diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd')
-rw-r--r-- | Documentation/devicetree/bindings/mfd/arizona.txt | 62 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/mfd/max8998.txt | 119 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/mfd/palmas.txt | 49 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/mfd/twl4030-power.txt | 28 |
4 files changed, 258 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt new file mode 100644 index 000000000000..0e295c9d8937 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -0,0 +1,62 @@ +Wolfson Arizona class audio SoCs + +These devices are audio SoCs with extensive digital capabilites and a range +of analogue I/O. + +Required properties: + + - compatible : one of the following chip-specific strings: + "wlf,wm5102" + "wlf,wm5110" + - reg : I2C slave address when connected using I2C, chip select number when + using SPI. + + - interrupts : The interrupt line the /IRQ signal for the device is + connected to. + - interrupt-controller : Arizona class devices contain interrupt controllers + and may provide interrupt services to other devices. + - interrupt-parent : The parent interrupt controller. + - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt + + - gpio-controller : Indicates this device is a GPIO controller. + - #gpio-cells : Must be 2. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + + - AVDD1-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply, + SPKVDDL-supply, SPKVDDR-supply : power supplies for the device, as covered + in Documentation/devicetree/bindings/regulator/regulator.txt + +Optional properties: + + - wlf,reset : GPIO specifier for the GPIO controlling /RESET + - wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA + + - wlf,gpio-defaults : A list of GPIO configuration register values. If + absent, no configuration of these registers is performed. If any + entry has a value that is out of range for a 16 bit register then + the chip default will be used. If present exactly five values must + be specified. + +Example: + +codec: wm5102@1a { + compatible = "wlf,wm5102"; + reg = <0x1a>; + interrupts = <347>; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + + gpio-controller; + #gpio-cells = <2>; + + wlf,gpio-defaults = < + 0x00000000, /* AIF1TXLRCLK */ + 0xffffffff, + 0xffffffff, + 0xffffffff, + 0xffffffff, + >; +}; diff --git a/Documentation/devicetree/bindings/mfd/max8998.txt b/Documentation/devicetree/bindings/mfd/max8998.txt new file mode 100644 index 000000000000..23a3650ff2a2 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max8998.txt @@ -0,0 +1,119 @@ +* Maxim MAX8998, National/TI LP3974 multi-function device + +The Maxim MAX8998 is a multi-function device which includes voltage/current +regulators, real time clock, battery charging controller and several +other sub-blocks. It is interfaced using an I2C interface. Each sub-block +is addressed by the host system using different i2c slave address. + +PMIC sub-block +-------------- + +The PMIC sub-block contains a number of voltage and current regulators, +with controllable parameters and dynamic voltage scaling capability. +In addition, it includes a real time clock and battery charging controller +as well. It is accessible at I2C address 0x66. + +Required properties: +- compatible: Should be one of the following: + - "maxim,max8998" for Maxim MAX8998 + - "national,lp3974" or "ti,lp3974" for National/TI LP3974. +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from MAX8998 are routed to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for main interrupt. + - Second interrupt specifier is for power-on/-off interrupt. +- max8998,pmic-buck1-dvs-gpios: GPIO specifiers for two host gpios used + for buck 1 dvs. The format of the gpio specifier depends on the gpio + controller. +- max8998,pmic-buck2-dvs-gpio: GPIO specifier for host gpio used + for buck 2 dvs. The format of the gpio specifier depends on the gpio + controller. +- max8998,pmic-buck1-default-dvs-idx: Default voltage setting selected from + the possible 4 options selectable by the dvs gpios. The value of this + property should be 0, 1, 2 or 3. If not specified or out of range, + a default value of 0 is taken. +- max8998,pmic-buck2-default-dvs-idx: Default voltage setting selected from + the possible 2 options selectable by the dvs gpios. The value of this + property should be 0 or 1. If not specified or out of range, a default + value of 0 is taken. +- max8998,pmic-buck-voltage-lock: If present, disallows changing of + preprogrammed buck dvfs voltages. + +Additional properties required if max8998,pmic-buck1-dvs-gpios is defined: +- max8998,pmic-buck1-dvs-voltage: An array of 4 voltage values in microvolts + for buck1 regulator that can be selected using dvs gpio. + +Additional properties required if max8998,pmic-buck2-dvs-gpio is defined: +- max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts + for buck2 regulator that can be selected using dvs gpio. + +Regulators: All the regulators of MAX8998 to be instantiated shall be +listed in a child node named 'regulators'. Each regulator is represented +by a child node of the 'regulators' node. + + regulator-name { + /* standard regulator bindings here */ + }; + +Following regulators of the MAX8998 PMIC block are supported. Note that +the 'n' in regulator name, as in LDOn or BUCKn, represents the LDO or BUCK +number as described in MAX8998 datasheet. + + - LDOn + - valid values for n are 2 to 17 + - Example: LDO2, LDO10, LDO17 + - BUCKn + - valid values for n are 1 to 4. + - Example: BUCK1, BUCK2, BUCK3, BUCK4 + + - ENVICHG: Battery Charging Current Monitor Output. This is a fixed + voltage type regulator + + - ESAFEOUT1: (ldo19) + - ESAFEOUT2: (ld020) + +Standard regulator bindings are used inside regulator subnodes. Check + Documentation/devicetree/bindings/regulator/regulator.txt +for more details. + +Example: + + pmic@66 { + compatible = "maxim,max8998-pmic"; + reg = <0x66>; + interrupt-parent = <&wakeup_eint>; + interrupts = <4 0>, <3 0>; + + /* Buck 1 DVS settings */ + max8998,pmic-buck1-default-dvs-idx = <0>; + max8998,pmic-buck1-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */ + <&gpx0 1 1 0 0>; /* SET2 */ + max8998,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1000000>, <950000>; + + /* Buck 2 DVS settings */ + max8998,pmic-buck2-default-dvs-idx = <0>; + max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */ + max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>; + + /* Regulators to instantiate */ + regulators { + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_ARM_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/palmas.txt b/Documentation/devicetree/bindings/mfd/palmas.txt new file mode 100644 index 000000000000..892537d1a48f --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/palmas.txt @@ -0,0 +1,49 @@ +* palmas device tree bindings + +The TI palmas family current members :- +twl6035 (palmas) +twl6037 (palmas) +tps65913 (palmas) +tps65914 (palmas) + +Required properties: +- compatible : Should be from the list + ti,twl6035 + ti,twl6036 + ti,twl6037 + ti,tps65913 + ti,tps65914 + ti,tps80036 +and also the generic series names + ti,palmas +- interrupt-controller : palmas has its own internal IRQs +- #interrupt-cells : should be set to 2 for IRQ number and flags + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt +- interrupt-parent : The parent interrupt controller. + +Optional properties: + ti,mux-padX : set the pad register X (1-2) to the correct muxing for the + hardware, if not set will use muxing in OTP. + +Example: + +palmas { + compatible = "ti,twl6035", "ti,palmas"; + reg = <0x48> + interrupt-parent = <&intc>; + interrupt-controller; + #interrupt-cells = <2>; + + ti,mux-pad1 = <0>; + ti,mux-pad2 = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + pmic { + compatible = "ti,twl6035-pmic", "ti,palmas-pmic"; + .... + }; +} diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt new file mode 100644 index 000000000000..8e15ec35ac99 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt @@ -0,0 +1,28 @@ +Texas Instruments TWL family (twl4030) reset and power management module + +The power management module inside the TWL family provides several facilities +to control the power resources, including power scripts. For now, the +binding only supports the complete shutdown of the system after poweroff. + +Required properties: +- compatible : must be "ti,twl4030-power" + +Optional properties: +- ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or + SLEEP-to-OFF transition when the system poweroffs. + +Example: +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_power: power { + compatible = "ti,twl4030-power"; + ti,use_poweroff; + }; + }; +}; |