diff options
| -rwxr-xr-x | meta-facebook/meta-bletchley/recipes-bletchley/motor-ctrl/files/power-ctrl | 107 |
1 files changed, 92 insertions, 15 deletions
diff --git a/meta-facebook/meta-bletchley/recipes-bletchley/motor-ctrl/files/power-ctrl b/meta-facebook/meta-bletchley/recipes-bletchley/motor-ctrl/files/power-ctrl index 523eb26d4d..b27ca323e0 100755 --- a/meta-facebook/meta-bletchley/recipes-bletchley/motor-ctrl/files/power-ctrl +++ b/meta-facebook/meta-bletchley/recipes-bletchley/motor-ctrl/files/power-ctrl @@ -10,6 +10,46 @@ DELAY_POWER_ON="0.5" DELAY_POWER_OFF="5" POWER_BTN_TIMEOUT_CNT=60 +REV_EVT="EVT" +REV_DVT="DVT" +REV_UNKNOW="UNKNOW" + +DBUS_HOST_ST_ON="xyz.openbmc_project.State.Host.HostState.Running" +DBUS_HOST_ST_OFF="xyz.openbmc_project.State.Host.HostState.Off" + +HOST_ST_UNKNOW="Unknow" +HOST_ST_ON="On" +HOST_ST_OFF="Off" +HOST_AC_ON="AC On" +HOST_AC_OFF="AC Off" + +function get_board_rev() { + local rev_id0 + local rev_id1 + local rev_id2 + local rev_val + + rev_id0=$(get_gpio "REV_ID0") + rev_id1=$(get_gpio "REV_ID1") + rev_id2=$(get_gpio "REV_ID2") + rev_val=$((rev_id0+(rev_id1<<1)+(rev_id2<<2))) + + case $rev_val in + 0) + echo "$REV_EVT" + ;; + 1) + echo "$REV_DVT" + ;; + *) + echo "$REV_UNKNOW" + return 1 + ;; + esac + + return 0 +} + #Switch pull low while it be touched function wait_for_switch() { TARGET_PIN=$1 @@ -153,19 +193,40 @@ function get_ac_status(){ is_output="$(( (~p1_config_reg & 0x80)>>7 ))" if [ "$(( host_pwr & is_output ))" -eq 1 ];then - echo "AC on" + echo "$HOST_AC_ON" else - echo "AC off" + echo "$HOST_AC_OFF" fi } -function get_host_status() +function get_host_status_dbus() +{ + local sled_num=$1 + local object="/xyz/openbmc_project/state/host${sled_num}" + local service="xyz.openbmc_project.State.Host${sled_num}" + local interface="xyz.openbmc_project.State.Host" + local property="CurrentHostState" + local host_state + + host_state=$(busctl get-property "$service" "$object" "$interface" "$property" | cut -d '"' -f2) + + if [ "$host_state" = "$DBUS_HOST_ST_ON" ]; then + echo "$HOST_ST_ON" + elif [ "$host_state" = "$DBUS_HOST_ST_OFF" ]; then + echo "$HOST_ST_OFF" + else + echo "$HOST_ST_UNKNOW" + return 1 + fi + + return 0 +} + +function get_host_status_mdio() { SLED_NUM=$1 MDIO_BUS=0 - HOST_ST_UNKNOW="Unknow" - HOST_ST_ON="On" - HOST_ST_OFF="Off" + declare -a PORT_MAP=(0 3 2 1 7 6 5) # check /dev/mem @@ -209,6 +270,22 @@ function get_host_status() return 0 } +function get_host_status() +{ + local sled_num=$1 + local board_rev + + board_rev=$(get_board_rev) + + if [ "$board_rev" = "$REV_EVT" ]; then + get_host_status_dbus "$sled_num" + else + get_host_status_mdio "$sled_num" + fi + + return $? +} + function create_dev_mem() { CHECK_CNT=0 @@ -232,7 +309,7 @@ function create_dev_mem() } function show_usage(){ - echo "Usage: power-ctrl [sled1 | sled2 | sled3 | sled4 | sled5 | sled6] [on off ac-on ac-off status]" + echo "Usage: power-ctrl [sled1 | sled2 | sled3 | sled4 | sled5 | sled6] [on off ac-on ac-off status dfu]" echo " power-ctrl chassis-cycle" } @@ -272,11 +349,11 @@ if [ "$SLED_PRESENT" != 0 ];then fi if [[ "$ACTION" == "on" ]]; then - if [ "$(get_ac_status "$SLED_NUM")" == "AC on" ];then + if [ "$(get_ac_status "$SLED_NUM")" == "$HOST_AC_ON" ];then host_power_st=$(get_host_status "$SLED_NUM") - if [ "$host_power_st" == "On" ]; then + if [ "$host_power_st" == "$HOST_ST_ON" ]; then echo "${SLED} is already On" - elif [ "$host_power_st" == "Off" ]; then + elif [ "$host_power_st" == "$HOST_ST_OFF" ]; then echo "Power on ${SLED}" trigger_power_button "$SLED_NUM" "$DELAY_POWER_ON" else @@ -288,12 +365,12 @@ if [[ "$ACTION" == "on" ]]; then exit 1 fi elif [[ "$ACTION" == "off" ]];then - if [ "$(get_ac_status "$SLED_NUM")" == "AC on" ];then + if [ "$(get_ac_status "$SLED_NUM")" == "$HOST_AC_ON" ];then host_power_st=$(get_host_status "$SLED_NUM") - if [ "$host_power_st" == "On" ]; then + if [ "$host_power_st" == "$HOST_ST_ON" ]; then echo "Power off ${SLED}" trigger_power_button "$SLED_NUM" "$DELAY_POWER_OFF" - elif [ "$host_power_st" == "Off" ]; then + elif [ "$host_power_st" == "$HOST_ST_OFF" ]; then echo "${SLED} is already Off" else echo "${SLED} power state is $host_power_st" @@ -305,12 +382,12 @@ elif [[ "$ACTION" == "off" ]];then fi elif [[ "$ACTION" == "status" ]];then AC_ST=$(get_ac_status "$SLED_NUM") - if [ "$AC_ST" == "AC on" ]; then + if [ "$AC_ST" == "$HOST_AC_ON" ]; then # check host power status if AC is on get_host_status "$SLED_NUM" || exit 1 else # AC off - echo "$AC_ST" + echo "$HOST_AC_OFF" fi elif [[ "$ACTION" == "ac-on" ]];then set_gpio "power-host${SLED_NUM}" 1 |