Merge tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Decrease polling rate for erase/trim/discard
   - Allow non-sleeping GPIOs for card detect
   - Improve mmc block removal path
   - Enable support for mmc_sw_reset() for SDIO cards
   - Add mmc_sw_reset() to allow users to do a soft reset of the card
   - Allow power delay to be tunable via DT
   - Allow card detect debounce delay to be tunable via DT
   - Enable new quirk to limit clock rate for Marvell 8887 chip
   - Don't show eMMC RPMB and BOOT areas in /proc/partitions
   - Add capability to avoid 3.3V signaling for fragile HWs

  MMC host:
   - Improve/fixup support for handle highmem pages
   - Remove depends on HAS_DMA in case of platform dependency
   - mvsdio: Enable support for erase/trim/discard
   - rtsx_usb: Enable support for erase/trim/discard
   - renesas_sdhi: Fix WP logic regressions
   - renesas_sdhi: Add r8a77965 support
   - renesas_sdhi: Add R8A77980 to whitelist
   - meson: Add optional support for device reset
   - meson: Add support for the Meson-AXG platform
   - dw_mmc: Add new driver for BlueField DW variant
   - mediatek: Add support for 64G DRAM DMA
   - sunxi: Deploy runtime PM support
   - jz4740: Add support for JZ4780
   - jz4740: Enable support for DT based platforms
   - sdhci: Various improvement to timeout handling
   - sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
   - sdhci-omap: Add support for controller in k2g SoC
   - sdhci-omap: Add workarounds for a couple of Erratas
   - sdhci-omap: Enable support for generic sdhci DT properties
   - sdhci-cadence: Re-send tune request to deal with errata
   - sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
   - sdhci-pci: Avoid 3.3V signaling on some NI 904x
   - sdhci-esdhc-imx: Use watermark levels for PIO access
   - sdhci-msm: Improve card detection handling
   - sdhci-msm: Add support voltage pad switching"

* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
  mmc: renesas_sdhi: really fix WP logic regressions
  mmc: mvsdio: Enable MMC_CAP_ERASE
  mmc: mvsdio: Respect card busy time out from mmc core
  mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
  mmc: sunxi: Use ifdef rather than __maybe_unused
  mmc: mxmmc: Use ifdef rather than __maybe_unused
  mmc: mxmmc: include linux/highmem.h
  mmc: sunxi: mark PM functions as __maybe_unused
  mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
  mmc: au1xmmc: handle highmem pages
  mmc: Allow non-sleeping GPIO cd
  mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
  mmc: sd: Define name for default speed dtr
  mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
  mmc: sdhci-xenon: use match_string() helper
  mmc: wbsd: handle highmem pages
  mmc: ushc: handle highmem pages
  mmc: mxcmmc: handle highmem pages
  mmc: atmel-mci: use sg_copy_{from,to}_buffer
  mmc: android-goldfish: use sg_copy_{from,to}_buffer
  ...

5 files changed, 59 insertions, 0 deletions

diff --git a/include/dt-bindings/dma/jz4780-dma.h b/include/dt-bindings/dma/jz4780-dma.h
new file mode 100644
index 000000000000..df017fdfb44e
--- /dev/null
+++ b/include/dt-bindings/dma/jz4780-dma.h
@@ -0,0 +1,49 @@
+#ifndef __DT_BINDINGS_DMA_JZ4780_DMA_H__
+#define __DT_BINDINGS_DMA_JZ4780_DMA_H__
+
+/*
+ * Request type numbers for the JZ4780 DMA controller (written to the DRTn
+ * register for the channel).
+ */
+#define JZ4780_DMA_I2S1_TX	0x4
+#define JZ4780_DMA_I2S1_RX	0x5
+#define JZ4780_DMA_I2S0_TX	0x6
+#define JZ4780_DMA_I2S0_RX	0x7
+#define JZ4780_DMA_AUTO		0x8
+#define JZ4780_DMA_SADC_RX	0x9
+#define JZ4780_DMA_UART4_TX	0xc
+#define JZ4780_DMA_UART4_RX	0xd
+#define JZ4780_DMA_UART3_TX	0xe
+#define JZ4780_DMA_UART3_RX	0xf
+#define JZ4780_DMA_UART2_TX	0x10
+#define JZ4780_DMA_UART2_RX	0x11
+#define JZ4780_DMA_UART1_TX	0x12
+#define JZ4780_DMA_UART1_RX	0x13
+#define JZ4780_DMA_UART0_TX	0x14
+#define JZ4780_DMA_UART0_RX	0x15
+#define JZ4780_DMA_SSI0_TX	0x16
+#define JZ4780_DMA_SSI0_RX	0x17
+#define JZ4780_DMA_SSI1_TX	0x18
+#define JZ4780_DMA_SSI1_RX	0x19
+#define JZ4780_DMA_MSC0_TX	0x1a
+#define JZ4780_DMA_MSC0_RX	0x1b
+#define JZ4780_DMA_MSC1_TX	0x1c
+#define JZ4780_DMA_MSC1_RX	0x1d
+#define JZ4780_DMA_MSC2_TX	0x1e
+#define JZ4780_DMA_MSC2_RX	0x1f
+#define JZ4780_DMA_PCM0_TX	0x20
+#define JZ4780_DMA_PCM0_RX	0x21
+#define JZ4780_DMA_SMB0_TX	0x24
+#define JZ4780_DMA_SMB0_RX	0x25
+#define JZ4780_DMA_SMB1_TX	0x26
+#define JZ4780_DMA_SMB1_RX	0x27
+#define JZ4780_DMA_SMB2_TX	0x28
+#define JZ4780_DMA_SMB2_RX	0x29
+#define JZ4780_DMA_SMB3_TX	0x2a
+#define JZ4780_DMA_SMB3_RX	0x2b
+#define JZ4780_DMA_SMB4_TX	0x2c
+#define JZ4780_DMA_SMB4_RX	0x2d
+#define JZ4780_DMA_DES_TX	0x2e
+#define JZ4780_DMA_DES_RX	0x2f
+
+#endif /* __DT_BINDINGS_DMA_JZ4780_DMA_H__ */
diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
index 279b39008a33..de7377815b6b 100644
--- a/include/linux/mmc/card.h
+++ b/include/linux/mmc/card.h
@@ -156,6 +156,7 @@ struct sd_switch_caps {
 #define UHS_DDR50_MAX_DTR	50000000
 #define UHS_SDR25_MAX_DTR	UHS_DDR50_MAX_DTR
 #define UHS_SDR12_MAX_DTR	25000000
+#define DEFAULT_SPEED_MAX_DTR	UHS_SDR12_MAX_DTR
 	unsigned int		sd3_bus_mode;
 #define UHS_SDR12_BUS_SPEED	0
 #define HIGH_SPEED_BUS_SPEED	1
@@ -252,6 +253,7 @@ struct mmc_card {
 #define MMC_TYPE_SD_COMBO	3		/* SD combo (IO+mem) card */
 	unsigned int		state;		/* (our) card state */
 	unsigned int		quirks; 	/* card quirks */
+	unsigned int		quirk_max_rate;	/* max rate set by quirks */
 #define MMC_QUIRK_LENIENT_FN0	(1<<0)		/* allow SDIO FN0 writes outside of the VS CCCR range */
 #define MMC_QUIRK_BLKSZ_FOR_BYTE_MODE (1<<1)	/* use func->cur_blksize */
 						/* for byte mode */
diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
index 927519385482..134a6483347a 100644
--- a/include/linux/mmc/core.h
+++ b/include/linux/mmc/core.h
@@ -177,6 +177,7 @@ int mmc_wait_for_cmd(struct mmc_host *host, struct mmc_command *cmd,
 		int retries);
 
 int mmc_hw_reset(struct mmc_host *host);
+int mmc_sw_reset(struct mmc_host *host);
 void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card);
 
 #endif /* LINUX_MMC_CORE_H */
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index 85146235231e..64300a48dcce 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -22,6 +22,7 @@
 struct mmc_ios {
 	unsigned int	clock;			/* clock rate */
 	unsigned short	vdd;
+	unsigned int	power_delay_ms;		/* waiting for stable power */
 
 /* vdd stores the bit number of the selected voltage range from below. */
 
@@ -320,6 +321,9 @@ struct mmc_host {
 #define MMC_CAP_UHS_SDR50	(1 << 18)	/* Host supports UHS SDR50 mode */
 #define MMC_CAP_UHS_SDR104	(1 << 19)	/* Host supports UHS SDR104 mode */
 #define MMC_CAP_UHS_DDR50	(1 << 20)	/* Host supports UHS DDR50 mode */
+#define MMC_CAP_UHS		(MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 | \
+				 MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | \
+				 MMC_CAP_UHS_DDR50)
 /* (1 << 21) is free for reuse */
 #define MMC_CAP_DRIVER_TYPE_A	(1 << 23)	/* Host supports Driver Type A */
 #define MMC_CAP_DRIVER_TYPE_C	(1 << 24)	/* Host supports Driver Type C */
@@ -345,6 +349,7 @@ struct mmc_host {
 #define MMC_CAP2_HS400_1_2V	(1 << 16)	/* Can support HS400 1.2V */
 #define MMC_CAP2_HS400		(MMC_CAP2_HS400_1_8V | \
 				 MMC_CAP2_HS400_1_2V)
+#define MMC_CAP2_HSX00_1_8V	(MMC_CAP2_HS200_1_8V_SDR | MMC_CAP2_HS400_1_8V)
 #define MMC_CAP2_HSX00_1_2V	(MMC_CAP2_HS200_1_2V_SDR | MMC_CAP2_HS400_1_2V)
 #define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17)
 #define MMC_CAP2_NO_WRITE_PROTECT (1 << 18)	/* No physical write protect pin, assume that card is always read-write */
@@ -354,6 +359,7 @@ struct mmc_host {
 #define MMC_CAP2_NO_MMC		(1 << 22)	/* Do not send (e)MMC commands during initialization */
 #define MMC_CAP2_CQE		(1 << 23)	/* Has eMMC command queue engine */
 #define MMC_CAP2_CQE_DCMD	(1 << 24)	/* CQE can issue a direct command */
+#define MMC_CAP2_AVOID_3_3V	(1 << 25)	/* Host must negotiate down from 3.3V */
 
 	int			fixed_drv_type;	/* fixed driver type for non-removable media */
 
diff --git a/include/linux/mmc/sdio_ids.h b/include/linux/mmc/sdio_ids.h
index cdd66a5fbd5e..2836a96e014a 100644
--- a/include/linux/mmc/sdio_ids.h
+++ b/include/linux/mmc/sdio_ids.h
@@ -55,6 +55,7 @@
 #define SDIO_DEVICE_ID_MARVELL_8688WLAN		0x9104
 #define SDIO_DEVICE_ID_MARVELL_8688BT		0x9105
 #define SDIO_DEVICE_ID_MARVELL_8797_F0		0x9128
+#define SDIO_DEVICE_ID_MARVELL_8887WLAN	0x9134
 
 #define SDIO_VENDOR_ID_SIANO			0x039a
 #define SDIO_DEVICE_ID_SIANO_NOVA_B0		0x0201