Merge tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "As usual, there are lots of minor driver changes across SoC platforms
  from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
  These usually add support for additional chip variations in existing
  drivers, but also add features or bugfixes.

  The SCMI firmware subsystem gains a unified raw userspace interface
  through debugfs, which can be used for validation purposes.

  Newly added drivers include:

   - New power management drivers for StarFive JH7110, Allwinner D1 and
     Renesas RZ/V2M

   - A driver for Qualcomm battery and power supply status

   - A SoC device driver for identifying Nuvoton WPCM450 chips

   - A regulator coupler driver for Mediatek MT81xxv"

* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
  power: supply: Introduce Qualcomm PMIC GLINK power supply
  soc: apple: rtkit: Do not copy the reg state structure to the stack
  soc: sunxi: SUN20I_PPU should depend on PM
  memory: renesas-rpc-if: Remove redundant division of dummy
  soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
  dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
  dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
  firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
  MAINTAINERS: Update qcom CPR maintainer entry
  dt-bindings: firmware: document Qualcomm SM8550 SCM
  dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
  soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
  dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
  soc: qcom: socinfo: Add support for new field in revision 17
  soc: qcom: smd-rpm: Add IPQ9574 compatible
  soc: qcom: pmic_glink: remove redundant calculation of svid
  soc: qcom: stats: Populate all subsystem debugfs files
  dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
  soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
  soc: qcom: pmic_glink: Introduce altmode support
  ...

1 files changed, 127 insertions, 0 deletions

diff --git a/Documentation/ABI/testing/debugfs-driver-dcc b/Documentation/ABI/testing/debugfs-driver-dcc
new file mode 100644
index 000000000000..27ed5919d21b
--- /dev/null
+++ b/Documentation/ABI/testing/debugfs-driver-dcc
@@ -0,0 +1,127 @@
+What:           /sys/kernel/debug/dcc/.../ready
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This file is used to check the status of the dcc
+		hardware if it's ready to receive user configurations.
+		A 'Y' here indicates dcc is ready.
+
+What:           /sys/kernel/debug/dcc/.../trigger
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This is the debugfs interface for manual software
+		triggers. The trigger can be invoked by writing '1'
+		to the file.
+
+What:           /sys/kernel/debug/dcc/.../config_reset
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This file is used to reset the configuration of
+		a dcc driver to the default configuration. When '1'
+		is written to the file, all the previous addresses
+		stored in the driver gets removed and users need to
+		reconfigure addresses again.
+
+What:           /sys/kernel/debug/dcc/.../[list-number]/config
+Date:		 December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This stores the addresses of the registers which
+		can be read in case of a hardware crash or manual
+		software triggers. The input addresses type
+		can be one of following dcc instructions: read,
+		write, read-write, and loop type. The lists need to
+		be configured sequentially and not in a overlapping
+		manner; e.g. users can jump to list x only after
+		list y is configured and enabled. The input format for
+		each type is as follows:
+
+	        i) Read instruction
+
+		   ::
+
+		     echo R <addr> <n> <bus> >/sys/kernel/debug/dcc/../[list-number]/config
+
+		   where:
+
+		   <addr>
+			The address to be read.
+
+		   <n>
+			The addresses word count, starting from address <1>.
+			Each word is 32 bits (4 bytes). If omitted, defaulted
+			to 1.
+
+		   <bus type>
+			The bus type, which can be either 'apb' or 'ahb'.
+			The default is 'ahb' if leaved out.
+
+		ii) Write instruction
+
+		    ::
+
+		      echo W <addr> <n> <bus type> > /sys/kernel/debug/dcc/../[list-number]/config
+
+		    where:
+
+		    <addr>
+			The address to be written.
+
+		    <n>
+			The value to be written at <addr>.
+
+		    <bus type>
+			The bus type, which can be either 'apb' or 'ahb'.
+
+	        iii) Read-write instruction
+
+		     ::
+
+		       echo RW <addr> <n> <mask> > /sys/kernel/debug/dcc/../[list-number]/config
+
+		     where:
+
+		     <addr>
+			The address to be read and written.
+
+		     <n>
+		        The value to be written at <addr>.
+
+		     <mask>
+			The value mask.
+
+		iv) Loop instruction
+
+		    ::
+
+		      echo L <loop count> <address count> <address>... > /sys/kernel/debug/dcc/../[list-number]/config
+
+		    where:
+
+		    <loop count>
+			Number of iterations
+
+		    <address count>
+			total number of addresses to be written
+
+		    <address>
+			Space-separated list of addresses.
+
+What:           /sys/kernel/debug/dcc/.../[list-number]/enable
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This debugfs interface is used for enabling the
+		the dcc hardware. A file named "enable" is in the
+		directory list number where users can enable/disable
+		the specific list by writing boolean (1 or 0) to the
+		file.
+
+		On enabling the dcc, all the addresses specified
+		by the user for the corresponding list is written
+		into dcc sram which is read by the dcc hardware
+		on manual or crash induced triggers. Lists must
+		be configured and enabled sequentially, e.g. list
+		2 can only be enabled when list 1 have so.