Merge tag '0.70' of ssh://git-amr-1.devtools.intel.com:29418/openbmc-openbmc into update

24 files changed, 521 insertions, 15 deletions

diff --git a/meta-ampere/meta-jade/conf/machine/mtjade.conf b/meta-ampere/meta-jade/conf/machine/mtjade.conf
index 171a023f4..43a1059dd 100644
--- a/meta-ampere/meta-jade/conf/machine/mtjade.conf
+++ b/meta-ampere/meta-jade/conf/machine/mtjade.conf
@@ -25,9 +25,12 @@ OBMC_MACHINE_FEATURES += "\
 VOLATILE_LOG_DIR = "no"
 
 OBMC_IMAGE_EXTRA_INSTALL_append = "\
+                                   mtjade-utils \
                                    ampere-usbnet \
                                    ampere-flash-utils \
                                    ampere-mac-update \
+                                   mtjade-gpio-config \
+                                   mtd-utils \
                                   "
 
 PREFERRED_PROVIDER_virtual/obmc-chassis-mgmt = "packagegroup-ampere-apps"
diff --git a/meta-ampere/meta-jade/recipes-ampere/flash/ampere-flash-utils/ampere_flash_bios.sh b/meta-ampere/meta-jade/recipes-ampere/flash/ampere-flash-utils/ampere_flash_bios.sh
index 876671c1b..7a9ace30e 100755
--- a/meta-ampere/meta-jade/recipes-ampere/flash/ampere-flash-utils/ampere_flash_bios.sh
+++ b/meta-ampere/meta-jade/recipes-ampere/flash/ampere-flash-utils/ampere_flash_bios.sh
@@ -15,6 +15,8 @@
 # limitations under the License.
 
 do_flash () {
+        OFFSET=$1
+
 	# Check the PNOR partition available
 	HOST_MTD=$(cat /proc/mtd | grep "pnor" | sed -n 's/^\(.*\):.*/\1/p')
 	if [ -z "$HOST_MTD" ];
@@ -30,18 +32,10 @@ do_flash () {
 			echo "Fail to probe Host SPI-NOR device"
 			exit 1
 		fi
-
-		echo "--- Flashing firmware to @/dev/$HOST_MTD"
-		flash_eraseall /dev/$HOST_MTD
-		flashcp -v $IMAGE /dev/$HOST_MTD
-
-		echo "--- Unbind the ASpeed SMC driver"
-		echo 1e630000.spi > /sys/bus/platform/drivers/aspeed-smc/unbind
-	else
-		echo "--- Flashing firmware to @/dev/$HOST_MTD"
-		flash_eraseall /dev/$HOST_MTD
-		flashcp -v $IMAGE /dev/$HOST_MTD
 	fi
+
+	echo "--- Flashing firmware to @/dev/$HOST_MTD offset=$OFFSET"
+	flashcp -v $IMAGE /dev/$HOST_MTD $OFFSET
 }
 
 
@@ -84,7 +78,7 @@ if [[ $? -ne 0 ]]; then
 fi
 
 # Flash the firmware
-do_flash
+do_flash 0x400000
 
 # Switch the host SPI bus to HOST."
 echo "--- Switch the host SPI bus to HOST."
@@ -99,5 +93,5 @@ if [ "$chassisstate" == 'On' ];
 then
 	sleep 5
 	echo "Turn on the Host"
-	obmcutil chassison
+	obmcutil poweron
 fi
diff --git a/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config.bb b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config.bb
new file mode 100644
index 000000000..69fedd67a
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config.bb
@@ -0,0 +1,44 @@
+SUMMARY = "Ampere Computing LLC Utilities"
+DESCRIPTION = "Ampere Utilities for Mt.Jade systems"
+PR = "r1"
+LICENSE = "Apache-2.0"
+LIC_FILES_CHKSUM = "file://${COMMON_LICENSE_DIR}/Apache-2.0;md5=89aea4e17d99a7cacdbeed46a0096b10"
+
+inherit systemd
+inherit obmc-phosphor-systemd
+
+S = "${WORKDIR}"
+
+SRC_URI = " \
+          file://ampere_gpio_utils.sh \
+          "
+
+DEPENDS = "systemd"
+RDEPENDS_${PN} = "bash"
+
+SYSTEMD_PACKAGES = "${PN}"
+
+SYSTEMD_SERVICE_${PN} = " \
+        ampere-gpio-poweroff@.service \
+        ampere-gpio-poweron@.service \
+        "
+
+# chassis power on
+CHASSIS_POWERON_SVC = "ampere-gpio-poweron@.service"
+CHASSIS_POWERON_INSTMPL = "ampere-gpio-poweron@{0}.service"
+CHASSIS_POWERON_TGTFMT = "obmc-chassis-poweron@{0}.target"
+CHASSIS_POWERON_FMT = "../${CHASSIS_POWERON_SVC}:${CHASSIS_POWERON_TGTFMT}.requires/${CHASSIS_POWERON_INSTMPL}"
+SYSTEMD_LINK_${PN} += "${@compose_list_zip(d, 'CHASSIS_POWERON_FMT', 'OBMC_CHASSIS_INSTANCES')}"
+
+# chassis power off
+CHASSIS_POWEROFF_SVC = "ampere-gpio-poweroff@.service"
+CHASSIS_POWEROFF_INSTMPL = "ampere-gpio-poweroff@{0}.service"
+CHASSIS_POWEROFF_TGTFMT = "obmc-chassis-poweroff@{0}.target"
+CHASSIS_POWEROFF_FMT = "../${CHASSIS_POWEROFF_SVC}:${CHASSIS_POWEROFF_TGTFMT}.requires/${CHASSIS_POWEROFF_INSTMPL}"
+SYSTEMD_LINK_${PN} += "${@compose_list_zip(d, 'CHASSIS_POWEROFF_FMT', 'OBMC_CHASSIS_INSTANCES')}"
+
+do_install() {
+    install -d ${D}/usr/sbin
+    install -m 0755 ${WORKDIR}/ampere_gpio_utils.sh ${D}/${sbindir}/
+}
+
diff --git a/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config/ampere-gpio-poweroff@.service b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config/ampere-gpio-poweroff@.service
new file mode 100644
index 000000000..78862eb32
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config/ampere-gpio-poweroff@.service
@@ -0,0 +1,10 @@
+[Unit]
+Description=Ampere set GPIOs before power off
+Requires=op-wait-power-off@%i.service
+Before=op-wait-power-off@%i.service
+Conflicts=obmc-chassis-poweron@%i.target
+
+[Service]
+Type=oneshot
+ExecStart=/usr/bin/env ampere_gpio_utils.sh power off
+SyslogIdentifier=ampere_gpio_utils
\ No newline at end of file
diff --git a/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config/ampere-gpio-poweron@.service b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config/ampere-gpio-poweron@.service
new file mode 100644
index 000000000..09aa58826
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config/ampere-gpio-poweron@.service
@@ -0,0 +1,10 @@
+[Unit]
+Description=Ampere set GPIOs before power on
+Requires=op-wait-power-on@%i.service
+Before=op-wait-power-on@%i.service
+Conflicts=obmc-chassis-poweroff@%i.target
+
+[Service]
+Type=oneshot
+ExecStart=/usr/bin/env ampere_gpio_utils.sh power on
+SyslogIdentifier=ampere_gpio_utils
diff --git a/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config/ampere_gpio_utils.sh b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config/ampere_gpio_utils.sh
new file mode 100644
index 000000000..8e4f455bf
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-gpio-config/ampere_gpio_utils.sh
@@ -0,0 +1,43 @@
+#!/bin/bash
+source /usr/sbin/gpio-defs.sh
+source /usr/sbin/gpio-lib.sh
+
+function usage() {
+    echo "usage: ampere_gpio_utils.sh [power] [on|off]";
+}
+
+set_gpio_power_off() {
+    echo "Setting GPIO before Power off"
+    gpio_configure_output $OCP_AUX_PWREN 1
+    gpio_configure_output $OCP_MAIN_PWREN 0
+    gpio_configure_output $SPI0_PROGRAM_SEL 0
+}
+
+set_gpio_power_on() {
+    echo "Setting GPIO before Power on"
+    gpio_configure_output $OCP_AUX_PWREN 1
+    gpio_configure_output $OCP_MAIN_PWREN 1
+    gpio_configure_output $SPI0_PROGRAM_SEL 1
+    gpio_configure_output $SPI0_BACKUP_SEL 0
+}
+
+if [ $# -lt 2 ]; then
+    echo "Total number of parameter=$#"
+    echo "Insufficient parameter"
+    usage;
+    exit 0;
+fi
+
+if [ $1 == "power" ]; then
+    if [ $2 == "on" ]; then
+        set_gpio_power_on
+    elif [ $2 == "off" ]; then
+        set_gpio_power_off
+    fi
+    exit 0;
+else
+    echo "Invalid parameter1=$1"
+    usage;
+    exit 0;
+fi
+exit 0;
diff --git a/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils.bb b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils.bb
new file mode 100644
index 000000000..159ccdd64
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils.bb
@@ -0,0 +1,22 @@
+SUMMARY = "Ampere Platform Environment Definitions"
+DESCRIPTION = "Ampere Platform Environment Definitions"
+PR = "r1"
+LICENSE = "Apache-2.0"
+LIC_FILES_CHKSUM = "file://${COMMON_LICENSE_DIR}/Apache-2.0;md5=89aea4e17d99a7cacdbeed46a0096b10"
+
+SRC_URI = " \
+          file://gpio-defs.sh \
+          file://gpio-lib.sh \
+          file://ampere_power_util.sh \
+          file://ampere_host_check.sh \
+          "
+
+RDEPENDS_${PN} = "bash"
+
+do_install() {
+    install -d ${D}/usr/sbin
+    install -m 0755 ${WORKDIR}/gpio-lib.sh ${D}/${sbindir}/
+    install -m 0755 ${WORKDIR}/gpio-defs.sh ${D}/${sbindir}/
+    install -m 0755 ${WORKDIR}/ampere_power_util.sh ${D}/${sbindir}/
+    install -m 0755 ${WORKDIR}/ampere_host_check.sh ${D}/${sbindir}/
+}
\ No newline at end of file
diff --git a/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/ampere_host_check.sh b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/ampere_host_check.sh
new file mode 100644
index 000000000..9eeeeca5a
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/ampere_host_check.sh
@@ -0,0 +1,45 @@
+#!/bin/bash
+
+source /usr/sbin/gpio-defs.sh
+source /usr/sbin/gpio-lib.sh
+
+host_status() {
+    st=$(busctl get-property xyz.openbmc_project.State.Host /xyz/openbmc_project/state/host0 xyz.openbmc_project.State.Host CurrentHostState | cut -d"." -f6)
+    if [ "$st" == "Running\"" ]; then
+        echo "on"
+    else
+        echo "off"
+    fi
+}
+
+createFile=$1
+setState=$2
+
+if [ $(host_status) == "on" ]; then
+    exit 0
+fi
+
+# Time out to check S0_FW_BOOT_OK is 60 seconds
+cnt=60
+val=0
+while [ $cnt -gt 0 ];
+do
+    val=$(gpio_get_val $S0_CPU_FW_BOOT_OK)
+    cnt=$((cnt - 1))
+    echo "$cnt S0_CPU_FW_BOOT_OK = $val"
+    if [ $val == 1 ]; then
+        # Sleep 5 second before the host is ready
+        sleep 5
+        if [ $createFile == 1 ]; then
+            if [ ! -d "/run/openbmc" ]; then
+                mkdir -p /run/openbmc
+            fi
+            echo "Creating /run/openbmc/host@0-on"
+            touch /run/openbmc/host@0-on
+        fi
+        exit 0
+    fi
+    sleep 1
+done
+
+exit 1
diff --git a/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/ampere_power_util.sh b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/ampere_power_util.sh
new file mode 100644
index 000000000..2c8ba3d91
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/ampere_power_util.sh
@@ -0,0 +1,131 @@
+#!/bin/bash
+#ampere_platform_config.sh is platform configuration file
+source /usr/sbin/gpio-defs.sh
+
+# Usage of this utility
+function usage() {
+  echo "usage: power-util mb [status|shutdown_ack|force_reset|soft_off]";
+}
+
+power_status() {
+  st=$(busctl get-property xyz.openbmc_project.State.Chassis /xyz/openbmc_project/state/chassis0 xyz.openbmc_project.State.Chassis CurrentPowerState | cut -d"." -f6)
+  if [ "$st" == "On\"" ]; then
+  echo "on"
+  else
+  echo "off"
+  fi
+}
+
+shutdown_ack() {
+  if [ -f "/run/openbmc/host@0-softpoweroff" ]; then
+    echo "Receive shutdown ACK triggered after softportoff the host."
+    touch /run/openbmc/host@0-softpoweroff-shutdown-ack
+  else
+    echo "Receive shutdown ACK triggered"
+    sleep 3
+    systemctl start obmc-chassis-poweroff@0.target
+  fi
+}
+
+soft_off() {
+  # Trigger shutdown_req
+  touch /run/openbmc/host@0-softpoweroff
+  gpioset -l $GPIO_CHIP0_IDX $S0_SHD_REQ_L=1
+  sleep 1s
+  gpioset -l $GPIO_CHIP0_IDX $S0_SHD_REQ_L=0
+
+  # Wait for shutdown_ack from the host in 30 seconds
+  cnt=30
+  while [ $cnt -gt 0 ];
+  do
+    # Wait for SHUTDOWN_ACK and create the host@0-softpoweroff-shutdown-ack
+    if [ -f "/run/openbmc/host@0-softpoweroff-shutdown-ack" ]; then
+      break
+    fi
+    sleep 1
+    cnt=$((cnt - 1))
+  done
+  # Softpoweroff is successed
+  sleep 2
+  rm -rf /run/openbmc/host@0-softpoweroff
+  if [ -f "/run/openbmc/host@0-softpoweroff-shutdown-ack" ]; then
+    rm -rf /run/openbmc/host@0-softpoweroff-shutdown-ack
+  fi
+  echo 0
+}
+
+force_reset() {
+  if [ -f "/run/openbmc/host@0-softpoweroff" ]; then
+    # In graceful host reset, after trigger os shutdown,
+    # the phosphor-state-manager will call force-warm-reset
+    # in this case the force_reset should wait for shutdown_ack from host
+    cnt=30
+    while [ $cnt -gt 0 ];
+    do
+      if [ -f "/run/openbmc/host@0-softpoweroff-shutdown-ack" ]; then
+        break
+      fi
+      echo "Waiting for shutdown-ack count down $cnt"
+      sleep 1
+      cnt=$((cnt - 1))
+    done
+    # The host OS is failed to shutdown
+    if [ $cnt == 0 ]; then
+      echo "Shutdown-ack time out after 30s."
+      exit 0
+    fi
+  fi
+  echo "Triggering sysreset pin"
+  gpioset -l $GPIO_CHIP0_IDX $S0_SYSRESET_L=1
+  sleep 1
+  gpioset -l $GPIO_CHIP0_IDX $S0_SYSRESET_L=0
+}
+
+if [ $# -lt 2 ]; then
+  echo "Total number of parameter=$#"
+  echo "Insufficient parameter"
+  usage;
+  exit 0;
+fi
+
+if [ $1 != "mb" ]; then
+  echo "Invalid parameter1=$1"
+  usage;
+  exit 0;
+fi
+
+# check if power guard enabled
+dir="/run/systemd/system/"
+file="reboot-guard.conf"
+units=("reboot" "poweroff" "halt")
+for unit in "${units[@]}"; do
+  if [ -f ${dir}${unit}.target.d/${file} ]; then
+    echo "PowerGuard enabled, cannot do power control, exit!!!"
+    exit -1
+  fi
+done
+
+if [ ! -d "/run/openbmc/" ]; then
+  mkdir -p "/run/openbmc/"
+fi
+
+if [ $2 == "shutdown_ack" ]; then
+  shutdown_ack
+elif [ $2 == "status" ]; then
+  power_status
+elif [ $2 == "force_reset" ]; then
+  force_reset
+elif [ $2 == "soft_off" ]; then
+  ret=$(soft_off)
+  if [ $ret == 0 ]; then
+    echo "The host is already softoff"
+  else
+    echo "Failed to softoff the host"
+  fi
+  exit $ret;
+else
+  echo "Invalid parameter2=$2"
+  usage;
+fi
+
+exit 0;
diff --git a/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/gpio-defs.sh b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/gpio-defs.sh
new file mode 100644
index 000000000..7c887d409
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/gpio-defs.sh
@@ -0,0 +1,40 @@
+# Index of GPIO device in gpioget/gpioset
+GPIO_CHIP0_IDX=0
+GPIO_CHIP1_IDX=1
+
+# Base of GPIO chip in /sys/class/gpio
+GPIO_CHIP0_BASE=792
+GPIO_CHIP1_BASE=780
+
+### Power control configuration
+# Power control gpios
+S0_SHD_REQ_L=49
+S0_SHD_ACK_L=50
+S0_REBOOT_ACK_L=75
+S0_SYSRESET_L=91
+
+
+### Table 1: GPIO Assignments
+S0_CPU_FW_BOOT_OK=48
+CPU_BMC_OVERTEMP_L=51
+CPU_BMC_HIGHTEMP_L=72
+CPU_FAULT_ALERT=73
+S1_CPU_FW_BOOT_OK=202
+
+### Table 2: Alert and Additional Miscellaneous Signals
+S0_SCP_AUTH_FAILURE=74
+S1_SCP_AUTH_FAILURE=205
+BMC_OK=228
+SLAVE_PRESENT_L=230
+
+### Common GPIOs
+SYS_PSON_L=42
+BMC_READY=229
+
+### OCP power selection
+OCP_AUX_PWREN=139
+OCP_MAIN_PWREN=140
+
+### SPI0 Mode  selection
+SPI0_PROGRAM_SEL=226
+SPI0_BACKUP_SEL=227
diff --git a/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/gpio-lib.sh b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/gpio-lib.sh
new file mode 100644
index 000000000..8d1aa61d7
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-ampere/platform/mtjade-utils/gpio-lib.sh
@@ -0,0 +1,31 @@
+#!/bin/bash
+source /usr/sbin/gpio-defs.sh
+
+function gpio_number() {
+	GPIO_BASE=$(cat /sys/class/gpio/gpiochip$GPIO_CHIP0_BASE/base)
+	echo $((${GPIO_BASE} + $1))
+}
+
+# Configure GPIO as output and set its value
+function gpio_configure_output() {
+	gpioId=$(gpio_number $1)
+	echo $gpioId > /sys/class/gpio/export
+	echo out > /sys/class/gpio/gpio${gpioId}/direction
+	echo $2 > /sys/class/gpio/gpio${gpioId}/value
+	echo $gpioId > /sys/class/gpio/unexport
+}
+
+function gpio_get_val() {
+	gpioId=$(gpio_number $1)
+	echo $gpioId > /sys/class/gpio/export
+	echo $(cat /sys/class/gpio/gpio$gpioId/value)
+	echo $gpioId > /sys/class/gpio/unexport
+}
+
+# Configure GPIO as input
+function gpio_configure_input() {
+	gpioId=$(gpio_number $1)
+	echo $gpioId > /sys/class/gpio/export
+	echo "in" > /sys/class/gpio/gpio${gpioId}/direction
+	echo $gpioId > /sys/class/gpio/unexport
+}
diff --git a/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling.bb b/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling.bb
new file mode 100644
index 000000000..4358b1242
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling.bb
@@ -0,0 +1,23 @@
+SUMMARY = "Ampere Computing LLC Host Gpio Handling"
+PR = "r1"
+LICENSE = "Apache-2.0"
+LIC_FILES_CHKSUM = "file://${COMMON_LICENSE_DIR}/Apache-2.0;md5=89aea4e17d99a7cacdbeed46a0096b10"
+
+inherit obmc-phosphor-systemd
+
+DEPENDS += "virtual/obmc-gpio-monitor"
+RDEPENDS_${PN} += "virtual/obmc-gpio-monitor"
+
+OBMC_HOST_ACK_MONITOR_INSTANCES = "reboot_ack shutdown_ack"
+
+SYSTEMD_ENVIRONMENT_FILE_${PN} +="obmc/gpio/reboot_ack \
+                                  obmc/gpio/shutdown_ack \
+                                 "
+
+TMPL = "phosphor-gpio-monitor@.service"
+INSTFMT = "phosphor-gpio-monitor@{0}.service"
+TGT = "multi-user.target"
+FMT = "../${TMPL}:${TGT}.requires/${INSTFMT}"
+
+SYSTEMD_SERVICE_${PN} += "ampere-host-shutdown-ack@.service"
+SYSTEMD_LINK_${PN} += "${@compose_list(d, 'FMT', 'OBMC_HOST_ACK_MONITOR_INSTANCES')}"
diff --git a/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling/ampere-host-shutdown-ack@.service b/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling/ampere-host-shutdown-ack@.service
new file mode 100644
index 000000000..6588191aa
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling/ampere-host-shutdown-ack@.service
@@ -0,0 +1,8 @@
+[Unit]
+Description=Ampere Computing LLC host shutdown ACK
+Conflicts=obmc-chassis-poweron@0.target
+
+[Service]
+Type=oneshot
+ExecStart=/usr/bin/env ampere_power_util.sh mb shutdown_ack
+SyslogIdentifier=ampere_host_shutdown_ack
diff --git a/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling/obmc/gpio/reboot_ack b/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling/obmc/gpio/reboot_ack
new file mode 100644
index 000000000..a8ad98ee7
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling/obmc/gpio/reboot_ack
@@ -0,0 +1,4 @@
+DEVPATH=/dev/input/event0
+KEY=75
+POLARITY=1
+TARGET=obmc-host-force-warm-reboot@0.target
diff --git a/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling/obmc/gpio/shutdown_ack b/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling/obmc/gpio/shutdown_ack
new file mode 100644
index 000000000..18cc87246
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-phosphor/gpio/host-gpio-handling/obmc/gpio/shutdown_ack
@@ -0,0 +1,4 @@
+DEVPATH=/dev/input/event0
+KEY=50
+POLARITY=1
+TARGET=ampere-host-shutdown-ack@0.service
diff --git a/meta-ampere/meta-jade/recipes-phosphor/inventory/inventory-cleanup/inventory-cleanup.yaml b/meta-ampere/meta-jade/recipes-phosphor/inventory/inventory-cleanup/inventory-cleanup.yaml
index e900ad789..3fa190852 100644
--- a/meta-ampere/meta-jade/recipes-phosphor/inventory/inventory-cleanup/inventory-cleanup.yaml
+++ b/meta-ampere/meta-jade/recipes-phosphor/inventory/inventory-cleanup/inventory-cleanup.yaml
@@ -12,5 +12,5 @@ events:
                 /system/chassis:
                   xyz.openbmc_project.Inventory.Item.Chassis:
                       Type:
-                          value: "RackMount"
+                          value: "xyz.openbmc_project.Inventory.Item.Chassis.ChassisType.RackMount"
                           type: string
diff --git a/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-host/ampere-phosphor-softpoweroff b/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-host/ampere-phosphor-softpoweroff
new file mode 100644
index 000000000..214aeed7a
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-host/ampere-phosphor-softpoweroff
@@ -0,0 +1,5 @@
+#!/bin/bash
+# Usage of this utility
+echo "Trigger soft off the host."
+/usr/sbin/ampere_power_util.sh mb soft_off
+exit $?;
diff --git a/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-host/ampere.xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service b/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-host/ampere.xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service
new file mode 100644
index 000000000..01b31b1b3
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-host/ampere.xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service
@@ -0,0 +1,13 @@
+[Unit]
+Description=Ampere Soft power off of the host
+Wants=obmc-host-stop-pre@0.target
+Before=obmc-host-stop-pre@0.target
+Conflicts=obmc-host-start@0.target
+ConditionPathExists=!/run/openbmc/host@0-request
+ConditionPathExists=!/lib/systemd/system/pldmSoftPowerOff.service
+
+[Service]
+Restart=no
+ExecStart=/usr/bin/env phosphor-softpoweroff
+SyslogIdentifier=phosphor-softpoweroff
+Type=oneshot
diff --git a/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-host_%.bbappend b/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-host_%.bbappend
index c0bcbdd3a..b8ea8d8d5 100644
--- a/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-host_%.bbappend
+++ b/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-host_%.bbappend
@@ -3,13 +3,23 @@ FILESEXTRAPATHS_append_mtjade := "${THISDIR}/${PN}:"
 DEPENDS_append_mtjade = " mtjade-yaml-config"
 
 RRECOMMENDS_${PN} += "ipmitool"
+RDEPENDS_${PN} += "bash"
+
+SRC_URI += " \
+            file://ampere-phosphor-softpoweroff \
+            file://ampere.xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service \
+            "
 
 EXTRA_OECONF_mtjade = " \
     SENSOR_YAML_GEN=${STAGING_DIR_HOST}${datadir}/mtjade-yaml-config/ipmi-sensors-${MACHINE}.yaml \
     FRU_YAML_GEN=${STAGING_DIR_HOST}${datadir}/mtjade-yaml-config/ipmi-fru-read.yaml \
     "
 
+AMPERE_SOFTPOWEROFF_TMPL = "ampere.xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service"
+
 do_install_append_mtjade(){
     install -d ${D}${includedir}/phosphor-ipmi-host
     install -m 0644 -D ${S}/selutility.hpp ${D}${includedir}/phosphor-ipmi-host
+    install -m 0755 ${WORKDIR}/ampere-phosphor-softpoweroff ${D}/${bindir}/phosphor-softpoweroff
+    install -m 0644 ${WORKDIR}/${AMPERE_SOFTPOWEROFF_TMPL} ${D}${systemd_unitdir}/system/xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service
 }
diff --git a/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-net_%.bbappend b/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-net_%.bbappend
new file mode 100644
index 000000000..33802713d
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-phosphor/ipmi/phosphor-ipmi-net_%.bbappend
@@ -0,0 +1,7 @@
+DEFAULT_RMCPP_IFACE = "eth1"
+
+ALT_RMCPP_IFACE = "eth0"
+SYSTEMD_SERVICE_${PN} += " \
+        ${PN}@${ALT_RMCPP_IFACE}.service \
+        ${PN}@${ALT_RMCPP_IFACE}.socket \
+        "
diff --git a/meta-ampere/meta-jade/recipes-phosphor/packagegroups/packagegroup-obmc-apps.bbappend b/meta-ampere/meta-jade/recipes-phosphor/packagegroups/packagegroup-obmc-apps.bbappend
index f41e5bcd7..ca86a4a21 100644
--- a/meta-ampere/meta-jade/recipes-phosphor/packagegroups/packagegroup-obmc-apps.bbappend
+++ b/meta-ampere/meta-jade/recipes-phosphor/packagegroups/packagegroup-obmc-apps.bbappend
@@ -1,2 +1,6 @@
-RDEPENDS_${PN}-extras_append_mtjade = " webui-vue phosphor-image-signing"
+RDEPENDS_${PN}-extras_append_mtjade = " webui-vue phosphor-image-signing phosphor-virtual-sensor"
 RDEPENDS_${PN}-inventory_append_mtjade = " fault-monitor id-button psu-hotswap-reset"
+
+RDEPENDS_${PN}-inventory_append_mtjade = " \
+                                        host-gpio-handling \
+                                        "
diff --git a/meta-ampere/meta-jade/recipes-phosphor/sensors/phosphor-virtual-sensor/virtual_sensor_config.json b/meta-ampere/meta-jade/recipes-phosphor/sensors/phosphor-virtual-sensor/virtual_sensor_config.json
new file mode 100644
index 000000000..d0dc76782
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-phosphor/sensors/phosphor-virtual-sensor/virtual_sensor_config.json
@@ -0,0 +1,36 @@
+[
+    {
+        "Desc":
+        {
+            "Name": "total_power",
+            "SensorType": "power"
+        },
+        "Threshold" :
+        {
+        },
+        "Params":
+        {
+            "DbusParam":
+            [
+                {
+                    "ParamName": "PSU0_POUTPUT",
+                    "Desc":
+                    {
+                        "Name": "PSU0_POUTPUT",
+                        "SensorType": "power"
+                    }
+                },
+                {
+                    "ParamName": "PSU1_POUTPUT",
+                    "Desc":
+                    {
+                        "Name": "PSU1_POUTPUT",
+                        "SensorType": "power"
+                    }
+                }
+            ]
+        },
+        "Expression": "PSU0_POUTPUT + PSU1_POUTPUT"
+    }
+]
+
diff --git a/meta-ampere/meta-jade/recipes-phosphor/sensors/phosphor-virtual-sensor_%.bbappend b/meta-ampere/meta-jade/recipes-phosphor/sensors/phosphor-virtual-sensor_%.bbappend
new file mode 100644
index 000000000..3c68ff533
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-phosphor/sensors/phosphor-virtual-sensor_%.bbappend
@@ -0,0 +1,10 @@
+FILESEXTRAPATHS_prepend := "${THISDIR}/${PN}:"
+
+SRC_URI_append_mtjade += " \
+            file://virtual_sensor_config.json \
+           "
+
+do_install_append_mtjade() {
+    install -m 0644 ${WORKDIR}/virtual_sensor_config.json ${D}${datadir}/phosphor-virtual-sensor/
+}
+
diff --git a/meta-ampere/meta-jade/recipes-phosphor/watchdog/phosphor-watchdog_%.bbappend b/meta-ampere/meta-jade/recipes-phosphor/watchdog/phosphor-watchdog_%.bbappend
new file mode 100644
index 000000000..0d17c372a
--- /dev/null
+++ b/meta-ampere/meta-jade/recipes-phosphor/watchdog/phosphor-watchdog_%.bbappend
@@ -0,0 +1,9 @@
+FILESEXTRAPATHS_append_mtjade := "${THISDIR}/${PN}:"
+
+#
+# Ampere Mt. Jade power control involves different action during
+# the course of action which does not involve rebooting the Host.
+# Thus disable the use of Host Power-On watchdog.
+#
+WATCHDOG_FMT = ""
+ENABLE_WATCHDOG_FMT = ""