diff options
author | Linus Torvalds <torvalds@linux-foundation.org> | 2020-08-09 22:38:51 +0300 |
---|---|---|
committer | Linus Torvalds <torvalds@linux-foundation.org> | 2020-08-09 22:38:51 +0300 |
commit | dec1fbbc1d7c46aed9fc1d3ee1f7f4fc04d6ed51 (patch) | |
tree | a2d88e9bb259c7866be2129dedf77a828ca8911a /Documentation/devicetree/bindings/memory-controllers | |
parent | 71fa1a4489ff93ac4acd7e6c5b00098ba53a4485 (diff) | |
parent | 6a1380271b75e0d9a961e192e56b733fedf7a23a (diff) | |
download | linux-dec1fbbc1d7c46aed9fc1d3ee1f7f4fc04d6ed51.tar.xz |
Merge tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Spelling
- http to https updates
NAND core changes:
- Drop useless 'depends on' in Kconfig
- Add an extra level in the Kconfig hierarchy
- Trivial spellings
- Dynamic allocation of the interface configurations
- Dropping the default ONFI timing mode
- Various cleanup (types, structures, naming, comments)
- Hide the chip->data_interface indirection
- Add the generic rb-gpios property
- Add the ->choose_interface_config() hook
- Introduce nand_choose_best_sdr_timings()
- Use default values for tPROG_max and tBERS_max
- Avoid redefining tR_max and tCCS_min
- Add a helper to find the closest ONFI mode
- bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
- fsl-upm: Deprecation of specific DT properties
- fsl_upm: Driver rework and cleanup in favor of ->exec_op()
- Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
- brcmnand: ECC error handling on EDU transfers
- brcmnand: Don't default to EDU transfers
- qcom: Set BAM mode only if not set already
- qcom: Avoid write to unavailable register
- gpio: Driver rework in favor of ->exec_op()
- tango: ->exec_op() conversion
- mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
- toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4,
TC58NVG0S3E, and TC58TEG5DCLTA00
- hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
SPI NOR core changes:
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which is
critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts during
the release cycle.
SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was taken
through the SPI tree. Merge it also in spi-nor/next to avoid
conflicts during the release cycle.
- intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't support
it.
- Fix performance regression"
* tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (79 commits)
MTD: pfow.h: drop a duplicated word
MTD: mtd-abi.h: drop a duplicated word
mtd: rawnand: omap_elm: Replace HTTP links with HTTPS ones
mtd: Replace HTTP links with HTTPS ones
mtd: hyperbus: Replace HTTP links with HTTPS ones
mtd: revert "spi-nor: intel: provide a range for poll_timout"
mtd: spi-nor: update read capabilities for w25q64 and s25fl064k
mtd: spi-nor: micron: Add SPI_NOR_DUAL_READ flag on mt25qu02g
mtd: spi-nor: macronix: Add support for mx66u2g45g
mtd: spi-nor: intel-spi: Simulate WRDI command
mtd: spi-nor: Disable the flash quad mode in spi_nor_restore()
mtd: spi-nor: Add capability to disable flash quad mode
mtd: spi-nor: spansion: Remove s70fl01gs from flash_info
mtd: spi-nor: sfdp: do not make invalid quad enable fatal
dt-bindings: mtd: fsl-upm-nand: Deprecate chip-delay and fsl, upm-wait-flags
mtd: rawnand: stm32_fmc2: get resources from parent node
mtd: rawnand: stm32_fmc2: use regmap APIs
memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver
dt-bindings: memory-controller: add STM32 FMC2 EBI controller documentation
dt-bindings: mtd: update STM32 FMC2 NAND controller documentation
...
Diffstat (limited to 'Documentation/devicetree/bindings/memory-controllers')
-rw-r--r-- | Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml | 252 |
1 files changed, 252 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml new file mode 100644 index 000000000000..70eaf739036b --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml @@ -0,0 +1,252 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/st,stm32-fmc2-ebi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics Flexible Memory Controller 2 (FMC2) Bindings + +description: | + The FMC2 functional block makes the interface with: synchronous and + asynchronous static devices (such as PSNOR, PSRAM or other memory-mapped + peripherals) and NAND flash memories. + Its main purposes are: + - to translate AXI transactions into the appropriate external device + protocol + - to meet the access time requirements of the external devices + All external devices share the addresses, data and control signals with the + controller. Each external device is accessed by means of a unique Chip + Select. The FMC2 performs only one access at a time to an external device. + +maintainers: + - Christophe Kerello <christophe.kerello@st.com> + +properties: + compatible: + const: st,stm32mp1-fmc2-ebi + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + "#address-cells": + const: 2 + + "#size-cells": + const: 1 + + ranges: + description: | + Reflects the memory layout with four integer values per bank. Format: + <bank-number> 0 <address of the bank> <size> + +patternProperties: + "^.*@[0-4],[a-f0-9]+$": + type: object + + properties: + reg: + description: Bank number, base address and size of the device. + + st,fmc2-ebi-cs-transaction-type: + description: | + Select one of the transactions type supported + 0: Asynchronous mode 1 SRAM/FRAM. + 1: Asynchronous mode 1 PSRAM. + 2: Asynchronous mode A SRAM/FRAM. + 3: Asynchronous mode A PSRAM. + 4: Asynchronous mode 2 NOR. + 5: Asynchronous mode B NOR. + 6: Asynchronous mode C NOR. + 7: Asynchronous mode D NOR. + 8: Synchronous read synchronous write PSRAM. + 9: Synchronous read asynchronous write PSRAM. + 10: Synchronous read synchronous write NOR. + 11: Synchronous read asynchronous write NOR. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 11 + + st,fmc2-ebi-cs-cclk-enable: + description: Continuous clock enable (first bank must be configured + in synchronous mode). The FMC_CLK is generated continuously + during asynchronous and synchronous access. By default, the + FMC_CLK is only generated during synchronous access. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-mux-enable: + description: Address/Data multiplexed on databus (valid only with + NOR and PSRAM transactions type). By default, Address/Data + are not multiplexed. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-buswidth: + description: Data bus width + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 8, 16 ] + default: 16 + + st,fmc2-ebi-cs-waitpol-high: + description: Wait signal polarity (NWAIT signal active high). + By default, NWAIT is active low. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-waitcfg-enable: + description: The NWAIT signal indicates wheither the data from the + device are valid or if a wait state must be inserted when accessing + the device in synchronous mode. By default, the NWAIT signal is + active one data cycle before wait state. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-wait-enable: + description: The NWAIT signal is enabled (its level is taken into + account after the programmed latency period to insert wait states + if asserted). By default, the NWAIT signal is disabled. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-asyncwait-enable: + description: The NWAIT signal is taken into account during asynchronous + transactions. By default, the NWAIT signal is not taken into account + during asynchronous transactions. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-cpsize: + description: CRAM page size. The controller splits the burst access + when the memory page is reached. By default, no burst split when + crossing page boundary. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 128, 256, 512, 1024 ] + default: 0 + + st,fmc2-ebi-cs-byte-lane-setup-ns: + description: This property configures the byte lane setup timing + defined in nanoseconds from NBLx low to Chip Select NEx low. + + st,fmc2-ebi-cs-address-setup-ns: + description: This property defines the duration of the address setup + phase in nanoseconds used for asynchronous read/write transactions. + + st,fmc2-ebi-cs-address-hold-ns: + description: This property defines the duration of the address hold + phase in nanoseconds used for asynchronous multiplexed read/write + transactions. + + st,fmc2-ebi-cs-data-setup-ns: + description: This property defines the duration of the data setup phase + in nanoseconds used for asynchronous read/write transactions. + + st,fmc2-ebi-cs-bus-turnaround-ns: + description: This property defines the delay in nanoseconds between the + end of current read/write transaction and the next transaction. + + st,fmc2-ebi-cs-data-hold-ns: + description: This property defines the duration of the data hold phase + in nanoseconds used for asynchronous read/write transactions. + + st,fmc2-ebi-cs-clk-period-ns: + description: This property defines the FMC_CLK output signal period in + nanoseconds. + + st,fmc2-ebi-cs-data-latency-ns: + description: This property defines the data latency before reading or + writing the first data in nanoseconds. + + st,fmc2_ebi-cs-write-address-setup-ns: + description: This property defines the duration of the address setup + phase in nanoseconds used for asynchronous write transactions. + + st,fmc2-ebi-cs-write-address-hold-ns: + description: This property defines the duration of the address hold + phase in nanoseconds used for asynchronous multiplexed write + transactions. + + st,fmc2-ebi-cs-write-data-setup-ns: + description: This property defines the duration of the data setup + phase in nanoseconds used for asynchronous write transactions. + + st,fmc2-ebi-cs-write-bus-turnaround-ns: + description: This property defines the delay between the end of current + write transaction and the next transaction in nanoseconds. + + st,fmc2-ebi-cs-write-data-hold-ns: + description: This property defines the duration of the data hold phase + in nanoseconds used for asynchronous write transactions. + + st,fmc2-ebi-cs-max-low-pulse-ns: + description: This property defines the maximum chip select low pulse + duration in nanoseconds for synchronous transactions. When this timing + reaches 0, the controller splits the current access, toggles NE to + allow device refresh and restarts a new access. + + required: + - reg + +required: + - "#address-cells" + - "#size-cells" + - compatible + - reg + - clocks + - ranges + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp1-clks.h> + #include <dt-bindings/reset/stm32mp1-resets.h> + memory-controller@58002000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "st,stm32mp1-fmc2-ebi"; + reg = <0x58002000 0x1000>; + clocks = <&rcc FMC_K>; + resets = <&rcc FMC_R>; + + ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */ + <1 0 0x64000000 0x04000000>, /* EBI CS 2 */ + <2 0 0x68000000 0x04000000>, /* EBI CS 3 */ + <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */ + <4 0 0x80000000 0x10000000>; /* NAND */ + + psram@0,0 { + compatible = "mtd-ram"; + reg = <0 0x00000000 0x100000>; + bank-width = <2>; + + st,fmc2-ebi-cs-transaction-type = <1>; + st,fmc2-ebi-cs-address-setup-ns = <60>; + st,fmc2-ebi-cs-data-setup-ns = <30>; + st,fmc2-ebi-cs-bus-turnaround-ns = <5>; + }; + + nand-controller@4,0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32mp1-fmc2-nfc"; + reg = <4 0x00000000 0x1000>, + <4 0x08010000 0x1000>, + <4 0x08020000 0x1000>, + <4 0x01000000 0x1000>, + <4 0x09010000 0x1000>, + <4 0x09020000 0x1000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>, + <&mdma1 20 0x2 0x12000a08 0x0 0x0>, + <&mdma1 21 0x2 0x12000a0a 0x0 0x0>; + dma-names = "tx", "rx", "ecc"; + + nand@0 { + reg = <0>; + nand-on-flash-bbt; + #address-cells = <1>; + #size-cells = <1>; + }; + }; + }; + +... |