Age | Commit message (Collapse) | Author | Files | Lines |
|
It checks GPIO key for powersupply presence, and creates
the inventory object.
Tested:
1. Plug the PSU, check busctl command for Present attribute
2. Plug out the PSU, check busctl command for Present attribute
$ busctl --no-pager introspect xyz.openbmc_project.Inventory.Manager
/xyz/openbmc_project/inventory/system/chassis/motherboard/powersupply0
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Change-Id: I4520d537d425249debe5c0d8c6bf8b0f6e3c5b34
|
|
Support to get BMC MAC address from FRU over the FRU inventory
information (/xyz/openbmc_project/inventory/system/chassis/motherboard)
and update to the eth0 Ethernet interface and set the eth1addr u-boot
variable.
Tested:
1. Boot to u-boot, clear the eth1addr variable, save and reboot.
2. Boot to Linux:
- Check if the eth0 interface uses the MAC address in FRU.
root@mtjade:~# ip addr show dev eth0
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
link/ether 70:e2:84:86:76:ba brd ff:ff:ff:ff:ff:ff
- Check if the eth1addr u-boot variable uses the MAC address in FRU
root@mtjade:~# fw_printenv eth1addr
eth1addr=70:E2:84:86:76:BA
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: Ifb7eefbb17257545d026005f859d37ef562289b7
|
|
Enable system event log for Redfish. It includes the setting to:
- Enable sel-logger module which logs the sensor event into the
systemd log.
- Enable the rsyslog (intel module) to sync the sensor events from
systemd to /var/log/redfish. The file will be used by Redfish.
- Configure the backend and redfish to get the system log from the
/var/log/redfish instead of system d-bus
- Enable Redfish journal log
Tested: Verify event logs appear in:
1. Redfish: /redfish/v1/Systems/system/LogServices/EventLog/Entries
2. Redfish: /redfish/v1/Managers/bmc/LogServices/Journal/Entries
3. WebUI: /server-health/sys-log at Event type.
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: I3753e2932ec1dc83cdbe0708173531930df65254
|
|
Enable flash_bios feature and configure to use backend script to flash
UEFI firmware via Redfish, WebUI and Rest.
Tested:
1. Flash UEFI firmware via WebUI.
2. Flash UEFI firmware via Redfish UpdateService
3. Flash UEFI firmware via Rest interface.
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: I772e6a409414e374ed01e72e3c69985d0b413cb5
|
|
Implement systemd service to create an Ethernet over USB interface
for communication between CPU and BMC.
Tested:
1. Check usb0 ethernet interface in BMC console
root@mtjade:~# ifconfig usb0
usb0 Link encap:Ethernet HWaddr DA:F7:E9:A3:5A:0C
inet addr:192.168.0.10 Bcast:192.168.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:412 (412.0 B)
2. Check USB Ethernet device on Host Linux
$ lsusb | grep Ethernet
Bus 001 Device 004: ID 1d6b:0103 Linux Foundation NCM (Ethernet) Gadget
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: Icb7c096df426233e8f2ee7318f2a1805f07ab3a7
|
|
Implement the Ampere power control requirements for Altra system.
Tested:
- Check the ipmi commands: ipmi power on/off/soft/reset/cycle
- Check the redfish commands: On, Off, ForceOn, ForceOff,
GracefulShutdown, GracefulRestart, ForceRestart, PowerCycle
Signed-off-by: Tung Nguyen <tungnguyen@os.amperecomputing.com>
Change-Id: Id0c64c1284a6338ce47ca720d0ef75e99d21aa3c
|