drm/amd/powerplay: and smc dpm info struct for sienna_cichlid

And atom_smc_dpm_info_v4_9 struct for sienna_cichlid use.

Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

1 files changed, 123 insertions, 0 deletions

diff --git a/drivers/gpu/drm/amd/include/atomfirmware.h b/drivers/gpu/drm/amd/include/atomfirmware.h
index f7e98855cac7..b852248b2da8 100644
--- a/drivers/gpu/drm/amd/include/atomfirmware.h
+++ b/drivers/gpu/drm/amd/include/atomfirmware.h
@@ -2016,6 +2016,129 @@ struct atom_smc_dpm_info_v4_7
   uint32_t     BoardReserved[5];
 };
 
+struct smudpm_i2c_controller_config_v3
+{
+  uint8_t   Enabled;
+  uint8_t   Speed;
+  uint8_t   SlaveAddress;
+  uint8_t   ControllerPort;
+  uint8_t   ControllerName;
+  uint8_t   ThermalThrotter;
+  uint8_t   I2cProtocol;
+  uint8_t   PaddingConfig;
+};
+
+struct atom_smc_dpm_info_v4_9
+{
+  struct   atom_common_table_header  table_header;
+
+  //SECTION: Gaming Clocks
+  //uint32_t     GamingClk[6];
+
+  // SECTION: I2C Control
+  struct smudpm_i2c_controller_config_v3  I2cControllers[16];     
+
+  uint8_t      GpioScl;  // GPIO Number for SCL Line, used only for CKSVII2C1
+  uint8_t      GpioSda;  // GPIO Number for SDA Line, used only for CKSVII2C1
+  uint8_t      FchUsbPdSlaveAddr; //For requesting USB PD controller S-states via FCH I2C when entering PME turn off
+  uint8_t      I2cSpare;
+
+  // SECTION: SVI2 Board Parameters
+  uint8_t      VddGfxVrMapping;   // Use VR_MAPPING* bitfields
+  uint8_t      VddSocVrMapping;   // Use VR_MAPPING* bitfields
+  uint8_t      VddMem0VrMapping;  // Use VR_MAPPING* bitfields
+  uint8_t      VddMem1VrMapping;  // Use VR_MAPPING* bitfields
+
+  uint8_t      GfxUlvPhaseSheddingMask; // set this to 1 to set PSI0/1 to 1 in ULV mode
+  uint8_t      SocUlvPhaseSheddingMask; // set this to 1 to set PSI0/1 to 1 in ULV mode
+  uint8_t      VddciUlvPhaseSheddingMask; // set this to 1 to set PSI0/1 to 1 in ULV mode
+  uint8_t      MvddUlvPhaseSheddingMask; // set this to 1 to set PSI0/1 to 1 in ULV mode
+
+  // SECTION: Telemetry Settings
+  uint16_t     GfxMaxCurrent;   // in Amps
+  uint8_t      GfxOffset;       // in Amps
+  uint8_t      Padding_TelemetryGfx;
+
+  uint16_t     SocMaxCurrent;   // in Amps
+  uint8_t      SocOffset;       // in Amps
+  uint8_t      Padding_TelemetrySoc;
+
+  uint16_t     Mem0MaxCurrent;   // in Amps
+  uint8_t      Mem0Offset;       // in Amps
+  uint8_t      Padding_TelemetryMem0;
+  
+  uint16_t     Mem1MaxCurrent;   // in Amps
+  uint8_t      Mem1Offset;       // in Amps
+  uint8_t      Padding_TelemetryMem1;
+
+  uint32_t     MvddRatio; // This is used for MVDD  Svi2 Div Ratio workaround. It has 16 fractional bits (Q16.16)
+  
+  // SECTION: GPIO Settings
+  uint8_t      AcDcGpio;        // GPIO pin configured for AC/DC switching
+  uint8_t      AcDcPolarity;    // GPIO polarity for AC/DC switching
+  uint8_t      VR0HotGpio;      // GPIO pin configured for VR0 HOT event
+  uint8_t      VR0HotPolarity;  // GPIO polarity for VR0 HOT event
+
+  uint8_t      VR1HotGpio;      // GPIO pin configured for VR1 HOT event 
+  uint8_t      VR1HotPolarity;  // GPIO polarity for VR1 HOT event 
+  uint8_t      GthrGpio;        // GPIO pin configured for GTHR Event
+  uint8_t      GthrPolarity;    // replace GPIO polarity for GTHR
+
+  // LED Display Settings
+  uint8_t      LedPin0;         // GPIO number for LedPin[0]
+  uint8_t      LedPin1;         // GPIO number for LedPin[1]
+  uint8_t      LedPin2;         // GPIO number for LedPin[2]
+  uint8_t      LedEnableMask;
+
+  uint8_t      LedPcie;        // GPIO number for PCIE results
+  uint8_t      LedError;       // GPIO number for Error Cases
+  uint8_t      LedSpare1[2];
+
+  // SECTION: Clock Spread Spectrum
+  
+  // GFXCLK PLL Spread Spectrum
+  uint8_t      PllGfxclkSpreadEnabled;   // on or off
+  uint8_t      PllGfxclkSpreadPercent;   // Q4.4
+  uint16_t     PllGfxclkSpreadFreq;      // kHz
+
+  // GFXCLK DFLL Spread Spectrum
+  uint8_t      DfllGfxclkSpreadEnabled;   // on or off
+  uint8_t      DfllGfxclkSpreadPercent;   // Q4.4
+  uint16_t     DfllGfxclkSpreadFreq;      // kHz
+  
+  // UCLK Spread Spectrum
+  uint8_t      UclkSpreadEnabled;   // on or off
+  uint8_t      UclkSpreadPercent;   // Q4.4
+  uint16_t     UclkSpreadFreq;      // kHz
+
+  // FCLK Spread Spectrum
+  uint8_t      FclkSpreadEnabled;   // on or off
+  uint8_t      FclkSpreadPercent;   // Q4.4
+  uint16_t     FclkSpreadFreq;      // kHz
+  
+  // Section: Memory Config
+  uint32_t     MemoryChannelEnabled; // For DRAM use only, Max 32 channels enabled bit mask. 
+  
+  uint8_t      DramBitWidth; // For DRAM use only.  See Dram Bit width type defines
+  uint8_t      PaddingMem1[3];
+
+  // Section: Total Board Power
+  uint16_t     TotalBoardPower;     //Only needed for TCP Estimated case, where TCP = TGP+Total Board Power
+  uint16_t     BoardPowerPadding; 
+  
+  // SECTION: XGMI Training
+  uint8_t      XgmiLinkSpeed   [4];
+  uint8_t      XgmiLinkWidth   [4];
+
+  uint16_t     XgmiFclkFreq    [4];
+  uint16_t     XgmiSocVoltage  [4];
+
+  // SECTION: Board Reserved
+
+  uint32_t     BoardReserved[16];
+
+};
+
 /* 
   ***************************************************************************
     Data Table asic_profiling_info  structure