Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Two minor conflicts:

1) net/ipv4/route.c, adding a new local variable while
   moving another local variable and removing it's
   initial assignment.

2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
   One pretty prints the port mode differently, whilst another
   changes the driver to try and obtain the port mode from
   the port node rather than the switch node.

Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 20 insertions, 24 deletions

diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index f797c971cd82..124524ecfe26 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1916,24 +1916,12 @@ static inline bool uart_console_enabled(struct uart_port *port)
 	return uart_console(port) && (port->cons->flags & CON_ENABLED);
 }
 
-static void __uart_port_spin_lock_init(struct uart_port *port)
+static void uart_port_spin_lock_init(struct uart_port *port)
 {
 	spin_lock_init(&port->lock);
 	lockdep_set_class(&port->lock, &port_lock_key);
 }
 
-/*
- * Ensure that the serial console lock is initialised early.
- * If this port is a console, then the spinlock is already initialised.
- */
-static inline void uart_port_spin_lock_init(struct uart_port *port)
-{
-	if (uart_console(port))
-		return;
-
-	__uart_port_spin_lock_init(port);
-}
-
 #if defined(CONFIG_SERIAL_CORE_CONSOLE) || defined(CONFIG_CONSOLE_POLL)
 /**
  *	uart_console_write - write a console message to a serial port
@@ -2086,7 +2074,15 @@ uart_set_options(struct uart_port *port, struct console *co,
 	struct ktermios termios;
 	static struct ktermios dummy;
 
-	uart_port_spin_lock_init(port);
+	/*
+	 * Ensure that the serial-console lock is initialised early.
+	 *
+	 * Note that the console-enabled check is needed because of kgdboc,
+	 * which can end up calling uart_set_options() for an already enabled
+	 * console via tty_find_polling_driver() and uart_poll_init().
+	 */
+	if (!uart_console_enabled(port) && !port->console_reinit)
+		uart_port_spin_lock_init(port);
 
 	memset(&termios, 0, sizeof(struct ktermios));
 
@@ -2379,13 +2375,6 @@ uart_configure_port(struct uart_driver *drv, struct uart_state *state,
 		uart_change_pm(state, UART_PM_STATE_ON);
 
 		/*
-		 * If this driver supports console, and it hasn't been
-		 * successfully registered yet, initialise spin lock for it.
-		 */
-		if (port->cons && !(port->cons->flags & CON_ENABLED))
-			__uart_port_spin_lock_init(port);
-
-		/*
 		 * Ensure that the modem control lines are de-activated.
 		 * keep the DTR setting that is set in uart_set_options()
 		 * We probably don't need a spinlock around this, but
@@ -2801,10 +2790,12 @@ static ssize_t console_store(struct device *dev,
 		if (oldconsole && !newconsole) {
 			ret = unregister_console(uport->cons);
 		} else if (!oldconsole && newconsole) {
-			if (uart_console(uport))
+			if (uart_console(uport)) {
+				uport->console_reinit = 1;
 				register_console(uport->cons);
-			else
+			} else {
 				ret = -ENOENT;
+			}
 		}
 	} else {
 		ret = -ENXIO;
@@ -2900,7 +2891,12 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *uport)
 		goto out;
 	}
 
-	uart_port_spin_lock_init(uport);
+	/*
+	 * If this port is in use as a console then the spinlock is already
+	 * initialised.
+	 */
+	if (!uart_console_enabled(uport))
+		uart_port_spin_lock_init(uport);
 
 	if (uport->cons && uport->dev)
 		of_console_check(uport->dev->of_node, uport->cons->name, uport->line);