diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media')
3 files changed, 157 insertions, 93 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt deleted file mode 100644 index c97c2f2da12d..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt +++ /dev/null @@ -1,92 +0,0 @@ -* Omnivision OV5640 MIPI CSI-2 / parallel sensor - -Required Properties: -- compatible: should be "ovti,ov5640" -- clocks: reference to the xclk input clock. -- clock-names: should be "xclk". -- DOVDD-supply: Digital I/O voltage supply, 1.8 volts -- AVDD-supply: Analog voltage supply, 2.8 volts -- DVDD-supply: Digital core voltage supply, 1.5 volts - -Optional Properties: -- reset-gpios: reference to the GPIO connected to the reset pin, if any. - This is an active low signal to the OV5640. -- powerdown-gpios: reference to the GPIO connected to the powerdown pin, - if any. This is an active high signal to the OV5640. -- rotation: as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt, - valid values are 0 (sensor mounted upright) and 180 (sensor - mounted upside down). - -The device node must contain one 'port' child node for its digital output -video port, in accordance with the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. - -OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint. - -Endpoint node required properties for CSI-2 connection are: -- remote-endpoint: a phandle to the bus receiver's endpoint node. -- clock-lanes: should be set to <0> (clock lane on hardware lane 0) -- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported) - -Endpoint node required properties for parallel connection are: -- remote-endpoint: a phandle to the bus receiver's endpoint node. -- bus-width: shall be set to <8> for 8 bits parallel bus - or <10> for 10 bits parallel bus -- data-shift: shall be set to <2> for 8 bits parallel bus - (lines 9:2 are used) or <0> for 10 bits parallel bus -- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. -- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. -- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock - signal. - -Examples: - -&i2c1 { - ov5640: camera@3c { - compatible = "ovti,ov5640"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ov5640>; - reg = <0x3c>; - clocks = <&clks IMX6QDL_CLK_CKO>; - clock-names = "xclk"; - DOVDD-supply = <&vgen4_reg>; /* 1.8v */ - AVDD-supply = <&vgen3_reg>; /* 2.8v */ - DVDD-supply = <&vgen2_reg>; /* 1.5v */ - powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; - rotation = <180>; - - port { - /* MIPI CSI-2 bus endpoint */ - ov5640_to_mipi_csi2: endpoint { - remote-endpoint = <&mipi_csi2_from_ov5640>; - clock-lanes = <0>; - data-lanes = <1 2>; - }; - }; - }; -}; - -&i2c1 { - ov5640: camera@3c { - compatible = "ovti,ov5640"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ov5640>; - reg = <0x3c>; - clocks = <&clk_ext_camera>; - clock-names = "xclk"; - - port { - /* Parallel bus endpoint */ - ov5640_to_parallel: endpoint { - remote-endpoint = <¶llel_from_ov5640>; - bus-width = <8>; - data-shift = <2>; /* lines 9:2 are used */ - hsync-active = <0>; - vsync-active = <0>; - pclk-sample = <1>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml new file mode 100644 index 000000000000..540fd69ac39f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml @@ -0,0 +1,154 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5640.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV5640 Image Sensor Device Tree Bindings + +maintainers: + - Steve Longerbeam <slongerbeam@gmail.com> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov5640 + + reg: + maxItems: 1 + + clocks: + description: XCLK Input Clock + + clock-names: + const: xclk + + AVDD-supply: + description: Analog voltage supply, 2.8 volts + + DVDD-supply: + description: Digital core voltage supply, 1.5 volts + + DOVDD-supply: + description: Digital I/O voltage supply, 1.8 volts + + powerdown-gpios: + maxItems: 1 + description: > + Reference to the GPIO connected to the powerdown pin, if any. + + reset-gpios: + maxItems: 1 + description: > + Reference to the GPIO connected to the reset pin, if any. + + rotation: + enum: + - 0 + - 180 + + port: + description: Digital Output Port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + const: 0 + + data-lanes: + minItems: 1 + maxItems: 2 + items: + enum: [1, 2] + + bus-width: + enum: [8, 10] + + data-shift: + enum: [0, 2] + +required: + - compatible + - reg + - clocks + - clock-names + - AVDD-supply + - DVDD-supply + - DOVDD-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx6qdl-clock.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clks IMX6QDL_CLK_CKO>; + clock-names = "xclk"; + DOVDD-supply = <&vgen4_reg>; /* 1.8v */ + AVDD-supply = <&vgen3_reg>; /* 2.8v */ + DVDD-supply = <&vgen2_reg>; /* 1.5v */ + powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + rotation = <180>; + + port { + /* MIPI CSI-2 bus endpoint */ + ov5640_to_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_from_ov5640>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; + }; + + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + clock-names = "xclk"; + DOVDD-supply = <&vgen4_reg>; /* 1.8v */ + AVDD-supply = <&vgen3_reg>; /* 2.8v */ + DVDD-supply = <&vgen2_reg>; /* 1.5v */ + + port { + /* Parallel bus endpoint */ + ov5640_to_parallel: endpoint { + remote-endpoint = <¶llel_from_ov5640>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/ti,cal.yaml b/Documentation/devicetree/bindings/media/ti,cal.yaml index 65177cd69514..66c5d392fa75 100644 --- a/Documentation/devicetree/bindings/media/ti,cal.yaml +++ b/Documentation/devicetree/bindings/media/ti,cal.yaml @@ -154,7 +154,9 @@ examples: camera-sensor@3c { compatible = "ovti,ov5640"; reg = <0x3c>; - + AVDD-supply = <®_2p8v>; + DOVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p5v>; clocks = <&clk_ov5640_fixed>; clock-names = "xclk"; |