| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Upstream bbclasses changed to typically use the `:${PN}` override
syntax, including the SYSTEMD_ variables. Change our systemd.bbclass
to do the same for consistency and perform a tree-wide variable
replacement.
Spot checked by building bletchley and witherspoon and checking
some of the SYSTEMD_LINK directives on installed packages under qemu.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Change-Id: I20a9dd809bff8af8759488734f80486c7228c6eb
|
|
Make the following changes to fix compilation errors:
1. Add honister to LAYERSERIES_COMPAT
2. Increase CONF_VERSION to 2.
3. Fix mistake on previous change on Yocto syntax update.
Tested:
1. Compile OpenBMC for Mt.Jade without error.
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: I5ac3f568d776109955759fab78844b1d38a51af1
|
|
Run convert-overrides.py meta-ampere and update missing changes as
below:
- Change all _mtjade to :mtjade
- Change all _${PN} to :${PN}
Tested:
1. Check compilation without problem.
2. Check basic functions like switch UART mux, power control.
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Change-Id: I42038b2a98ed1951d6c770bdf49f5fc440f8163e
|
|
The OCP module in Mt.Jade platform supports the GPIO pins to set the
power state. The SPI0 module also supports the GPIO pins to config SPI
mode. These gpio pins have to be set to the right states before power
off/on. The mtjade-gpio-config package will support that.
Tested:
1. Power off/on the host.
2. The OCP and SPI0 gpio pins should be in the corrected states.
Signed-off-by: ThuBaNguyen <thu@os.amperecomputing.com>
Change-Id: I46bca50222b0428f73aa9c05003f650f6ec0cc0b
|
|
The power functions are failed to work. There is one mistake in
merging ampere_power_utils.sh script. This commit fixes the mistake.
Tested:
1. Power off the host when it is on.
2. The host state should be changed to off.
Signed-off-by: ThuBaNguyen <thu@os.amperecomputing.com>
Change-Id: Iaa253e4b8d0f645a2b7097501e8c602d693cb37a
|
|
When phosphor-state-manager handles the power action to turn on the
host, phosphor-state-manager does not use the software interfaces to
verify the host state. It set the host state to running after all of
required services of the power action target are done. The power on
watchdog is used to verify the host state and handle the failure in
the host state changing. But Mt.Jade platforms do not handle power on
watchdog. This causes the CurrentHostState dbus property is Running
before the host is ready.
In Mt.Jade platform, the SCP drives S0_FW_BOOT_OK to high when the
host is already on. This GPIO can be used to identify the host state.
One service should be added to the required list. This service checks
the host state in power on and triggers obmc-host-quiesce@%i.target
when the host is failed to boot. ampere-host-check package adds
ampere-host-on-host-check@.service for that purpose.
Tested:
1. Boot up BMC with the host is off/on. Check CurrentHostState.
2. Call Ipmitool power off/on. Check the CurrentHostState.
3. Call Ipmitool chassis power off/on. Check the CurrentHostState.
4. Call Ipmitool power cycle. Check the CurrentHostState.
5. Call Ipmitool chassis power cycle. Check the CurrentHostState.
6. Power off the host. Set power policty to Always-on. AC power.
The host should be on. And CurrentHostState should be Running.
7. Power on the host. Set power policty to Always-off. AC power.
The host should be off. And CurrentHostState should be Off.
Change-Id: I9b0b346883a5f0203bf078453065c18ae4603311
Signed-off-by: ThuBaNguyen <thu@os.amperecomputing.com>
|
|
ampere-hostctrl package includes the generic codes and the platform
specific codes. The generic sources are applied for all of the Ampere
platforms, they are the service files and the scripts to setting the
GPIO pins. The platform specific sources are the GPIO pin config file
and the gpio monitor config files.
This commit moves the platform specific files to the platform code.
Tested:
1. Do the power control actions use ipmitool, BMC web and Redfish.
2. Make sure the server states are changed as expected.
Signed-off-by: ThuBaNguyen <thu@os.amperecomputing.com>
Change-Id: Ic0e261109f7a5dfaf38c883bff0afedab763a0b6
|
