summaryrefslogtreecommitdiff
path: root/Documentation/blockdev
diff options
context:
space:
mode:
authorChristoph Hellwig <hch@lst.de>2017-04-06 14:28:46 +0300
committerJens Axboe <axboe@fb.com>2017-04-14 23:00:49 +0300
commit84253394927c4352652d0b118ad9583f5646959b (patch)
treeb20c655d26e7cc40336c1975bfe6ad28c4f4e8df /Documentation/blockdev
parent3f19cd23f3a9420fe7bd98ad41d05e45fa6d4d47 (diff)
downloadlinux-84253394927c4352652d0b118ad9583f5646959b.tar.xz
remove the mg_disk driver
This drivers was added in 2008, but as far as a I can tell we never had a single platform that actually registered resources for the platform driver. It's also been unmaintained for a long time and apparently has a ATA mode that can be driven using the IDE/libata subsystem. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Diffstat (limited to 'Documentation/blockdev')
-rw-r--r--Documentation/blockdev/mflash.txt84
1 files changed, 0 insertions, 84 deletions
diff --git a/Documentation/blockdev/mflash.txt b/Documentation/blockdev/mflash.txt
deleted file mode 100644
index f7e050551487..000000000000
--- a/Documentation/blockdev/mflash.txt
+++ /dev/null
@@ -1,84 +0,0 @@
-This document describes m[g]flash support in linux.
-
-Contents
- 1. Overview
- 2. Reserved area configuration
- 3. Example of mflash platform driver registration
-
-1. Overview
-
-Mflash and gflash are embedded flash drive. The only difference is mflash is
-MCP(Multi Chip Package) device. These two device operate exactly same way.
-So the rest mflash repersents mflash and gflash altogether.
-
-Internally, mflash has nand flash and other hardware logics and supports
-2 different operation (ATA, IO) modes. ATA mode doesn't need any new
-driver and currently works well under standard IDE subsystem. Actually it's
-one chip SSD. IO mode is ATA-like custom mode for the host that doesn't have
-IDE interface.
-
-Following are brief descriptions about IO mode.
-A. IO mode based on ATA protocol and uses some custom command. (read confirm,
-write confirm)
-B. IO mode uses SRAM bus interface.
-C. IO mode supports 4kB boot area, so host can boot from mflash.
-
-2. Reserved area configuration
-If host boot from mflash, usually needs raw area for boot loader image. All of
-the mflash's block device operation will be taken this value as start offset.
-Note that boot loader's size of reserved area and kernel configuration value
-must be same.
-
-3. Example of mflash platform driver registration
-Working mflash is very straight forward. Adding platform device stuff to board
-configuration file is all. Here is some pseudo example.
-
-static struct mg_drv_data mflash_drv_data = {
- /* If you want to polling driver set to 1 */
- .use_polling = 0,
- /* device attribution */
- .dev_attr = MG_BOOT_DEV
-};
-
-static struct resource mg_mflash_rsc[] = {
- /* Base address of mflash */
- [0] = {
- .start = 0x08000000,
- .end = 0x08000000 + SZ_64K - 1,
- .flags = IORESOURCE_MEM
- },
- /* mflash interrupt pin */
- [1] = {
- .start = IRQ_GPIO(84),
- .end = IRQ_GPIO(84),
- .flags = IORESOURCE_IRQ
- },
- /* mflash reset pin */
- [2] = {
- .start = 43,
- .end = 43,
- .name = MG_RST_PIN,
- .flags = IORESOURCE_IO
- },
- /* mflash reset-out pin
- * If you use mflash as storage device (i.e. other than MG_BOOT_DEV),
- * should assign this */
- [3] = {
- .start = 51,
- .end = 51,
- .name = MG_RSTOUT_PIN,
- .flags = IORESOURCE_IO
- }
-};
-
-static struct platform_device mflash_dev = {
- .name = MG_DEV_NAME,
- .id = -1,
- .dev = {
- .platform_data = &mflash_drv_data,
- },
- .num_resources = ARRAY_SIZE(mg_mflash_rsc),
- .resource = mg_mflash_rsc
-};
-
-platform_device_register(&mflash_dev);