Merge tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull SoC DT updates from Arnd Bergmann:
 "About a quarter of the changes are for 32-bit arm, mostly filling in
  device support for existing machines and adding minor cleanups, mostly
  for Qualcomm and Samsung based machines.

  Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
  Rockchips that have been around for a while but were lacking kernel
  support so far: RV1126 is a Vision SoC with an NPU and is used in the
  Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
  for TV boxes and so far only comes with a dts for its refernece
  design.

  The other 32-bit boards that were added are two ASpeed AST2600 based
  BMC boards, the Microchip sam9x60_curiosity development board (Armv5
  based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
  for i.MX53 and i.MX6ULL.

  On the RISC-V side, there are fewer patches, but a total of ten new
  single-board computers based on variations of the Allwinner D1/T113
  chip, plus one more board based on Microchip Polarfire.

  As usual, arm64 has by far the most changes here, with over 700
  non-merge changesets, among them over 400 alone for Qualcomm. The
  newly added SoCs this time are all recent high-end embedded SoCs for
  various markets, each on comes with support for its reference board:

   - Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
   - Qualcomm QDU1000/QRU1000 5G RAN platform
   - Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
   - TI J784S4 for industrial and automotive applications

  In total, there are 46 new arm64 machines:
   - Reference platforms for each of the five new SoCs
   - Three Amlogic based development boards
   - Six embedded machines based on NXP i.MX8MM and i.MX8MP
   - The Mediatek mt7986a based Banana Pi R3 router
   - Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
     (Snapdragon 662) and SM8250 (Snapdragon 865)
   - Two LTE dongles, also based on MSM8916
   - Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
     SDM450 and SDM632
   - Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
   - Nine development boards based on Rockchips RK3588, RK3568, RK3566
     and RK3328.
   - Five development machines based on TI K3 (AM642/AM654/AM68/AM69)

  The cleanup of dtc warnings continues across all platforms, adding to
  the total number of changes"

* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
  dt-bindings: riscv: correct starfive visionfive 2 compatibles
  ARM: dts: socfpga: Add enclustra PE1 devicetree
  dt-bindings: altera: Add enclustra mercury PE1
  arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
  arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
  arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
  arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
  arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
  arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
  arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
  arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
  arm64: dts: qcom: pmk8350: Use the correct PON compatible
  arm64: dts: qcom: sc8280xp-x13s: Enable external display
  arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
  arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
  arm64: dts: qcom: sm8350-hdk: enable GPU
  arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
  arm64: dts: qcom: sm8350: finish reordering nodes
  arm64: dts: qcom: sm8350: move more nodes to correct place
  arm64: dts: qcom: sm8350: reorder device nodes
  ...

25 files changed, 2168 insertions, 40 deletions

diff --git a/arch/riscv/Kconfig.socs b/arch/riscv/Kconfig.socs
index 4b6deb2715f1..4b91367604ea 100644
--- a/arch/riscv/Kconfig.socs
+++ b/arch/riscv/Kconfig.socs
@@ -1,8 +1,10 @@
 menu "SoC selection"
 
+config ARCH_MICROCHIP_POLARFIRE
+	def_bool SOC_MICROCHIP_POLARFIRE
+
 config SOC_MICROCHIP_POLARFIRE
 	bool "Microchip PolarFire SoCs"
-	select MCHP_CLK_MPFS
 	help
 	  This enables support for Microchip PolarFire SoC platforms.
 
@@ -11,16 +13,18 @@ config ARCH_RENESAS
 	help
 	  This enables support for the RISC-V based Renesas SoCs.
 
+config ARCH_SIFIVE
+	def_bool SOC_SIFIVE
+
 config SOC_SIFIVE
 	bool "SiFive SoCs"
-	select SERIAL_SIFIVE if TTY
-	select SERIAL_SIFIVE_CONSOLE if TTY
-	select CLK_SIFIVE
-	select CLK_SIFIVE_PRCI
 	select ERRATA_SIFIVE if !XIP_KERNEL
 	help
 	  This enables support for SiFive SoC platform hardware.
 
+config ARCH_STARFIVE
+	def_bool SOC_STARFIVE
+
 config SOC_STARFIVE
 	bool "StarFive SoCs"
 	select PINCTRL
@@ -28,6 +32,18 @@ config SOC_STARFIVE
 	help
 	  This enables support for StarFive SoC platform hardware.
 
+config ARCH_SUNXI
+	bool "Allwinner sun20i SoCs"
+	depends on MMU && !XIP_KERNEL
+	select ERRATA_THEAD
+	select SUN4I_TIMER
+	help
+	  This enables support for Allwinner sun20i platform hardware,
+	  including boards based on the D1 and D1s SoCs.
+
+config ARCH_VIRT
+	def_bool SOC_VIRT
+	
 config SOC_VIRT
 	bool "QEMU Virt Machine"
 	select CLINT_TIMER if RISCV_M_MODE
@@ -42,24 +58,27 @@ config SOC_VIRT
 	help
 	  This enables support for QEMU Virt Machine.
 
+config ARCH_CANAAN
+	def_bool SOC_CANAAN
+
 config SOC_CANAAN
 	bool "Canaan Kendryte K210 SoC"
 	depends on !MMU
 	select CLINT_TIMER if RISCV_M_MODE
-	select SERIAL_SIFIVE if TTY
-	select SERIAL_SIFIVE_CONSOLE if TTY
 	select ARCH_HAS_RESET_CONTROLLER
 	select PINCTRL
 	select COMMON_CLK
-	select COMMON_CLK_K210
 	help
 	  This enables support for Canaan Kendryte K210 SoC platform hardware.
 
-if SOC_CANAAN
+if ARCH_CANAAN
+
+config ARCH_CANAAN_K210_DTB_BUILTIN
+	def_bool SOC_CANAAN_K210_DTB_BUILTIN
 
 config SOC_CANAAN_K210_DTB_BUILTIN
 	bool "Builtin device tree for the Canaan Kendryte K210"
-	depends on SOC_CANAAN
+	depends on ARCH_CANAAN
 	default y
 	select OF
 	select BUILTIN_DTB
@@ -68,16 +87,19 @@ config SOC_CANAAN_K210_DTB_BUILTIN
 	  This option should be selected if no bootloader is being used.
 	  If unsure, say Y.
 
+config ARCH_CANAAN_K210_DTB_SOURCE
+	def_bool SOC_CANAAN_K210_DTB_SOURCE
+
 config SOC_CANAAN_K210_DTB_SOURCE
 	string "Source file for the Canaan Kendryte K210 builtin DTB"
-	depends on SOC_CANAAN
-	depends on SOC_CANAAN_K210_DTB_BUILTIN
+	depends on ARCH_CANAAN
+	depends on ARCH_CANAAN_K210_DTB_BUILTIN
 	default "k210_generic"
 	help
 	  Base name (without suffix, relative to arch/riscv/boot/dts/canaan)
 	  for the DTS file that will be used to produce the DTB linked into the
 	  kernel.
 
-endif # SOC_CANAAN
+endif # ARCH_CANAAN
 
 endmenu # "SoC selection"
diff --git a/arch/riscv/Makefile b/arch/riscv/Makefile
index 82153960ac00..7123511d977c 100644
--- a/arch/riscv/Makefile
+++ b/arch/riscv/Makefile
@@ -134,7 +134,7 @@ endif
 endif
 
 ifneq ($(CONFIG_XIP_KERNEL),y)
-ifeq ($(CONFIG_RISCV_M_MODE)$(CONFIG_SOC_CANAAN),yy)
+ifeq ($(CONFIG_RISCV_M_MODE)$(CONFIG_ARCH_CANAAN),yy)
 KBUILD_IMAGE := $(boot)/loader.bin
 else
 ifeq ($(CONFIG_EFI_ZBOOT),)
diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
index b0ff5fbabb0c..f0d9f89054f8 100644
--- a/arch/riscv/boot/dts/Makefile
+++ b/arch/riscv/boot/dts/Makefile
@@ -1,7 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0
+subdir-y += allwinner
 subdir-y += sifive
 subdir-y += starfive
-subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
+subdir-y += canaan
 subdir-y += microchip
 subdir-y += renesas
 
diff --git a/arch/riscv/boot/dts/allwinner/Makefile b/arch/riscv/boot/dts/allwinner/Makefile
new file mode 100644
index 000000000000..87f70b1af6b4
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-dongshan-nezha-stu.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-480p.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-720p.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-dock.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-mangopi-mq-pro.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-nezha.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1s-mangopi-mq.dtb
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-common-regulators.dtsi b/arch/riscv/boot/dts/allwinner/sun20i-common-regulators.dtsi
new file mode 100644
index 000000000000..9b03fca2444c
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-common-regulators.dtsi
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+/ {
+	reg_vcc: vcc {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_vcc_3v3: vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc>;
+	};
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc_3v3>;
+	vcc-pc-supply = <&reg_vcc_3v3>;
+	vcc-pd-supply = <&reg_vcc_3v3>;
+	vcc-pe-supply = <&reg_vcc_3v3>;
+	vcc-pf-supply = <&reg_vcc_3v3>;
+	vcc-pg-supply = <&reg_vcc_3v3>;
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-dongshan-nezha-stu.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-dongshan-nezha-stu.dts
new file mode 100644
index 000000000000..8785de3c9224
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-dongshan-nezha-stu.dts
@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+	model = "Dongshan Nezha STU";
+	compatible = "100ask,dongshan-nezha-stu", "allwinner,sun20i-d1";
+
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 2 1 GPIO_ACTIVE_HIGH>; /* PC1 */
+		};
+	};
+
+	reg_usbvbus: usbvbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usbvbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */
+		enable-active-high;
+		vin-supply = <&reg_vcc>;
+	};
+
+	/*
+	 * This regulator is PWM-controlled, but the PWM controller is not
+	 * yet supported, so fix the regulator to its default voltage.
+	 */
+	reg_vdd_cpu: vdd-cpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&reg_vcc>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-0 = <&rgmii_pe_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_vcc_3v3>;
+	status = "okay";
+};
+
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb8_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 3 21 GPIO_ACTIVE_HIGH>; /* PD21 */
+	usb0_vbus_det-gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
+	usb0_vbus-supply = <&reg_usbvbus>;
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-86-panel-480p.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-86-panel-480p.dts
new file mode 100644
index 000000000000..4df8ffb71561
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-86-panel-480p.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include "sun20i-d1-lichee-rv-86-panel.dtsi"
+
+/ {
+	model = "Sipeed Lichee RV 86 Panel (480p)";
+	compatible = "sipeed,lichee-rv-86-panel-480p", "sipeed,lichee-rv",
+		     "allwinner,sun20i-d1";
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pb0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	touchscreen@48 {
+		compatible = "focaltech,ft6236";
+		reg = <0x48>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 14 IRQ_TYPE_LEVEL_LOW>; /* PG14 */
+		iovcc-supply = <&reg_vcc_3v3>;
+		reset-gpios = <&pio 6 15 GPIO_ACTIVE_LOW>; /* PG15 */
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <480>;
+		vcc-supply = <&reg_vcc_3v3>;
+		wakeup-source;
+	};
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-86-panel-720p.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-86-panel-720p.dts
new file mode 100644
index 000000000000..1874fc05359f
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-86-panel-720p.dts
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include "sun20i-d1-lichee-rv-86-panel.dtsi"
+
+/ {
+	model = "Sipeed Lichee RV 86 Panel (720p)";
+	compatible = "sipeed,lichee-rv-86-panel-720p", "sipeed,lichee-rv",
+		     "allwinner,sun20i-d1";
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-86-panel.dtsi b/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-86-panel.dtsi
new file mode 100644
index 000000000000..6cc7dd0c1ae2
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-86-panel.dtsi
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include "sun20i-d1-lichee-rv.dts"
+
+/ {
+	aliases {
+		ethernet0 = &emac;
+		ethernet1 = &xr829;
+	};
+
+	dmic_codec: dmic-codec {
+		compatible = "dmic-codec";
+		num-channels = <2>;
+		#sound-dai-cells = <0>;
+	};
+
+	dmic-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "DMIC";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+			format = "pdm";
+			frame-master = <&link0_cpu>;
+			bitclock-master = <&link0_cpu>;
+
+			link0_cpu: cpu {
+				sound-dai = <&dmic>;
+			};
+
+			link0_codec: codec {
+				sound-dai = <&dmic_codec>;
+			};
+		};
+	};
+
+	/* PC1 is repurposed as BT_WAKE_AP */
+	/delete-node/ leds;
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&ccu CLK_FANOUT1>;
+		clock-names = "ext_clock";
+		reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+		assigned-clocks = <&ccu CLK_FANOUT1>;
+		assigned-clock-rates = <32768>;
+		pinctrl-0 = <&clk_pg11_pin>;
+		pinctrl-names = "default";
+	};
+};
+
+&dmic {
+	pinctrl-0 = <&dmic_pb11_d0_pin>, <&dmic_pe17_clk_pin>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-0 = <&rmii_pe_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&ext_rmii_phy>;
+	phy-mode = "rmii";
+	phy-supply = <&reg_vcc_3v3>;
+	status = "okay";
+};
+
+&mdio {
+	ext_rmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
+	};
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	xr829: wifi@1 {
+		reg = <1>;
+	};
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* XR829 bluetooth is connected here */
+};
+
+&usb_otg {
+	status = "disabled";
+};
+
+&usbphy {
+	/* PD20 and PD21 are repurposed for the LCD panel */
+	/delete-property/ usb0_id_det-gpios;
+	/delete-property/ usb0_vbus_det-gpios;
+	usb1_vbus-supply = <&reg_vcc>;
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-dock.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-dock.dts
new file mode 100644
index 000000000000..52b91e1affed
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv-dock.dts
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Jisheng Zhang <jszhang@kernel.org>
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/input/input.h>
+
+#include "sun20i-d1-lichee-rv.dts"
+
+/ {
+	model = "Sipeed Lichee RV Dock";
+	compatible = "sipeed,lichee-rv-dock", "sipeed,lichee-rv",
+		     "allwinner,sun20i-d1";
+
+	aliases {
+		ethernet1 = &rtl8723ds;
+	};
+
+	dmic_codec: dmic-codec {
+		compatible = "dmic-codec";
+		num-channels = <2>;
+		#sound-dai-cells = <0>;
+	};
+
+	dmic-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "DMIC";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+			format = "pdm";
+			frame-master = <&link0_cpu>;
+			bitclock-master = <&link0_cpu>;
+
+			link0_cpu: cpu {
+				sound-dai = <&dmic>;
+			};
+
+			link0_codec: codec {
+				sound-dai = <&dmic_codec>;
+			};
+		};
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+	};
+};
+
+&dmic {
+	pinctrl-0 = <&dmic_pb11_d0_pin>, <&dmic_pe17_clk_pin>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	rtl8723ds: wifi@1 {
+		reg = <1>;
+	};
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723ds-bt";
+		device-wake-gpios = <&pio 6 15 GPIO_ACTIVE_HIGH>; /* PG16 */
+		enable-gpios = <&pio 6 18 GPIO_ACTIVE_HIGH>; /* PG18 */
+		host-wake-gpios = <&pio 6 17 GPIO_ACTIVE_HIGH>; /* PG17 */
+	};
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc>;
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv.dts
new file mode 100644
index 000000000000..d60a0562a8b1
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-lichee-rv.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Jisheng Zhang <jszhang@kernel.org>
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+	model = "Sipeed Lichee RV";
+	compatible = "sipeed,lichee-rv", "allwinner,sun20i-d1";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 2 1 GPIO_ACTIVE_HIGH>; /* PC1 */
+		};
+	};
+
+	reg_vdd_cpu: vdd-cpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu";
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		vin-supply = <&reg_vcc>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&mmc0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb8_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 3 21 GPIO_ACTIVE_HIGH>; /* PD21 */
+	usb0_vbus_det-gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
+	usb0_vbus-supply = <&reg_vcc>;
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
new file mode 100644
index 000000000000..f2e07043afb3
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+	model = "MangoPi MQ Pro";
+	compatible = "widora,mangopi-mq-pro", "allwinner,sun20i-d1";
+
+	aliases {
+		ethernet0 = &rtl8723ds;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */
+		};
+	};
+
+	reg_avdd2v8: avdd2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_dvdd: dvdd {
+		compatible = "regulator-fixed";
+		regulator-name = "dvdd";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_vdd_cpu: vdd-cpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&reg_vcc>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 17 GPIO_ACTIVE_LOW>; /* PG17 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	rtl8723ds: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pe-supply = <&reg_avdd2v8>;
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb8_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723ds-bt";
+		device-wake-gpios = <&pio 6 18 GPIO_ACTIVE_HIGH>; /* PG18 */
+		enable-gpios = <&pio 6 15 GPIO_ACTIVE_HIGH>; /* PG15 */
+		host-wake-gpios = <&pio 6 14 GPIO_ACTIVE_HIGH>; /* PG14 */
+	};
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc>;
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
new file mode 100644
index 000000000000..a0769185be97
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+	model = "Allwinner D1 Nezha";
+	compatible = "allwinner,d1-nezha", "allwinner,sun20i-d1";
+
+	aliases {
+		ethernet0 = &emac;
+		ethernet1 = &xr829;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_usbvbus: usbvbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usbvbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */
+		enable-active-high;
+		vin-supply = <&reg_vcc>;
+	};
+
+	/*
+	 * This regulator is PWM-controlled, but the PWM controller is not
+	 * yet supported, so fix the regulator to its default voltage.
+	 */
+	reg_vdd_cpu: vdd-cpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&reg_vcc>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-0 = <&rgmii_pe_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_vcc_3v3>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pb0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	pcf8574a: gpio@38 {
+		compatible = "nxp,pcf8574a";
+		reg = <0x38>;
+		interrupt-parent = <&pio>;
+		interrupts = <1 2 IRQ_TYPE_LEVEL_LOW>; /* PB2 */
+		interrupt-controller;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+};
+
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	xr829: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb8_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* XR829 bluetooth is connected here */
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 3 21 GPIO_ACTIVE_HIGH>; /* PD21 */
+	usb0_vbus_det-gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
+	usb0_vbus-supply = <&reg_usbvbus>;
+	usb1_vbus-supply = <&reg_vcc>;
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi b/arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi
new file mode 100644
index 000000000000..97e7cbb32597
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi
@@ -0,0 +1,66 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+#include "sun20i-d1s.dtsi"
+#include "sunxi-d1-t113.dtsi"
+
+/ {
+	soc {
+		lradc: keys@2009800 {
+			compatible = "allwinner,sun20i-d1-lradc",
+				     "allwinner,sun50i-r329-lradc";
+			reg = <0x2009800 0x400>;
+			interrupts = <SOC_PERIPHERAL_IRQ(61) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_LRADC>;
+			resets = <&ccu RST_BUS_LRADC>;
+			status = "disabled";
+		};
+
+		i2s0: i2s@2032000 {
+			compatible = "allwinner,sun20i-d1-i2s",
+				     "allwinner,sun50i-r329-i2s";
+			reg = <0x2032000 0x1000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(26) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S0>,
+				 <&ccu CLK_I2S0>;
+			clock-names = "apb", "mod";
+			resets = <&ccu RST_BUS_I2S0>;
+			dmas = <&dma 3>, <&dma 3>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+			#sound-dai-cells = <0>;
+		};
+	};
+};
+
+&pio {
+	/omit-if-no-ref/
+	dmic_pb11_d0_pin: dmic-pb11-d0-pin {
+		pins = "PB11";
+		function = "dmic";
+	};
+
+	/omit-if-no-ref/
+	dmic_pe17_clk_pin: dmic-pe17-clk-pin {
+		pins = "PE17";
+		function = "dmic";
+	};
+
+	/omit-if-no-ref/
+	i2c0_pb10_pins: i2c0-pb10-pins {
+		pins = "PB10", "PB11";
+		function = "i2c0";
+	};
+
+	/omit-if-no-ref/
+	i2c2_pb0_pins: i2c2-pb0-pins {
+		pins = "PB0", "PB1";
+		function = "i2c2";
+	};
+
+	/omit-if-no-ref/
+	uart0_pb8_pins: uart0-pb8-pins {
+		pins = "PB8", "PB9";
+		function = "uart0";
+	};
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1s-mangopi-mq.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1s-mangopi-mq.dts
new file mode 100644
index 000000000000..e6d924f671fd
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1s-mangopi-mq.dts
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/dts-v1/;
+
+#include "sun20i-d1s.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+	model = "MangoPi MQ";
+	compatible = "widora,mangopi-mq", "allwinner,sun20i-d1s";
+
+	aliases {
+		ethernet0 = &rtl8189ftv;
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 3 22 GPIO_ACTIVE_LOW>; /* PD22 */
+		};
+	};
+
+	reg_avdd2v8: avdd2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_dvdd: dvdd {
+		compatible = "regulator-fixed";
+		regulator-name = "dvdd";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_vcc_core: vcc-core {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-core";
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		vin-supply = <&reg_vcc>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	rtl8189ftv: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pe-supply = <&reg_avdd2v8>;
+};
+
+&uart3 {
+	pinctrl-0 = <&uart3_pb_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc>;
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi b/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi
new file mode 100644
index 000000000000..8275630af977
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+#define SOC_PERIPHERAL_IRQ(nr)	(nr + 16)
+
+#include "sunxi-d1s-t113.dtsi"
+
+/ {
+	cpus {
+		timebase-frequency = <24000000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "thead,c906", "riscv";
+			device_type = "cpu";
+			reg = <0>;
+			clocks = <&ccu CLK_RISCV>;
+			d-cache-block-size = <64>;
+			d-cache-sets = <256>;
+			d-cache-size = <32768>;
+			i-cache-block-size = <64>;
+			i-cache-sets = <128>;
+			i-cache-size = <32768>;
+			mmu-type = "riscv,sv39";
+			operating-points-v2 = <&opp_table_cpu>;
+			riscv,isa = "rv64imafdc";
+			#cooling-cells = <2>;
+
+			cpu0_intc: interrupt-controller {
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+			};
+		};
+	};
+
+	opp_table_cpu: opp-table-cpu {
+		compatible = "operating-points-v2";
+
+		opp-408000000 {
+			opp-hz = /bits/ 64 <408000000>;
+			opp-microvolt = <900000 900000 1100000>;
+		};
+
+		opp-1080000000 {
+			opp-hz = /bits/ 64 <1008000000>;
+			opp-microvolt = <900000 900000 1100000>;
+		};
+	};
+
+	soc {
+		interrupt-parent = <&plic>;
+
+		riscv_wdt: watchdog@6011000 {
+			compatible = "allwinner,sun20i-d1-wdt";
+			reg = <0x6011000 0x20>;
+			interrupts = <SOC_PERIPHERAL_IRQ(131) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&dcxo>, <&rtc CLK_OSC32K>;
+			clock-names = "hosc", "losc";
+		};
+
+		plic: interrupt-controller@10000000 {
+			compatible = "allwinner,sun20i-d1-plic",
+				     "thead,c900-plic";
+			reg = <0x10000000 0x4000000>;
+			interrupts-extended = <&cpu0_intc 11>,
+					      <&cpu0_intc 9>;
+			interrupt-controller;
+			riscv,ndev = <175>;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi b/arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi
new file mode 100644
index 000000000000..b7156123df54
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+/ {
+	soc {
+		dsp_wdt: watchdog@1700400 {
+			compatible = "allwinner,sun20i-d1-wdt";
+			reg = <0x1700400 0x20>;
+			interrupts = <SOC_PERIPHERAL_IRQ(122) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&dcxo>, <&rtc CLK_OSC32K>;
+			clock-names = "hosc", "losc";
+			status = "reserved";
+		};
+	};
+};
diff --git a/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
new file mode 100644
index 000000000000..6fadcee7800f
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
@@ -0,0 +1,834 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/clock/sun6i-rtc.h>
+#include <dt-bindings/clock/sun8i-de2.h>
+#include <dt-bindings/clock/sun8i-tcon-top.h>
+#include <dt-bindings/clock/sun20i-d1-ccu.h>
+#include <dt-bindings/clock/sun20i-d1-r-ccu.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/reset/sun8i-de2.h>
+#include <dt-bindings/reset/sun20i-d1-ccu.h>
+#include <dt-bindings/reset/sun20i-d1-r-ccu.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	dcxo: dcxo-clk {
+		compatible = "fixed-clock";
+		clock-output-names = "dcxo";
+		#clock-cells = <0>;
+	};
+
+	de: display-engine {
+		compatible = "allwinner,sun20i-d1-display-engine";
+		allwinner,pipelines = <&mixer0>, <&mixer1>;
+		status = "disabled";
+	};
+
+	soc {
+		compatible = "simple-bus";
+		ranges;
+		dma-noncoherent;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		pio: pinctrl@2000000 {
+			compatible = "allwinner,sun20i-d1-pinctrl";
+			reg = <0x2000000 0x800>;
+			interrupts = <SOC_PERIPHERAL_IRQ(69) IRQ_TYPE_LEVEL_HIGH>,
+				     <SOC_PERIPHERAL_IRQ(71) IRQ_TYPE_LEVEL_HIGH>,
+				     <SOC_PERIPHERAL_IRQ(73) IRQ_TYPE_LEVEL_HIGH>,
+				     <SOC_PERIPHERAL_IRQ(75) IRQ_TYPE_LEVEL_HIGH>,
+				     <SOC_PERIPHERAL_IRQ(77) IRQ_TYPE_LEVEL_HIGH>,
+				     <SOC_PERIPHERAL_IRQ(79) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_APB0>,
+				 <&dcxo>,
+				 <&rtc CLK_OSC32K>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			interrupt-controller;
+			#gpio-cells = <3>;
+			#interrupt-cells = <3>;
+
+			/omit-if-no-ref/
+			clk_pg11_pin: clk-pg11-pin {
+				pins = "PG11";
+				function = "clk";
+			};
+
+			/omit-if-no-ref/
+			dsi_4lane_pins: dsi-4lane-pins {
+				pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5",
+				       "PD6", "PD7", "PD8", "PD9";
+				drive-strength = <30>;
+				function = "dsi";
+			};
+
+			/omit-if-no-ref/
+			lcd_rgb666_pins: lcd-rgb666-pins {
+				pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5",
+				       "PD6", "PD7", "PD8", "PD9", "PD10", "PD11",
+				       "PD12", "PD13", "PD14", "PD15", "PD16", "PD17",
+				       "PD18", "PD19", "PD20", "PD21";
+				function = "lcd0";
+			};
+
+			/omit-if-no-ref/
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5";
+				function = "mmc0";
+			};
+
+			/omit-if-no-ref/
+			mmc1_pins: mmc1-pins {
+				pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5";
+				function = "mmc1";
+			};
+
+			/omit-if-no-ref/
+			mmc2_pins: mmc2-pins {
+				pins = "PC2", "PC3", "PC4", "PC5", "PC6", "PC7";
+				function = "mmc2";
+			};
+
+			/omit-if-no-ref/
+			rgmii_pe_pins: rgmii-pe-pins {
+				pins = "PE0", "PE1", "PE2", "PE3", "PE4",
+				       "PE5", "PE6", "PE7", "PE8", "PE9",
+				       "PE11", "PE12", "PE13", "PE14", "PE15";
+				function = "emac";
+			};
+
+			/omit-if-no-ref/
+			rmii_pe_pins: rmii-pe-pins {
+				pins = "PE0", "PE1", "PE2", "PE3", "PE4",
+				       "PE5", "PE6", "PE7", "PE8", "PE9";
+				function = "emac";
+			};
+
+			/omit-if-no-ref/
+			uart1_pg6_pins: uart1-pg6-pins {
+				pins = "PG6", "PG7";
+				function = "uart1";
+			};
+
+			/omit-if-no-ref/
+			uart1_pg8_rts_cts_pins: uart1-pg8-rts-cts-pins {
+				pins = "PG8", "PG9";
+				function = "uart1";
+			};
+
+			/omit-if-no-ref/
+			uart3_pb_pins: uart3-pb-pins {
+				pins = "PB6", "PB7";
+				function = "uart3";
+			};
+		};
+
+		ccu: clock-controller@2001000 {
+			compatible = "allwinner,sun20i-d1-ccu";
+			reg = <0x2001000 0x1000>;
+			clocks = <&dcxo>,
+				 <&rtc CLK_OSC32K>,
+				 <&rtc CLK_IOSC>;
+			clock-names = "hosc", "losc", "iosc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		dmic: dmic@2031000 {
+			compatible = "allwinner,sun20i-d1-dmic",
+				     "allwinner,sun50i-h6-dmic";
+			reg = <0x2031000 0x400>;
+			interrupts = <SOC_PERIPHERAL_IRQ(24) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DMIC>,
+				 <&ccu CLK_DMIC>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_DMIC>;
+			dmas = <&dma 8>;
+			dma-names = "rx";
+			status = "disabled";
+			#sound-dai-cells = <0>;
+		};
+
+		i2s1: i2s@2033000 {
+			compatible = "allwinner,sun20i-d1-i2s",
+				     "allwinner,sun50i-r329-i2s";
+			reg = <0x2033000 0x1000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(27) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S1>,
+				 <&ccu CLK_I2S1>;
+			clock-names = "apb", "mod";
+			resets = <&ccu RST_BUS_I2S1>;
+			dmas = <&dma 4>, <&dma 4>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+			#sound-dai-cells = <0>;
+		};
+
+		i2s2: i2s@2034000 {
+			compatible = "allwinner,sun20i-d1-i2s",
+				     "allwinner,sun50i-r329-i2s";
+			reg = <0x2034000 0x1000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(28) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S2>,
+				 <&ccu CLK_I2S2>;
+			clock-names = "apb", "mod";
+			resets = <&ccu RST_BUS_I2S2>;
+			dmas = <&dma 5>, <&dma 5>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+			#sound-dai-cells = <0>;
+		};
+
+		timer: timer@2050000 {
+			compatible = "allwinner,sun20i-d1-timer",
+				     "allwinner,sun8i-a23-timer";
+			reg = <0x2050000 0xa0>;
+			interrupts = <SOC_PERIPHERAL_IRQ(59) IRQ_TYPE_LEVEL_HIGH>,
+				     <SOC_PERIPHERAL_IRQ(60) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&dcxo>;
+		};
+
+		wdt: watchdog@20500a0 {
+			compatible = "allwinner,sun20i-d1-wdt-reset",
+				     "allwinner,sun20i-d1-wdt";
+			reg = <0x20500a0 0x20>;
+			interrupts = <SOC_PERIPHERAL_IRQ(63) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&dcxo>, <&rtc CLK_OSC32K>;
+			clock-names = "hosc", "losc";
+			status = "reserved";
+		};
+
+		uart0: serial@2500000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x2500000 0x400>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			interrupts = <SOC_PERIPHERAL_IRQ(2) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
+			dmas = <&dma 14>, <&dma 14>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart1: serial@2500400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x2500400 0x400>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			interrupts = <SOC_PERIPHERAL_IRQ(3) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
+			dmas = <&dma 15>, <&dma 15>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart2: serial@2500800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x2500800 0x400>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			interrupts = <SOC_PERIPHERAL_IRQ(4) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
+			dmas = <&dma 16>, <&dma 16>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart3: serial@2500c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x2500c00 0x400>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			interrupts = <SOC_PERIPHERAL_IRQ(5) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_UART3>;
+			resets = <&ccu RST_BUS_UART3>;
+			dmas = <&dma 17>, <&dma 17>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart4: serial@2501000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x2501000 0x400>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			interrupts = <SOC_PERIPHERAL_IRQ(6) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_UART4>;
+			resets = <&ccu RST_BUS_UART4>;
+			dmas = <&dma 18>, <&dma 18>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart5: serial@2501400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x2501400 0x400>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			interrupts = <SOC_PERIPHERAL_IRQ(7) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_UART5>;
+			resets = <&ccu RST_BUS_UART5>;
+			dmas = <&dma 19>, <&dma 19>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2c0: i2c@2502000 {
+			compatible = "allwinner,sun20i-d1-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x2502000 0x400>;
+			interrupts = <SOC_PERIPHERAL_IRQ(9) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			dmas = <&dma 43>, <&dma 43>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@2502400 {
+			compatible = "allwinner,sun20i-d1-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x2502400 0x400>;
+			interrupts = <SOC_PERIPHERAL_IRQ(10) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			dmas = <&dma 44>, <&dma 44>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@2502800 {
+			compatible = "allwinner,sun20i-d1-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x2502800 0x400>;
+			interrupts = <SOC_PERIPHERAL_IRQ(11) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			dmas = <&dma 45>, <&dma 45>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c3: i2c@2502c00 {
+			compatible = "allwinner,sun20i-d1-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x2502c00 0x400>;
+			interrupts = <SOC_PERIPHERAL_IRQ(12) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C3>;
+			resets = <&ccu RST_BUS_I2C3>;
+			dmas = <&dma 46>, <&dma 46>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		syscon: syscon@3000000 {
+			compatible = "allwinner,sun20i-d1-system-control";
+			reg = <0x3000000 0x1000>;
+			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+
+		dma: dma-controller@3002000 {
+			compatible = "allwinner,sun20i-d1-dma";
+			reg = <0x3002000 0x1000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(50) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
+			clock-names = "bus", "mbus";
+			resets = <&ccu RST_BUS_DMA>;
+			dma-channels = <16>;
+			dma-requests = <48>;
+			#dma-cells = <1>;
+		};
+
+		sid: efuse@3006000 {
+			compatible = "allwinner,sun20i-d1-sid";
+			reg = <0x3006000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+
+		mbus: dram-controller@3102000 {
+			compatible = "allwinner,sun20i-d1-mbus";
+			reg = <0x3102000 0x1000>,
+			      <0x3103000 0x1000>;
+			reg-names = "mbus", "dram";
+			interrupts = <SOC_PERIPHERAL_IRQ(43) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_MBUS>,
+				 <&ccu CLK_DRAM>,
+				 <&ccu CLK_BUS_DRAM>;
+			clock-names = "mbus", "dram", "bus";
+			dma-ranges = <0 0x40000000 0x80000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#interconnect-cells = <1>;
+		};
+
+		mmc0: mmc@4020000 {
+			compatible = "allwinner,sun20i-d1-mmc";
+			reg = <0x4020000 0x1000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(40) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			cap-sd-highspeed;
+			max-frequency = <150000000>;
+			no-mmc;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@4021000 {
+			compatible = "allwinner,sun20i-d1-mmc";
+			reg = <0x4021000 0x1000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(41) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			cap-sd-highspeed;
+			max-frequency = <150000000>;
+			no-mmc;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@4022000 {
+			compatible = "allwinner,sun20i-d1-emmc",
+				     "allwinner,sun50i-a100-emmc";
+			reg = <0x4022000 0x1000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(42) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			cap-mmc-highspeed;
+			max-frequency = <150000000>;
+			mmc-ddr-1_8v;
+			mmc-ddr-3_3v;
+			no-sd;
+			no-sdio;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		usb_otg: usb@4100000 {
+			compatible = "allwinner,sun20i-d1-musb",
+				     "allwinner,sun8i-a33-musb";
+			reg = <0x4100000 0x400>;
+			interrupts = <SOC_PERIPHERAL_IRQ(29) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mc";
+			clocks = <&ccu CLK_BUS_OTG>;
+			resets = <&ccu RST_BUS_OTG>;
+			extcon = <&usbphy 0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		usbphy: phy@4100400 {
+			compatible = "allwinner,sun20i-d1-usb-phy";
+			reg = <0x4100400 0x100>,
+			      <0x4101800 0x100>,
+			      <0x4200800 0x100>;
+			reg-names = "phy_ctrl",
+				    "pmu0",
+				    "pmu1";
+			clocks = <&dcxo>,
+				 <&dcxo>;
+			clock-names = "usb0_phy",
+				      "usb1_phy";
+			resets = <&ccu RST_USB_PHY0>,
+				 <&ccu RST_USB_PHY1>;
+			reset-names = "usb0_reset",
+				      "usb1_reset";
+			status = "disabled";
+			#phy-cells = <1>;
+		};
+
+		ehci0: usb@4101000 {
+			compatible = "allwinner,sun20i-d1-ehci",
+				     "generic-ehci";
+			reg = <0x4101000 0x100>;
+			interrupts = <SOC_PERIPHERAL_IRQ(30) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI0>,
+				 <&ccu CLK_BUS_EHCI0>,
+				 <&ccu CLK_USB_OHCI0>;
+			resets = <&ccu RST_BUS_OHCI0>,
+				 <&ccu RST_BUS_EHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci0: usb@4101400 {
+			compatible = "allwinner,sun20i-d1-ohci",
+				     "generic-ohci";
+			reg = <0x4101400 0x100>;
+			interrupts = <SOC_PERIPHERAL_IRQ(31) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI0>,
+				 <&ccu CLK_USB_OHCI0>;
+			resets = <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ehci1: usb@4200000 {
+			compatible = "allwinner,sun20i-d1-ehci",
+				     "generic-ehci";
+			reg = <0x4200000 0x100>;
+			interrupts = <SOC_PERIPHERAL_IRQ(33) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI1>,
+				 <&ccu CLK_BUS_EHCI1>,
+				 <&ccu CLK_USB_OHCI1>;
+			resets = <&ccu RST_BUS_OHCI1>,
+				 <&ccu RST_BUS_EHCI1>;
+			phys = <&usbphy 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci1: usb@4200400 {
+			compatible = "allwinner,sun20i-d1-ohci",
+				     "generic-ohci";
+			reg = <0x4200400 0x100>;
+			interrupts = <SOC_PERIPHERAL_IRQ(34) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI1>,
+				 <&ccu CLK_USB_OHCI1>;
+			resets = <&ccu RST_BUS_OHCI1>;
+			phys = <&usbphy 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		emac: ethernet@4500000 {
+			compatible = "allwinner,sun20i-d1-emac",
+				     "allwinner,sun50i-a64-emac";
+			reg = <0x4500000 0x10000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(46) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks = <&ccu CLK_BUS_EMAC>;
+			clock-names = "stmmaceth";
+			resets = <&ccu RST_BUS_EMAC>;
+			reset-names = "stmmaceth";
+			syscon = <&syscon>;
+			status = "disabled";
+
+			mdio: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		display_clocks: clock-controller@5000000 {
+			compatible = "allwinner,sun20i-d1-de2-clk",
+				     "allwinner,sun50i-h5-de2-clk";
+			reg = <0x5000000 0x10000>;
+			clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_DE>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		mixer0: mixer@5100000 {
+			compatible = "allwinner,sun20i-d1-de2-mixer-0";
+			reg = <0x5100000 0x100000>;
+			clocks = <&display_clocks CLK_BUS_MIXER0>,
+				 <&display_clocks CLK_MIXER0>;
+			clock-names = "bus", "mod";
+			resets = <&display_clocks RST_MIXER0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mixer0_out: port@1 {
+					reg = <1>;
+
+					mixer0_out_tcon_top_mixer0: endpoint {
+						remote-endpoint = <&tcon_top_mixer0_in_mixer0>;
+					};
+				};
+			};
+		};
+
+		mixer1: mixer@5200000 {
+			compatible = "allwinner,sun20i-d1-de2-mixer-1";
+			reg = <0x5200000 0x100000>;
+			clocks = <&display_clocks CLK_BUS_MIXER1>,
+				 <&display_clocks CLK_MIXER1>;
+			clock-names = "bus", "mod";
+			resets = <&display_clocks RST_MIXER1>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mixer1_out: port@1 {
+					reg = <1>;
+
+					mixer1_out_tcon_top_mixer1: endpoint {
+						remote-endpoint = <&tcon_top_mixer1_in_mixer1>;
+					};
+				};
+			};
+		};
+
+		dsi: dsi@5450000 {
+			compatible = "allwinner,sun20i-d1-mipi-dsi",
+				     "allwinner,sun50i-a100-mipi-dsi";
+			reg = <0x5450000 0x1000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(92) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_MIPI_DSI>,
+				 <&tcon_top CLK_TCON_TOP_DSI>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_MIPI_DSI>;
+			phys = <&dphy>;
+			phy-names = "dphy";
+			status = "disabled";
+
+			port {
+				dsi_in_tcon_lcd0: endpoint {
+					remote-endpoint = <&tcon_lcd0_out_dsi>;
+				};
+			};
+		};
+
+		dphy: phy@5451000 {
+			compatible = "allwinner,sun20i-d1-mipi-dphy",
+				     "allwinner,sun50i-a100-mipi-dphy";
+			reg = <0x5451000 0x1000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(92) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_MIPI_DSI>,
+				 <&ccu CLK_MIPI_DSI>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_MIPI_DSI>;
+			#phy-cells = <0>;
+		};
+
+		tcon_top: tcon-top@5460000 {
+			compatible = "allwinner,sun20i-d1-tcon-top";
+			reg = <0x5460000 0x1000>;
+			clocks = <&ccu CLK_BUS_DPSS_TOP>,
+				 <&ccu CLK_TCON_TV>,
+				 <&ccu CLK_TVE>,
+				 <&ccu CLK_TCON_LCD0>;
+			clock-names = "bus", "tcon-tv0", "tve0", "dsi";
+			clock-output-names = "tcon-top-tv0", "tcon-top-dsi";
+			resets = <&ccu RST_BUS_DPSS_TOP>;
+			#clock-cells = <1>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon_top_mixer0_in: port@0 {
+					reg = <0>;
+
+					tcon_top_mixer0_in_mixer0: endpoint {
+						remote-endpoint = <&mixer0_out_tcon_top_mixer0>;
+					};
+				};
+
+				tcon_top_mixer0_out: port@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					tcon_top_mixer0_out_tcon_lcd0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon_lcd0_in_tcon_top_mixer0>;
+					};
+
+					tcon_top_mixer0_out_tcon_tv0: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&tcon_tv0_in_tcon_top_mixer0>;
+					};
+				};
+
+				tcon_top_mixer1_in: port@2 {
+					reg = <2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					tcon_top_mixer1_in_mixer1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&mixer1_out_tcon_top_mixer1>;
+					};
+				};
+
+				tcon_top_mixer1_out: port@3 {
+					reg = <3>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					tcon_top_mixer1_out_tcon_lcd0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon_lcd0_in_tcon_top_mixer1>;
+					};
+
+					tcon_top_mixer1_out_tcon_tv0: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&tcon_tv0_in_tcon_top_mixer1>;
+					};
+				};
+
+				tcon_top_hdmi_in: port@4 {
+					reg = <4>;
+
+					tcon_top_hdmi_in_tcon_tv0: endpoint {
+						remote-endpoint = <&tcon_tv0_out_tcon_top_hdmi>;
+					};
+				};
+
+				tcon_top_hdmi_out: port@5 {
+					reg = <5>;
+				};
+			};
+		};
+
+		tcon_lcd0: lcd-controller@5461000 {
+			compatible = "allwinner,sun20i-d1-tcon-lcd";
+			reg = <0x5461000 0x1000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(90) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_TCON_LCD0>,
+				 <&ccu CLK_TCON_LCD0>;
+			clock-names = "ahb", "tcon-ch0";
+			clock-output-names = "tcon-pixel-clock";
+			resets = <&ccu RST_BUS_TCON_LCD0>,
+				 <&ccu RST_BUS_LVDS0>;
+			reset-names = "lcd", "lvds";
+			#clock-cells = <0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon_lcd0_in: port@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					tcon_lcd0_in_tcon_top_mixer0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon_top_mixer0_out_tcon_lcd0>;
+					};
+
+					tcon_lcd0_in_tcon_top_mixer1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&tcon_top_mixer1_out_tcon_lcd0>;
+					};
+				};
+
+				tcon_lcd0_out: port@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					tcon_lcd0_out_dsi: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&dsi_in_tcon_lcd0>;
+					};
+				};
+			};
+		};
+
+		tcon_tv0: lcd-controller@5470000 {
+			compatible = "allwinner,sun20i-d1-tcon-tv";
+			reg = <0x5470000 0x1000>;
+			interrupts = <SOC_PERIPHERAL_IRQ(91) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_TCON_TV>,
+				 <&tcon_top CLK_TCON_TOP_TV0>;
+			clock-names = "ahb", "tcon-ch1";
+			resets = <&ccu RST_BUS_TCON_TV>;
+			reset-names = "lcd";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon_tv0_in: port@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					tcon_tv0_in_tcon_top_mixer0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon_top_mixer0_out_tcon_tv0>;
+					};
+
+					tcon_tv0_in_tcon_top_mixer1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&tcon_top_mixer1_out_tcon_tv0>;
+					};
+				};
+
+				tcon_tv0_out: port@1 {
+					reg = <1>;
+
+					tcon_tv0_out_tcon_top_hdmi: endpoint {
+						remote-endpoint = <&tcon_top_hdmi_in_tcon_tv0>;
+					};
+				};
+			};
+		};
+
+		ppu: power-controller@7001000 {
+			compatible = "allwinner,sun20i-d1-ppu";
+			reg = <0x7001000 0x1000>;
+			clocks = <&r_ccu CLK_BUS_R_PPU>;
+			resets = <&r_ccu RST_BUS_R_PPU>;
+			#power-domain-cells = <1>;
+		};
+
+		r_ccu: clock-controller@7010000 {
+			compatible = "allwinner,sun20i-d1-r-ccu";
+			reg = <0x7010000 0x400>;
+			clocks = <&dcxo>,
+				 <&rtc CLK_OSC32K>,
+				 <&rtc CLK_IOSC>,
+				 <&ccu CLK_PLL_PERIPH0_DIV3>;
+			clock-names = "hosc", "losc", "iosc", "pll-periph";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		rtc: rtc@7090000 {
+			compatible = "allwinner,sun20i-d1-rtc",
+				     "allwinner,sun50i-r329-rtc";
+			reg = <0x7090000 0x400>;
+			interrupts = <SOC_PERIPHERAL_IRQ(144) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_BUS_R_RTC>,
+				 <&dcxo>,
+				 <&r_ccu CLK_R_AHB>;
+			clock-names = "bus", "hosc", "ahb";
+			#clock-cells = <1>;
+		};
+	};
+};
diff --git a/arch/riscv/boot/dts/canaan/Makefile b/arch/riscv/boot/dts/canaan/Makefile
index befe4eb7527b..520623264c87 100644
--- a/arch/riscv/boot/dts/canaan/Makefile
+++ b/arch/riscv/boot/dts/canaan/Makefile
@@ -1,9 +1,9 @@
 # SPDX-License-Identifier: GPL-2.0
-dtb-$(CONFIG_SOC_CANAAN) += canaan_kd233.dtb
-dtb-$(CONFIG_SOC_CANAAN) += k210_generic.dtb
-dtb-$(CONFIG_SOC_CANAAN) += sipeed_maix_bit.dtb
-dtb-$(CONFIG_SOC_CANAAN) += sipeed_maix_dock.dtb
-dtb-$(CONFIG_SOC_CANAAN) += sipeed_maix_go.dtb
-dtb-$(CONFIG_SOC_CANAAN) += sipeed_maixduino.dtb
+dtb-$(CONFIG_ARCH_CANAAN) += canaan_kd233.dtb
+dtb-$(CONFIG_ARCH_CANAAN) += k210_generic.dtb
+dtb-$(CONFIG_ARCH_CANAAN) += sipeed_maix_bit.dtb
+dtb-$(CONFIG_ARCH_CANAAN) += sipeed_maix_dock.dtb
+dtb-$(CONFIG_ARCH_CANAAN) += sipeed_maix_go.dtb
+dtb-$(CONFIG_ARCH_CANAAN) += sipeed_maixduino.dtb
 
-obj-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += $(addsuffix .dtb.o, $(CONFIG_SOC_CANAAN_K210_DTB_SOURCE))
+obj-$(CONFIG_ARCH_CANAAN_K210_DTB_BUILTIN) += $(addsuffix .dtb.o, $(CONFIG_ARCH_CANAAN_K210_DTB_SOURCE))
diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
index 7427a20934f3..45adc4926e79 100644
--- a/arch/riscv/boot/dts/microchip/Makefile
+++ b/arch/riscv/boot/dts/microchip/Makefile
@@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
-dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-icicle-kit.dtb
-dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-m100pfsevp.dtb
-dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-polarberry.dtb
-dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-sev-kit.dtb
+dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-icicle-kit.dtb
+dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-m100pfsevp.dtb
+dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-polarberry.dtb
+dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-sev-kit.dtb
+dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-tysom-m.dtb
 obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
diff --git a/arch/riscv/boot/dts/microchip/mpfs-tysom-m-fabric.dtsi b/arch/riscv/boot/dts/microchip/mpfs-tysom-m-fabric.dtsi
new file mode 100644
index 000000000000..98f642e83ad4
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/mpfs-tysom-m-fabric.dtsi
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2022 Microchip Technology Inc */
+
+// #include "dt-bindings/mailbox/miv-ihc.h"
+
+/ {
+	fabric_clk3: fabric-clk3 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <62500000>;
+	};
+
+	fabric_clk1: fabric-clk1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
+};
diff --git a/arch/riscv/boot/dts/microchip/mpfs-tysom-m.dts b/arch/riscv/boot/dts/microchip/mpfs-tysom-m.dts
new file mode 100644
index 000000000000..e0797c7e1b35
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/mpfs-tysom-m.dts
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Original all-in-one devicetree:
+ * Copyright (C) 2020-2022 - Aldec
+ * Rewritten to use includes:
+ * Copyright (C) 2022 - Conor Dooley <conor.dooley@microchip.com>
+ */
+
+/dts-v1/;
+
+#include "mpfs.dtsi"
+#include "mpfs-tysom-m-fabric.dtsi"
+
+/* Clock frequency (in Hz) of the rtcclk */
+#define MTIMER_FREQ		1000000
+
+/ {
+	model = "Aldec TySOM-M-MPFS250T-REV2";
+	compatible = "aldec,tysom-m-mpfs250t-rev2", "microchip,mpfs";
+
+	aliases {
+		ethernet0 = &mac0;
+		ethernet1 = &mac1;
+		serial0 = &mmuart0;
+		serial1 = &mmuart1;
+		serial2 = &mmuart2;
+		serial3 = &mmuart3;
+		serial4 = &mmuart4;
+		gpio0 = &gpio0;
+		gpio1 = &gpio2;
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+
+	cpus {
+		timebase-frequency = <MTIMER_FREQ>;
+	};
+
+	ddrc_cache_lo: memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x0 0x30000000>;
+		status = "okay";
+	};
+
+	ddrc_cache_hi: memory@1000000000 {
+		device_type = "memory";
+		reg = <0x10 0x00000000 0x0 0x40000000>;
+		status = "okay";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		status = "okay";
+
+		led0 {
+			gpios = <&gpio1 23 1>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+	hwmon: hwmon@45 {
+		status = "okay";
+		compatible = "ti,ina219";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+};
+
+&gpio1 {
+	interrupts = <27>, <28>, <29>, <30>,
+		     <31>, <32>, <33>, <47>,
+		     <35>, <36>, <37>, <38>,
+		     <39>, <40>, <41>, <42>,
+		     <43>, <44>, <45>, <46>,
+		     <47>, <48>, <49>, <50>;
+	status = "okay";
+};
+
+&mac0 {
+	status = "okay";
+	phy-mode = "gmii";
+	phy-handle = <&phy0>;
+
+};
+
+&mac1 {
+	status = "okay";
+	phy-mode = "gmii";
+	phy-handle = <&phy1>;
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&mbox {
+	status = "okay";
+};
+
+&mmc {
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	no-1-8-v;
+	disable-wp;
+	status = "okay";
+};
+
+&mmuart1 {
+	status = "okay";
+};
+
+&mmuart2 {
+	status = "okay";
+};
+
+&mmuart3 {
+	status = "okay";
+};
+
+&mmuart4 {
+	status = "okay";
+};
+
+&refclk {
+	clock-frequency = <125000000>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+	flash@0 {
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
+		reg = <0x0>;
+		spi-max-frequency = <10000000>;
+	};
+};
+
+&syscontroller {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "host";
+};
diff --git a/arch/riscv/boot/dts/renesas/rzfive-smarc-som.dtsi b/arch/riscv/boot/dts/renesas/rzfive-smarc-som.dtsi
index 2b7672bc4b52..d6f18754eb5d 100644
--- a/arch/riscv/boot/dts/renesas/rzfive-smarc-som.dtsi
+++ b/arch/riscv/boot/dts/renesas/rzfive-smarc-som.dtsi
@@ -24,24 +24,22 @@
 
 &eth0 {
 	status = "disabled";
-};
 
-&eth1 {
-	status = "disabled";
+	phy0: ethernet-phy@7 {
+		/delete-property/ interrupt-parent;
+		/delete-property/ interrupts;
+	};
 };
 
-&ostm1 {
+&eth1 {
 	status = "disabled";
-};
 
-&ostm2 {
-	status = "disabled";
+	phy1: ethernet-phy@7 {
+		/delete-property/ interrupt-parent;
+		/delete-property/ interrupts;
+	};
 };
 
 &sdhi0 {
 	status = "disabled";
 };
-
-&wdt0 {
-	status = "disabled";
-};
diff --git a/arch/riscv/boot/dts/sifive/Makefile b/arch/riscv/boot/dts/sifive/Makefile
index d90e4eb0ade8..6a5fbd4ed96a 100644
--- a/arch/riscv/boot/dts/sifive/Makefile
+++ b/arch/riscv/boot/dts/sifive/Makefile
@@ -1,4 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0
-dtb-$(CONFIG_SOC_SIFIVE) += hifive-unleashed-a00.dtb \
-			    hifive-unmatched-a00.dtb
+dtb-$(CONFIG_ARCH_SIFIVE) += hifive-unleashed-a00.dtb \
+			     hifive-unmatched-a00.dtb
 obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile
index 039c143cba33..7b00a48580ca 100644
--- a/arch/riscv/boot/dts/starfive/Makefile
+++ b/arch/riscv/boot/dts/starfive/Makefile
@@ -1,2 +1,2 @@
 # SPDX-License-Identifier: GPL-2.0
-dtb-$(CONFIG_SOC_STARFIVE) += jh7100-beaglev-starlight.dtb jh7100-starfive-visionfive-v1.dtb
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-beaglev-starlight.dtb jh7100-starfive-visionfive-v1.dtb