Merge tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "As usual, there are lots of minor driver changes across SoC platforms
  from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
  These usually add support for additional chip variations in existing
  drivers, but also add features or bugfixes.

  The SCMI firmware subsystem gains a unified raw userspace interface
  through debugfs, which can be used for validation purposes.

  Newly added drivers include:

   - New power management drivers for StarFive JH7110, Allwinner D1 and
     Renesas RZ/V2M

   - A driver for Qualcomm battery and power supply status

   - A SoC device driver for identifying Nuvoton WPCM450 chips

   - A regulator coupler driver for Mediatek MT81xxv"

* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
  power: supply: Introduce Qualcomm PMIC GLINK power supply
  soc: apple: rtkit: Do not copy the reg state structure to the stack
  soc: sunxi: SUN20I_PPU should depend on PM
  memory: renesas-rpc-if: Remove redundant division of dummy
  soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
  dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
  dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
  firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
  MAINTAINERS: Update qcom CPR maintainer entry
  dt-bindings: firmware: document Qualcomm SM8550 SCM
  dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
  soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
  dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
  soc: qcom: socinfo: Add support for new field in revision 17
  soc: qcom: smd-rpm: Add IPQ9574 compatible
  soc: qcom: pmic_glink: remove redundant calculation of svid
  soc: qcom: stats: Populate all subsystem debugfs files
  dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
  soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
  soc: qcom: pmic_glink: Introduce altmode support
  ...

30 files changed, 1082 insertions, 398 deletions

diff --git a/Documentation/ABI/testing/debugfs-driver-dcc b/Documentation/ABI/testing/debugfs-driver-dcc
new file mode 100644
index 000000000000..27ed5919d21b
--- /dev/null
+++ b/Documentation/ABI/testing/debugfs-driver-dcc
@@ -0,0 +1,127 @@
+What:           /sys/kernel/debug/dcc/.../ready
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This file is used to check the status of the dcc
+		hardware if it's ready to receive user configurations.
+		A 'Y' here indicates dcc is ready.
+
+What:           /sys/kernel/debug/dcc/.../trigger
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This is the debugfs interface for manual software
+		triggers. The trigger can be invoked by writing '1'
+		to the file.
+
+What:           /sys/kernel/debug/dcc/.../config_reset
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This file is used to reset the configuration of
+		a dcc driver to the default configuration. When '1'
+		is written to the file, all the previous addresses
+		stored in the driver gets removed and users need to
+		reconfigure addresses again.
+
+What:           /sys/kernel/debug/dcc/.../[list-number]/config
+Date:		 December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This stores the addresses of the registers which
+		can be read in case of a hardware crash or manual
+		software triggers. The input addresses type
+		can be one of following dcc instructions: read,
+		write, read-write, and loop type. The lists need to
+		be configured sequentially and not in a overlapping
+		manner; e.g. users can jump to list x only after
+		list y is configured and enabled. The input format for
+		each type is as follows:
+
+	        i) Read instruction
+
+		   ::
+
+		     echo R <addr> <n> <bus> >/sys/kernel/debug/dcc/../[list-number]/config
+
+		   where:
+
+		   <addr>
+			The address to be read.
+
+		   <n>
+			The addresses word count, starting from address <1>.
+			Each word is 32 bits (4 bytes). If omitted, defaulted
+			to 1.
+
+		   <bus type>
+			The bus type, which can be either 'apb' or 'ahb'.
+			The default is 'ahb' if leaved out.
+
+		ii) Write instruction
+
+		    ::
+
+		      echo W <addr> <n> <bus type> > /sys/kernel/debug/dcc/../[list-number]/config
+
+		    where:
+
+		    <addr>
+			The address to be written.
+
+		    <n>
+			The value to be written at <addr>.
+
+		    <bus type>
+			The bus type, which can be either 'apb' or 'ahb'.
+
+	        iii) Read-write instruction
+
+		     ::
+
+		       echo RW <addr> <n> <mask> > /sys/kernel/debug/dcc/../[list-number]/config
+
+		     where:
+
+		     <addr>
+			The address to be read and written.
+
+		     <n>
+		        The value to be written at <addr>.
+
+		     <mask>
+			The value mask.
+
+		iv) Loop instruction
+
+		    ::
+
+		      echo L <loop count> <address count> <address>... > /sys/kernel/debug/dcc/../[list-number]/config
+
+		    where:
+
+		    <loop count>
+			Number of iterations
+
+		    <address count>
+			total number of addresses to be written
+
+		    <address>
+			Space-separated list of addresses.
+
+What:           /sys/kernel/debug/dcc/.../[list-number]/enable
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This debugfs interface is used for enabling the
+		the dcc hardware. A file named "enable" is in the
+		directory list number where users can enable/disable
+		the specific list by writing boolean (1 or 0) to the
+		file.
+
+		On enabling the dcc, all the addresses specified
+		by the user for the corresponding list is written
+		into dcc sram which is read by the dcc hardware
+		on manual or crash induced triggers. Lists must
+		be configured and enabled sequentially, e.g. list
+		2 can only be enabled when list 1 have so.
diff --git a/Documentation/ABI/testing/debugfs-scmi b/Documentation/ABI/testing/debugfs-scmi
new file mode 100644
index 000000000000..ee7179ab2edf
--- /dev/null
+++ b/Documentation/ABI/testing/debugfs-scmi
@@ -0,0 +1,70 @@
+What:		/sys/kernel/debug/scmi/<n>/instance_name
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	The name of the underlying SCMI instance <n> described by
+		all the debugfs accessors rooted at /sys/kernel/debug/scmi/<n>,
+		expressed as the full name of the top DT SCMI node under which
+		this SCMI instance is rooted.
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/atomic_threshold_us
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	An optional time value, expressed in microseconds, representing,
+		on this SCMI instance <n>, the threshold above which any SCMI
+		command, advertised to have an higher-than-threshold execution
+		latency, should not be considered for atomic mode of operation,
+		even if requested.
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/transport/type
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	A string representing the type of transport configured for this
+		SCMI instance <n>.
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/transport/is_atomic
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	A boolean stating if the transport configured on the underlying
+		SCMI instance <n> is capable of atomic mode of operation.
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/transport/max_rx_timeout_ms
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	Timeout in milliseconds allowed for SCMI synchronous replies
+		for the currently configured SCMI transport for instance <n>.
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/transport/max_msg_size
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	Max message size of allowed SCMI messages for the currently
+		configured SCMI transport for instance <n>.
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/transport/tx_max_msg
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	Max number of concurrently allowed in-flight SCMI messages for
+		the currently configured SCMI transport for instance <n> on the
+		TX channels.
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/transport/rx_max_msg
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	Max number of concurrently allowed in-flight SCMI messages for
+		the currently configured SCMI transport for instance <n> on the
+		RX channels.
+Users:		Debugging, any userspace test suite
diff --git a/Documentation/ABI/testing/debugfs-scmi-raw b/Documentation/ABI/testing/debugfs-scmi-raw
new file mode 100644
index 000000000000..97678cc9535c
--- /dev/null
+++ b/Documentation/ABI/testing/debugfs-scmi-raw
@@ -0,0 +1,117 @@
+What:		/sys/kernel/debug/scmi/<n>/raw/message
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	SCMI Raw synchronous message injection/snooping facility; write
+		a complete SCMI synchronous command message (header included)
+		in little-endian binary format to have it sent to the configured
+		backend SCMI server for instance <n>.
+		Any subsequently received response can be read from this same
+		entry if it arrived within the configured timeout.
+		Each write to the entry causes one command request to be built
+		and sent while the replies are read back one message at time
+		(receiving an EOF at each message boundary).
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/raw/message_async
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	SCMI Raw asynchronous message injection/snooping facility; write
+		a complete SCMI asynchronous command message (header included)
+		in little-endian binary format to have it sent to the configured
+		backend SCMI server for instance <n>.
+		Any subsequently received response can be read from this same
+		entry if it arrived within the configured timeout.
+		Any additional delayed response received afterwards can be read
+		from this same entry too if it arrived within the configured
+		timeout.
+		Each write to the entry causes one command request to be built
+		and sent while the replies are read back one message at time
+		(receiving an EOF at each message boundary).
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/raw/errors
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	SCMI Raw message errors facility; any kind of timed-out or
+		generally unexpectedly received SCMI message, for instance <n>,
+		can be read from this entry.
+		Each read gives back one message at time (receiving an EOF at
+		each message boundary).
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/raw/notification
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	SCMI Raw notification snooping facility; any notification
+		emitted by the backend SCMI server, for instance <n>, can be
+		read from this entry.
+		Each read gives back one message at time (receiving an EOF at
+		each message boundary).
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/raw/reset
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	SCMI Raw stack reset facility; writing a value to this entry
+		causes the internal queues of any kind of received message,
+		still pending to be read out for instance <n>, to be immediately
+		flushed.
+		Can be used to reset and clean the SCMI Raw stack between to
+		different test-run.
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/raw/channels/<m>/message
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	SCMI Raw synchronous message injection/snooping facility; write
+		a complete SCMI synchronous command message (header included)
+		in little-endian binary format to have it sent to the configured
+		backend SCMI server for instance <n> through the <m> transport
+		channel.
+		Any subsequently received response can be read from this same
+		entry if it arrived on channel <m> within the configured
+		timeout.
+		Each write to the entry causes one command request to be built
+		and sent while the replies are read back one message at time
+		(receiving an EOF at each message boundary).
+		Channel identifier <m> matches the SCMI protocol number which
+		has been associated with this transport channel in the DT
+		description, with base protocol number 0x10 being the default
+		channel for this instance.
+		Note that these per-channel entries rooted at <..>/channels
+		exist only if the transport is configured to have more than
+		one default channel.
+Users:		Debugging, any userspace test suite
+
+What:		/sys/kernel/debug/scmi/<n>/raw/channels/<m>/message_async
+Date:		March 2023
+KernelVersion:	6.3
+Contact:	cristian.marussi@arm.com
+Description:	SCMI Raw asynchronous message injection/snooping facility; write
+		a complete SCMI asynchronous command message (header included)
+		in little-endian binary format to have it sent to the configured
+		backend SCMI server for instance <n> through the <m> transport
+		channel.
+		Any subsequently received response can be read from this same
+		entry if it arrived on channel <m> within the configured
+		timeout.
+		Any additional delayed response received afterwards can be read
+		from this same entry too if it arrived within the configured
+		timeout.
+		Each write to the entry causes one command request to be built
+		and sent while the replies are read back one message at time
+		(receiving an EOF at each message boundary).
+		Channel identifier <m> matches the SCMI protocol number which
+		has been associated with this transport channel in the DT
+		description, with base protocol number 0x10 being the default
+		channel for this instance.
+		Note that these per-channel entries rooted at <..>/channels
+		exist only if the transport is configured to have more than
+		one default channel.
+Users:		Debugging, any userspace test suite
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.yaml b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.yaml
index 0711f1834fbd..d1410345ef18 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.yaml
@@ -31,7 +31,11 @@ properties:
               - mediatek,mt8173-mmsys
               - mediatek,mt8183-mmsys
               - mediatek,mt8186-mmsys
+              - mediatek,mt8188-vdosys0
               - mediatek,mt8192-mmsys
+              - mediatek,mt8195-vdosys1
+              - mediatek,mt8195-vppsys0
+              - mediatek,mt8195-vppsys1
               - mediatek,mt8365-mmsys
           - const: syscon
 
diff --git a/Documentation/devicetree/bindings/firmware/amlogic,meson-gxbb-sm.yaml b/Documentation/devicetree/bindings/firmware/amlogic,meson-gxbb-sm.yaml
new file mode 100644
index 000000000000..8f50e698760e
--- /dev/null
+++ b/Documentation/devicetree/bindings/firmware/amlogic,meson-gxbb-sm.yaml
@@ -0,0 +1,39 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/firmware/amlogic,meson-gxbb-sm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Amlogic Secure Monitor (SM)
+
+description:
+  In the Amlogic SoCs the Secure Monitor code is used to provide access to the
+  NVMEM, enable JTAG, set USB boot, etc...
+
+maintainers:
+  - Neil Armstrong <neil.armstrong@linaro.org>
+
+properties:
+  compatible:
+    oneOf:
+      - const: amlogic,meson-gxbb-sm
+      - items:
+          - const: amlogic,meson-gx-sm
+          - const: amlogic,meson-gxbb-sm
+
+  power-controller:
+    type: object
+    $ref: /schemas/power/amlogic,meson-sec-pwrc.yaml#
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    firmware {
+        secure-monitor {
+            compatible = "amlogic,meson-gxbb-sm";
+        };
+    };
diff --git a/Documentation/devicetree/bindings/firmware/meson/meson_sm.txt b/Documentation/devicetree/bindings/firmware/meson/meson_sm.txt
deleted file mode 100644
index c248cd44f727..000000000000
--- a/Documentation/devicetree/bindings/firmware/meson/meson_sm.txt
+++ /dev/null
@@ -1,15 +0,0 @@
-* Amlogic Secure Monitor
-
-In the Amlogic SoCs the Secure Monitor code is used to provide access to the
-NVMEM, enable JTAG, set USB boot, etc...
-
-Required properties for the secure monitor node:
-- compatible: Should be "amlogic,meson-gxbb-sm"
-
-Example:
-
-	firmware {
-		sm: secure-monitor {
-			compatible = "amlogic,meson-gxbb-sm";
-		};
-	};
diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
index 25688571ee7c..a66e99812b1f 100644
--- a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
+++ b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
@@ -38,6 +38,8 @@ properties:
           - qcom,scm-msm8994
           - qcom,scm-msm8996
           - qcom,scm-msm8998
+          - qcom,scm-qdu1000
+          - qcom,scm-sa8775p
           - qcom,scm-sc7180
           - qcom,scm-sc7280
           - qcom,scm-sc8280xp
@@ -53,6 +55,7 @@ properties:
           - qcom,scm-sm8250
           - qcom,scm-sm8350
           - qcom,scm-sm8450
+          - qcom,scm-sm8550
           - qcom,scm-qcs404
       - const: qcom,scm
 
@@ -73,6 +76,12 @@ properties:
   '#reset-cells':
     const: 1
 
+  interrupts:
+    description:
+      The wait-queue interrupt that firmware raises as part of handshake
+      protocol to handle sleeping SCM calls.
+    maxItems: 1
+
   qcom,dload-mode:
     $ref: /schemas/types.yaml#/definitions/phandle-array
     items:
@@ -82,6 +91,32 @@ properties:
     description: TCSR hardware block
 
 allOf:
+  # Clocks
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,scm-apq8064
+              - qcom,scm-apq8084
+              - qcom,scm-mdm9607
+              - qcom,scm-msm8226
+              - qcom,scm-msm8660
+              - qcom,scm-msm8916
+              - qcom,scm-msm8953
+              - qcom,scm-msm8960
+              - qcom,scm-msm8974
+              - qcom,scm-msm8976
+              - qcom,scm-sm6375
+    then:
+      required:
+        - clocks
+        - clock-names
+    else:
+      properties:
+        clock-names: false
+        clocks: false
+
   - if:
       properties:
         compatible:
@@ -100,10 +135,6 @@ allOf:
         clocks:
           maxItems: 1
 
-      required:
-        - clocks
-        - clock-names
-
   - if:
       properties:
         compatible:
@@ -111,6 +142,7 @@ allOf:
             enum:
               - qcom,scm-apq8084
               - qcom,scm-mdm9607
+              - qcom,scm-msm8226
               - qcom,scm-msm8916
               - qcom,scm-msm8953
               - qcom,scm-msm8974
@@ -127,9 +159,31 @@ allOf:
           minItems: 3
           maxItems: 3
 
-      required:
-        - clocks
-        - clock-names
+  # Interconnects
+  - if:
+      not:
+        properties:
+          compatible:
+            contains:
+              enum:
+                - qcom,scm-sm8450
+                - qcom,scm-sm8550
+    then:
+      properties:
+        interconnects: false
+
+  # Interrupts
+  - if:
+      not:
+        properties:
+          compatible:
+            contains:
+              enum:
+                - qcom,scm-sm8450
+                - qcom,scm-sm8550
+    then:
+      properties:
+        interrupts: false
 
 required:
   - compatible
diff --git a/Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml b/Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml
index 2f72ec418415..037c3ae9f1c3 100644
--- a/Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml
+++ b/Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml
@@ -26,6 +26,7 @@ properties:
     enum:
       - mediatek,mt6323-keys
       - mediatek,mt6331-keys
+      - mediatek,mt6357-keys
       - mediatek,mt6358-keys
       - mediatek,mt6397-keys
 
diff --git a/Documentation/devicetree/bindings/leds/leds-mt6323.txt b/Documentation/devicetree/bindings/leds/leds-mt6323.txt
index 45bf9f7d85f3..73353692efa1 100644
--- a/Documentation/devicetree/bindings/leds/leds-mt6323.txt
+++ b/Documentation/devicetree/bindings/leds/leds-mt6323.txt
@@ -9,7 +9,7 @@ MT6323 PMIC hardware.
 For MT6323 MFD bindings see:
 Documentation/devicetree/bindings/mfd/mt6397.txt
 For MediaTek PMIC wrapper bindings see:
-Documentation/devicetree/bindings/soc/mediatek/pwrap.txt
+Documentation/devicetree/bindings/soc/mediatek/mediatek,pwrap.yaml
 
 Required properties:
 - compatible : Must be "mediatek,mt6323-led"
diff --git a/Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml b/Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml
new file mode 100644
index 000000000000..837a77013d57
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/mediatek,mt6357.yaml
@@ -0,0 +1,111 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/mediatek,mt6357.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek MT6357 PMIC
+
+maintainers:
+  - Flora Fu <flora.fu@mediatek.com>
+  - Alexandre Mergnat <amergnat@baylibre.com>
+
+description: |
+  MT6357 is a power management system chip containing 5 buck
+  converters and 29 LDOs. Supported features are audio codec,
+  USB battery charging, fuel gauge, RTC
+
+  This is a multifunction device with the following sub modules:
+  - Regulator
+  - RTC
+  - Keys
+
+  It is interfaced to host controller using SPI interface by a proprietary hardware
+  called PMIC wrapper or pwrap. This MFD is a child device of pwrap.
+  See the following for pwrap node definitions:
+  Documentation/devicetree/bindings/soc/mediatek/mediatek,pwrap.yaml
+
+properties:
+  compatible:
+    const: mediatek,mt6357
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+
+  regulators:
+    type: object
+    $ref: /schemas/regulator/mediatek,mt6357-regulator.yaml
+    description:
+      List of MT6357 BUCKs and LDOs regulators.
+
+  rtc:
+    type: object
+    $ref: /schemas/rtc/rtc.yaml#
+    description:
+      MT6357 Real Time Clock.
+    properties:
+      compatible:
+        const: mediatek,mt6357-rtc
+      start-year: true
+    required:
+      - compatible
+
+  keys:
+    type: object
+    $ref: /schemas/input/mediatek,pmic-keys.yaml
+    description:
+      MT6357 power and home keys.
+
+required:
+  - compatible
+  - regulators
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    pwrap {
+        pmic {
+            compatible = "mediatek,mt6357";
+
+            interrupt-parent = <&pio>;
+            interrupts = <145 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-controller;
+            #interrupt-cells = <2>;
+
+            regulators {
+                mt6357_vproc_reg: buck-vproc {
+                    regulator-name = "vproc";
+                    regulator-min-microvolt = <518750>;
+                    regulator-max-microvolt = <1312500>;
+                    regulator-ramp-delay = <6250>;
+                    regulator-enable-ramp-delay = <220>;
+                    regulator-always-on;
+                };
+
+                // ...
+
+                mt6357_vusb33_reg: ldo-vusb33 {
+                    regulator-name = "vusb33";
+                    regulator-min-microvolt = <3000000>;
+                    regulator-max-microvolt = <3100000>;
+                    regulator-enable-ramp-delay = <264>;
+                };
+            };
+
+            rtc {
+                compatible = "mediatek,mt6357-rtc";
+            };
+
+            keys {
+                compatible = "mediatek,mt6357-keys";
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/mt6397.txt b/Documentation/devicetree/bindings/mfd/mt6397.txt
index 518986c44880..294693a8906c 100644
--- a/Documentation/devicetree/bindings/mfd/mt6397.txt
+++ b/Documentation/devicetree/bindings/mfd/mt6397.txt
@@ -13,7 +13,7 @@ MT6397/MT6323 is a multifunction device with the following sub modules:
 It is interfaced to host controller using SPI interface by a proprietary hardware
 called PMIC wrapper or pwrap. MT6397/MT6323 MFD is a child device of pwrap.
 See the following for pwarp node definitions:
-../soc/mediatek/pwrap.txt
+../soc/mediatek/mediatek,pwrap.yaml
 
 This document describes the binding for MFD device and its sub module.
 
diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
deleted file mode 100644
index b823b8625243..000000000000
--- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
+++ /dev/null
@@ -1,283 +0,0 @@
-Qualcomm Resource Power Manager (RPM)
-
-This driver is used to interface with the Resource Power Manager (RPM) found in
-various Qualcomm platforms. The RPM allows each component in the system to vote
-for state of the system resources, such as clocks, regulators and bus
-frequencies.
-
-- compatible:
-	Usage: required
-	Value type: <string>
-	Definition: must be one of:
-		    "qcom,rpm-apq8064"
-		    "qcom,rpm-msm8660"
-		    "qcom,rpm-msm8960"
-		    "qcom,rpm-ipq8064"
-		    "qcom,rpm-mdm9615"
-
-- reg:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: base address and size of the RPM's message ram
-
-- interrupts:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: three entries specifying the RPM's:
-		    1. acknowledgement interrupt
-		    2. error interrupt
-		    3. wakeup interrupt
-
-- interrupt-names:
-	Usage: required
-	Value type: <string-array>
-	Definition: must be the three strings "ack", "err" and "wakeup", in order
-
-- qcom,ipc:
-	Usage: required
-	Value type: <prop-encoded-array>
-
-	Definition: three entries specifying the outgoing ipc bit used for
-		    signaling the RPM:
-		    - phandle to a syscon node representing the apcs registers
-		    - u32 representing offset to the register within the syscon
-		    - u32 representing the ipc bit within the register
-
-
-= SUBNODES
-
-The RPM exposes resources to its subnodes. The below bindings specify the set
-of valid subnodes that can operate on these resources.
-
-== Regulators
-
-Regulator nodes are identified by their compatible:
-
-- compatible:
-	Usage: required
-	Value type: <string>
-	Definition: must be one of:
-		    "qcom,rpm-pm8058-regulators"
-		    "qcom,rpm-pm8901-regulators"
-		    "qcom,rpm-pm8921-regulators"
-		    "qcom,rpm-pm8018-regulators"
-		    "qcom,rpm-smb208-regulators"
-
-- vdd_l0_l1_lvs-supply:
-- vdd_l2_l11_l12-supply:
-- vdd_l3_l4_l5-supply:
-- vdd_l6_l7-supply:
-- vdd_l8-supply:
-- vdd_l9-supply:
-- vdd_l10-supply:
-- vdd_l13_l16-supply:
-- vdd_l14_l15-supply:
-- vdd_l17_l18-supply:
-- vdd_l19_l20-supply:
-- vdd_l21-supply:
-- vdd_l22-supply:
-- vdd_l23_l24_l25-supply:
-- vdd_ncp-supply:
-- vdd_s0-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-	Usage: optional (pm8058 only)
-	Value type: <phandle>
-	Definition: reference to regulator supplying the input pin, as
-		    described in the data sheet
-
-- lvs0_in-supply:
-- lvs1_in-supply:
-- lvs2_in-supply:
-- lvs3_in-supply:
-- mvs_in-supply:
-- vdd_l0-supply:
-- vdd_l1-supply:
-- vdd_l2-supply:
-- vdd_l3-supply:
-- vdd_l4-supply:
-- vdd_l5-supply:
-- vdd_l6-supply:
-- vdd_s0-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-	Usage: optional (pm8901 only)
-	Value type: <phandle>
-	Definition: reference to regulator supplying the input pin, as
-		    described in the data sheet
-
-- vdd_l1_l2_l12_l18-supply:
-- vdd_l3_l15_l17-supply:
-- vdd_l4_l14-supply:
-- vdd_l5_l8_l16-supply:
-- vdd_l6_l7-supply:
-- vdd_l9_l11-supply:
-- vdd_l10_l22-supply:
-- vdd_l21_l23_l29-supply:
-- vdd_l24-supply:
-- vdd_l25-supply:
-- vdd_l26-supply:
-- vdd_l27-supply:
-- vdd_l28-supply:
-- vdd_ncp-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_s7-supply:
-- vdd_s8-supply:
-- vin_5vs-supply:
-- vin_lvs1_3_6-supply:
-- vin_lvs2-supply:
-- vin_lvs4_5_7-supply:
-	Usage: optional (pm8921 only)
-	Value type: <phandle>
-	Definition: reference to regulator supplying the input pin, as
-		    described in the data sheet
-
-- vin_lvs1-supply:
-- vdd_l7-supply:
-- vdd_l8-supply:
-- vdd_l9_l10_l11_l12-supply:
-	Usage: optional (pm8018 only)
-	Value type: <phandle>
-	Definition: reference to regulator supplying the input pin, as
-		    described in the data sheet
-
-The regulator node houses sub-nodes for each regulator within the device. Each
-sub-node is identified using the node's name, with valid values listed for each
-of the pmics below.
-
-pm8058:
-	l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
-	l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
-	lvs0, lvs1, ncp
-
-pm8901:
-	l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
-	mvs
-
-pm8921:
-	s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
-	l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
-	l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
-	ncp
-
-pm8018:
-	s1, s2, s3, s4, s5, , l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
-	l12, l14, lvs1
-
-smb208:
-	s1a, s1b, s2a, s2b
-
-The content of each sub-node is defined by the standard binding for regulators -
-see regulator.txt - with additional custom properties described below:
-
-=== Switch-mode Power Supply regulator custom properties
-
-- bias-pull-down:
-	Usage: optional
-	Value type: <empty>
-	Definition: enable pull down of the regulator when inactive
-
-- qcom,switch-mode-frequency:
-	Usage: required
-	Value type: <u32>
-	Definition: Frequency (Hz) of the switch-mode power supply;
-		    must be one of:
-		    19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
-		    2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
-		    1480000, 1370000, 1280000, 1200000
-
-- qcom,force-mode:
-	Usage: optional (default if no other qcom,force-mode is specified)
-	Value type: <u32>
-	Definition: indicates that the regulator should be forced to a
-		   particular mode, valid values are:
-		   QCOM_RPM_FORCE_MODE_NONE - do not force any mode
-		   QCOM_RPM_FORCE_MODE_LPM - force into low power mode
-		   QCOM_RPM_FORCE_MODE_HPM - force into high power mode
-		   QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
-					      select its own mode based on
-					      realtime current draw, only for:
-					      pm8921 smps and ftsmps
-
-- qcom,power-mode-hysteretic:
-	Usage: optional
-	Value type: <empty>
-	Definition: select that the power supply should operate in hysteretic
-		    mode, instead of the default pwm mode
-
-=== Low-dropout regulator custom properties
-
-- bias-pull-down:
-	Usage: optional
-	Value type: <empty>
-	Definition: enable pull down of the regulator when inactive
-
-- qcom,force-mode:
-	Usage: optional
-	Value type: <u32>
-	Definition: indicates that the regulator should not be forced to any
-		   particular mode, valid values are:
-		   QCOM_RPM_FORCE_MODE_NONE - do not force any mode
-		   QCOM_RPM_FORCE_MODE_LPM - force into low power mode
-		   QCOM_RPM_FORCE_MODE_HPM - force into high power mode
-		   QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
-						mode, i.e.  to act as a switch
-						and not regulate, only for:
-						pm8921 pldo, nldo and nldo1200
-
-=== Negative Charge Pump custom properties
-
-- qcom,switch-mode-frequency:
-	Usage: required
-	Value type: <u32>
-	Definition: Frequency (Hz) of the switch mode power supply;
-		    must be one of:
-		    19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
-		    2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
-		    1480000, 1370000, 1280000, 1200000
-
-= EXAMPLE
-
-	#include <dt-bindings/mfd/qcom-rpm.h>
-
-	rpm@108000 {
-		compatible = "qcom,rpm-msm8960";
-		reg = <0x108000 0x1000>;
-		qcom,ipc = <&apcs 0x8 2>;
-
-		interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
-		interrupt-names = "ack", "err", "wakeup";
-
-		regulators {
-			compatible = "qcom,rpm-pm8921-regulators";
-			vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-
-			s1 {
-				regulator-min-microvolt = <1225000>;
-				regulator-max-microvolt = <1225000>;
-
-				bias-pull-down;
-
-				qcom,switch-mode-frequency = <3200000>;
-			};
-
-			pm8921_s4: s4 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-
-				qcom,switch-mode-frequency = <1600000>;
-				bias-pull-down;
-
-				qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
-			};
-		};
-	};
-
diff --git a/Documentation/devicetree/bindings/phy/samsung,dp-video-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,dp-video-phy.yaml
index b03b2f00cc5b..3bee3f8733f7 100644
--- a/Documentation/devicetree/bindings/phy/samsung,dp-video-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/samsung,dp-video-phy.yaml
@@ -22,13 +22,13 @@ properties:
 
   samsung,pmu-syscon:
     $ref: /schemas/types.yaml#/definitions/phandle
+    deprecated: true
     description:
-      Phandle to PMU system controller interface.
+      Phandle to PMU system controller interface (if not a child of PMU).
 
 required:
   - compatible
   - "#phy-cells"
-  - samsung,pmu-syscon
 
 additionalProperties: false
 
@@ -36,6 +36,5 @@ examples:
   - |
     phy {
         compatible = "samsung,exynos5420-dp-video-phy";
-        samsung,pmu-syscon = <&pmu_system_controller>;
         #phy-cells = <0>;
     };
diff --git a/Documentation/devicetree/bindings/phy/samsung,mipi-video-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,mipi-video-phy.yaml
index 415440aaad89..b2250e4a6b1b 100644
--- a/Documentation/devicetree/bindings/phy/samsung,mipi-video-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/samsung,mipi-video-phy.yaml
@@ -35,15 +35,18 @@ properties:
 
   syscon:
     $ref: /schemas/types.yaml#/definitions/phandle
+    deprecated: true
     description:
       Phandle to PMU system controller interface, valid only for
-      samsung,s5pv210-mipi-video-phy and samsung,exynos5420-mipi-video-phy.
+      samsung,s5pv210-mipi-video-phy and samsung,exynos5420-mipi-video-phy (if
+      not a child of PMU).
 
   samsung,pmu-syscon:
     $ref: /schemas/types.yaml#/definitions/phandle
+    deprecated: true
     description:
       Phandle to PMU system controller interface, valid for
-      samsung,exynos5433-mipi-video-phy.
+      samsung,exynos5433-mipi-video-phy (if not a child of PMU).
 
   samsung,disp-sysreg:
     $ref: /schemas/types.yaml#/definitions/phandle
@@ -81,13 +84,10 @@ allOf:
         samsung,disp-sysreg: false
         samsung,cam0-sysreg: false
         samsung,cam1-sysreg: false
-      required:
-        - syscon
     else:
       properties:
         syscon: false
       required:
-        - samsung,pmu-syscon
         - samsung,disp-sysreg
         - samsung,cam0-sysreg
         - samsung,cam1-sysreg
@@ -99,7 +99,6 @@ examples:
     phy {
         compatible = "samsung,exynos5433-mipi-video-phy";
         #phy-cells = <1>;
-        samsung,pmu-syscon = <&pmu_system_controller>;
         samsung,cam0-sysreg = <&syscon_cam0>;
         samsung,cam1-sysreg = <&syscon_cam1>;
         samsung,disp-sysreg = <&syscon_disp>;
diff --git a/Documentation/devicetree/bindings/power/allwinner,sun20i-d1-ppu.yaml b/Documentation/devicetree/bindings/power/allwinner,sun20i-d1-ppu.yaml
new file mode 100644
index 000000000000..46e2647a5d72
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/allwinner,sun20i-d1-ppu.yaml
@@ -0,0 +1,54 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/allwinner,sun20i-d1-ppu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner SoCs PPU power domain controller
+
+maintainers:
+  - Samuel Holland <samuel@sholland.org>
+
+description:
+  D1 and related SoCs contain a power domain controller for the CPUs, GPU, and
+  video-related hardware.
+
+properties:
+  compatible:
+    enum:
+      - allwinner,sun20i-d1-ppu
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description: Bus Clock
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  '#power-domain-cells':
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - resets
+  - '#power-domain-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/sun20i-d1-r-ccu.h>
+    #include <dt-bindings/reset/sun20i-d1-r-ccu.h>
+
+    ppu: power-controller@7001000 {
+        compatible = "allwinner,sun20i-d1-ppu";
+        reg = <0x7001000 0x1000>;
+        clocks = <&r_ccu CLK_BUS_R_PPU>;
+        resets = <&r_ccu RST_BUS_R_PPU>;
+        #power-domain-cells = <1>;
+    };
diff --git a/Documentation/devicetree/bindings/power/amlogic,meson-gx-pwrc.txt b/Documentation/devicetree/bindings/power/amlogic,meson-gx-pwrc.txt
index 99b5b10cda31..ba5865ae6bfe 100644
--- a/Documentation/devicetree/bindings/power/amlogic,meson-gx-pwrc.txt
+++ b/Documentation/devicetree/bindings/power/amlogic,meson-gx-pwrc.txt
@@ -1,5 +1,5 @@
-Amlogic Meson Power Controller
-==============================
+Amlogic Meson Power Controller (deprecated)
+===========================================
 
 The Amlogic Meson SoCs embeds an internal Power domain controller.
 
diff --git a/Documentation/devicetree/bindings/power/mediatek,power-controller.yaml b/Documentation/devicetree/bindings/power/mediatek,power-controller.yaml
index 605ec7ab5f63..c9acef80f452 100644
--- a/Documentation/devicetree/bindings/power/mediatek,power-controller.yaml
+++ b/Documentation/devicetree/bindings/power/mediatek,power-controller.yaml
@@ -28,6 +28,7 @@ properties:
       - mediatek,mt8173-power-controller
       - mediatek,mt8183-power-controller
       - mediatek,mt8186-power-controller
+      - mediatek,mt8188-power-controller
       - mediatek,mt8192-power-controller
       - mediatek,mt8195-power-controller
 
@@ -84,6 +85,7 @@ $defs:
               "include/dt-bindings/power/mt8167-power.h" - for MT8167 type power domain.
               "include/dt-bindings/power/mt8173-power.h" - for MT8173 type power domain.
               "include/dt-bindings/power/mt8183-power.h" - for MT8183 type power domain.
+              "include/dt-bindings/power/mediatek,mt8188-power.h" - for MT8188 type power domain.
               "include/dt-bindings/power/mt8192-power.h" - for MT8192 type power domain.
               "include/dt-bindings/power/mt8195-power.h" - for MT8195 type power domain.
         maxItems: 1
diff --git a/Documentation/devicetree/bindings/power/qcom,rpmpd.yaml b/Documentation/devicetree/bindings/power/qcom,rpmpd.yaml
index 633d49884019..afad3135ed67 100644
--- a/Documentation/devicetree/bindings/power/qcom,rpmpd.yaml
+++ b/Documentation/devicetree/bindings/power/qcom,rpmpd.yaml
@@ -30,6 +30,7 @@ properties:
       - qcom,qcs404-rpmpd
       - qcom,qdu1000-rpmhpd
       - qcom,sa8540p-rpmhpd
+      - qcom,sa8775p-rpmhpd
       - qcom,sdm660-rpmpd
       - qcom,sc7180-rpmhpd
       - qcom,sc7280-rpmhpd
@@ -39,7 +40,6 @@ properties:
       - qcom,sdm845-rpmhpd
       - qcom,sdx55-rpmhpd
       - qcom,sdx65-rpmhpd
-      - qcom,sm4250-rpmpd
       - qcom,sm6115-rpmpd
       - qcom,sm6125-rpmpd
       - qcom,sm6350-rpmhpd
diff --git a/Documentation/devicetree/bindings/power/starfive,jh7110-pmu.yaml b/Documentation/devicetree/bindings/power/starfive,jh7110-pmu.yaml
new file mode 100644
index 000000000000..98eb8b4110e7
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/starfive,jh7110-pmu.yaml
@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/starfive,jh7110-pmu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 Power Management Unit
+
+maintainers:
+  - Walker Chen <walker.chen@starfivetech.com>
+
+description: |
+  StarFive JH7110 SoC includes support for multiple power domains which can be
+  powered on/off by software based on different application scenes to save power.
+
+properties:
+  compatible:
+    enum:
+      - starfive,jh7110-pmu
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  "#power-domain-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#power-domain-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    pwrc: power-controller@17030000 {
+        compatible = "starfive,jh7110-pmu";
+        reg = <0x17030000 0x10000>;
+        interrupts = <111>;
+        #power-domain-cells = <1>;
+    };
diff --git a/Documentation/devicetree/bindings/reserved-memory/qcom,rmtfs-mem.yaml b/Documentation/devicetree/bindings/reserved-memory/qcom,rmtfs-mem.yaml
index 2998f1c8f0db..08eb10c25821 100644
--- a/Documentation/devicetree/bindings/reserved-memory/qcom,rmtfs-mem.yaml
+++ b/Documentation/devicetree/bindings/reserved-memory/qcom,rmtfs-mem.yaml
@@ -27,9 +27,11 @@ properties:
       identifier of the client to use this region for buffers
 
   qcom,vmid:
-    $ref: /schemas/types.yaml#/definitions/uint32
+    $ref: /schemas/types.yaml#/definitions/uint32-array
     description: >
-      vmid of the remote processor, to set up memory protection
+      Array of vmids of the remote processors, to set up memory protection
+    minItems: 1
+    maxItems: 2
 
 required:
   - qcom,client-id
diff --git a/Documentation/devicetree/bindings/riscv/sifive,ccache0.yaml b/Documentation/devicetree/bindings/riscv/sifive,ccache0.yaml
index 0551a0d1b3df..eb6ab73c0f31 100644
--- a/Documentation/devicetree/bindings/riscv/sifive,ccache0.yaml
+++ b/Documentation/devicetree/bindings/riscv/sifive,ccache0.yaml
@@ -38,6 +38,10 @@ properties:
               - sifive,fu740-c000-ccache
           - const: cache
       - items:
+          - const: starfive,jh7110-ccache
+          - const: sifive,ccache0
+          - const: cache
+      - items:
           - const: microchip,mpfs-ccache
           - const: sifive,fu540-c000-ccache
           - const: cache
@@ -84,6 +88,7 @@ allOf:
           contains:
             enum:
               - sifive,fu740-c000-ccache
+              - starfive,jh7110-ccache
               - microchip,mpfs-ccache
 
     then:
@@ -104,7 +109,9 @@ allOf:
       properties:
         compatible:
           contains:
-            const: sifive,fu740-c000-ccache
+            enum:
+              - sifive,fu740-c000-ccache
+              - starfive,jh7110-ccache
 
     then:
       properties:
diff --git a/Documentation/devicetree/bindings/soc/mediatek/mediatek,mutex.yaml b/Documentation/devicetree/bindings/soc/mediatek/mediatek,mutex.yaml
index 9241e5fc7cff..15c133cac315 100644
--- a/Documentation/devicetree/bindings/soc/mediatek/mediatek,mutex.yaml
+++ b/Documentation/devicetree/bindings/soc/mediatek/mediatek,mutex.yaml
@@ -32,6 +32,7 @@ properties:
       - mediatek,mt8183-disp-mutex
       - mediatek,mt8186-disp-mutex
       - mediatek,mt8186-mdp3-mutex
+      - mediatek,mt8188-disp-mutex
       - mediatek,mt8192-disp-mutex
       - mediatek,mt8195-disp-mutex
 
diff --git a/Documentation/devicetree/bindings/soc/mediatek/mediatek,pwrap.yaml b/Documentation/devicetree/bindings/soc/mediatek/mediatek,pwrap.yaml
new file mode 100644
index 000000000000..3fefd634bc69
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/mediatek/mediatek,pwrap.yaml
@@ -0,0 +1,147 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/mediatek/mediatek,pwrap.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek PMIC Wrapper
+
+maintainers:
+  - Flora Fu <flora.fu@mediatek.com>
+  - Alexandre Mergnat <amergnat@baylibre.com>
+
+description:
+  On MediaTek SoCs the PMIC is connected via SPI. The SPI master interface
+  is not directly visible to the CPU, but only through the PMIC wrapper
+  inside the SoC. The communication between the SoC and the PMIC can
+  optionally be encrypted. Also a non standard Dual IO SPI mode can be
+  used to increase speed.
+
+  IP Pairing
+
+  On MT8135 the pins of some SoC internal peripherals can be on the PMIC.
+  The signals of these pins are routed over the SPI bus using the pwrap
+  bridge. In the binding description below the properties needed for bridging
+  are marked with "IP Pairing". These are optional on SoCs which do not support
+  IP Pairing
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - mediatek,mt2701-pwrap
+              - mediatek,mt6765-pwrap
+              - mediatek,mt6779-pwrap
+              - mediatek,mt6797-pwrap
+              - mediatek,mt6873-pwrap
+              - mediatek,mt7622-pwrap
+              - mediatek,mt8135-pwrap
+              - mediatek,mt8173-pwrap
+              - mediatek,mt8183-pwrap
+              - mediatek,mt8186-pwrap
+              - mediatek,mt8188-pwrap
+              - mediatek,mt8195-pwrap
+              - mediatek,mt8365-pwrap
+              - mediatek,mt8516-pwrap
+      - items:
+          - enum:
+              - mediatek,mt8186-pwrap
+              - mediatek,mt8195-pwrap
+          - const: syscon
+
+  reg:
+    minItems: 1
+    items:
+      - description: PMIC wrapper registers
+      - description: IP pairing registers
+
+  reg-names:
+    minItems: 1
+    items:
+      - const: pwrap
+      - const: pwrap-bridge
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    minItems: 2
+    items:
+      - description: SPI bus clock
+      - description: Main module clock
+      - description: System module clock
+      - description: Timer module clock
+
+  clock-names:
+    minItems: 2
+    items:
+      - const: spi
+      - const: wrap
+      - const: sys
+      - const: tmr
+
+  resets:
+    minItems: 1
+    items:
+      - description: PMIC wrapper reset
+      - description: IP pairing reset
+
+  reset-names:
+    minItems: 1
+    items:
+      - const: pwrap
+      - const: pwrap-bridge
+
+  pmic:
+    type: object
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - clocks
+  - clock-names
+
+dependentRequired:
+  resets: [reset-names]
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt8365-pwrap
+    then:
+      properties:
+        clocks:
+          minItems: 4
+
+        clock-names:
+          minItems: 4
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/reset/mt8135-resets.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+        pwrap@1000f000 {
+            compatible = "mediatek,mt8135-pwrap";
+            reg = <0 0x1000f000 0 0x1000>,
+                  <0 0x11017000 0 0x1000>;
+            reg-names = "pwrap", "pwrap-bridge";
+            interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+            clocks = <&clk26m>, <&clk26m>;
+            clock-names = "spi", "wrap";
+            resets = <&infracfg MT8135_INFRA_PMIC_WRAP_RST>,
+                     <&pericfg MT8135_PERI_PWRAP_BRIDGE_SW_RST>;
+            reset-names = "pwrap", "pwrap-bridge";
+        };
+    };
diff --git a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt
deleted file mode 100644
index 12e4b4260b40..000000000000
--- a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt
+++ /dev/null
@@ -1,75 +0,0 @@
-MediaTek PMIC Wrapper Driver
-
-This document describes the binding for the MediaTek PMIC wrapper.
-
-On MediaTek SoCs the PMIC is connected via SPI. The SPI master interface
-is not directly visible to the CPU, but only through the PMIC wrapper
-inside the SoC. The communication between the SoC and the PMIC can
-optionally be encrypted. Also a non standard Dual IO SPI mode can be
-used to increase speed.
-
-IP Pairing
-
-on MT8135 the pins of some SoC internal peripherals can be on the PMIC.
-The signals of these pins are routed over the SPI bus using the pwrap
-bridge. In the binding description below the properties needed for bridging
-are marked with "IP Pairing". These are optional on SoCs which do not support
-IP Pairing
-
-Required properties in pwrap device node.
-- compatible:
-	"mediatek,mt2701-pwrap" for MT2701/7623 SoCs
-	"mediatek,mt6765-pwrap" for MT6765 SoCs
-	"mediatek,mt6779-pwrap" for MT6779 SoCs
-	"mediatek,mt6797-pwrap" for MT6797 SoCs
-	"mediatek,mt6873-pwrap" for MT6873/8192 SoCs
-	"mediatek,mt7622-pwrap" for MT7622 SoCs
-	"mediatek,mt8135-pwrap" for MT8135 SoCs
-	"mediatek,mt8173-pwrap" for MT8173 SoCs
-	"mediatek,mt8183-pwrap" for MT8183 SoCs
-	"mediatek,mt8186-pwrap" for MT8186 SoCs
-	"mediatek,mt8188-pwrap", "mediatek,mt8195-pwrap" for MT8188 SoCs
-	"mediatek,mt8195-pwrap" for MT8195 SoCs
-	"mediatek,mt8365-pwrap" for MT8365 SoCs
-	"mediatek,mt8516-pwrap" for MT8516 SoCs
-- interrupts: IRQ for pwrap in SOC
-- reg-names: "pwrap" is required; "pwrap-bridge" is optional.
-  "pwrap": Main registers base
-  "pwrap-bridge": bridge base (IP Pairing)
-- reg: Must contain an entry for each entry in reg-names.
-- clock-names: Must include the following entries:
-  "spi": SPI bus clock
-  "wrap": Main module clock
-  "sys": Optional system module clock
-  "tmr": Optional timer module clock
-- clocks: Must contain an entry for each entry in clock-names.
-
-Optional properities:
-- reset-names: Some SoCs include the following entries:
-  "pwrap"
-  "pwrap-bridge" (IP Pairing)
-- resets: Must contain an entry for each entry in reset-names.
-- pmic: Using either MediaTek PMIC MFD as the child device of pwrap
-  See the following for child node definitions:
-  Documentation/devicetree/bindings/mfd/mt6397.txt
-  or the regulator-only device as the child device of pwrap, such as MT6380.
-  See the following definitions for such kinds of devices.
-  Documentation/devicetree/bindings/regulator/mt6380-regulator.txt
-
-Example:
-	pwrap: pwrap@1000f000 {
-		compatible = "mediatek,mt8135-pwrap";
-		reg = <0 0x1000f000 0 0x1000>,
-			<0 0x11017000 0 0x1000>;
-		reg-names = "pwrap", "pwrap-bridge";
-		interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
-		resets = <&infracfg MT8135_INFRA_PMIC_WRAP_RST>,
-				<&pericfg MT8135_PERI_PWRAP_BRIDGE_SW_RST>;
-		reset-names = "pwrap", "pwrap-bridge";
-		clocks = <&clk26m>, <&clk26m>;
-		clock-names = "spi", "wrap";
-
-		pmic {
-			compatible = "mediatek,mt6397";
-		};
-	};
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,dcc.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,dcc.yaml
new file mode 100644
index 000000000000..ce7e20dd22c9
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,dcc.yaml
@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,dcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Data Capture and Compare
+
+maintainers:
+  - Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+
+description: |
+    DCC (Data Capture and Compare) is a DMA engine which is used to save
+    configuration data or system memory contents during catastrophic failure
+    or SW trigger. DCC is used to capture and store data for debugging purpose
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - qcom,sm8150-dcc
+          - qcom,sc7280-dcc
+          - qcom,sc7180-dcc
+          - qcom,sdm845-dcc
+      - const: qcom,dcc
+
+  reg:
+    items:
+      - description: DCC base
+      - description: DCC RAM base
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    dma@10a2000{
+        compatible = "qcom,sm8150-dcc", "qcom,dcc";
+        reg = <0x010a2000 0x1000>,
+              <0x010ad000 0x2000>;
+    };
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,msm8976-ramp-controller.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,msm8976-ramp-controller.yaml
new file mode 100644
index 000000000000..aae9cf7b8caf
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,msm8976-ramp-controller.yaml
@@ -0,0 +1,36 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,msm8976-ramp-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Ramp Controller
+
+maintainers:
+  - AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
+
+description:
+  The Ramp Controller is used to program the sequence ID for pulse
+  swallowing, enable sequences and link Sequence IDs (SIDs) for the
+  CPU cores on some Qualcomm SoCs.
+
+properties:
+  compatible:
+    enum:
+      - qcom,msm8976-ramp-controller
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    cpu-power-controller@b014000 {
+        compatible = "qcom,msm8976-ramp-controller";
+        reg = <0x0b014000 0x68>;
+    };
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
new file mode 100644
index 000000000000..cf863683c21a
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
@@ -0,0 +1,95 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,pmic-glink.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm PMIC GLINK firmware interface for battery management, USB
+  Type-C and other things.
+
+maintainers:
+  - Bjorn Andersson <andersson@kernel.org>
+
+description:
+  The PMIC GLINK service, running on a coprocessor on some modern Qualcomm
+  platforms and implement USB Type-C handling and battery management. This
+  binding describes the component in the OS used to communicate with the
+  firmware and connect it's resources to those described in the Devicetree,
+  particularly the USB Type-C controllers relationship with USB and DisplayPort
+  components.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - qcom,sc8180x-pmic-glink
+          - qcom,sc8280xp-pmic-glink
+          - qcom,sm8350-pmic-glink
+      - const: qcom,pmic-glink
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+patternProperties:
+  '^connector@\d$':
+    $ref: /schemas/connector/usb-connector.yaml#
+
+    properties:
+      reg: true
+
+    required:
+      - reg
+
+    unevaluatedProperties: false
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |+
+    pmic-glink {
+        compatible = "qcom,sc8280xp-pmic-glink", "qcom,pmic-glink";
+
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        connector@0 {
+            compatible = "usb-c-connector";
+            reg = <0>;
+            power-role = "dual";
+            data-role = "dual";
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    endpoint {
+                        remote-endpoint = <&usb_role>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    endpoint {
+                        remote-endpoint = <&ss_phy_out>;
+                    };
+                };
+
+                port@2 {
+                    reg = <2>;
+                    endpoint {
+                        remote-endpoint = <&sbu_mux>;
+                    };
+                };
+            };
+        };
+    };
+...
+
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,rpm.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,rpm.yaml
new file mode 100644
index 000000000000..b00be9e01206
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,rpm.yaml
@@ -0,0 +1,101 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,rpm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Resource Power Manager (RPM)
+
+description:
+  This driver is used to interface with the Resource Power Manager (RPM) found
+  in various Qualcomm platforms. The RPM allows each component in the system
+  to vote for state of the system resources, such as clocks, regulators and bus
+  frequencies.
+
+maintainers:
+  - Bjorn Andersson <andersson@kernel.org>
+
+properties:
+  compatible:
+    enum:
+      - qcom,rpm-apq8064
+      - qcom,rpm-msm8660
+      - qcom,rpm-msm8960
+      - qcom,rpm-ipq8064
+      - qcom,rpm-mdm9615
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 3
+
+  interrupt-names:
+    items:
+      - const: ack
+      - const: err
+      - const: wakeup
+
+  qcom,ipc:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    items:
+      - items:
+          - description: phandle to a syscon node representing the APCS registers
+          - description: u32 representing offset to the register within the syscon
+          - description: u32 representing the ipc bit within the register
+    description:
+      Three entries specifying the outgoing ipc bit used for signaling the RPM.
+
+patternProperties:
+  "^regulators(-[01])?$":
+    type: object
+    $ref: /schemas/regulator/qcom,rpm-regulator.yaml#
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-names
+  - qcom,ipc
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/mfd/qcom-rpm.h>
+
+    rpm@108000 {
+      compatible = "qcom,rpm-msm8960";
+      reg = <0x108000 0x1000>;
+      qcom,ipc = <&apcs 0x8 2>;
+
+      interrupts = <GIC_SPI 19 IRQ_TYPE_NONE>, <GIC_SPI 21 IRQ_TYPE_NONE>, <GIC_SPI 22 IRQ_TYPE_NONE>;
+      interrupt-names = "ack", "err", "wakeup";
+
+      regulators {
+        compatible = "qcom,rpm-pm8921-regulators";
+        vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+
+        s1 {
+          regulator-min-microvolt = <1225000>;
+          regulator-max-microvolt = <1225000>;
+
+          bias-pull-down;
+
+          qcom,switch-mode-frequency = <3200000>;
+        };
+
+        pm8921_s4: s4 {
+          regulator-min-microvolt = <1800000>;
+          regulator-max-microvolt = <1800000>;
+
+          qcom,switch-mode-frequency = <1600000>;
+          bias-pull-down;
+
+          qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+        };
+      };
+    };
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,rpmh-rsc.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,rpmh-rsc.yaml
index b246500d3d5d..a4046ba60846 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,rpmh-rsc.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,rpmh-rsc.yaml
@@ -112,8 +112,9 @@ properties:
     $ref: /schemas/power/qcom,rpmpd.yaml#
 
 patternProperties:
-  '-regulators$':
+  '^regulators(-[0-9])?$':
     $ref: /schemas/regulator/qcom,rpmh-regulator.yaml#
+    unevaluatedProperties: false
 
 required:
   - compatible
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
index 11c0f4dd797c..16fd67c0bd1f 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
@@ -80,6 +80,7 @@ if:
         enum:
           - qcom,rpm-apq8084
           - qcom,rpm-msm8916
+          - qcom,rpm-msm8936
           - qcom,rpm-msm8974
           - qcom,rpm-msm8976
           - qcom,rpm-msm8953