diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd')
14 files changed, 253 insertions, 15 deletions
diff --git a/Documentation/devicetree/bindings/mfd/act8945a.txt b/Documentation/devicetree/bindings/mfd/act8945a.txt index 462819ac3da8..e6f168db6c72 100644 --- a/Documentation/devicetree/bindings/mfd/act8945a.txt +++ b/Documentation/devicetree/bindings/mfd/act8945a.txt @@ -12,7 +12,6 @@ Example: pmic@5b { compatible = "active-semi,act8945a"; reg = <0x5b>; - status = "okay"; active-semi,vsel-high; @@ -79,6 +78,5 @@ Example: active-semi,input-voltage-threshold-microvolt = <6600>; active-semi,precondition-timeout = <40>; active-semi,total-timeout = <3>; - status = "okay"; }; }; diff --git a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt index eec40be7f79a..3f643ef121ff 100644 --- a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt +++ b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt @@ -25,7 +25,6 @@ Example: clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; clock-names = "periph_clk","sys_clk", "slow_clk"; interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; - status = "disabled"; hlcdc-display-controller { compatible = "atmel,hlcdc-display-controller"; diff --git a/Documentation/devicetree/bindings/mfd/atmel-smc.txt b/Documentation/devicetree/bindings/mfd/atmel-smc.txt index 26eeed373934..1103ce2030fb 100644 --- a/Documentation/devicetree/bindings/mfd/atmel-smc.txt +++ b/Documentation/devicetree/bindings/mfd/atmel-smc.txt @@ -8,6 +8,7 @@ Required properties: - compatible: Should be one of the following "atmel,at91sam9260-smc", "syscon" "atmel,sama5d3-smc", "syscon" + "atmel,sama5d2-smc", "syscon" - reg: Contains offset/length value of the SMC memory region. diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index aca09af66514..9455503b0299 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -7,7 +7,14 @@ axp209 (X-Powers) axp221 (X-Powers) axp223 (X-Powers) axp803 (X-Powers) +axp806 (X-Powers) axp809 (X-Powers) +axp813 (X-Powers) + +The AXP813 is 2 chips packaged into 1. The 2 chips do not share anything +other than the packaging. Pins are routed separately. As such they should +be treated as separate entities. The other half is an AC100 RTC/codec +combo chip. Please see ./ac100.txt for its bindings. Required properties: - compatible: should be one of: @@ -19,6 +26,7 @@ Required properties: * "x-powers,axp803" * "x-powers,axp806" * "x-powers,axp809" + * "x-powers,axp813" - reg: The I2C slave address or RSB hardware address for the AXP chip - interrupt-parent: The parent interrupt controller - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin @@ -28,12 +36,14 @@ Required properties: Optional properties: - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz AXP152/20X: range: 750-1875, Default: 1.5 MHz - AXP22X/80X: range: 1800-4050, Default: 3 MHz + AXP22X/8XX: range: 1800-4050, Default: 3 MHz -- x-powers,drive-vbus-en: axp221 / axp223 only boolean, set this when the - N_VBUSEN pin is used as an output pin to control an external - regulator to drive the OTG VBus, rather then as an input pin - which signals whether the board is driving OTG VBus or not. +- x-powers,drive-vbus-en: boolean, set this when the N_VBUSEN pin is + used as an output pin to control an external + regulator to drive the OTG VBus, rather then + as an input pin which signals whether the + board is driving OTG VBus or not. + (axp221 / axp223 / axp813 only) - x-powers,master-mode: Boolean (axp806 only). Set this when the PMIC is wired for master mode. The default is slave mode. @@ -171,6 +181,36 @@ LDO_IO1 : LDO : ips-supply : GPIO 1 RTC_LDO : LDO : ips-supply : always on SW : On/Off Switch : swin-supply +AXP813 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply : poly-phase capable +DCDC3 : DC-DC buck : vin3-supply : poly-phase capable +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply : poly-phase capable +DCDC6 : DC-DC buck : vin6-supply : poly-phase capable +DCDC7 : DC-DC buck : vin7-supply +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +DLDO3 : LDO : dldoin-supply : shared supply +DLDO4 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +FLDO1 : LDO : fldoin-supply : shared supply +FLDO2 : LDO : fldoin-supply : shared supply +FLDO3 : LDO : fldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on +SW : On/Off Switch : swin-supply +DRIVEVBUS : Enable output : drivevbus-supply : external regulator + Example: axp209: pmic@34 { diff --git a/Documentation/devicetree/bindings/mfd/bd9571mwv.txt b/Documentation/devicetree/bindings/mfd/bd9571mwv.txt new file mode 100644 index 000000000000..9ab216a851d5 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/bd9571mwv.txt @@ -0,0 +1,49 @@ +* ROHM BD9571MWV Power Management Integrated Circuit (PMIC) bindings + +Required properties: + - compatible : Should be "rohm,bd9571mwv". + - reg : I2C slave address. + - interrupt-parent : Phandle to the parent interrupt controller. + - interrupts : The interrupt line the device is connected to. + - interrupt-controller : Marks the device node as an interrupt controller. + - #interrupt-cells : The number of cells to describe an IRQ, should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as trigger + masks from ../interrupt-controller/interrupts.txt. + - gpio-controller : Marks the device node as a GPIO Controller. + - #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - regulators: : List of child nodes that specify the regulator + initialization data. Child nodes must be named + after their hardware counterparts: + - vd09 + - vd18 + - vd25 + - vd33 + - dvfs + Each child node is defined using the standard + binding for regulators. + +Example: + + pmic: pmic@30 { + compatible = "rohm,bd9571mwv"; + reg = <0x30>; + interrupt-parent = <&gpio2>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + regulators { + dvfs: dvfs { + regulator-name = "dvfs"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1030000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt index 9554292dc6cb..07c69c0c6624 100644 --- a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt +++ b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt @@ -4,6 +4,14 @@ Required properties: - compatible : Should be "dlg,da9052", "dlg,da9053-aa", "dlg,da9053-ab", or "dlg,da9053-bb" +Optional properties: +- dlg,tsi-as-adc : Boolean, if set the X+, X-, Y+, Y- touchscreen + input lines are used as general purpose analogue + input. +- tsiref-supply: Phandle to the regulator, which provides the reference + voltage for the TSIREF pin. Must be provided when the + touchscreen pins are used for ADC purposes. + Sub-nodes: - regulators : Contain the regulator nodes. The DA9052/53 regulators are bound using their names as listed below: @@ -29,7 +37,6 @@ Sub-nodes: Examples: i2c@63fc8000 { /* I2C1 */ - status = "okay"; pmic: dialog@48 { compatible = "dlg,da9053-aa"; diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt index 8aba48821a85..39ba4146769d 100644 --- a/Documentation/devicetree/bindings/mfd/mc13xxx.txt +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -116,7 +116,6 @@ ecspi@70010000 { /* ECSPI1 */ fsl,spi-num-chipselects = <2>; cs-gpios = <&gpio4 24 0>, /* GPIO4_24 */ <&gpio4 25 0>; /* GPIO4_25 */ - status = "okay"; pmic: mc13892@0 { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/mfd/mxs-lradc.txt b/Documentation/devicetree/bindings/mfd/mxs-lradc.txt index 555fb117d4fa..755cbef0647d 100644 --- a/Documentation/devicetree/bindings/mfd/mxs-lradc.txt +++ b/Documentation/devicetree/bindings/mfd/mxs-lradc.txt @@ -26,7 +26,6 @@ Example for i.MX23 SoC: compatible = "fsl,imx23-lradc"; reg = <0x80050000 0x2000>; interrupts = <36 37 38 39 40 41 42 43 44>; - status = "okay"; fsl,lradc-touchscreen-wires = <4>; fsl,ave-ctrl = <4>; fsl,ave-delay = <2>; @@ -39,7 +38,6 @@ Example for i.MX28 SoC: compatible = "fsl,imx28-lradc"; reg = <0x80050000 0x2000>; interrupts = <10 14 15 16 17 18 19 20 21 22 23 24 25>; - status = "okay"; fsl,lradc-touchscreen-wires = <5>; fsl,ave-ctrl = <4>; fsl,ave-delay = <2>; diff --git a/Documentation/devicetree/bindings/mfd/retu.txt b/Documentation/devicetree/bindings/mfd/retu.txt new file mode 100644 index 000000000000..876242394a16 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/retu.txt @@ -0,0 +1,25 @@ +* Device tree bindings for Nokia Retu and Tahvo multi-function device + +Retu and Tahvo are a multi-function devices found on Nokia Internet +Tablets (770, N800 and N810). The Retu chip provides watchdog timer +and power button control functionalities while Tahvo chip provides +USB transceiver functionality. + +Required properties: +- compatible: "nokia,retu" or "nokia,tahvo" +- reg: Specifies the CBUS slave address of the ASIC chip +- interrupts: The interrupt line the device is connected to +- interrupt-parent: The parent interrupt controller + +Example: + +cbus0 { + compatible = "i2c-cbus-gpio"; + ... + retu: retu@1 { + compatible = "nokia,retu"; + interrupt-parent = <&gpio4>; + interrupts = <12 IRQ_TYPE_EDGE_RISING>; + reg = <0x1>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt index 9636ae8d8d41..91b65227afeb 100644 --- a/Documentation/devicetree/bindings/mfd/rk808.txt +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -1,11 +1,14 @@ RK8XX Power Management Integrated Circuit The rk8xx family current members: +rk805 rk808 rk818 Required properties: -- compatible: "rockchip,rk808", "rockchip,rk818" +- compatible: "rockchip,rk805" +- compatible: "rockchip,rk808" +- compatible: "rockchip,rk818" - reg: I2C slave address - interrupt-parent: The parent interrupt controller. - interrupts: the interrupt outputs of the controller. @@ -18,6 +21,14 @@ Optional properties: - rockchip,system-power-controller: Telling whether or not this pmic is controlling the system power. +Optional RK805 properties: +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- vcc5-supply: The input supply for LDO_REG1 and LDO_REG2 +- vcc6-supply: The input supply for LDO_REG3 + Optional RK808 properties: - vcc1-supply: The input supply for DCDC_REG1 - vcc2-supply: The input supply for DCDC_REG2 @@ -56,6 +67,15 @@ by a child node of the 'regulators' node. /* standard regulator bindings here */ }; +Following regulators of the RK805 PMIC regulators are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK805 datasheet. + + - DCDC_REGn + - valid values for n are 1 to 4. + - LDO_REGn + - valid values for n are 1 to 3 + Following regulators of the RK808 PMIC block are supported. Note that the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO number as described in RK808 datasheet. diff --git a/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt b/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt index df664018c148..d759da606f75 100644 --- a/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt +++ b/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt @@ -57,7 +57,6 @@ audio-subsystem { clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; pinctrl-names = "default"; pinctrl-0 = <&i2s0_bus>; - status = "disabled"; }; serial_3: serial@11460000 { @@ -69,6 +68,5 @@ audio-subsystem { clock-names = "uart", "clk_uart_baud0"; pinctrl-names = "default"; pinctrl-0 = <&uart_aud_bus>; - status = "disabled"; }; }; diff --git a/Documentation/devicetree/bindings/mfd/stm32-lptimer.txt b/Documentation/devicetree/bindings/mfd/stm32-lptimer.txt new file mode 100644 index 000000000000..2a9ff29db9c9 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/stm32-lptimer.txt @@ -0,0 +1,48 @@ +STMicroelectronics STM32 Low-Power Timer + +The STM32 Low-Power Timer (LPTIM) is a 16-bit timer that provides several +functions: +- PWM output (with programmable prescaler, configurable polarity) +- Quadrature encoder, counter +- Trigger source for STM32 ADC/DAC (LPTIM_OUT) + +Required properties: +- compatible: Must be "st,stm32-lptimer". +- reg: Offset and length of the device's register set. +- clocks: Phandle to the clock used by the LP Timer module. +- clock-names: Must be "mux". +- #address-cells: Should be '<1>'. +- #size-cells: Should be '<0>'. + +Optional subnodes: +- pwm: See ../pwm/pwm-stm32-lp.txt +- counter: See ../iio/timer/stm32-lptimer-cnt.txt +- trigger: See ../iio/timer/stm32-lptimer-trigger.txt + +Example: + + timer@40002400 { + compatible = "st,stm32-lptimer"; + reg = <0x40002400 0x400>; + clocks = <&timer_clk>; + clock-names = "mux"; + #address-cells = <1>; + #size-cells = <0>; + + pwm { + compatible = "st,stm32-pwm-lp"; + pinctrl-names = "default"; + pinctrl-0 = <&lppwm1_pins>; + }; + + trigger@0 { + compatible = "st,stm32-lptimer-trigger"; + reg = <0>; + }; + + counter { + compatible = "st,stm32-lptimer-counter"; + pinctrl-names = "default"; + pinctrl-0 = <&lptim1_in_pins>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/tps6105x.txt b/Documentation/devicetree/bindings/mfd/tps6105x.txt new file mode 100644 index 000000000000..93602c7a19c8 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps6105x.txt @@ -0,0 +1,17 @@ +* Device tree bindings for TI TPS61050/61052 Boost Converters + +The TP61050/TPS61052 is a high-power "white LED driver". The +device provides LED, GPIO and regulator functionalities. + +Required properties: +- compatible: "ti,tps61050" or "ti,tps61052" +- reg: Specifies the I2C slave address + +Example: + +i2c0 { + tps61052@33 { + compatible = "ti,tps61052"; + reg = <0x33>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/zii,rave-sp.txt b/Documentation/devicetree/bindings/mfd/zii,rave-sp.txt new file mode 100644 index 000000000000..088eff9ddb78 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/zii,rave-sp.txt @@ -0,0 +1,39 @@ +Zodiac Inflight Innovations RAVE Supervisory Processor + +RAVE Supervisory Processor communicates with SoC over UART. It is +expected that its Device Tree node is specified as a child of a node +corresponding to UART controller used for communication. + +Required parent device properties: + + - compatible: Should be one of: + - "zii,rave-sp-niu" + - "zii,rave-sp-mezz" + - "zii,rave-sp-esb" + - "zii,rave-sp-rdu1" + - "zii,rave-sp-rdu2" + + - current-speed: Should be set to baud rate SP device is using + +RAVE SP consists of the following sub-devices: + +Device Description +------ ----------- +rave-sp-wdt : Watchdog +rave-sp-nvmem : Interface to onborad EEPROM +rave-sp-backlight : Display backlight +rave-sp-hwmon : Interface to onboard hardware sensors +rave-sp-leds : Interface to onboard LEDs +rave-sp-input : Interface to onboard power button + +Example of usage: + + rdu { + compatible = "zii,rave-sp-rdu2"; + current-speed = <1000000>; + + watchdog { + compatible = "zii,rave-sp-watchdog"; + }; + }; + |