summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--drivers/soc/qcom/Kconfig9
-rw-r--r--drivers/soc/qcom/Makefile1
-rw-r--r--drivers/soc/qcom/qcom-geni-se.c748
-rw-r--r--include/linux/qcom-geni-se.h425
4 files changed, 1183 insertions, 0 deletions
diff --git a/drivers/soc/qcom/Kconfig b/drivers/soc/qcom/Kconfig
index 5c4535b545cc..d0372de29834 100644
--- a/drivers/soc/qcom/Kconfig
+++ b/drivers/soc/qcom/Kconfig
@@ -3,6 +3,15 @@
#
menu "Qualcomm SoC drivers"
+config QCOM_GENI_SE
+ tristate "QCOM GENI Serial Engine Driver"
+ depends on ARCH_QCOM || COMPILE_TEST
+ help
+ This driver is used to manage Generic Interface (GENI) firmware based
+ Qualcomm Technologies, Inc. Universal Peripheral (QUP) Wrapper. This
+ driver is also used to manage the common aspects of multiple Serial
+ Engines present in the QUP.
+
config QCOM_GLINK_SSR
tristate "Qualcomm Glink SSR driver"
depends on RPMSG
diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile
index dcebf2814e6d..959aa748f5ac 100644
--- a/drivers/soc/qcom/Makefile
+++ b/drivers/soc/qcom/Makefile
@@ -1,4 +1,5 @@
# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_QCOM_GENI_SE) += qcom-geni-se.o
obj-$(CONFIG_QCOM_GLINK_SSR) += glink_ssr.o
obj-$(CONFIG_QCOM_GSBI) += qcom_gsbi.o
obj-$(CONFIG_QCOM_MDT_LOADER) += mdt_loader.o
diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c
new file mode 100644
index 000000000000..feed3db21c10
--- /dev/null
+++ b/drivers/soc/qcom/qcom-geni-se.c
@@ -0,0 +1,748 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017-2018, The Linux Foundation. All rights reserved.
+
+#include <linux/clk.h>
+#include <linux/slab.h>
+#include <linux/dma-mapping.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/qcom-geni-se.h>
+
+/**
+ * DOC: Overview
+ *
+ * Generic Interface (GENI) Serial Engine (SE) Wrapper driver is introduced
+ * to manage GENI firmware based Qualcomm Universal Peripheral (QUP) Wrapper
+ * controller. QUP Wrapper is designed to support various serial bus protocols
+ * like UART, SPI, I2C, I3C, etc.
+ */
+
+/**
+ * DOC: Hardware description
+ *
+ * GENI based QUP is a highly-flexible and programmable module for supporting
+ * a wide range of serial interfaces like UART, SPI, I2C, I3C, etc. A single
+ * QUP module can provide upto 8 serial interfaces, using its internal
+ * serial engines. The actual configuration is determined by the target
+ * platform configuration. The protocol supported by each interface is
+ * determined by the firmware loaded to the serial engine. Each SE consists
+ * of a DMA Engine and GENI sub modules which enable serial engines to
+ * support FIFO and DMA modes of operation.
+ *
+ *
+ * +-----------------------------------------+
+ * |QUP Wrapper |
+ * | +----------------------------+ |
+ * --QUP & SE Clocks--> | Serial Engine N | +-IO------>
+ * | | ... | | Interface
+ * <---Clock Perf.----+ +----+-----------------------+ | |
+ * State Interface | | Serial Engine 1 | | |
+ * | | | | |
+ * | | | | |
+ * <--------AHB-------> | | | |
+ * | | +----+ |
+ * | | | |
+ * | | | |
+ * <------SE IRQ------+ +----------------------------+ |
+ * | |
+ * +-----------------------------------------+
+ *
+ * Figure 1: GENI based QUP Wrapper
+ *
+ * The GENI submodules include primary and secondary sequencers which are
+ * used to drive TX & RX operations. On serial interfaces that operate using
+ * master-slave model, primary sequencer drives both TX & RX operations. On
+ * serial interfaces that operate using peer-to-peer model, primary sequencer
+ * drives TX operation and secondary sequencer drives RX operation.
+ */
+
+/**
+ * DOC: Software description
+ *
+ * GENI SE Wrapper driver is structured into 2 parts:
+ *
+ * geni_wrapper represents QUP Wrapper controller. This part of the driver
+ * manages QUP Wrapper information such as hardware version, clock
+ * performance table that is common to all the internal serial engines.
+ *
+ * geni_se represents serial engine. This part of the driver manages serial
+ * engine information such as clocks, containing QUP Wrapper, etc. This part
+ * of driver also supports operations (eg. initialize the concerned serial
+ * engine, select between FIFO and DMA mode of operation etc.) that are
+ * common to all the serial engines and are independent of serial interfaces.
+ */
+
+#define MAX_CLK_PERF_LEVEL 32
+#define NUM_AHB_CLKS 2
+
+/**
+ * @struct geni_wrapper - Data structure to represent the QUP Wrapper Core
+ * @dev: Device pointer of the QUP wrapper core
+ * @base: Base address of this instance of QUP wrapper core
+ * @ahb_clks: Handle to the primary & secondary AHB clocks
+ */
+struct geni_wrapper {
+ struct device *dev;
+ void __iomem *base;
+ struct clk_bulk_data ahb_clks[NUM_AHB_CLKS];
+};
+
+#define QUP_HW_VER_REG 0x4
+
+/* Common SE registers */
+#define GENI_INIT_CFG_REVISION 0x0
+#define GENI_S_INIT_CFG_REVISION 0x4
+#define GENI_OUTPUT_CTRL 0x24
+#define GENI_CGC_CTRL 0x28
+#define GENI_CLK_CTRL_RO 0x60
+#define GENI_IF_DISABLE_RO 0x64
+#define GENI_FW_S_REVISION_RO 0x6c
+#define SE_GENI_BYTE_GRAN 0x254
+#define SE_GENI_TX_PACKING_CFG0 0x260
+#define SE_GENI_TX_PACKING_CFG1 0x264
+#define SE_GENI_RX_PACKING_CFG0 0x284
+#define SE_GENI_RX_PACKING_CFG1 0x288
+#define SE_GENI_M_GP_LENGTH 0x910
+#define SE_GENI_S_GP_LENGTH 0x914
+#define SE_DMA_TX_PTR_L 0xc30
+#define SE_DMA_TX_PTR_H 0xc34
+#define SE_DMA_TX_ATTR 0xc38
+#define SE_DMA_TX_LEN 0xc3c
+#define SE_DMA_TX_IRQ_EN 0xc48
+#define SE_DMA_TX_IRQ_EN_SET 0xc4c
+#define SE_DMA_TX_IRQ_EN_CLR 0xc50
+#define SE_DMA_TX_LEN_IN 0xc54
+#define SE_DMA_TX_MAX_BURST 0xc5c
+#define SE_DMA_RX_PTR_L 0xd30
+#define SE_DMA_RX_PTR_H 0xd34
+#define SE_DMA_RX_ATTR 0xd38
+#define SE_DMA_RX_LEN 0xd3c
+#define SE_DMA_RX_IRQ_EN 0xd48
+#define SE_DMA_RX_IRQ_EN_SET 0xd4c
+#define SE_DMA_RX_IRQ_EN_CLR 0xd50
+#define SE_DMA_RX_LEN_IN 0xd54
+#define SE_DMA_RX_MAX_BURST 0xd5c
+#define SE_DMA_RX_FLUSH 0xd60
+#define SE_GSI_EVENT_EN 0xe18
+#define SE_IRQ_EN 0xe1c
+#define SE_DMA_GENERAL_CFG 0xe30
+
+/* GENI_OUTPUT_CTRL fields */
+#define DEFAULT_IO_OUTPUT_CTRL_MSK GENMASK(6, 0)
+
+/* GENI_CGC_CTRL fields */
+#define CFG_AHB_CLK_CGC_ON BIT(0)
+#define CFG_AHB_WR_ACLK_CGC_ON BIT(1)
+#define DATA_AHB_CLK_CGC_ON BIT(2)
+#define SCLK_CGC_ON BIT(3)
+#define TX_CLK_CGC_ON BIT(4)
+#define RX_CLK_CGC_ON BIT(5)
+#define EXT_CLK_CGC_ON BIT(6)
+#define PROG_RAM_HCLK_OFF BIT(8)
+#define PROG_RAM_SCLK_OFF BIT(9)
+#define DEFAULT_CGC_EN GENMASK(6, 0)
+
+/* SE_GSI_EVENT_EN fields */
+#define DMA_RX_EVENT_EN BIT(0)
+#define DMA_TX_EVENT_EN BIT(1)
+#define GENI_M_EVENT_EN BIT(2)
+#define GENI_S_EVENT_EN BIT(3)
+
+/* SE_IRQ_EN fields */
+#define DMA_RX_IRQ_EN BIT(0)
+#define DMA_TX_IRQ_EN BIT(1)
+#define GENI_M_IRQ_EN BIT(2)
+#define GENI_S_IRQ_EN BIT(3)
+
+/* SE_DMA_GENERAL_CFG */
+#define DMA_RX_CLK_CGC_ON BIT(0)
+#define DMA_TX_CLK_CGC_ON BIT(1)
+#define DMA_AHB_SLV_CFG_ON BIT(2)
+#define AHB_SEC_SLV_CLK_CGC_ON BIT(3)
+#define DUMMY_RX_NON_BUFFERABLE BIT(4)
+#define RX_DMA_ZERO_PADDING_EN BIT(5)
+#define RX_DMA_IRQ_DELAY_MSK GENMASK(8, 6)
+#define RX_DMA_IRQ_DELAY_SHFT 6
+
+/**
+ * geni_se_get_qup_hw_version() - Read the QUP wrapper Hardware version
+ * @se: Pointer to the corresponding serial engine.
+ *
+ * Return: Hardware Version of the wrapper.
+ */
+u32 geni_se_get_qup_hw_version(struct geni_se *se)
+{
+ struct geni_wrapper *wrapper = se->wrapper;
+
+ return readl_relaxed(wrapper->base + QUP_HW_VER_REG);
+}
+EXPORT_SYMBOL(geni_se_get_qup_hw_version);
+
+static void geni_se_io_set_mode(void __iomem *base)
+{
+ u32 val;
+
+ val = readl_relaxed(base + SE_IRQ_EN);
+ val |= GENI_M_IRQ_EN | GENI_S_IRQ_EN;
+ val |= DMA_TX_IRQ_EN | DMA_RX_IRQ_EN;
+ writel_relaxed(val, base + SE_IRQ_EN);
+
+ val = readl_relaxed(base + SE_GENI_DMA_MODE_EN);
+ val &= ~GENI_DMA_MODE_EN;
+ writel_relaxed(val, base + SE_GENI_DMA_MODE_EN);
+
+ writel_relaxed(0, base + SE_GSI_EVENT_EN);
+}
+
+static void geni_se_io_init(void __iomem *base)
+{
+ u32 val;
+
+ val = readl_relaxed(base + GENI_CGC_CTRL);
+ val |= DEFAULT_CGC_EN;
+ writel_relaxed(val, base + GENI_CGC_CTRL);
+
+ val = readl_relaxed(base + SE_DMA_GENERAL_CFG);
+ val |= AHB_SEC_SLV_CLK_CGC_ON | DMA_AHB_SLV_CFG_ON;
+ val |= DMA_TX_CLK_CGC_ON | DMA_RX_CLK_CGC_ON;
+ writel_relaxed(val, base + SE_DMA_GENERAL_CFG);
+
+ writel_relaxed(DEFAULT_IO_OUTPUT_CTRL_MSK, base + GENI_OUTPUT_CTRL);
+ writel_relaxed(FORCE_DEFAULT, base + GENI_FORCE_DEFAULT_REG);
+}
+
+/**
+ * geni_se_init() - Initialize the GENI serial engine
+ * @se: Pointer to the concerned serial engine.
+ * @rx_wm: Receive watermark, in units of FIFO words.
+ * @rx_rfr_wm: Ready-for-receive watermark, in units of FIFO words.
+ *
+ * This function is used to initialize the GENI serial engine, configure
+ * receive watermark and ready-for-receive watermarks.
+ */
+void geni_se_init(struct geni_se *se, u32 rx_wm, u32 rx_rfr)
+{
+ u32 val;
+
+ geni_se_io_init(se->base);
+ geni_se_io_set_mode(se->base);
+
+ writel_relaxed(rx_wm, se->base + SE_GENI_RX_WATERMARK_REG);
+ writel_relaxed(rx_rfr, se->base + SE_GENI_RX_RFR_WATERMARK_REG);
+
+ val = readl_relaxed(se->base + SE_GENI_M_IRQ_EN);
+ val |= M_COMMON_GENI_M_IRQ_EN;
+ writel_relaxed(val, se->base + SE_GENI_M_IRQ_EN);
+
+ val = readl_relaxed(se->base + SE_GENI_S_IRQ_EN);
+ val |= S_COMMON_GENI_S_IRQ_EN;
+ writel_relaxed(val, se->base + SE_GENI_S_IRQ_EN);
+}
+EXPORT_SYMBOL(geni_se_init);
+
+static void geni_se_select_fifo_mode(struct geni_se *se)
+{
+ u32 proto = geni_se_read_proto(se);
+ u32 val;
+
+ writel_relaxed(0, se->base + SE_GSI_EVENT_EN);
+ writel_relaxed(0xffffffff, se->base + SE_GENI_M_IRQ_CLEAR);
+ writel_relaxed(0xffffffff, se->base + SE_GENI_S_IRQ_CLEAR);
+ writel_relaxed(0xffffffff, se->base + SE_DMA_TX_IRQ_CLR);
+ writel_relaxed(0xffffffff, se->base + SE_DMA_RX_IRQ_CLR);
+ writel_relaxed(0xffffffff, se->base + SE_IRQ_EN);
+
+ val = readl_relaxed(se->base + SE_GENI_M_IRQ_EN);
+ if (proto != GENI_SE_UART) {
+ val |= M_CMD_DONE_EN | M_TX_FIFO_WATERMARK_EN;
+ val |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN;
+ }
+ writel_relaxed(val, se->base + SE_GENI_M_IRQ_EN);
+
+ val = readl_relaxed(se->base + SE_GENI_S_IRQ_EN);
+ if (proto != GENI_SE_UART)
+ val |= S_CMD_DONE_EN;
+ writel_relaxed(val, se->base + SE_GENI_S_IRQ_EN);
+
+ val = readl_relaxed(se->base + SE_GENI_DMA_MODE_EN);
+ val &= ~GENI_DMA_MODE_EN;
+ writel_relaxed(val, se->base + SE_GENI_DMA_MODE_EN);
+}
+
+static void geni_se_select_dma_mode(struct geni_se *se)
+{
+ u32 val;
+
+ writel_relaxed(0, se->base + SE_GSI_EVENT_EN);
+ writel_relaxed(0xffffffff, se->base + SE_GENI_M_IRQ_CLEAR);
+ writel_relaxed(0xffffffff, se->base + SE_GENI_S_IRQ_CLEAR);
+ writel_relaxed(0xffffffff, se->base + SE_DMA_TX_IRQ_CLR);
+ writel_relaxed(0xffffffff, se->base + SE_DMA_RX_IRQ_CLR);
+ writel_relaxed(0xffffffff, se->base + SE_IRQ_EN);
+
+ val = readl_relaxed(se->base + SE_GENI_DMA_MODE_EN);
+ val |= GENI_DMA_MODE_EN;
+ writel_relaxed(val, se->base + SE_GENI_DMA_MODE_EN);
+}
+
+/**
+ * geni_se_select_mode() - Select the serial engine transfer mode
+ * @se: Pointer to the concerned serial engine.
+ * @mode: Transfer mode to be selected.
+ */
+void geni_se_select_mode(struct geni_se *se, enum geni_se_xfer_mode mode)
+{
+ WARN_ON(mode != GENI_SE_FIFO && mode != GENI_SE_DMA);
+
+ switch (mode) {
+ case GENI_SE_FIFO:
+ geni_se_select_fifo_mode(se);
+ break;
+ case GENI_SE_DMA:
+ geni_se_select_dma_mode(se);
+ break;
+ case GENI_SE_INVALID:
+ default:
+ break;
+ }
+}
+EXPORT_SYMBOL(geni_se_select_mode);
+
+/**
+ * DOC: Overview
+ *
+ * GENI FIFO packing is highly configurable. TX/RX packing/unpacking consist
+ * of up to 4 operations, each operation represented by 4 configuration vectors
+ * of 10 bits programmed in GENI_TX_PACKING_CFG0 and GENI_TX_PACKING_CFG1 for
+ * TX FIFO and in GENI_RX_PACKING_CFG0 and GENI_RX_PACKING_CFG1 for RX FIFO.
+ * Refer to below examples for detailed bit-field description.
+ *
+ * Example 1: word_size = 7, packing_mode = 4 x 8, msb_to_lsb = 1
+ *
+ * +-----------+-------+-------+-------+-------+
+ * | | vec_0 | vec_1 | vec_2 | vec_3 |
+ * +-----------+-------+-------+-------+-------+
+ * | start | 0x6 | 0xe | 0x16 | 0x1e |
+ * | direction | 1 | 1 | 1 | 1 |
+ * | length | 6 | 6 | 6 | 6 |
+ * | stop | 0 | 0 | 0 | 1 |
+ * +-----------+-------+-------+-------+-------+
+ *
+ * Example 2: word_size = 15, packing_mode = 2 x 16, msb_to_lsb = 0
+ *
+ * +-----------+-------+-------+-------+-------+
+ * | | vec_0 | vec_1 | vec_2 | vec_3 |
+ * +-----------+-------+-------+-------+-------+
+ * | start | 0x0 | 0x8 | 0x10 | 0x18 |
+ * | direction | 0 | 0 | 0 | 0 |
+ * | length | 7 | 6 | 7 | 6 |
+ * | stop | 0 | 0 | 0 | 1 |
+ * +-----------+-------+-------+-------+-------+
+ *
+ * Example 3: word_size = 23, packing_mode = 1 x 32, msb_to_lsb = 1
+ *
+ * +-----------+-------+-------+-------+-------+
+ * | | vec_0 | vec_1 | vec_2 | vec_3 |
+ * +-----------+-------+-------+-------+-------+
+ * | start | 0x16 | 0xe | 0x6 | 0x0 |
+ * | direction | 1 | 1 | 1 | 1 |
+ * | length | 7 | 7 | 6 | 0 |
+ * | stop | 0 | 0 | 1 | 0 |
+ * +-----------+-------+-------+-------+-------+
+ *
+ */
+
+#define NUM_PACKING_VECTORS 4
+#define PACKING_START_SHIFT 5
+#define PACKING_DIR_SHIFT 4
+#define PACKING_LEN_SHIFT 1
+#define PACKING_STOP_BIT BIT(0)
+#define PACKING_VECTOR_SHIFT 10
+/**
+ * geni_se_config_packing() - Packing configuration of the serial engine
+ * @se: Pointer to the concerned serial engine
+ * @bpw: Bits of data per transfer word.
+ * @pack_words: Number of words per fifo element.
+ * @msb_to_lsb: Transfer from MSB to LSB or vice-versa.
+ * @tx_cfg: Flag to configure the TX Packing.
+ * @rx_cfg: Flag to configure the RX Packing.
+ *
+ * This function is used to configure the packing rules for the current
+ * transfer.
+ */
+void geni_se_config_packing(struct geni_se *se, int bpw, int pack_words,
+ bool msb_to_lsb, bool tx_cfg, bool rx_cfg)
+{
+ u32 cfg0, cfg1, cfg[NUM_PACKING_VECTORS] = {0};
+ int len;
+ int temp_bpw = bpw;
+ int idx_start = msb_to_lsb ? bpw - 1 : 0;
+ int idx = idx_start;
+ int idx_delta = msb_to_lsb ? -BITS_PER_BYTE : BITS_PER_BYTE;
+ int ceil_bpw = ALIGN(bpw, BITS_PER_BYTE);
+ int iter = (ceil_bpw * pack_words) / BITS_PER_BYTE;
+ int i;
+
+ if (iter <= 0 || iter > NUM_PACKING_VECTORS)
+ return;
+
+ for (i = 0; i < iter; i++) {
+ len = min_t(int, temp_bpw, BITS_PER_BYTE) - 1;
+ cfg[i] = idx << PACKING_START_SHIFT;
+ cfg[i] |= msb_to_lsb << PACKING_DIR_SHIFT;
+ cfg[i] |= len << PACKING_LEN_SHIFT;
+
+ if (temp_bpw <= BITS_PER_BYTE) {
+ idx = ((i + 1) * BITS_PER_BYTE) + idx_start;
+ temp_bpw = bpw;
+ } else {
+ idx = idx + idx_delta;
+ temp_bpw = temp_bpw - BITS_PER_BYTE;
+ }
+ }
+ cfg[iter - 1] |= PACKING_STOP_BIT;
+ cfg0 = cfg[0] | (cfg[1] << PACKING_VECTOR_SHIFT);
+ cfg1 = cfg[2] | (cfg[3] << PACKING_VECTOR_SHIFT);
+
+ if (tx_cfg) {
+ writel_relaxed(cfg0, se->base + SE_GENI_TX_PACKING_CFG0);
+ writel_relaxed(cfg1, se->base + SE_GENI_TX_PACKING_CFG1);
+ }
+ if (rx_cfg) {
+ writel_relaxed(cfg0, se->base + SE_GENI_RX_PACKING_CFG0);
+ writel_relaxed(cfg1, se->base + SE_GENI_RX_PACKING_CFG1);
+ }
+
+ /*
+ * Number of protocol words in each FIFO entry
+ * 0 - 4x8, four words in each entry, max word size of 8 bits
+ * 1 - 2x16, two words in each entry, max word size of 16 bits
+ * 2 - 1x32, one word in each entry, max word size of 32 bits
+ * 3 - undefined
+ */
+ if (pack_words || bpw == 32)
+ writel_relaxed(bpw / 16, se->base + SE_GENI_BYTE_GRAN);
+}
+EXPORT_SYMBOL(geni_se_config_packing);
+
+static void geni_se_clks_off(struct geni_se *se)
+{
+ struct geni_wrapper *wrapper = se->wrapper;
+
+ clk_disable_unprepare(se->clk);
+ clk_bulk_disable_unprepare(ARRAY_SIZE(wrapper->ahb_clks),
+ wrapper->ahb_clks);
+}
+
+/**
+ * geni_se_resources_off() - Turn off resources associated with the serial
+ * engine
+ * @se: Pointer to the concerned serial engine.
+ *
+ * Return: 0 on success, standard Linux error codes on failure/error.
+ */
+int geni_se_resources_off(struct geni_se *se)
+{
+ int ret;
+
+ ret = pinctrl_pm_select_sleep_state(se->dev);
+ if (ret)
+ return ret;
+
+ geni_se_clks_off(se);
+ return 0;
+}
+EXPORT_SYMBOL(geni_se_resources_off);
+
+static int geni_se_clks_on(struct geni_se *se)
+{
+ int ret;
+ struct geni_wrapper *wrapper = se->wrapper;
+
+ ret = clk_bulk_prepare_enable(ARRAY_SIZE(wrapper->ahb_clks),
+ wrapper->ahb_clks);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(se->clk);
+ if (ret)
+ clk_bulk_disable_unprepare(ARRAY_SIZE(wrapper->ahb_clks),
+ wrapper->ahb_clks);
+ return ret;
+}
+
+/**
+ * geni_se_resources_on() - Turn on resources associated with the serial
+ * engine
+ * @se: Pointer to the concerned serial engine.
+ *
+ * Return: 0 on success, standard Linux error codes on failure/error.
+ */
+int geni_se_resources_on(struct geni_se *se)
+{
+ int ret;
+
+ ret = geni_se_clks_on(se);
+ if (ret)
+ return ret;
+
+ ret = pinctrl_pm_select_default_state(se->dev);
+ if (ret)
+ geni_se_clks_off(se);
+
+ return ret;
+}
+EXPORT_SYMBOL(geni_se_resources_on);
+
+/**
+ * geni_se_clk_tbl_get() - Get the clock table to program DFS
+ * @se: Pointer to the concerned serial engine.
+ * @tbl: Table in which the output is returned.
+ *
+ * This function is called by the protocol drivers to determine the different
+ * clock frequencies supported by serial engine core clock. The protocol
+ * drivers use the output to determine the clock frequency index to be
+ * programmed into DFS.
+ *
+ * Return: number of valid performance levels in the table on success,
+ * standard Linux error codes on failure.
+ */
+int geni_se_clk_tbl_get(struct geni_se *se, unsigned long **tbl)
+{
+ unsigned long freq = 0;
+ int i;
+
+ if (se->clk_perf_tbl) {
+ *tbl = se->clk_perf_tbl;
+ return se->num_clk_levels;
+ }
+
+ se->clk_perf_tbl = devm_kcalloc(se->dev, MAX_CLK_PERF_LEVEL,
+ sizeof(*se->clk_perf_tbl),
+ GFP_KERNEL);
+ if (!se->clk_perf_tbl)
+ return -ENOMEM;
+
+ for (i = 0; i < MAX_CLK_PERF_LEVEL; i++) {
+ freq = clk_round_rate(se->clk, freq + 1);
+ if (!freq || freq == se->clk_perf_tbl[i - 1])
+ break;
+ se->clk_perf_tbl[i] = freq;
+ }
+ se->num_clk_levels = i;
+ *tbl = se->clk_perf_tbl;
+ return se->num_clk_levels;
+}
+EXPORT_SYMBOL(geni_se_clk_tbl_get);
+
+/**
+ * geni_se_clk_freq_match() - Get the matching or closest SE clock frequency
+ * @se: Pointer to the concerned serial engine.
+ * @req_freq: Requested clock frequency.
+ * @index: Index of the resultant frequency in the table.
+ * @res_freq: Resultant frequency which matches or is closer to the
+ * requested frequency.
+ * @exact: Flag to indicate exact multiple requirement of the requested
+ * frequency.
+ *
+ * This function is called by the protocol drivers to determine the matching
+ * or exact multiple of the requested frequency, as provided by the serial
+ * engine clock in order to meet the performance requirements. If there is
+ * no matching or exact multiple of the requested frequency found, then it
+ * selects the closest floor frequency, if exact flag is not set.
+ *
+ * Return: 0 on success, standard Linux error codes on failure.
+ */
+int geni_se_clk_freq_match(struct geni_se *se, unsigned long req_freq,
+ unsigned int *index, unsigned long *res_freq,
+ bool exact)
+{
+ unsigned long *tbl;
+ int num_clk_levels;
+ int i;
+
+ num_clk_levels = geni_se_clk_tbl_get(se, &tbl);
+ if (num_clk_levels < 0)
+ return num_clk_levels;
+
+ if (num_clk_levels == 0)
+ return -EINVAL;
+
+ *res_freq = 0;
+ for (i = 0; i < num_clk_levels; i++) {
+ if (!(tbl[i] % req_freq)) {
+ *index = i;
+ *res_freq = tbl[i];
+ return 0;
+ }
+
+ if (!(*res_freq) || ((tbl[i] > *res_freq) &&
+ (tbl[i] < req_freq))) {
+ *index = i;
+ *res_freq = tbl[i];
+ }
+ }
+
+ if (exact)
+ return -EINVAL;
+
+ return 0;
+}
+EXPORT_SYMBOL(geni_se_clk_freq_match);
+
+#define GENI_SE_DMA_DONE_EN BIT(0)
+#define GENI_SE_DMA_EOT_EN BIT(1)
+#define GENI_SE_DMA_AHB_ERR_EN BIT(2)
+#define GENI_SE_DMA_EOT_BUF BIT(0)
+/**
+ * geni_se_tx_dma_prep() - Prepare the serial engine for TX DMA transfer
+ * @se: Pointer to the concerned serial engine.
+ * @buf: Pointer to the TX buffer.
+ * @len: Length of the TX buffer.
+ * @iova: Pointer to store the mapped DMA address.
+ *
+ * This function is used to prepare the buffers for DMA TX.
+ *
+ * Return: 0 on success, standard Linux error codes on failure.
+ */
+int geni_se_tx_dma_prep(struct geni_se *se, void *buf, size_t len,
+ dma_addr_t *iova)
+{
+ struct geni_wrapper *wrapper = se->wrapper;
+ u32 val;
+
+ *iova = dma_map_single(wrapper->dev, buf, len, DMA_TO_DEVICE);
+ if (dma_mapping_error(wrapper->dev, *iova))
+ return -EIO;
+
+ val = GENI_SE_DMA_DONE_EN;
+ val |= GENI_SE_DMA_EOT_EN;
+ val |= GENI_SE_DMA_AHB_ERR_EN;
+ writel_relaxed(val, se->base + SE_DMA_TX_IRQ_EN_SET);
+ writel_relaxed(lower_32_bits(*iova), se->base + SE_DMA_TX_PTR_L);
+ writel_relaxed(upper_32_bits(*iova), se->base + SE_DMA_TX_PTR_H);
+ writel_relaxed(GENI_SE_DMA_EOT_BUF, se->base + SE_DMA_TX_ATTR);
+ writel_relaxed(len, se->base + SE_DMA_TX_LEN);
+ return 0;
+}
+EXPORT_SYMBOL(geni_se_tx_dma_prep);
+
+/**
+ * geni_se_rx_dma_prep() - Prepare the serial engine for RX DMA transfer
+ * @se: Pointer to the concerned serial engine.
+ * @buf: Pointer to the RX buffer.
+ * @len: Length of the RX buffer.
+ * @iova: Pointer to store the mapped DMA address.
+ *
+ * This function is used to prepare the buffers for DMA RX.
+ *
+ * Return: 0 on success, standard Linux error codes on failure.
+ */
+int geni_se_rx_dma_prep(struct geni_se *se, void *buf, size_t len,
+ dma_addr_t *iova)
+{
+ struct geni_wrapper *wrapper = se->wrapper;
+ u32 val;
+
+ *iova = dma_map_single(wrapper->dev, buf, len, DMA_FROM_DEVICE);
+ if (dma_mapping_error(wrapper->dev, *iova))
+ return -EIO;
+
+ val = GENI_SE_DMA_DONE_EN;
+ val |= GENI_SE_DMA_EOT_EN;
+ val |= GENI_SE_DMA_AHB_ERR_EN;
+ writel_relaxed(val, se->base + SE_DMA_RX_IRQ_EN_SET);
+ writel_relaxed(lower_32_bits(*iova), se->base + SE_DMA_RX_PTR_L);
+ writel_relaxed(upper_32_bits(*iova), se->base + SE_DMA_RX_PTR_H);
+ /* RX does not have EOT buffer type bit. So just reset RX_ATTR */
+ writel_relaxed(0, se->base + SE_DMA_RX_ATTR);
+ writel_relaxed(len, se->base + SE_DMA_RX_LEN);
+ return 0;
+}
+EXPORT_SYMBOL(geni_se_rx_dma_prep);
+
+/**
+ * geni_se_tx_dma_unprep() - Unprepare the serial engine after TX DMA transfer
+ * @se: Pointer to the concerned serial engine.
+ * @iova: DMA address of the TX buffer.
+ * @len: Length of the TX buffer.
+ *
+ * This function is used to unprepare the DMA buffers after DMA TX.
+ */
+void geni_se_tx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len)
+{
+ struct geni_wrapper *wrapper = se->wrapper;
+
+ if (iova && !dma_mapping_error(wrapper->dev, iova))
+ dma_unmap_single(wrapper->dev, iova, len, DMA_TO_DEVICE);
+}
+EXPORT_SYMBOL(geni_se_tx_dma_unprep);
+
+/**
+ * geni_se_rx_dma_unprep() - Unprepare the serial engine after RX DMA transfer
+ * @se: Pointer to the concerned serial engine.
+ * @iova: DMA address of the RX buffer.
+ * @len: Length of the RX buffer.
+ *
+ * This function is used to unprepare the DMA buffers after DMA RX.
+ */
+void geni_se_rx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len)
+{
+ struct geni_wrapper *wrapper = se->wrapper;
+
+ if (iova && !dma_mapping_error(wrapper->dev, iova))
+ dma_unmap_single(wrapper->dev, iova, len, DMA_FROM_DEVICE);
+}
+EXPORT_SYMBOL(geni_se_rx_dma_unprep);
+
+static int geni_se_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct geni_wrapper *wrapper;
+ int ret;
+
+ wrapper = devm_kzalloc(dev, sizeof(*wrapper), GFP_KERNEL);
+ if (!wrapper)
+ return -ENOMEM;
+
+ wrapper->dev = dev;
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ wrapper->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(wrapper->base))
+ return PTR_ERR(wrapper->base);
+
+ wrapper->ahb_clks[0].id = "m-ahb";
+ wrapper->ahb_clks[1].id = "s-ahb";
+ ret = devm_clk_bulk_get(dev, NUM_AHB_CLKS, wrapper->ahb_clks);
+ if (ret) {
+ dev_err(dev, "Err getting AHB clks %d\n", ret);
+ return ret;
+ }
+
+ dev_set_drvdata(dev, wrapper);
+ dev_dbg(dev, "GENI SE Driver probed\n");
+ return devm_of_platform_populate(dev);
+}
+
+static const struct of_device_id geni_se_dt_match[] = {
+ { .compatible = "qcom,geni-se-qup", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, geni_se_dt_match);
+
+static struct platform_driver geni_se_driver = {
+ .driver = {
+ .name = "geni_se_qup",
+ .of_match_table = geni_se_dt_match,
+ },
+ .probe = geni_se_probe,
+};
+module_platform_driver(geni_se_driver);
+
+MODULE_DESCRIPTION("GENI Serial Engine Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/qcom-geni-se.h b/include/linux/qcom-geni-se.h
new file mode 100644
index 000000000000..5d6144977828
--- /dev/null
+++ b/include/linux/qcom-geni-se.h
@@ -0,0 +1,425 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * Copyright (c) 2017-2018, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _LINUX_QCOM_GENI_SE
+#define _LINUX_QCOM_GENI_SE
+
+/* Transfer mode supported by GENI Serial Engines */
+enum geni_se_xfer_mode {
+ GENI_SE_INVALID,
+ GENI_SE_FIFO,
+ GENI_SE_DMA,
+};
+
+/* Protocols supported by GENI Serial Engines */
+enum geni_se_protocol_type {
+ GENI_SE_NONE,
+ GENI_SE_SPI,
+ GENI_SE_UART,
+ GENI_SE_I2C,
+ GENI_SE_I3C,
+};
+
+struct geni_wrapper;
+struct clk;
+
+/**
+ * struct geni_se - GENI Serial Engine
+ * @base: Base Address of the Serial Engine's register block
+ * @dev: Pointer to the Serial Engine device
+ * @wrapper: Pointer to the parent QUP Wrapper core
+ * @clk: Handle to the core serial engine clock
+ * @num_clk_levels: Number of valid clock levels in clk_perf_tbl
+ * @clk_perf_tbl: Table of clock frequency input to serial engine clock
+ */
+struct geni_se {
+ void __iomem *base;
+ struct device *dev;
+ struct geni_wrapper *wrapper;
+ struct clk *clk;
+ unsigned int num_clk_levels;
+ unsigned long *clk_perf_tbl;
+};
+
+/* Common SE registers */
+#define GENI_FORCE_DEFAULT_REG 0x20
+#define SE_GENI_STATUS 0x40
+#define GENI_SER_M_CLK_CFG 0x48
+#define GENI_SER_S_CLK_CFG 0x4c
+#define GENI_FW_REVISION_RO 0x68
+#define SE_GENI_CLK_SEL 0x7c
+#define SE_GENI_DMA_MODE_EN 0x258
+#define SE_GENI_M_CMD0 0x600
+#define SE_GENI_M_CMD_CTRL_REG 0x604
+#define SE_GENI_M_IRQ_STATUS 0x610
+#define SE_GENI_M_IRQ_EN 0x614
+#define SE_GENI_M_IRQ_CLEAR 0x618
+#define SE_GENI_S_CMD0 0x630
+#define SE_GENI_S_CMD_CTRL_REG 0x634
+#define SE_GENI_S_IRQ_STATUS 0x640
+#define SE_GENI_S_IRQ_EN 0x644
+#define SE_GENI_S_IRQ_CLEAR 0x648
+#define SE_GENI_TX_FIFOn 0x700
+#define SE_GENI_RX_FIFOn 0x780
+#define SE_GENI_TX_FIFO_STATUS 0x800
+#define SE_GENI_RX_FIFO_STATUS 0x804
+#define SE_GENI_TX_WATERMARK_REG 0x80c
+#define SE_GENI_RX_WATERMARK_REG 0x810
+#define SE_GENI_RX_RFR_WATERMARK_REG 0x814
+#define SE_GENI_IOS 0x908
+#define SE_DMA_TX_IRQ_STAT 0xc40
+#define SE_DMA_TX_IRQ_CLR 0xc44
+#define SE_DMA_TX_FSM_RST 0xc58
+#define SE_DMA_RX_IRQ_STAT 0xd40
+#define SE_DMA_RX_IRQ_CLR 0xd44
+#define SE_DMA_RX_FSM_RST 0xd58
+#define SE_HW_PARAM_0 0xe24
+#define SE_HW_PARAM_1 0xe28
+
+/* GENI_FORCE_DEFAULT_REG fields */
+#define FORCE_DEFAULT BIT(0)
+
+/* GENI_STATUS fields */
+#define M_GENI_CMD_ACTIVE BIT(0)
+#define S_GENI_CMD_ACTIVE BIT(12)
+
+/* GENI_SER_M_CLK_CFG/GENI_SER_S_CLK_CFG */
+#define SER_CLK_EN BIT(0)
+#define CLK_DIV_MSK GENMASK(15, 4)
+#define CLK_DIV_SHFT 4
+
+/* GENI_FW_REVISION_RO fields */
+#define FW_REV_PROTOCOL_MSK GENMASK(15, 8)
+#define FW_REV_PROTOCOL_SHFT 8
+
+/* GENI_CLK_SEL fields */
+#define CLK_SEL_MSK GENMASK(2, 0)
+
+/* SE_GENI_DMA_MODE_EN */
+#define GENI_DMA_MODE_EN BIT(0)
+
+/* GENI_M_CMD0 fields */
+#define M_OPCODE_MSK GENMASK(31, 27)
+#define M_OPCODE_SHFT 27
+#define M_PARAMS_MSK GENMASK(26, 0)
+
+/* GENI_M_CMD_CTRL_REG */
+#define M_GENI_CMD_CANCEL BIT(2)
+#define M_GENI_CMD_ABORT BIT(1)
+#define M_GENI_DISABLE BIT(0)
+
+/* GENI_S_CMD0 fields */
+#define S_OPCODE_MSK GENMASK(31, 27)
+#define S_OPCODE_SHFT 27
+#define S_PARAMS_MSK GENMASK(26, 0)
+
+/* GENI_S_CMD_CTRL_REG */
+#define S_GENI_CMD_CANCEL BIT(2)
+#define S_GENI_CMD_ABORT BIT(1)
+#define S_GENI_DISABLE BIT(0)
+
+/* GENI_M_IRQ_EN fields */
+#define M_CMD_DONE_EN BIT(0)
+#define M_CMD_OVERRUN_EN BIT(1)
+#define M_ILLEGAL_CMD_EN BIT(2)
+#define M_CMD_FAILURE_EN BIT(3)
+#define M_CMD_CANCEL_EN BIT(4)
+#define M_CMD_ABORT_EN BIT(5)
+#define M_TIMESTAMP_EN BIT(6)
+#define M_RX_IRQ_EN BIT(7)
+#define M_GP_SYNC_IRQ_0_EN BIT(8)
+#define M_GP_IRQ_0_EN BIT(9)
+#define M_GP_IRQ_1_EN BIT(10)
+#define M_GP_IRQ_2_EN BIT(11)
+#define M_GP_IRQ_3_EN BIT(12)
+#define M_GP_IRQ_4_EN BIT(13)
+#define M_GP_IRQ_5_EN BIT(14)
+#define M_IO_DATA_DEASSERT_EN BIT(22)
+#define M_IO_DATA_ASSERT_EN BIT(23)
+#define M_RX_FIFO_RD_ERR_EN BIT(24)
+#define M_RX_FIFO_WR_ERR_EN BIT(25)
+#define M_RX_FIFO_WATERMARK_EN BIT(26)
+#define M_RX_FIFO_LAST_EN BIT(27)
+#define M_TX_FIFO_RD_ERR_EN BIT(28)
+#define M_TX_FIFO_WR_ERR_EN BIT(29)
+#define M_TX_FIFO_WATERMARK_EN BIT(30)
+#define M_SEC_IRQ_EN BIT(31)
+#define M_COMMON_GENI_M_IRQ_EN (GENMASK(6, 1) | \
+ M_IO_DATA_DEASSERT_EN | \
+ M_IO_DATA_ASSERT_EN | M_RX_FIFO_RD_ERR_EN | \
+ M_RX_FIFO_WR_ERR_EN | M_TX_FIFO_RD_ERR_EN | \
+ M_TX_FIFO_WR_ERR_EN)
+
+/* GENI_S_IRQ_EN fields */
+#define S_CMD_DONE_EN BIT(0)
+#define S_CMD_OVERRUN_EN BIT(1)
+#define S_ILLEGAL_CMD_EN BIT(2)
+#define S_CMD_FAILURE_EN BIT(3)
+#define S_CMD_CANCEL_EN BIT(4)
+#define S_CMD_ABORT_EN BIT(5)
+#define S_GP_SYNC_IRQ_0_EN BIT(8)
+#define S_GP_IRQ_0_EN BIT(9)
+#define S_GP_IRQ_1_EN BIT(10)
+#define S_GP_IRQ_2_EN BIT(11)
+#define S_GP_IRQ_3_EN BIT(12)
+#define S_GP_IRQ_4_EN BIT(13)
+#define S_GP_IRQ_5_EN BIT(14)
+#define S_IO_DATA_DEASSERT_EN BIT(22)
+#define S_IO_DATA_ASSERT_EN BIT(23)
+#define S_RX_FIFO_RD_ERR_EN BIT(24)
+#define S_RX_FIFO_WR_ERR_EN BIT(25)
+#define S_RX_FIFO_WATERMARK_EN BIT(26)
+#define S_RX_FIFO_LAST_EN BIT(27)
+#define S_COMMON_GENI_S_IRQ_EN (GENMASK(5, 1) | GENMASK(13, 9) | \
+ S_RX_FIFO_RD_ERR_EN | S_RX_FIFO_WR_ERR_EN)
+
+/* GENI_/TX/RX/RX_RFR/_WATERMARK_REG fields */
+#define WATERMARK_MSK GENMASK(5, 0)
+
+/* GENI_TX_FIFO_STATUS fields */
+#define TX_FIFO_WC GENMASK(27, 0)
+
+/* GENI_RX_FIFO_STATUS fields */
+#define RX_LAST BIT(31)
+#define RX_LAST_BYTE_VALID_MSK GENMASK(30, 28)
+#define RX_LAST_BYTE_VALID_SHFT 28
+#define RX_FIFO_WC_MSK GENMASK(24, 0)
+
+/* SE_GENI_IOS fields */
+#define IO2_DATA_IN BIT(1)
+#define RX_DATA_IN BIT(0)
+
+/* SE_DMA_TX_IRQ_STAT Register fields */
+#define TX_DMA_DONE BIT(0)
+#define TX_EOT BIT(1)
+#define TX_SBE BIT(2)
+#define TX_RESET_DONE BIT(3)
+
+/* SE_DMA_RX_IRQ_STAT Register fields */
+#define RX_DMA_DONE BIT(0)
+#define RX_EOT BIT(1)
+#define RX_SBE BIT(2)
+#define RX_RESET_DONE BIT(3)
+#define RX_FLUSH_DONE BIT(4)
+#define RX_GENI_GP_IRQ GENMASK(10, 5)
+#define RX_GENI_CANCEL_IRQ BIT(11)
+#define RX_GENI_GP_IRQ_EXT GENMASK(13, 12)
+
+/* SE_HW_PARAM_0 fields */
+#define TX_FIFO_WIDTH_MSK GENMASK(29, 24)
+#define TX_FIFO_WIDTH_SHFT 24
+#define TX_FIFO_DEPTH_MSK GENMASK(21, 16)
+#define TX_FIFO_DEPTH_SHFT 16
+
+/* SE_HW_PARAM_1 fields */
+#define RX_FIFO_WIDTH_MSK GENMASK(29, 24)
+#define RX_FIFO_WIDTH_SHFT 24
+#define RX_FIFO_DEPTH_MSK GENMASK(21, 16)
+#define RX_FIFO_DEPTH_SHFT 16
+
+#define HW_VER_MAJOR_MASK GENMASK(31, 28)
+#define HW_VER_MAJOR_SHFT 28
+#define HW_VER_MINOR_MASK GENMASK(27, 16)
+#define HW_VER_MINOR_SHFT 16
+#define HW_VER_STEP_MASK GENMASK(15, 0)
+
+#if IS_ENABLED(CONFIG_QCOM_GENI_SE)
+
+u32 geni_se_get_qup_hw_version(struct geni_se *se);
+
+#define geni_se_get_wrapper_version(se, major, minor, step) do { \
+ u32 ver; \
+\
+ ver = geni_se_get_qup_hw_version(se); \
+ major = (ver & HW_VER_MAJOR_MASK) >> HW_VER_MAJOR_SHFT; \
+ minor = (ver & HW_VER_MINOR_MASK) >> HW_VER_MINOR_SHFT; \
+ step = version & HW_VER_STEP_MASK; \
+} while (0)
+
+/**
+ * geni_se_read_proto() - Read the protocol configured for a serial engine
+ * @se: Pointer to the concerned serial engine.
+ *
+ * Return: Protocol value as configured in the serial engine.
+ */
+static inline u32 geni_se_read_proto(struct geni_se *se)
+{
+ u32 val;
+
+ val = readl_relaxed(se->base + GENI_FW_REVISION_RO);
+
+ return (val & FW_REV_PROTOCOL_MSK) >> FW_REV_PROTOCOL_SHFT;
+}
+
+/**
+ * geni_se_setup_m_cmd() - Setup the primary sequencer
+ * @se: Pointer to the concerned serial engine.
+ * @cmd: Command/Operation to setup in the primary sequencer.
+ * @params: Parameter for the sequencer command.
+ *
+ * This function is used to configure the primary sequencer with the
+ * command and its associated parameters.
+ */
+static inline void geni_se_setup_m_cmd(struct geni_se *se, u32 cmd, u32 params)
+{
+ u32 m_cmd;
+
+ m_cmd = (cmd << M_OPCODE_SHFT) | (params & M_PARAMS_MSK);
+ writel_relaxed(m_cmd, se->base + SE_GENI_M_CMD0);
+}
+
+/**
+ * geni_se_setup_s_cmd() - Setup the secondary sequencer
+ * @se: Pointer to the concerned serial engine.
+ * @cmd: Command/Operation to setup in the secondary sequencer.
+ * @params: Parameter for the sequencer command.
+ *
+ * This function is used to configure the secondary sequencer with the
+ * command and its associated parameters.
+ */
+static inline void geni_se_setup_s_cmd(struct geni_se *se, u32 cmd, u32 params)
+{
+ u32 s_cmd;
+
+ s_cmd = readl_relaxed(se->base + SE_GENI_S_CMD0);
+ s_cmd &= ~(S_OPCODE_MSK | S_PARAMS_MSK);
+ s_cmd |= (cmd << S_OPCODE_SHFT);
+ s_cmd |= (params & S_PARAMS_MSK);
+ writel_relaxed(s_cmd, se->base + SE_GENI_S_CMD0);
+}
+
+/**
+ * geni_se_cancel_m_cmd() - Cancel the command configured in the primary
+ * sequencer
+ * @se: Pointer to the concerned serial engine.
+ *
+ * This function is used to cancel the currently configured command in the
+ * primary sequencer.
+ */
+static inline void geni_se_cancel_m_cmd(struct geni_se *se)
+{
+ writel_relaxed(M_GENI_CMD_CANCEL, se->base + SE_GENI_M_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_cancel_s_cmd() - Cancel the command configured in the secondary
+ * sequencer
+ * @se: Pointer to the concerned serial engine.
+ *
+ * This function is used to cancel the currently configured command in the
+ * secondary sequencer.
+ */
+static inline void geni_se_cancel_s_cmd(struct geni_se *se)
+{
+ writel_relaxed(S_GENI_CMD_CANCEL, se->base + SE_GENI_S_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_abort_m_cmd() - Abort the command configured in the primary sequencer
+ * @se: Pointer to the concerned serial engine.
+ *
+ * This function is used to force abort the currently configured command in the
+ * primary sequencer.
+ */
+static inline void geni_se_abort_m_cmd(struct geni_se *se)
+{
+ writel_relaxed(M_GENI_CMD_ABORT, se->base + SE_GENI_M_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_abort_s_cmd() - Abort the command configured in the secondary
+ * sequencer
+ * @se: Pointer to the concerned serial engine.
+ *
+ * This function is used to force abort the currently configured command in the
+ * secondary sequencer.
+ */
+static inline void geni_se_abort_s_cmd(struct geni_se *se)
+{
+ writel_relaxed(S_GENI_CMD_ABORT, se->base + SE_GENI_S_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_get_tx_fifo_depth() - Get the TX fifo depth of the serial engine
+ * @se: Pointer to the concerned serial engine.
+ *
+ * This function is used to get the depth i.e. number of elements in the
+ * TX fifo of the serial engine.
+ *
+ * Return: TX fifo depth in units of FIFO words.
+ */
+static inline u32 geni_se_get_tx_fifo_depth(struct geni_se *se)
+{
+ u32 val;
+
+ val = readl_relaxed(se->base + SE_HW_PARAM_0);
+
+ return (val & TX_FIFO_DEPTH_MSK) >> TX_FIFO_DEPTH_SHFT;
+}
+
+/**
+ * geni_se_get_tx_fifo_width() - Get the TX fifo width of the serial engine
+ * @se: Pointer to the concerned serial engine.
+ *
+ * This function is used to get the width i.e. word size per element in the
+ * TX fifo of the serial engine.
+ *
+ * Return: TX fifo width in bits
+ */
+static inline u32 geni_se_get_tx_fifo_width(struct geni_se *se)
+{
+ u32 val;
+
+ val = readl_relaxed(se->base + SE_HW_PARAM_0);
+
+ return (val & TX_FIFO_WIDTH_MSK) >> TX_FIFO_WIDTH_SHFT;
+}
+
+/**
+ * geni_se_get_rx_fifo_depth() - Get the RX fifo depth of the serial engine
+ * @se: Pointer to the concerned serial engine.
+ *
+ * This function is used to get the depth i.e. number of elements in the
+ * RX fifo of the serial engine.
+ *
+ * Return: RX fifo depth in units of FIFO words
+ */
+static inline u32 geni_se_get_rx_fifo_depth(struct geni_se *se)
+{
+ u32 val;
+
+ val = readl_relaxed(se->base + SE_HW_PARAM_1);
+
+ return (val & RX_FIFO_DEPTH_MSK) >> RX_FIFO_DEPTH_SHFT;
+}
+
+void geni_se_init(struct geni_se *se, u32 rx_wm, u32 rx_rfr);
+
+void geni_se_select_mode(struct geni_se *se, enum geni_se_xfer_mode mode);
+
+void geni_se_config_packing(struct geni_se *se, int bpw, int pack_words,
+ bool msb_to_lsb, bool tx_cfg, bool rx_cfg);
+
+int geni_se_resources_off(struct geni_se *se);
+
+int geni_se_resources_on(struct geni_se *se);
+
+int geni_se_clk_tbl_get(struct geni_se *se, unsigned long **tbl);
+
+int geni_se_clk_freq_match(struct geni_se *se, unsigned long req_freq,
+ unsigned int *index, unsigned long *res_freq,
+ bool exact);
+
+int geni_se_tx_dma_prep(struct geni_se *se, void *buf, size_t len,
+ dma_addr_t *iova);
+
+int geni_se_rx_dma_prep(struct geni_se *se, void *buf, size_t len,
+ dma_addr_t *iova);
+
+void geni_se_tx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len);
+
+void geni_se_rx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len);
+#endif
+#endif