diff options
Diffstat (limited to 'meta-quanta')
-rw-r--r-- | meta-quanta/meta-gsj/recipes-gsj/quanta-nvme-powerctrl/README.md | 48 |
1 files changed, 22 insertions, 26 deletions
diff --git a/meta-quanta/meta-gsj/recipes-gsj/quanta-nvme-powerctrl/README.md b/meta-quanta/meta-gsj/recipes-gsj/quanta-nvme-powerctrl/README.md index 51a9e8fe5..63b52d746 100644 --- a/meta-quanta/meta-gsj/recipes-gsj/quanta-nvme-powerctrl/README.md +++ b/meta-quanta/meta-gsj/recipes-gsj/quanta-nvme-powerctrl/README.md @@ -1,50 +1,46 @@ ### NVME SSD Power Control Manager #### Description - The Package is Mantain for SSD power control and related noification handle Deamon + The package mantains for SSD power control and related noification handle Deamon #### Design - nvme_gpio.service for initinal related GPIOs ( PRESENT, PWR, PWRGD, RST_U2 ) and according PRESENT signal fix HW PWR default output signal. - nvme_powermanager.service loop for monitor PRESENT signal and update PWR output. + The service power supply design follow PCI Express Card Electromechanical Specification Revision 3.0 in Section 2.2 + + nvme_gpio.service follow section 2.2.1 Initial power-Up to initinal and adjust related signal. + + nvme_powermanager.service follow section 2.2.2 power management states monitor PRESENT signal and update related signal. #### Process - * Plugging - 1. U2_[SSD_index]PRSNT_N will be input low + * Plugging + 1. U2_[SSD_index] PRSNT_N will be input low 2. Set PWR_U2_[SSD_index]_EN to high 3. Check PWRGD_U2_[SSD_index] is high 4-1. If PWRGD_U2_[SSD_index] is high (PWR Good) - Wait 5ms - Enable PCI Clock by SMBus 9FGL0851 - Wait 100ms - - Reset RST_BMC_U2 [low->high] - - Send Assert to tell package could read SSD status. + - Set RST_BMC_U2 to high 4-2. If PWRGD_U2_[SSD_index] is low (PWR Fail) - - Disable Clock by SMBus - - Wait 100ms - Set RST_BMC_U2_[SSD_index]_R_N to low - - Set LED_U2_FAULT to high + - Wait 100ms + - Disable PCI Clock by SMBus * Removing - 1. U2_[SSD_index]PRSNT_N will be input high - 2. Disable Clock by SMBus 9FGL0851 - 3. PWR_U2_[SSD_index]_EN to low - 4. Check PWRGD_U2_[SSD_index] is low - 5. Send Assert to tell package update SSD status. - - -#### TODO - - 1. After power on ssd, bmc send command to 9FGL0851 (on SMBus8 0x68) for enable PCI clock, and send RST_BMC_U2 pin rsing event (set low, wait 500ms, set high). The Host could rescan PCI and detect SSD device. + 1. U2_[SSD_index] PRSNT_N will be input high + 2. Set RST_BMC_U2 to low + 3. Wait 100ms + 4. Disable PCI Clock by SMBus + 5. Wait 5ms + 6. PWR_U2_[SSD_index]_EN to low #### Test - 1. PRESENT detect SSD: The Default Hardware is implement. - 2. Initial SSD slot Power output: nvme_gpio service has test on Module. It could sucess initial gpios and setting correct power output. - 3. Detect PRESENT and change power setting: nvme_powermanager service has tested on Module. It could success detect SSD plugged or removal change PWR output. - 4. NVME-MI connect: Ensure SSD power is ready then it will notify quanta NVME-MI package could read SSD information. - 5. FAULT LED handle: When detect power output irregular by PWRGD pin, the service will trigger related FAULT LED. - + 1. PRESENT detect SSD: The hardware design has been implemented. + 2. Initial SSD slot Power output: nvme_gpio service has tested on Module. It could sucess initial gpios and set correct power output. + 3. Detect PRESENT and change power setting: nvme_powermanager service has tested on Module. It could success detect SSD plugged or removal change power output. + 4. Improve initial power-up sequence: For matched hardware default initial power-up setting, the nvme_gpio service only set unplugged slot related signal. + 5. Improve service execute sequence: nvme_powermanager.service must wait for nvme_gpio.service ensure gpio export complete. |