| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The current ampere-hostctl package removes the power off/on services
of phosphor-state-manager and uses Ampere services. This solution is
not correct. Ampere platform should use power control functions of
phosphor-state-manager. And only appends or overides the default
services by Ampere's services if need.
By default, to handle power soft action, phosphor-state-manager will
trigger obmc-host-shutdown@0.target. This target then call
xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service to request OS
shutdown. When the host OS shutdown is already done, the target will
trigger obmc-chassis-poweroff@0.target to turn off the chassis. The
default xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service uses
Ipmi inband to communicate with the host. It is different with Ampere
Mt.Jade platform. We use the GPIO pin SHD_REQ to request shutdown the
host OS. The host will trigger SHD_ACK when shutdown is done. So
*.Ipmi.Internal.SoftPowerOff.service will be overide by Ampere service
named ampere.*.Ipmi.Internal.SoftPowerOff.service. This service will
trigger SHD_REQ pin and wait for SHD_ACK before start
obmc-chassis-poweroff@0.target.
This commit removes ampere-chassis-poweroff, ampere-host-shutdown
serives which handle power off/soft actions and restore
phosphor-state-manager's services. It also supports
ampere.xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service which
will overide xyz.openbmc_project.Ipmi.Internal.SoftPowerOff.service.
Tested:
1. Create "power soft" actions use ipmitool, redfish and BMC web.
2. Make sure the power order will be shutdown the host then power
of the chassis.
3. Create "power off" actions use ipmitool, redfish and BMC web.
4. Make sure the power action will be power off the chassis.
Signed-off-by: ThuBaNguyen <thu@os.amperecomputing.com>
Change-Id: Ibc0dc8c62408e8282520c9b70e41ab75c10137f6
|
|
This makes it possible for us to change out build specific settings.
Change-Id: I862366d8efa97c4c3181b842662bf28dd5bec270
Signed-off-by: William A. Kennington III <wak@google.com>
|
|
The SpeedMbds of ethernet interface is implemented in getInterfaceInfo()
from the phosphor-networkd repo. It is disabled by NIC_SUPPORTS_ETHTOOL
conditional compilation. The default compile mode is to omit the
getInterfaceInfo() which causes the SpeedMbps not set.
This commit supports enable the NIC_SUPPORTS_ETHTOOL to report correct
speed.
Tested:
1.Get SpeedMbps via rest:
$ curl -XGET --user root:0penBmc -H "Content-Type: application/json" \
-H "If-match: *" --insecure \
https://10.38.14.2/redfish/v1/Managers/bmc/EthernetInterfaces/eth1 \
grep | "SpeedMbps"
2.Get speed of eth1 interface on BMC console
$ cat /sys/class/net/eth1/speed
The value getting from openbmc#1 and openbmc#2 match together.
Signed-off-by: Hieu Huynh <hieuh@os.amperecomputing.com>
Change-Id: I57047151fc4eea08c857b95c0770d89ba95f9bc7
|
|
It checks GPIO key for powersupply presence, and creates
the inventory object.
Tested:
1. Plug the PSU, check busctl command for Present attribute
2. Plug out the PSU, check busctl command for Present attribute
$ busctl --no-pager introspect xyz.openbmc_project.Inventory.Manager
/xyz/openbmc_project/inventory/system/chassis/motherboard/powersupply0
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Change-Id: I4520d537d425249debe5c0d8c6bf8b0f6e3c5b34
|
|
Support to get BMC MAC address from FRU over the FRU inventory
information (/xyz/openbmc_project/inventory/system/chassis/motherboard)
and update to the eth0 Ethernet interface and set the eth1addr u-boot
variable.
Tested:
1. Boot to u-boot, clear the eth1addr variable, save and reboot.
2. Boot to Linux:
- Check if the eth0 interface uses the MAC address in FRU.
root@mtjade:~# ip addr show dev eth0
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
link/ether 70:e2:84:86:76:ba brd ff:ff:ff:ff:ff:ff
- Check if the eth1addr u-boot variable uses the MAC address in FRU
root@mtjade:~# fw_printenv eth1addr
eth1addr=70:E2:84:86:76:BA
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: Ifb7eefbb17257545d026005f859d37ef562289b7
|
|
Enable system event log for Redfish. It includes the setting to:
- Enable sel-logger module which logs the sensor event into the
systemd log.
- Enable the rsyslog (intel module) to sync the sensor events from
systemd to /var/log/redfish. The file will be used by Redfish.
- Configure the backend and redfish to get the system log from the
/var/log/redfish instead of system d-bus
- Enable Redfish journal log
Tested: Verify event logs appear in:
1. Redfish: /redfish/v1/Systems/system/LogServices/EventLog/Entries
2. Redfish: /redfish/v1/Managers/bmc/LogServices/Journal/Entries
3. WebUI: /server-health/sys-log at Event type.
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: I3753e2932ec1dc83cdbe0708173531930df65254
|
|
Enable flash_bios feature and configure to use backend script to flash
UEFI firmware via Redfish, WebUI and Rest.
Tested:
1. Flash UEFI firmware via WebUI.
2. Flash UEFI firmware via Redfish UpdateService
3. Flash UEFI firmware via Rest interface.
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: I772e6a409414e374ed01e72e3c69985d0b413cb5
|
|
Implement systemd service to create an Ethernet over USB interface
for communication between CPU and BMC.
Tested:
1. Check usb0 ethernet interface in BMC console
root@mtjade:~# ifconfig usb0
usb0 Link encap:Ethernet HWaddr DA:F7:E9:A3:5A:0C
inet addr:192.168.0.10 Bcast:192.168.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:412 (412.0 B)
2. Check USB Ethernet device on Host Linux
$ lsusb | grep Ethernet
Bus 001 Device 004: ID 1d6b:0103 Linux Foundation NCM (Ethernet) Gadget
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: Icb7c096df426233e8f2ee7318f2a1805f07ab3a7
|
|
Implement the Ampere power control requirements for Altra system.
Tested:
- Check the ipmi commands: ipmi power on/off/soft/reset/cycle
- Check the redfish commands: On, Off, ForceOn, ForceOff,
GracefulShutdown, GracefulRestart, ForceRestart, PowerCycle
Signed-off-by: Tung Nguyen <tungnguyen@os.amperecomputing.com>
Change-Id: Id0c64c1284a6338ce47ca720d0ef75e99d21aa3c
|
