Merge tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "No core changes this time around.

  New drivers:

   - New driver for Renesas R8A779H0 also known as R-Car V4M.

   - New driver for the Awinic AW9523/B I2C GPIO expander. I found this
     living out-of-tree in OpenWrt as an upstream attempt had stalled on
     the finishing line, so I picked it up and finished the job.

  Improvements:

   - The Nomadik pin control driver was for years re-used out of tree
     for the ST STA chips, and now the IP was re-used in a MIPS
     automotive SoC called MobilEyeq5, so it has been split in pin
     control and GPIO drivers so the latter can be reused by MobilEyeq5.
     (Along with a long list of cleanups)

   - A lot of overall cleanup and tidying up"

* tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (87 commits)
  drivers/gpio/nomadik: move dummy nmk_gpio_dbg_show_one() to header
  gpio: nomadik: remove BUG_ON() in nmk_gpio_populate_chip()
  dt-bindings: pinctrl: qcom: update compatible name for match with driver
  pinctrl: aw9523: Make the driver tristate
  pinctrl: nomadik: fix dereference of error pointer
  gpio: nomadik: Back out some managed resources
  pinctrl: aw9523: Add proper terminator
  pinctrl: core: comment that pinctrl_add_gpio_range() is deprecated
  pinctrl: pinmux: Suppress error message for -EPROBE_DEFER
  pinctrl: Add driver for Awinic AW9523/B I2C GPIO Expander
  dt-bindings: pinctrl: Add bindings for Awinic AW9523/AW9523B
  gpio: nomadik: Finish conversion to use firmware node APIs
  gpio: nomadik: fix Kconfig dependencies inbetween pinctrl & GPIO
  pinctrl: da9062: Add OF table
  dt-bindings: pinctrl: at91: add sam9x7
  pinctrl: ocelot: remove redundant assignment to variable ret
  gpio: nomadik: grab optional reset control and deassert it at probe
  gpio: nomadik: support mobileye,eyeq5-gpio
  gpio: nomadik: handle variadic GPIO count
  gpio: nomadik: support shared GPIO IRQs
  ...

2 files changed, 95 insertions, 31 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
deleted file mode 100644
index 8315ac7780ef..000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
+++ /dev/null
@@ -1,31 +0,0 @@
-Nomadik GPIO controller
-
-Required properties:
-- compatible            : Should be "st,nomadik-gpio".
-- reg                   : Physical base address and length of the controller's registers.
-- interrupts            : The interrupt outputs from the controller.
-- #gpio-cells           : Should be two:
-                            The first cell is the pin number.
-                            The second cell is used to specify optional parameters:
-                              - bits[3:0] trigger type and level flags:
-                                  1 = low-to-high edge triggered.
-                                  2 = high-to-low edge triggered.
-                                  4 = active high level-sensitive.
-                                  8 = active low level-sensitive.
-- gpio-controller       : Marks the device node as a GPIO controller.
-- interrupt-controller  : Marks the device node as an interrupt controller.
-- gpio-bank             : Specifies which bank a controller owns.
-- st,supports-sleepmode : Specifies whether controller can sleep or not
-
-Example:
-
-                gpio1: gpio@8012e080 {
-                        compatible = "st,nomadik-gpio";
-                        reg =  <0x8012e080 0x80>;
-                        interrupts = <0 120 0x4>;
-                        #gpio-cells = <2>;
-                        gpio-controller;
-                        interrupt-controller;
-                        st,supports-sleepmode;
-                        gpio-bank = <1>;
-                };
diff --git a/Documentation/devicetree/bindings/gpio/st,nomadik-gpio.yaml b/Documentation/devicetree/bindings/gpio/st,nomadik-gpio.yaml
new file mode 100644
index 000000000000..38d37d8f7201
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/st,nomadik-gpio.yaml
@@ -0,0 +1,95 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/st,nomadik-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Nomadik GPIO controller
+
+description:
+  The Nomadik GPIO driver handles Nomadik SoC GPIO blocks. This block has also
+  been called ST STA2X11. On the Nomadik platform, this driver is intertwined
+  with pinctrl-nomadik.
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+properties:
+  $nodename:
+    pattern: "^gpio@[0-9a-f]+$"
+
+  compatible:
+    enum:
+      - st,nomadik-gpio
+      - mobileye,eyeq5-gpio
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  "#gpio-cells":
+    const: 2
+
+  gpio-controller: true
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+
+  gpio-bank:
+    description: System-wide GPIO bank index.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  st,supports-sleepmode:
+    description: Whether the controller can sleep or not.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  clocks:
+    maxItems: 1
+
+  gpio-ranges:
+    maxItems: 1
+
+  ngpios:
+    minimum: 0
+    maximum: 32
+
+  resets:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#gpio-cells"
+  - gpio-controller
+  - interrupt-controller
+  - gpio-bank
+
+unevaluatedProperties: false
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mobileye,eyeq5-gpio
+    then:
+      properties:
+        st,supports-sleepmode: false
+
+examples:
+  - |
+    gpio@8012e080 {
+        compatible = "st,nomadik-gpio";
+        reg =  <0x8012e080 0x80>;
+        interrupts = <0 120 0x4>;
+        #gpio-cells = <2>;
+        gpio-controller;
+        interrupt-controller;
+        st,supports-sleepmode;
+        gpio-bank = <1>;
+    };