| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Upstream bbclasses changed to typically use the `:${PN}` override
syntax, including the SYSTEMD_ variables. Change our systemd.bbclass
to do the same for consistency and perform a tree-wide variable
replacement.
Spot checked by building bletchley and witherspoon and checking
some of the SYSTEMD_LINK directives on installed packages under qemu.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Change-Id: I20a9dd809bff8af8759488734f80486c7228c6eb
|
|
Make the following changes to fix compilation errors:
1. Add honister to LAYERSERIES_COMPAT
2. Increase CONF_VERSION to 2.
3. Fix mistake on previous change on Yocto syntax update.
Tested:
1. Compile OpenBMC for Mt.Jade without error.
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: I5ac3f568d776109955759fab78844b1d38a51af1
|
|
Run convert-overrides.py meta-ampere and update missing changes as
below:
- Change all _mtjade to :mtjade
- Change all _${PN} to :${PN}
Tested:
1. Check compilation without problem.
2. Check basic functions like switch UART mux, power control.
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: I42038b2a98ed1951d6c770bdf49f5fc440f8163e
|
|
When phosphor-state-manager handles the power action to turn on the
host, phosphor-state-manager does not use the software interfaces to
verify the host state. It set the host state to running after all of
required services of the power action target are done. The power on
watchdog is used to verify the host state and handle the failure in
the host state changing. But Mt.Jade platforms do not handle power on
watchdog. This causes the CurrentHostState dbus property is Running
before the host is ready.
In Mt.Jade platform, the SCP drives S0_FW_BOOT_OK to high when the
host is already on. This GPIO can be used to identify the host state.
One service should be added to the required list. This service checks
the host state in power on and triggers obmc-host-quiesce@%i.target
when the host is failed to boot. ampere-host-check package adds
ampere-host-on-host-check@.service for that purpose.
Tested:
1. Boot up BMC with the host is off/on. Check CurrentHostState.
2. Call Ipmitool power off/on. Check the CurrentHostState.
3. Call Ipmitool chassis power off/on. Check the CurrentHostState.
4. Call Ipmitool power cycle. Check the CurrentHostState.
5. Call Ipmitool chassis power cycle. Check the CurrentHostState.
6. Power off the host. Set power policty to Always-on. AC power.
The host should be on. And CurrentHostState should be Running.
7. Power on the host. Set power policty to Always-off. AC power.
The host should be off. And CurrentHostState should be Off.
Change-Id: I9b0b346883a5f0203bf078453065c18ae4603311
Signed-off-by: ThuBaNguyen <thu@os.amperecomputing.com>
|
|
ampere-hostctrl package includes the generic codes and the platform
specific codes. The generic sources are applied for all of the Ampere
platforms, they are the service files and the scripts to setting the
GPIO pins. The platform specific sources are the GPIO pin config file
and the gpio monitor config files.
This commit moves the platform specific files to the platform code.
Tested:
1. Do the power control actions use ipmitool, BMC web and Redfish.
2. Make sure the server states are changed as expected.
Signed-off-by: ThuBaNguyen <thu@os.amperecomputing.com>
Change-Id: Ic0e261109f7a5dfaf38c883bff0afedab763a0b6
|
|
Refactor the Mt.Jade Host power control operations to support Altra
CPU following the Altra SoC BMC Interface specification which still
satisfying the OpenBMC power control framework.
Tested: check the below cases and ensure Host state report correctly:
1. Run "reboot" from Host Linux. Check the Host is graceful
shutdown, then SYS_RESET is asserted and the Host is booted.
2. Run "shutdown" from Host Linux. Check the Host is graceful
shutdown then the chassis power is turned OFF.
3. Run "ipmitool chassis power soft". Check the Host is graceful
shutdown
4. Execute Redfish GracefulShutdown. Check the Host is graceful
shutdown then the chassis power is turned OFF.
5. Execute Redfish GracefulRestart. Check the Host is graceful
shutdown then turned ON.
6. Check other IPMI chassis power and Redfish Reset actions work.
Signed-off-by: ThuBaNguyen <thu@os.amperecomputing.com>
Change-Id: I3a9716f37d7e80bdc1a1d0422e561c8fc51ad040
|
|
The current ampere-hostctl package removes the power off/on services
of phosphor-state-manager and uses Ampere services. This solution is
not correct. Ampere platform should use power control functions of
phosphor-state-manager. And only appends or overides the default
services by Ampere's services if need.
By default, to handle power soft action, phosphor-state-manager will
trigger obmc-host-shutdown@0.target. This target then call
xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service to request OS
shutdown. When the host OS shutdown is already done, the target will
trigger obmc-chassis-poweroff@0.target to turn off the chassis. The
default xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service uses
Ipmi inband to communicate with the host. It is different with Ampere
Mt.Jade platform. We use the GPIO pin SHD_REQ to request shutdown the
host OS. The host will trigger SHD_ACK when shutdown is done. So
*.Ipmi.Internal.SoftPowerOff.service will be overide by Ampere service
named ampere.*.Ipmi.Internal.SoftPowerOff.service. This service will
trigger SHD_REQ pin and wait for SHD_ACK before start
obmc-chassis-poweroff@0.target.
This commit removes ampere-chassis-poweroff, ampere-host-shutdown
serives which handle power off/soft actions and restore
phosphor-state-manager's services. It also supports
ampere.xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service which
will overide xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service.
Tested:
1. Create "power soft" actions use ipmitool, redfish and BMC web.
2. Make sure the power order will be shutdown the host then power
of the chassis.
3. Create "power off" actions use ipmitool, redfish and BMC web.
4. Make sure the power action will be power off the chassis.
Signed-off-by: ThuBaNguyen <thu@os.amperecomputing.com>
Change-Id: Ibc0dc8c62408e8282520c9b70e41ab75c10137f6
|
|
It checks GPIO key for powersupply presence, and creates
the inventory object.
Tested:
1. Plug the PSU, check busctl command for Present attribute
2. Plug out the PSU, check busctl command for Present attribute
$ busctl --no-pager introspect xyz.openbmc_project.Inventory.Manager
/xyz/openbmc_project/inventory/system/chassis/motherboard/powersupply0
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Change-Id: I4520d537d425249debe5c0d8c6bf8b0f6e3c5b34
|
|
Support to get BMC MAC address from FRU over the FRU inventory
information (/xyz/openbmc_project/inventory/system/chassis/motherboard)
and update to the eth0 Ethernet interface and set the eth1addr u-boot
variable.
Tested:
1. Boot to u-boot, clear the eth1addr variable, save and reboot.
2. Boot to Linux:
- Check if the eth0 interface uses the MAC address in FRU.
root@mtjade:~# ip addr show dev eth0
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
link/ether 70:e2:84:86:76:ba brd ff:ff:ff:ff:ff:ff
- Check if the eth1addr u-boot variable uses the MAC address in FRU
root@mtjade:~# fw_printenv eth1addr
eth1addr=70:E2:84:86:76:BA
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: Ifb7eefbb17257545d026005f859d37ef562289b7
|
|
Enable system event log for Redfish. It includes the setting to:
- Enable sel-logger module which logs the sensor event into the
systemd log.
- Enable the rsyslog (intel module) to sync the sensor events from
systemd to /var/log/redfish. The file will be used by Redfish.
- Configure the backend and redfish to get the system log from the
/var/log/redfish instead of system d-bus
- Enable Redfish journal log
Tested: Verify event logs appear in:
1. Redfish: /redfish/v1/Systems/system/LogServices/EventLog/Entries
2. Redfish: /redfish/v1/Managers/bmc/LogServices/Journal/Entries
3. WebUI: /server-health/sys-log at Event type.
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: I3753e2932ec1dc83cdbe0708173531930df65254
|
|
Enable flash_bios feature and configure to use backend script to flash
UEFI firmware via Redfish, WebUI and Rest.
Tested:
1. Flash UEFI firmware via WebUI.
2. Flash UEFI firmware via Redfish UpdateService
3. Flash UEFI firmware via Rest interface.
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: I772e6a409414e374ed01e72e3c69985d0b413cb5
|
|
Implement systemd service to create an Ethernet over USB interface
for communication between CPU and BMC.
Tested:
1. Check usb0 ethernet interface in BMC console
root@mtjade:~# ifconfig usb0
usb0 Link encap:Ethernet HWaddr DA:F7:E9:A3:5A:0C
inet addr:192.168.0.10 Bcast:192.168.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:412 (412.0 B)
2. Check USB Ethernet device on Host Linux
$ lsusb | grep Ethernet
Bus 001 Device 004: ID 1d6b:0103 Linux Foundation NCM (Ethernet) Gadget
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: Icb7c096df426233e8f2ee7318f2a1805f07ab3a7
|
|
Implement the Ampere power control requirements for Altra system.
Tested:
- Check the ipmi commands: ipmi power on/off/soft/reset/cycle
- Check the redfish commands: On, Off, ForceOn, ForceOff,
GracefulShutdown, GracefulRestart, ForceRestart, PowerCycle
Signed-off-by: Tung Nguyen <tungnguyen@os.amperecomputing.com>
Change-Id: Id0c64c1284a6338ce47ca720d0ef75e99d21aa3c
|
