From efdbd7345f8836f7495f3ac6ee237d86cb3bb6b0 Mon Sep 17 00:00:00 2001 From: Rob Herring Date: Mon, 21 Sep 2015 10:51:09 -0500 Subject: dt-bindings: consolidate display related bindings This is a quite large renaming to consolidate display related bindings into a single "display" directory from various scattered locations of video, drm, gpu, fb, mipi, and panel. The prior location was somewhat based on the Linux driver location, but bindings should be independent of that. Signed-off-by: Rob Herring Cc: Pawel Moll Cc: Mark Rutland Cc: Ian Campbell Cc: Kumar Gala --- .../devicetree/bindings/display/msm/edp.txt | 60 ++++++++++++++++++++++ 1 file changed, 60 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/msm/edp.txt (limited to 'Documentation/devicetree/bindings/display/msm/edp.txt') diff --git a/Documentation/devicetree/bindings/display/msm/edp.txt b/Documentation/devicetree/bindings/display/msm/edp.txt new file mode 100644 index 000000000000..3a20f6ea5898 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/edp.txt @@ -0,0 +1,60 @@ +Qualcomm Technologies Inc. adreno/snapdragon eDP output + +Required properties: +- compatible: + * "qcom,mdss-edp" +- reg: Physical base address and length of the registers of controller and PLL +- reg-names: The names of register regions. The following regions are required: + * "edp" + * "pll_base" +- interrupts: The interrupt signal from the eDP block. +- power-domains: Should be <&mmcc MDSS_GDSC>. +- clocks: device clocks + See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "core_clk" + * "iface_clk" + * "mdp_core_clk" + * "pixel_clk" + * "link_clk" +- #clock-cells: The value should be 1. +- vdda-supply: phandle to vdda regulator device node +- lvl-vdd-supply: phandle to regulator device node which is used to supply power + to HPD receiving chip +- panel-en-gpios: GPIO pin to supply power to panel. +- panel-hpd-gpios: GPIO pin used for eDP hpd. + + +Optional properties: +- interrupt-parent: phandle to the MDP block if the interrupt signal is routed + through MDP block + +Example: + mdss_edp: qcom,mdss_edp@fd923400 { + compatible = "qcom,mdss-edp"; + reg-names = + "edp", + "pll_base"; + reg = <0xfd923400 0x700>, + <0xfd923a00 0xd4>; + interrupt-parent = <&mdss_mdp>; + interrupts = <12 0>; + power-domains = <&mmcc MDSS_GDSC>; + clock-names = + "core_clk", + "pixel_clk", + "iface_clk", + "link_clk", + "mdp_core_clk"; + clocks = + <&mmcc MDSS_EDPAUX_CLK>, + <&mmcc MDSS_EDPPIXEL_CLK>, + <&mmcc MDSS_AHB_CLK>, + <&mmcc MDSS_EDPLINK_CLK>, + <&mmcc MDSS_MDP_CLK>; + #clock-cells = <1>; + vdda-supply = <&pma8084_l12>; + lvl-vdd-supply = <&lvl_vreg>; + panel-en-gpios = <&tlmm 137 0>; + panel-hpd-gpios = <&tlmm 103 0>; + }; -- cgit v1.2.3