Merge tag 'spi-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "One small core feature this time around but mostly driver improvements
  and additions for SPI:

   - Add support for controlling the idle state of MOSI, some systems
     can support this and depending on the system integration may need
     it to avoid glitching in some situations

   - Support for polling mode in the S3C64xx driver and DMA on the
     Qualcomm QSPI driver

   - Support for several Allwinner SoCs, AMD Pensando Elba, Intel Mount
     Evans, Renesas RZ/V2M, and ST STM32H7"

* tag 'spi-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (66 commits)
  spi: dt-bindings: atmel,at91rm9200-spi: fix broken sam9x7 compatible
  spi: dt-bindings: atmel,at91rm9200-spi: add sam9x7 compatible
  spi: Add support for Renesas CSI
  spi: dt-bindings: Add bindings for RZ/V2M CSI
  spi: sun6i: Use the new helper to derive the xfer timeout value
  spi: atmel: Prevent false timeouts on long transfers
  spi: dt-bindings: stm32: do not disable spi-slave property for stm32f4-f7
  spi: Create a helper to derive adaptive timeouts
  spi: spi-geni-qcom: correctly handle -EPROBE_DEFER from dma_request_chan()
  spi: stm32: disable spi-slave property for stm32f4-f7
  spi: stm32: introduction of stm32h7 SPI device mode support
  spi: stm32: use dmaengine_terminate_{a}sync instead of _all
  spi: stm32: renaming of spi_master into spi_controller
  spi: dw: Remove misleading comment for Mount Evans SoC
  spi: dt-bindings: snps,dw-apb-ssi: Add compatible for Intel Mount Evans SoC
  spi: dw: Add compatible for Intel Mount Evans SoC
  spi: s3c64xx: Use dev_err_probe()
  spi: s3c64xx: Use the managed spi master allocation function
  spi: spl022: Probe defer is no error
  spi: spi-imx: fix mixing of native and gpio chipselects for imx51/imx53/imx6 variants
  ...

1 files changed, 64 insertions, 43 deletions

diff --git a/tools/spi/spidev_test.c b/tools/spi/spidev_test.c
index b0ca44c70e83..9179942d7f15 100644
--- a/tools/spi/spidev_test.c
+++ b/tools/spi/spidev_test.c
@@ -172,28 +172,37 @@ static void transfer(int fd, uint8_t const *tx, uint8_t const *rx, size_t len)
 
 static void print_usage(const char *prog)
 {
-	printf("Usage: %s [-DsbdlHOLC3vpNR24SI]\n", prog);
-	puts("  -D --device   device to use (default /dev/spidev1.1)\n"
-	     "  -s --speed    max speed (Hz)\n"
-	     "  -d --delay    delay (usec)\n"
-	     "  -b --bpw      bits per word\n"
-	     "  -i --input    input data from a file (e.g. \"test.bin\")\n"
-	     "  -o --output   output data to a file (e.g. \"results.bin\")\n"
-	     "  -l --loop     loopback\n"
-	     "  -H --cpha     clock phase\n"
-	     "  -O --cpol     clock polarity\n"
-	     "  -L --lsb      least significant bit first\n"
-	     "  -C --cs-high  chip select active high\n"
-	     "  -3 --3wire    SI/SO signals shared\n"
-	     "  -v --verbose  Verbose (show tx buffer)\n"
-	     "  -p            Send data (e.g. \"1234\\xde\\xad\")\n"
-	     "  -N --no-cs    no chip select\n"
-	     "  -R --ready    slave pulls low to pause\n"
-	     "  -2 --dual     dual transfer\n"
-	     "  -4 --quad     quad transfer\n"
-	     "  -8 --octal    octal transfer\n"
-	     "  -S --size     transfer size\n"
-	     "  -I --iter     iterations\n");
+	printf("Usage: %s [-2348CDFHILMNORSZbdilopsv]\n", prog);
+	puts("general device settings:\n"
+		 "  -D --device         device to use (default /dev/spidev1.1)\n"
+		 "  -s --speed          max speed (Hz)\n"
+		 "  -d --delay          delay (usec)\n"
+		 "  -l --loop           loopback\n"
+		 "spi mode:\n"
+		 "  -H --cpha           clock phase\n"
+		 "  -O --cpol           clock polarity\n"
+		 "  -F --rx-cpha-flip   flip CPHA on Rx only xfer\n"
+		 "number of wires for transmission:\n"
+		 "  -2 --dual           dual transfer\n"
+		 "  -4 --quad           quad transfer\n"
+		 "  -8 --octal          octal transfer\n"
+		 "  -3 --3wire          SI/SO signals shared\n"
+		 "  -Z --3wire-hiz      high impedance turnaround\n"
+		 "data:\n"
+		 "  -i --input          input data from a file (e.g. \"test.bin\")\n"
+		 "  -o --output         output data to a file (e.g. \"results.bin\")\n"
+		 "  -p                  Send data (e.g. \"1234\\xde\\xad\")\n"
+		 "  -S --size           transfer size\n"
+		 "  -I --iter           iterations\n"
+		 "additional parameters:\n"
+		 "  -b --bpw            bits per word\n"
+		 "  -L --lsb            least significant bit first\n"
+		 "  -C --cs-high        chip select active high\n"
+		 "  -N --no-cs          no chip select\n"
+		 "  -R --ready          slave pulls low to pause\n"
+		 "  -M --mosi-idle-low  leave mosi line low when idle\n"
+		 "misc:\n"
+		 "  -v --verbose        Verbose (show tx buffer)\n");
 	exit(1);
 }
 
@@ -201,31 +210,34 @@ static void parse_opts(int argc, char *argv[])
 {
 	while (1) {
 		static const struct option lopts[] = {
-			{ "device",  1, 0, 'D' },
-			{ "speed",   1, 0, 's' },
-			{ "delay",   1, 0, 'd' },
-			{ "bpw",     1, 0, 'b' },
-			{ "input",   1, 0, 'i' },
-			{ "output",  1, 0, 'o' },
-			{ "loop",    0, 0, 'l' },
-			{ "cpha",    0, 0, 'H' },
-			{ "cpol",    0, 0, 'O' },
-			{ "lsb",     0, 0, 'L' },
-			{ "cs-high", 0, 0, 'C' },
-			{ "3wire",   0, 0, '3' },
-			{ "no-cs",   0, 0, 'N' },
-			{ "ready",   0, 0, 'R' },
-			{ "dual",    0, 0, '2' },
-			{ "verbose", 0, 0, 'v' },
-			{ "quad",    0, 0, '4' },
-			{ "octal",   0, 0, '8' },
-			{ "size",    1, 0, 'S' },
-			{ "iter",    1, 0, 'I' },
+			{ "device",        1, 0, 'D' },
+			{ "speed",         1, 0, 's' },
+			{ "delay",         1, 0, 'd' },
+			{ "loop",          0, 0, 'l' },
+			{ "cpha",          0, 0, 'H' },
+			{ "cpol",          0, 0, 'O' },
+			{ "rx-cpha-flip",  0, 0, 'F' },
+			{ "dual",          0, 0, '2' },
+			{ "quad",          0, 0, '4' },
+			{ "octal",         0, 0, '8' },
+			{ "3wire",         0, 0, '3' },
+			{ "3wire-hiz",     0, 0, 'Z' },
+			{ "input",         1, 0, 'i' },
+			{ "output",        1, 0, 'o' },
+			{ "size",          1, 0, 'S' },
+			{ "iter",          1, 0, 'I' },
+			{ "bpw",           1, 0, 'b' },
+			{ "lsb",           0, 0, 'L' },
+			{ "cs-high",       0, 0, 'C' },
+			{ "no-cs",         0, 0, 'N' },
+			{ "ready",         0, 0, 'R' },
+			{ "mosi-idle-low", 0, 0, 'M' },
+			{ "verbose",       0, 0, 'v' },
 			{ NULL, 0, 0, 0 },
 		};
 		int c;
 
-		c = getopt_long(argc, argv, "D:s:d:b:i:o:lHOLC3NR248p:vS:I:",
+		c = getopt_long(argc, argv, "D:s:d:b:i:o:lHOLC3ZFMNR248p:vS:I:",
 				lopts, NULL);
 
 		if (c == -1)
@@ -268,6 +280,15 @@ static void parse_opts(int argc, char *argv[])
 		case '3':
 			mode |= SPI_3WIRE;
 			break;
+		case 'Z':
+			mode |= SPI_3WIRE_HIZ;
+			break;
+		case 'F':
+			mode |= SPI_RX_CPHA_FLIP;
+			break;
+		case 'M':
+			mode |= SPI_MOSI_IDLE_LOW;
+			break;
 		case 'N':
 			mode |= SPI_NO_CS;
 			break;