summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
diff options
context:
space:
mode:
authorPablo Greco <pgreco@centosproject.org>2019-05-02 16:33:49 +0300
committerMaxime Ripard <maxime.ripard@bootlin.com>2019-05-20 10:27:31 +0300
commit3e4a856af3154cf65428818123a7a9fb94a65214 (patch)
treef2da3f58867a943dc4534cdee614d34c5db32999 /arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
parent78f8e6d97fa0bc97e6bbf88c8f1eba3a01138634 (diff)
downloadlinux-3e4a856af3154cf65428818123a7a9fb94a65214.tar.xz
ARM: dts: sun8i: v40: bananapi-m2-berry: Add Bluetooth device node
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side identifies as BCM43430, while the Bluetooth side identifies as BCM43438. The Bluetooth side is connected to UART3 in a 4 wire configuration. Same as the WiFi side, due to being the same chip and package, DLDO1 and DLDO2 regulator outputs from the PMIC provide overall power via VBAT and I/O power via VDDIO. The CLK_OUT_A clock output from the SoC provides the LPO low power clock at 32.768 kHz. This patch enables Bluetooth on this board, and also adds the missing LPO clock on the WiFi side. There is also a PCM connection for Bluetooth, but this is not covered here. The LPO clock is fed from CLK_OUT_A, which needs to be muxed on pin PI12. This can be represented in multiple ways. This patch puts the pinctrl property in the pin controller node. This is due to limitations in Linux, where pinmux settings, even the same one, can not be shared by multiple devices. Thus we cannot put it in both the WiFi and Bluetooth device nodes. Putting it the CCU node is another option, but Linux's CCU driver does not handle pinctrl. Also the pin controller is guaranteed to be initialized after the CCU, when clocks are available. And any other devices that use muxed pins are guaranteed to be initialized after the pin controller. Thus having the CLK_OUT_A pinmux reference be in the pin controller node is a good choice without having to deal with implementation issues. Signed-off-by: Pablo Greco <pgreco@centosproject.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Diffstat (limited to 'arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts')
-rw-r--r--arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts38
1 files changed, 38 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
index 461683c6d1fb..15c22b06fc4b 100644
--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -96,6 +96,8 @@
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
+ clocks = <&ccu CLK_OUTA>;
+ clock-names = "ext_clock";
};
};
@@ -172,6 +174,8 @@
};
&pio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&clk_out_a_pin>;
vcc-pa-supply = <&reg_aldo2>;
vcc-pc-supply = <&reg_dcdc1>;
vcc-pd-supply = <&reg_dcdc1>;
@@ -233,12 +237,27 @@
regulator-name = "vcc-wifi-io";
};
+/*
+ * Our WiFi chip needs both DLDO2 and DLDO3 to be powered at the same
+ * time, with the two being in sync, to be able to meet maximum power
+ * consumption during transmits. Since this is not really supported
+ * right now, just use the two as always on, and we will fix it later.
+ */
+
&reg_dldo2 {
+ regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
};
+&reg_dldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-2";
+};
+
&reg_dldo4 {
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
@@ -261,6 +280,25 @@
status = "okay";
};
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pg_pins>, <&uart3_rts_cts_pg_pins>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&ccu CLK_OUTA>;
+ clock-names = "lpo";
+ vbat-supply = <&reg_dldo2>;
+ vddio-supply = <&reg_dldo1>;
+ device-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+ /* TODO host wake line connected to PMIC GPIO pins */
+ shutdown-gpios = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */
+ max-speed = <1500000>;
+ };
+};
+
&usbphy {
usb1_vbus-supply = <&reg_vcc5v0>;
status = "okay";