| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Modify ACBEL PSU configuration file to read output voltage from sysfs
in2_label and to read the output current from curr2_label.
Testing: Placed the modified config file in
/etc//default/obmc/hwmon/ahb/apb/bus@1e78a000/i2c-bus@200/power-supply@5a.conf
then verified the output voltage and current output shows up on the BMC
sensors web page and redfish.
Change-Id: Iacf1469295b99f6a7363d26983786f9c7ed8826a
Signed-off-by: Faisal Awada <faisal@us.ibm.com>
|
|
Add the power-supply configuration files for the acbel-fsg032 power
supplies used in the Bonnell systems in order to get telemetry data
added to D-Bus via phosphor-hwmon.
Bonnell power supplies on bus 3 at 0x5a and 0x5b
Change-Id: I97a1e1ba57ee1b2da6462b6921f121683498fe87
Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com>
|
|
While the max31785 is at the same I2C bus and address as on Rainier, it
only has two fans so it needs a unique hwmon conf file, which it has
because the name is different in the device tree.
Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Change-Id: Ia2c77e4149f02fe0a9d335cdd0551fb4ddd75108
|
|
Since the accuracy of power supply input power sensors is 1% on IBM's
p10bmc system, add `ACCURACY=1` to the power supply configuration of
p10bmc.
Signed-off-by: George Liu <liuxiwei@inspur.com>
Change-Id: If143a61e44936fbd758d556575c250bc6ea501b2
|
|
A fork of it is maintained but its upstream layer has largely been
unmaintained.
No future products are planned to be based on this layer.
Mihawk is similar to Witherspoon.
Signed-off-by: Myung Bae <myungbae@us.ibm.com>
Change-Id: I82f7d777b78cd126237d51e42f1e11abdf80ae68
|
|
Add the power supply temperature readings to the hwmon configuration and
the Rainier and Everest assocation files.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Change-Id: I00e7fde4a58da553b9374733b22b8608d0c9da41
|
|
Add the power-supply configuration files for the ibm-cffps power
supplies used in the Rainier and Everest systems in order to get
telemetry data added to D-Bus via phosphor-hwmon.
Rainier power supplies on bus 3 at 0x68, 0x69, 0x6a, and 0x6b.
Everest power supplies on bus 3 at 0x68, 0x69, 0x6d, and 0x6b. Older
hardware has power supply at 0x6a instead of 0x6d.
Input voltage, input power, output voltage, and output current.
No critical or warning low values, to avoid logging errors when AC is
pulled, or other fault conditions handled by the PSU monitor. AC loss,
brownout, over-voltage, over-current, and other conditions should be
handled by the PSU monitor application.
No critical/warning high values, for similar doubled up fault logging.
Change-Id: I9f39e41e2dd0a7b77910207322506d8376f98772
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
|
|
There is an upcoming systemd change that doesn't handle what was being
done, which was to delay starting phosphor-hwmon from udev until the
chassis cooling type was on D-Bus.
This commit removes this method and goes down to a single hwmon config
file that only supports the air cooled system, which has 2 more fan
rotors than the water cooled one does.
This change also applies to the similar systems witherspoon-tacoma and
swift.
Resolves openbmc/phosphor-hwmon/#19.
Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Change-Id: Ic4ed46a5bf310fb1fef8704dcafc0376c441f8c4
|
|
The IBM rainier machine name is being replaced with the generic p10bmc.
Change-Id: I43d08c3be45d8cc8b03914b9bc257df2668e9fe0
Signed-off-by: Adriana Kobylak <anoo@us.ibm.com>
|
|
Everest has the max31785 at a different i2c address that is behind a
mux, so install its hwmon config at that associated location.
Tested:
Hwmon instance for the max31785 starts successfully on Everest
(From meta-ibm rev: cd84eb53a79edcabddd5e7720f9e0389f4e96151)
Signed-off-by: Matthew Barth <msbarth@us.ibm.com>
Change-Id: Ide9ca8bd76d708ef9453dc7d02526dfbb1dd8a30
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
|
|
Add the max31785 fan controller device to hwmon.
(From meta-ibm rev: 71404ba4966e32bb4ed9a120062d669ed642d851)
Change-Id: I4b2cd1c5379e76ccf40f52dc6ceca6a98f931f40
Signed-off-by: Matthew Barth <msbarth@us.ibm.com>
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
|
|
Mihawk cannot read the 250 soc sensor on the riser, this is because dts
defines pca9545riser@70 instead of pca9545@70.
(From meta-ibm rev: 731297ebde0eb4272d39260a30cd5f5b1f4e6f1a)
Change-Id: Ibcb72ef6be7c953cc35cc216e8cc45e283949e61
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
|
|
Mihawk can use up to eight 250-soc.
Tested:
The user can see the temperature when using 250-soc.
(From meta-ibm rev: 74b7557b08ed2582861cd7da390d84371ec2ff86)
Change-Id: I17b0d969d0902f6470287c6164f542ad84412f7d
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
|
|
The metadata common to all IBM systems is confusingly split between
meta-ibm and meta-witherspoon. Move everything to meta-ibm.
The meta-ibm README is re-written to more accurately reflect the scope
of the layer.
Allow the configuration samples (bblayers.conf.sample,
local.conf.sample) to be sourced from either meta-ibm or
meta-witherspoon until such a time that any workflows and tooling have
had the opportunity to move to meta-ibm.
(From meta-ibm rev: 6e05ef2e90b214eaf4e43ee7027bbbb1d8d09442)
Change-Id: I3ec890d5300f9649c974ea6b9dca93a2e8a889ab
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
|
