff8880aea00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 00000000a3b85000 CR4: 00000000001406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot+1938db17e275e85dc328@syzkaller.appspotmail.com Cc: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-18net/ipv6: remove the old peer route if change it to a new oneHangbin Liu1-4/+17
[ Upstream commit d0098e4c6b83e502cc1cd96d67ca86bc79a6c559 ] When we modify the peer route and changed it to a new one, we should remove the old route first. Before the fix: + ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 256 pref medium 2001:db8::2 proto kernel metric 256 pref medium + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 256 pref medium 2001:db8::2 proto kernel metric 256 pref medium After the fix: + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 256 pref medium 2001:db8::3 proto kernel metric 256 pref medium This patch depend on the previous patch "net/ipv6: need update peer route when modify metric" to update new peer route after delete old one. Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-18net/ipv6: need update peer route when modify metricHangbin Liu1-4/+16
[ Upstream commit 617940123e0140521f3080d2befc2bf55bcda094 ] When we modify the route metric, the peer address's route need also be updated. Before the fix: + ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 metric 60 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 60 pref medium 2001:db8::2 proto kernel metric 60 pref medium + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 61 pref medium 2001:db8::2 proto kernel metric 60 pref medium After the fix: + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 61 pref medium 2001:db8::2 proto kernel metric 61 pref medium Fixes: 8308f3ff1753 ("net/ipv6: Add support for specifying metric of connected routes") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-18net/ipv6: use configured metric when add peer routeHangbin Liu1-3/+3
[ Upstream commit 07758eb9ff52794fba15d03aa88d92dbd1b7d125 ] When we add peer address with metric configured, IPv4 could set the dest metric correctly, but IPv6 do not. e.g. ]# ip addr add 192.0.2.1 peer 192.0.2.2/32 dev eth1 metric 20 ]# ip route show dev eth1 192.0.2.2 proto kernel scope link src 192.0.2.1 metric 20 ]# ip addr add 2001:db8::1 peer 2001:db8::2/128 dev eth1 metric 20 ]# ip -6 route show dev eth1 2001:db8::1 proto kernel metric 20 pref medium 2001:db8::2 proto kernel metric 256 pref medium Fix this by using configured metric instead of default one. Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 8308f3ff1753 ("net/ipv6: Add support for specifying metric of connected routes") Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-18ipv6/addrconf: call ipv6_mc_up() for non-Ethernet interfaceHangbin Liu1-0/+4
[ Upstream commit 60380488e4e0b95e9e82aa68aa9705baa86de84c ] Rafał found an issue that for non-Ethernet interface, if we down and up frequently, the memory will be consumed slowly. The reason is we add allnodes/allrouters addressed in multicast list in ipv6_add_dev(). When link down, we call ipv6_mc_down(), store all multicast addresses via mld_add_delrec(). But when link up, we don't call ipv6_mc_up() for non-Ethernet interface to remove the addresses. This makes idev->mc_tomb getting bigger and bigger. The call stack looks like: addrconf_notify(NETDEV_REGISTER) ipv6_add_dev ipv6_dev_mc_inc(ff01::1) ipv6_dev_mc_inc(ff02::1) ipv6_dev_mc_inc(ff02::2) addrconf_notify(NETDEV_UP) addrconf_dev_config /* Alas, we support only Ethernet autoconfiguration. */ return; addrconf_notify(NETDEV_DOWN) addrconf_ifdown ipv6_mc_down igmp6_group_dropped(ff02::2) mld_add_delrec(ff02::2) igmp6_group_dropped(ff02::1) igmp6_group_dropped(ff01::1) After investigating, I can't found a rule to disable multicast on non-Ethernet interface. In RFC2460, the link could be Ethernet, PPP, ATM, tunnels, etc. In IPv4, it doesn't check the dev type when calls ip_mc_up() in inetdev_event(). Even for IPv6, we don't check the dev type and call ipv6_add_dev(), ipv6_dev_mc_inc() after register device. So I think it's OK to fix this memory consumer by calling ipv6_mc_up() for non-Ethernet interface. v2: Also check IFF_MULTICAST flag to make sure the interface supports multicast Reported-by: Rafał Miłecki <zajec5@gmail.com> Tested-by: Rafał Miłecki <zajec5@gmail.com> Fixes: 74235a25c673 ("[IPV6] addrconf: Fix IPv6 on tuntap tunnels") Fixes: 1666d49e1d41 ("mld: do not remove mld souce list info when set link down") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-05ipv6: Fix nlmsg_flags when splitting a multipath routeBenjamin Poirier1-0/+1
[ Upstream commit afecdb376bd81d7e16578f0cfe82a1aec7ae18f3 ] When splitting an RTA_MULTIPATH request into multiple routes and adding the second and later components, we must not simply remove NLM_F_REPLACE but instead replace it by NLM_F_CREATE. Otherwise, it may look like the netlink message was malformed. For example, ip route add 2001:db8::1/128 dev dummy0 ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 \ nexthop via fe80::30:2 dev dummy0 results in the following warnings: [ 1035.057019] IPv6: RTM_NEWROUTE with no NLM_F_CREATE or NLM_F_REPLACE [ 1035.057517] IPv6: NLM_F_CREATE should be set when creating new route This patch makes the nlmsg sequence look equivalent for __ip6_ins_rt() to what it would get if the multipath route had been added in multiple netlink operations: ip route add 2001:db8::1/128 dev dummy0 ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 ip route append 2001:db8::1/128 nexthop via fe80::30:2 dev dummy0 Fixes: 27596472473a ("ipv6: fix ECMP route replacement") Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-05ipv6: Fix route replacement with dev-only routeBenjamin Poirier1-3/+4
[ Upstream commit e404b8c7cfb31654c9024d497cec58a501501692 ] After commit 27596472473a ("ipv6: fix ECMP route replacement") it is no longer possible to replace an ECMP-able route by a non ECMP-able route. For example, ip route add 2001:db8::1/128 via fe80::1 dev dummy0 ip route replace 2001:db8::1/128 dev dummy0 does not work as expected. Tweak the replacement logic so that point 3 in the log of the above commit becomes: 3. If the new route is not ECMP-able, and no matching non-ECMP-able route exists, replace matching ECMP-able route (if any) or add the new route. We can now summarize the entire replace semantics to: When doing a replace, prefer replacing a matching route of the same "ECMP-able-ness" as the replace argument. If there is no such candidate, fallback to the first route found. Fixes: 27596472473a ("ipv6: fix ECMP route replacement") Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-11ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()Eric Dumazet1-0/+3
[ Upstream commit db3fa271022dacb9f741b96ea4714461a8911bb9 ] __in6_dev_get(dev) called from inet6_set_link_af() can return NULL. The needed check has been recently removed, let's add it back. While do_setlink() does call validate_linkmsg() : ... err = validate_linkmsg(dev, tb); /* OK at this point */ ... It is possible that the following call happening before the ->set_link_af() removes IPv6 if MTU is less than 1280 : if (tb[IFLA_MTU]) { err = dev_set_mtu_ext(dev, nla_get_u32(tb[IFLA_MTU]), extack); if (err < 0) goto errout; status |= DO_SETLINK_MODIFIED; } ... if (tb[IFLA_AF_SPEC]) { ... err = af_ops->set_link_af(dev, af); ->inet6_set_link_af() // CRASH because idev is NULL Please note that IPv4 is immune to the bug since inet_set_link_af() does : struct in_device *in_dev = __in_dev_get_rcu(dev); if (!in_dev) return -EAFNOSUPPORT; This problem has been mentioned in commit cf7afbfeb8ce ("rtnl: make link af-specific updates atomic") changelog : This method is not fail proof, while it is currently sufficient to make set_link_af() inerrable and thus 100% atomic, the validation function method will not be able to detect all error scenarios in the future, there will likely always be errors depending on states which are f.e. not protected by rtnl_mutex and thus may change between validation and setting. IPv6: ADDRCONF(NETDEV_CHANGE): lo: link becomes ready general protection fault, probably for non-canonical address 0xdffffc0000000056: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x00000000000002b0-0x00000000000002b7] CPU: 0 PID: 9698 Comm: syz-executor712 Not tainted 5.5.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:inet6_set_link_af+0x66e/0xae0 net/ipv6/addrconf.c:5733 Code: 38 d0 7f 08 84 c0 0f 85 20 03 00 00 48 8d bb b0 02 00 00 45 0f b6 64 24 04 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 08 3c 03 0f 8e 1a 03 00 00 44 89 a3 b0 02 00 RSP: 0018:ffffc90005b06d40 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff86df39a6 RDX: 0000000000000056 RSI: ffffffff86df3e74 RDI: 00000000000002b0 RBP: ffffc90005b06e70 R08: ffff8880a2ac0380 R09: ffffc90005b06db0 R10: fffff52000b60dbe R11: ffffc90005b06df7 R12: 0000000000000000 R13: 0000000000000000 R14: ffff8880a1fcc424 R15: dffffc0000000000 FS: 0000000000c46880(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055f0494ca0d0 CR3: 000000009e4ac000 CR4: 00000000001406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: do_setlink+0x2a9f/0x3720 net/core/rtnetlink.c:2754 rtnl_group_changelink net/core/rtnetlink.c:3103 [inline] __rtnl_newlink+0xdd1/0x1790 net/core/rtnetlink.c:3257 rtnl_newlink+0x69/0xa0 net/core/rtnetlink.c:3377 rtnetlink_rcv_msg+0x45e/0xaf0 net/core/rtnetlink.c:5438 netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5456 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0x59e/0x7e0 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x91c/0xea0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:652 [inline] sock_sendmsg+0xd7/0x130 net/socket.c:672 ____sys_sendmsg+0x753/0x880 net/socket.c:2343 ___sys_sendmsg+0x100/0x170 net/socket.c:2397 __sys_sendmsg+0x105/0x1d0 net/socket.c:2430 __do_sys_sendmsg net/socket.c:2439 [inline] __se_sys_sendmsg net/socket.c:2437 [inline] __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2437 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4402e9 Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fffd62fbcf8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 00000000004402e9 RDX: 0000000000000000 RSI: 0000000020000080 RDI: 0000000000000003 RBP: 00000000006ca018 R08: 0000000000000008 R09: 00000000004002c8 R10: 0000000000000005 R11: 0000000000000246 R12: 0000000000401b70 R13: 0000000000401c00 R14: 0000000000000000 R15: 0000000000000000 Modules linked in: ---[ end trace cfa7664b8fdcdff3 ]--- RIP: 0010:inet6_set_link_af+0x66e/0xae0 net/ipv6/addrconf.c:5733 Code: 38 d0 7f 08 84 c0 0f 85 20 03 00 00 48 8d bb b0 02 00 00 45 0f b6 64 24 04 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 08 3c 03 0f 8e 1a 03 00 00 44 89 a3 b0 02 00 RSP: 0018:ffffc90005b06d40 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff86df39a6 RDX: 0000000000000056 RSI: ffffffff86df3e74 RDI: 00000000000002b0 RBP: ffffc90005b06e70 R08: ffff8880a2ac0380 R09: ffffc90005b06db0 R10: fffff52000b60dbe R11: ffffc90005b06df7 R12: 0000000000000000 R13: 0000000000000000 R14: ffff8880a1fcc424 R15: dffffc0000000000 FS: 0000000000c46880(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000004 CR3: 000000009e4ac000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Fixes: 7dc2bccab0ee ("Validate required parameters in inet6_validate_link_af") Signed-off-by: Eric Dumazet <edumazet@google.com> Bisected-and-reported-by: syzbot <syzkaller@googlegroups.com> Cc: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-06vti[6]: fix packet tx through bpf_redirect()Nicolas Dichtel1-2/+11
[ Upstream commit 95224166a9032ff5d08fca633d37113078ce7d01 ] With an ebpf program that redirects packets through a vti[6] interface, the packets are dropped because no dst is attached. This could also be reproduced with an AF_PACKET socket, with the following python script (vti1 is an ip_vti interface): import socket send_s = socket.socket(socket.AF_PACKET, socket.SOCK_RAW, 0) # scapy # p = IP(src='10.100.0.2', dst='10.200.0.1')/ICMP(type='echo-request') # raw(p) req = b'E\x00\x00\x1c\x00\x01\x00\x00@\x01e\xb2\nd\x00\x02\n\xc8\x00\x01\x08\x00\xf7\xff\x00\x00\x00\x00' send_s.sendto(req, ('vti1', 0x800, 0, 0)) Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-01-29xfrm: support output_mark for offload ESP packetsUlrich Weber1-0/+2
commit 4e4362d2bf2a49ff44dbbc9585207977ca3d71d0 upstream. Commit 9b42c1f179a6 ("xfrm: Extend the output_mark") added output_mark support but missed ESP offload support. xfrm_smark_get() is not called within xfrm_input() for packets coming from esp4_gro_receive() or esp6_gro_receive(). Therefore call xfrm_smark_get() directly within these functions. Fixes: 9b42c1f179a6 ("xfrm: Extend the output_mark to support input direction and masking.") Signed-off-by: Ulrich Weber <ulrich.weber@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-29net, ip6_tunnel: fix namespaces moveWilliam Dauchy1-3/+1
[ Upstream commit 5311a69aaca30fa849c3cc46fb25f75727fb72d0 ] in the same manner as commit d0f418516022 ("net, ip_tunnel: fix namespaces move"), fix namespace moving as it was broken since commit 8d79266bc48c ("ip6_tunnel: add collect_md mode to IPv6 tunnel"), but for ipv6 this time; there is no reason to keep it for ip6_tunnel. Fixes: 8d79266bc48c ("ip6_tunnel: add collect_md mode to IPv6 tunnel") Signed-off-by: William Dauchy <w.dauchy@criteo.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-29net: ip6_gre: fix moving ip6gre between namespacesNiko Kortstrom1-3/+0
[ Upstream commit 690afc165bb314354667f67157c1a1aea7dc797a ] Support for moving IPv4 GRE tunnels between namespaces was added in commit b57708add314 ("gre: add x-netns support"). The respective change for IPv6 tunnels, commit 22f08069e8b4 ("ip6gre: add x-netns support") did not drop NETIF_F_NETNS_LOCAL flag so moving them from one netns to another is still denied in IPv6 case. Drop NETIF_F_NETNS_LOCAL flag from ip6gre tunnels to allow moving ip6gre tunnel endpoints between network namespaces. Signed-off-by: Niko Kortstrom <niko.kortstrom@nokia.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-29ipv6: sr: remove SKB_GSO_IPXIP6 on End.D* actionsYuki Taguchi1-1/+3
[ Upstream commit 62ebaeaedee7591c257543d040677a60e35c7aec ] After LRO/GRO is applied, SRv6 encapsulated packets have SKB_GSO_IPXIP6 feature flag, and this flag must be removed right after decapulation procedure. Currently, SKB_GSO_IPXIP6 flag is not removed on End.D* actions, which creates inconsistent packet state, that is, a normal TCP/IP packets have the SKB_GSO_IPXIP6 flag. This behavior can cause unexpected fallback to GSO on routing to netdevices that do not support SKB_GSO_IPXIP6. For example, on inter-VRF forwarding, decapsulated packets separated into small packets by GSO because VRF devices do not support TSO for packets with SKB_GSO_IPXIP6 flag, and this degrades forwarding performance. This patch removes encapsulation related GSO flags from the skb right after the End.D* action is applied. Fixes: d7a669dd2f8b ("ipv6: sr: add helper functions for seg6local") Signed-off-by: Yuki Taguchi <tagyounit@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04ipv6/addrconf: only check invalid header values when NETLINK_F_STRICT_CHK is setHangbin Liu1-4/+4
[ Upstream commit 2beb6d2901a3f73106485d560c49981144aeacb1 ] In commit 4b1373de73a3 ("net: ipv6: addr: perform strict checks also for doit handlers") we add strict check for inet6_rtm_getaddr(). But we did the invalid header values check before checking if NETLINK_F_STRICT_CHK is set. This may break backwards compatibility if user already set the ifm->ifa_prefixlen, ifm->ifa_flags, ifm->ifa_scope in their netlink code. I didn't move the nlmsg_len check because I thought it's a valid check. Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 4b1373de73a3 ("net: ipv6: addr: perform strict checks also for doit handlers") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04sit: do not confirm neighbor when do pmtu updateHangbin Liu1-1/+1
[ Upstream commit 4d42df46d6372ece4cb4279870b46c2ea7304a47 ] When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end, we should not call dst_confirm_neigh() as there is no two-way communication. v5: No change. v4: No change. v3: Do not remove dst_confirm_neigh, but add a new bool parameter in dst_ops.update_pmtu to control whether we should do neighbor confirm. Also split the big patch to small ones for each area. v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu. Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04vti: do not confirm neighbor when do pmtu updateHangbin Liu1-1/+1
[ Upstream commit 8247a79efa2f28b44329f363272550c1738377de ] When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end, we should not call dst_confirm_neigh() as there is no two-way communication. Although vti and vti6 are immune to this problem because they are IFF_NOARP interfaces, as Guillaume pointed. There is still no sense to confirm neighbour here. v5: Update commit description. v4: No change. v3: Do not remove dst_confirm_neigh, but add a new bool parameter in dst_ops.update_pmtu to control whether we should do neighbor confirm. Also split the big patch to small ones for each area. v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu. Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04tunnel: do not confirm neighbor when do pmtu updateHangbin Liu1-2/+2
[ Upstream commit 7a1592bcb15d71400a98632727791d1e68ea0ee8 ] When do tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end, we should not call dst_confirm_neigh() as there is no two-way communication. v5: No Change. v4: Update commit description v3: Do not remove dst_confirm_neigh, but add a new bool parameter in dst_ops.update_pmtu to control whether we should do neighbor confirm. Also split the big patch to small ones for each area. v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu. Fixes: 0dec879f636f ("net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP") Reviewed-by: Guillaume Nault <gnault@redhat.com> Tested-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04ip6_gre: do not confirm neighbor when do pmtu updateHangbin Liu1-1/+1
[ Upstream commit 675d76ad0ad5bf41c9a129772ef0aba8f57ea9a7 ] When we do ipv6 gre pmtu update, we will also do neigh confirm currently. This will cause the neigh cache be refreshed and set to REACHABLE before xmit. But if the remote mac address changed, e.g. device is deleted and recreated, we will not able to notice this and still use the old mac address as the neigh cache is REACHABLE. Fix this by disable neigh confirm when do pmtu update v5: No change. v4: No change. v3: Do not remove dst_confirm_neigh, but add a new bool parameter in dst_ops.update_pmtu to control whether we should do neighbor confirm. Also split the big patch to small ones for each area. v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu. Reported-by: Jianlin Shi <jishi@redhat.com> Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04net: add bool confirm_neigh parameter for dst_ops.update_pmtuHangbin Liu4-11/+20
[ Upstream commit bd085ef678b2cc8c38c105673dfe8ff8f5ec0c57 ] The MTU update code is supposed to be invoked in response to real networking events that update the PMTU. In IPv6 PMTU update function __ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor confirmed time. But for tunnel code, it will call pmtu before xmit, like: - tnl_update_pmtu() - skb_dst_update_pmtu() - ip6_rt_update_pmtu() - __ip6_rt_update_pmtu() - dst_confirm_neigh() If the tunnel remote dst mac address changed and we still do the neigh confirm, we will not be able to update neigh cache and ping6 remote will failed. So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we should not be invoking dst_confirm_neigh() as we have no evidence of successful two-way communication at this point. On the other hand it is also important to keep the neigh reachability fresh for TCP flows, so we cannot remove this dst_confirm_neigh() call. To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu to choose whether we should do neigh update or not. I will add the parameter in this patch and set all the callers to true to comply with the previous way, and fix the tunnel code one by one on later patches. v5: No change. v4: No change. v3: Do not remove dst_confirm_neigh, but add a new bool parameter in dst_ops.update_pmtu to control whether we should do neighbor confirm. Also split the big patch to small ones for each area. v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu. Suggested-by: David Miller <davem@davemloft.net> Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-18net: ipv6_stub: use ip6_dst_lookup_flow instead of ip6_dst_lookupSabrina Dubroca2-6/+7
[ Upstream commit 6c8991f41546c3c472503dff1ea9daaddf9331c2 ] ipv6_stub uses the ip6_dst_lookup function to allow other modules to perform IPv6 lookups. However, this function skips the XFRM layer entirely. All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the ip_route_output_key and ip_route_output helpers) for their IPv4 lookups, which calls xfrm_lookup_route(). This patch fixes this inconsistent behavior by switching the stub to ip6_dst_lookup_flow, which also calls xfrm_lookup_route(). This requires some changes in all the callers, as these two functions take different arguments and have different return types. Fixes: 5f81bd2e5d80 ("ipv6: export a stub for IPv6 symbols used by vxlan") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-18net: ipv6: add net argument to ip6_dst_lookup_flowSabrina Dubroca7-12/+12
[ Upstream commit c4e85f73afb6384123e5ef1bba3315b2e3ad031e ] This will be used in the conversion of ipv6_stub to ip6_dst_lookup_flow, as some modules currently pass a net argument without a socket to ip6_dst_lookup. This is equivalent to commit 343d60aada5a ("ipv6: change ipv6_stub_impl.ipv6_dst_lookup to take net argument"). Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-22net-ipv6: IPV6_TRANSPARENT - check NET_RAW prior to NET_ADMINMaciej Żenczykowski1-2/+2
NET_RAW is less dangerous, so more likely to be available to a process, so check it first to prevent some spurious logging. This matches IP_TRANSPARENT which checks NET_RAW first. Signed-off-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20ipv6/route: return if there is no fib_nh_gw_familyHangbin Liu1-1/+1
Previously we will return directly if (!rt || !rt->fib6_nh.fib_nh_gw_family) in function rt6_probe(), but after commit cc3a86c802f0 ("ipv6: Change rt6_probe to take a fib6_nh"), the logic changed to return if there is fib_nh_gw_family. Fixes: cc3a86c802f0 ("ipv6: Change rt6_probe to take a fib6_nh") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-16seg6: fix skb transport_header after decap_and_validate()Andrea Mayer1-0/+6
in the receive path (more precisely in ip6_rcv_core()) the skb->transport_header is set to skb->network_header + sizeof(*hdr). As a consequence, after routing operations, destination input expects to find skb->transport_header correctly set to the next protocol (or extension header) that follows the network protocol. However, decap behaviors (DX*, DT*) remove the outer IPv6 and SRH extension and do not set again the skb->transport_header pointer correctly. For this reason, the patch sets the skb->transport_header to the skb->network_header + sizeof(hdr) in each DX* and DT* behavior. Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-16seg6: fix srh pointer in get_srh()Andrea Mayer1-0/+5
pskb_may_pull may change pointers in header. For this reason, it is mandatory to reload any pointer that points into skb header. Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-08ipv6: fixes rt6_probe() and fib6_nh->last_probe initEric Dumazet1-3/+10
While looking at a syzbot KCSAN report [1], I found multiple issues in this code : 1) fib6_nh->last_probe has an initial value of 0. While probably okay on 64bit kernels, this causes an issue on 32bit kernels since the time_after(jiffies, 0 + interval) might be false ~24 days after boot (for HZ=1000) 2) The data-race found by KCSAN I could use READ_ONCE() and WRITE_ONCE(), but we also can take the opportunity of not piling-up too many rt6_probe_deferred() works by using instead cmpxchg() so that only one cpu wins the race. [1] BUG: KCSAN: data-race in find_match / find_match write to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 1: rt6_probe net/ipv6/route.c:663 [inline] find_match net/ipv6/route.c:757 [inline] find_match+0x5bd/0x790 net/ipv6/route.c:733 __find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831 find_rr_leaf net/ipv6/route.c:852 [inline] rt6_select net/ipv6/route.c:896 [inline] fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164 ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200 ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452 fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117 ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484 ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497 ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049 ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150 inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106 inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121 __tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169 tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline] tcp_xmit_probe_skb+0x19b/0x1d0 net/ipv4/tcp_output.c:3735 read to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 0: rt6_probe net/ipv6/route.c:657 [inline] find_match net/ipv6/route.c:757 [inline] find_match+0x521/0x790 net/ipv6/route.c:733 __find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831 find_rr_leaf net/ipv6/route.c:852 [inline] rt6_select net/ipv6/route.c:896 [inline] fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164 ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200 ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452 fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117 ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484 ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497 ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049 ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150 inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106 inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121 __tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 18894 Comm: udevd Not tainted 5.4.0-rc3+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Fixes: cc3a86c802f0 ("ipv6: Change rt6_probe to take a fib6_nh") Fixes: f547fac624be ("ipv6: rate-limit probes for neighbourless routes") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-30net: annotate accesses to sk->sk_incoming_cpuEric Dumazet2-2/+2
This socket field can be read and written by concurrent cpus. Use READ_ONCE() and WRITE_ONCE() annotations to document this, and avoid some compiler 'optimizations'. KCSAN reported : BUG: KCSAN: data-race in tcp_v4_rcv / tcp_v4_rcv write to 0xffff88812220763c of 4 bytes by interrupt on cpu 0: sk_incoming_cpu_update include/net/sock.h:953 [inline] tcp_v4_rcv+0x1b3c/0x1bb0 net/ipv4/tcp_ipv4.c:1934 ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204 ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252 dst_input include/net/dst.h:442 [inline] ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523 __netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010 __netif_receive_skb+0x37/0xf0 net/core/dev.c:5124 process_backlog+0x1d3/0x420 net/core/dev.c:5955 napi_poll net/core/dev.c:6392 [inline] net_rx_action+0x3ae/0xa90 net/core/dev.c:6460 __do_softirq+0x115/0x33f kernel/softirq.c:292 do_softirq_own_stack+0x2a/0x40 arch/x86/entry/entry_64.S:1082 do_softirq.part.0+0x6b/0x80 kernel/softirq.c:337 do_softirq kernel/softirq.c:329 [inline] __local_bh_enable_ip+0x76/0x80 kernel/softirq.c:189 read to 0xffff88812220763c of 4 bytes by interrupt on cpu 1: sk_incoming_cpu_update include/net/sock.h:952 [inline] tcp_v4_rcv+0x181a/0x1bb0 net/ipv4/tcp_ipv4.c:1934 ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204 ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252 dst_input include/net/dst.h:442 [inline] ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523 __netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010 __netif_receive_skb+0x37/0xf0 net/core/dev.c:5124 process_backlog+0x1d3/0x420 net/core/dev.c:5955 napi_poll net/core/dev.c:6392 [inline] net_rx_action+0x3ae/0xa90 net/core/dev.c:6460 __do_softirq+0x115/0x33f kernel/softirq.c:292 run_ksoftirqd+0x46/0x60 kernel/softirq.c:603 smpboot_thread_fn+0x37d/0x4a0 kernel/smpboot.c:165 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 16 Comm: ksoftirqd/1 Not tainted 5.4.0-rc3+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-30erspan: fix the tun_info options_len check for erspanXin Long1-2/+2
The check for !md doens't really work for ip_tunnel_info_opts(info) which only does info + 1. Also to avoid out-of-bounds access on info, it should ensure options_len is not less than erspan_metadata in both erspan_xmit() and ip6erspan_tunnel_xmit(). Fixes: 1a66a836da ("gre: add collect_md mode to ERSPAN tunnel") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-23ipv6: include <net/addrconf.h> for missing declarationsBen Dooks (Codethink)1-0/+1
Include <net/addrconf.h> for the missing declarations of various functions. Fixes the following sparse warnings: net/ipv6/addrconf_core.c:94:5: warning: symbol 'register_inet6addr_notifier' was not declared. Should it be static? net/ipv6/addrconf_core.c:100:5: warning: symbol 'unregister_inet6addr_notifier' was not declared. Should it be static? net/ipv6/addrconf_core.c:106:5: warning: symbol 'inet6addr_notifier_call_chain' was not declared. Should it be static? net/ipv6/addrconf_core.c:112:5: warning: symbol 'register_inet6addr_validator_notifier' was not declared. Should it be static? net/ipv6/addrconf_core.c:118:5: warning: symbol 'unregister_inet6addr_validator_notifier' was not declared. Should it be static? net/ipv6/addrconf_core.c:125:5: warning: symbol 'inet6addr_validator_notifier_call_chain' was not declared. Should it be static? net/ipv6/addrconf_core.c:237:6: warning: symbol 'in6_dev_finish_destroy' was not declared. Should it be static? Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-10-18net: ensure correct skb->tstamp in various fragmentersEric Dumazet2-0/+6
Thomas found that some forwarded packets would be stuck in FQ packet scheduler because their skb->tstamp contained timestamps far in the future. We thought we addressed this point in commit 8203e2d844d3 ("net: clear skb->tstamp in forwarding paths") but there is still an issue when/if a packet needs to be fragmented. In order to meet EDT requirements, we have to make sure all fragments get the original skb->tstamp. Note that this original skb->tstamp should be zero in forwarding path, but might have a non zero value in output path if user decided so. Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Thomas Bartschies <Thomas.Bartschies@cvk.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-16Revert "blackhole_netdev: fix syzkaller reported issue"Mahesh Bandewar2-12/+10
This reverts commit b0818f80c8c1bc215bba276bd61c216014fab23b. Started seeing weird behavior after this patch especially in the IPv6 code path. Haven't root caused it, but since this was applied to net branch, taking a precautionary measure to revert it and look / analyze those failures Revert this now and I'll send a better fix after analysing / fixing the weirdness observed. CC: Eric Dumazet <edumazet@google.com> CC: Wei Wang <weiwan@google.com> CC: David S. Miller <davem@davemloft.net> Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-15blackhole_netdev: fix syzkaller reported issueMahesh Bandewar2-10/+12
While invalidating the dst, we assign backhole_netdev instead of loopback device. However, this device does not have idev pointer and hence no ip6_ptr even if IPv6 is enabled. Possibly this has triggered the syzbot reported crash. The syzbot report does not have reproducer, however, this is the only device that doesn't have matching idev created. Crash instruction is : static inline bool ip6_ignore_linkdown(const struct net_device *dev) { const struct inet6_dev *idev = __in6_dev_get(dev); return !!idev->cnf.ignore_routes_with_linkdown; <= crash } Also ipv6 always assumes presence of idev and never checks for it being NULL (as does the above referenced code). So adding a idev for the blackhole_netdev to avoid this class of crashes in the future. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-13tcp: annotate tp->write_seq lockless readsEric Dumazet1-6/+7
There are few places where we fetch tp->write_seq while this field can change from IRQ or other cpu. We need to add READ_ONCE() annotations, and also make sure write sides use corresponding WRITE_ONCE() to avoid store-tearing. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-13tcp: annotate tp->copied_seq lockless readsEric Dumazet1-1/+1
There are few places where we fetch tp->copied_seq while this field can change from IRQ or other cpu. We need to add READ_ONCE() annotations, and also make sure write sides use corresponding WRITE_ONCE() to avoid store-tearing. Note that tcp_inq_hint() was already using READ_ONCE(tp->copied_seq) Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-13tcp: annotate tp->rcv_nxt lockless readsEric Dumazet1-1/+2
There are few places where we fetch tp->rcv_nxt while this field can change from IRQ or other cpu. We need to add READ_ONCE() annotations, and also make sure write sides use corresponding WRITE_ONCE() to avoid store-tearing. Note that tcp_inq_hint() was already using READ_ONCE(tp->rcv_nxt) syzbot reported : BUG: KCSAN: data-race in tcp_poll / tcp_queue_rcv write to 0xffff888120425770 of 4 bytes by interrupt on cpu 0: tcp_rcv_nxt_update net/ipv4/tcp_input.c:3365 [inline] tcp_queue_rcv+0x180/0x380 net/ipv4/tcp_input.c:4638 tcp_rcv_established+0xbf1/0xf50 net/ipv4/tcp_input.c:5616 tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1542 tcp_v4_rcv+0x1a03/0x1bf0 net/ipv4/tcp_ipv4.c:1923 ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204 ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252 dst_input include/net/dst.h:442 [inline] ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523 __netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004 __netif_receive_skb+0x37/0xf0 net/core/dev.c:5118 netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208 napi_skb_finish net/core/dev.c:5671 [inline] napi_gro_receive+0x28f/0x330 net/core/dev.c:5704 receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061 read to 0xffff888120425770 of 4 bytes by task 7254 on cpu 1: tcp_stream_is_readable net/ipv4/tcp.c:480 [inline] tcp_poll+0x204/0x6b0 net/ipv4/tcp.c:554 sock_poll+0xed/0x250 net/socket.c:1256 vfs_poll include/linux/poll.h:90 [inline] ep_item_poll.isra.0+0x90/0x190 fs/eventpoll.c:892 ep_send_events_proc+0x113/0x5c0 fs/eventpoll.c:1749 ep_scan_ready_list.constprop.0+0x189/0x500 fs/eventpoll.c:704 ep_send_events fs/eventpoll.c:1793 [inline] ep_poll+0xe3/0x900 fs/eventpoll.c:1930 do_epoll_wait+0x162/0x180 fs/eventpoll.c:2294 __do_sys_epoll_pwait fs/eventpoll.c:2325 [inline] __se_sys_epoll_pwait fs/eventpoll.c:2311 [inline] __x64_sys_epoll_pwait+0xcd/0x170 fs/eventpoll.c:2311 do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 7254 Comm: syz-fuzzer Not tainted 5.3.0+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-13tcp: add rcu protection around tp->fastopen_rskEric Dumazet1-1/+1
Both tcp_v4_err() and tcp_v6_err() do the following operations while they do not own the socket lock : fastopen = tp->fastopen_rsk; snd_una = fastopen ? tcp_rsk(fastopen)->snt_isn : tp->snd_una; The problem is that without appropriate barrier, the compiler might reload tp->fastopen_rsk and trigger a NULL deref. request sockets are protected by RCU, we can simply add the missing annotations and barriers to solve the issue. Fixes: 168a8f58059a ("tcp: TCP Fast Open Server - main code path") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-09ip6erspan: remove the incorrect mtu limit for ip6erspanHaishuang Yan1-0/+1
ip6erspan driver calls ether_setup(), after commit 61e84623ace3 ("net: centralize net_device min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which is [68, 1500] by default. It causes the dev mtu of the erspan device to not be greater than 1500, this limit value is not correct for ip6erspan tap device. Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking") Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-10-05ipv6: Handle missing host route in __ipv6_ifa_notifyDavid Ahern1-5/+12
Rajendra reported a kernel panic when a link was taken down: [ 6870.263084] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8 [ 6870.271856] IP: [<ffffffff8efc5764>] __ipv6_ifa_notify+0x154/0x290 <snip> [ 6870.570501] Call Trace: [ 6870.573238] [<ffffffff8efc58c6>] ? ipv6_ifa_notify+0x26/0x40 [ 6870.579665] [<ffffffff8efc98ec>] ? addrconf_dad_completed+0x4c/0x2c0 [ 6870.586869] [<ffffffff8efe70c6>] ? ipv6_dev_mc_inc+0x196/0x260 [ 6870.593491] [<ffffffff8efc9c6a>] ? addrconf_dad_work+0x10a/0x430 [ 6870.600305] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70 [ 6870.606732] [<ffffffff8ea93a7a>] ? process_one_work+0x18a/0x430 [ 6870.613449] [<ffffffff8ea93d6d>] ? worker_thread+0x4d/0x490 [ 6870.619778] [<ffffffff8ea93d20>] ? process_one_work+0x430/0x430 [ 6870.626495] [<ffffffff8ea99dd9>] ? kthread+0xd9/0xf0 [ 6870.632145] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70 [ 6870.638573] [<ffffffff8ea99d00>] ? kthread_park+0x60/0x60 [ 6870.644707] [<ffffffff8f01ae77>] ? ret_from_fork+0x57/0x70 [ 6870.650936] Code: 31 c0 31 d2 41 b9 20 00 08 02 b9 09 00 00 0 addrconf_dad_work is kicked to be scheduled when a device is brought up. There is a race between addrcond_dad_work getting scheduled and taking the rtnl lock and a process taking the link down (under rtnl). The latter removes the host route from the inet6_addr as part of addrconf_ifdown which is run for NETDEV_DOWN. The former attempts to use the host route in __ipv6_ifa_notify. If the down event removes the host route due to the race to the rtnl, then the BUG listed above occurs. Since the DAD sequence can not be aborted, add a check for the missing host route in __ipv6_ifa_notify. The only way this should happen is due to the previously mentioned race. The host route is created when the address is added to an interface; it is only removed on a down event where the address is kept. Add a warning if the host route is missing AND the device is up; this is a situation that should never happen. Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional") Reported-by: Rajendra Dendukuri <rajendra.dendukuri@broadcom.com> Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-05Revert "ipv6: Handle race in addrconf_dad_work"David Ahern1-6/+5
This reverts commit a3ce2a21bb8969ae27917281244fa91bf5f286d7. Eric reported tests failings with commit. After digging into it, the bottom line is that the DAD sequence is not to be messed with. There are too many cases that are expected to proceed regardless of whether a device is up. Revert the patch and I will send a different solution for the problem Rajendra reported. Signed-off-by: David Ahern <dsahern@gmail.com> Cc: Eric Dumazet <edumazet@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-03udp: only do GSO if # of segs > 1Josh Hunt1-4/+7
Prior to this change an application sending <= 1MSS worth of data and enabling UDP GSO would fail if the system had SW GSO enabled, but the same send would succeed if HW GSO offload is enabled. In addition to this inconsistency the error in the SW GSO case does not get back to the application if sending out of a real device so the user is unaware of this failure. With this change we only perform GSO if the # of segments is > 1 even if the application has enabled segmentation. I've also updated the relevant udpgso selftests. Fixes: bec1f6f69736 ("udp: generate gso with UDP_SEGMENT") Signed-off-by: Josh Hunt <johunt@akamai.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-03udp: fix gso_segs calculationsJosh Hunt1-0/+2
Commit dfec0ee22c0a ("udp: Record gso_segs when supporting UDP segmentation offload") added gso_segs calculation, but incorrectly got sizeof() the pointer and not the underlying data type. In addition let's fix the v6 case. Fixes: bec1f6f69736 ("udp: generate gso with UDP_SEGMENT") Fixes: dfec0ee22c0a ("udp: Record gso_segs when supporting UDP segmentation offload") Signed-off-by: Josh Hunt <johunt@akamai.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-03ipv6: drop incoming packets having a v4mapped source addressEric Dumazet1-0/+10
This began with a syzbot report. syzkaller was injecting IPv6 TCP SYN packets having a v4mapped source address. After an unsuccessful 4-tuple lookup, TCP creates a request socket (SYN_RECV) and calls reqsk_queue_hash_req() reqsk_queue_hash_req() calls sk_ehashfn(sk) At this point we have AF_INET6 sockets, and the heuristic used by sk_ehashfn() to either hash the IPv4 or IPv6 addresses is to use ipv6_addr_v4mapped(&sk->sk_v6_daddr) For the particular spoofed packet, we end up hashing V4 addresses which were not initialized by the TCP IPv6 stack, so KMSAN fired a warning. I first fixed sk_ehashfn() to test both source and destination addresses, but then faced various problems, including user-space programs like packetdrill that had similar assumptions. Instead of trying to fix the whole ecosystem, it is better to admit that we have a dual stack behavior, and that we can not build linux kernels without V4 stack anyway. The dual stack API automatically forces the traffic to be IPv4 if v4mapped addresses are used at bind() or connect(), so it makes no sense to allow IPv6 traffic to use the same v4mapped class. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Florian Westphal <fw@strlen.de> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller3-3/+3
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for net: 1) Remove the skb_ext_del from nf_reset, and renames it to a more fitting nf_reset_ct(). Patch from Florian Westphal. 2) Fix deadlock in nft_connlimit between packet path updates and the garbage collector. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-02ipv6: Handle race in addrconf_dad_workDavid Ahern1-5/+6
Rajendra reported a kernel panic when a link was taken down: [ 6870.263084] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8 [ 6870.271856] IP: [<ffffffff8efc5764>] __ipv6_ifa_notify+0x154/0x290 <snip> [ 6870.570501] Call Trace: [ 6870.573238] [<ffffffff8efc58c6>] ? ipv6_ifa_notify+0x26/0x40 [ 6870.579665] [<ffffffff8efc98ec>] ? addrconf_dad_completed+0x4c/0x2c0 [ 6870.586869] [<ffffffff8efe70c6>] ? ipv6_dev_mc_inc+0x196/0x260 [ 6870.593491] [<ffffffff8efc9c6a>] ? addrconf_dad_work+0x10a/0x430 [ 6870.600305] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70 [ 6870.606732] [<ffffffff8ea93a7a>] ? process_one_work+0x18a/0x430 [ 6870.613449] [<ffffffff8ea93d6d>] ? worker_thread+0x4d/0x490 [ 6870.619778] [<ffffffff8ea93d20>] ? process_one_work+0x430/0x430 [ 6870.626495] [<ffffffff8ea99dd9>] ? kthread+0xd9/0xf0 [ 6870.632145] [<ffffffff8f01ade4>] ? __switch_to_asm+0x34/0x70 [ 6870.638573] [<ffffffff8ea99d00>] ? kthread_park+0x60/0x60 [ 6870.644707] [<ffffffff8f01ae77>] ? ret_from_fork+0x57/0x70 [ 6870.650936] Code: 31 c0 31 d2 41 b9 20 00 08 02 b9 09 00 00 0 addrconf_dad_work is kicked to be scheduled when a device is brought up. There is a race between addrcond_dad_work getting scheduled and taking the rtnl lock and a process taking the link down (under rtnl). The latter removes the host route from the inet6_addr as part of addrconf_ifdown which is run for NETDEV_DOWN. The former attempts to use the host route in ipv6_ifa_notify. If the down event removes the host route due to the race to the rtnl, then the BUG listed above occurs. This scenario does not occur when the ipv6 address is not kept (net.ipv6.conf.all.keep_addr_on_down = 0) as addrconf_ifdown sets the state of the ifp to DEAD. Handle when the addresses are kept by checking IF_READY which is reset by addrconf_ifdown. The 'dead' flag for an inet6_addr is set only under rtnl, in addrconf_ifdown and it means the device is getting removed (or IPv6 is disabled). The interesting cases for changing the idev flag are addrconf_notify (NETDEV_UP and NETDEV_CHANGE) and addrconf_ifdown (reset the flag). The former does not have the idev lock - only rtnl; the latter has both. Based on that the existing dead + IF_READY check can be moved to right after the rtnl_lock in addrconf_dad_work. Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional") Reported-by: Rajendra Dendukuri <rajendra.dendukuri@broadcom.com> Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-01netfilter: drop bridge nf reset from nf_resetFlorian Westphal3-3/+3
commit 174e23810cd31 ("sk_buff: drop all skb extensions on free and skb scrubbing") made napi recycle always drop skb extensions. The additional skb_ext_del() that is performed via nf_reset on napi skb recycle is not needed anymore. Most nf_reset() calls in the stack are there so queued skb won't block 'rmmod nf_conntrack' indefinitely. This removes the skb_ext_del from nf_reset, and renames it to a more fitting nf_reset_ct(). In a few selected places, add a call to skb_ext_reset to make sure that no active extensions remain. I am submitting this for "net", because we're still early in the release cycle. The patch applies to net-next too, but I think the rename causes needless divergence between those trees. Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2019-09-27tcp: honor SO_PRIORITY in TIME_WAIT stateEric Dumazet1-2/+4
ctl packets sent on behalf of TIME_WAIT sockets currently have a zero skb->priority, which can cause various problems. In this patch we : - add a tw_priority field in struct inet_timewait_sock. - populate it from sk->sk_priority when a TIME_WAIT is created. - For IPv4, change ip_send_unicast_reply() and its two callers to propagate tw_priority correctly. ip_send_unicast_reply() no longer changes sk->sk_priority. - For IPv6, make sure TIME_WAIT sockets pass their tw_priority field to tcp_v6_send_response() and tcp_v6_send_ack(). Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-27ipv6: tcp: provide sk->sk_priority to ctl packetsEric Dumazet1-7/+9
We can populate skb->priority for some ctl packets instead of always using zero. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-08-02 03:50:36 +0300