diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mtd')
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/gpmc-nor.txt | 98 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/gpmc-onenand.txt | 3 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/gpmi-nand.txt | 17 |
3 files changed, 111 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nor.txt b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt new file mode 100644 index 000000000000..420b3ab18890 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt @@ -0,0 +1,98 @@ +Device tree bindings for NOR flash connect to TI GPMC + +NOR flash connected to the TI GPMC (found on OMAP boards) are represented as +child nodes of the GPMC controller with a name of "nor". + +All timing relevant properties as well as generic GPMC child properties are +explained in a separate documents. Please refer to +Documentation/devicetree/bindings/bus/ti-gpmc.txt + +Required properties: +- bank-width: Width of NOR flash in bytes. GPMC supports 8-bit and + 16-bit devices and so must be either 1 or 2 bytes. +- compatible: Documentation/devicetree/bindings/mtd/mtd-physmap.txt +- gpmc,cs-on-ns: Chip-select assertion time +- gpmc,cs-rd-off-ns: Chip-select de-assertion time for reads +- gpmc,cs-wr-off-ns: Chip-select de-assertion time for writes +- gpmc,oe-on-ns: Output-enable assertion time +- gpmc,oe-off-ns: Output-enable de-assertion time +- gpmc,we-on-ns Write-enable assertion time +- gpmc,we-off-ns: Write-enable de-assertion time +- gpmc,access-ns: Start cycle to first data capture (read access) +- gpmc,rd-cycle-ns: Total read cycle time +- gpmc,wr-cycle-ns: Total write cycle time +- linux,mtd-name: Documentation/devicetree/bindings/mtd/mtd-physmap.txt +- reg: Chip-select, base address (relative to chip-select) + and size of NOR flash. Note that base address will be + typically 0 as this is the start of the chip-select. + +Optional properties: +- gpmc,XXX Additional GPMC timings and settings parameters. See + Documentation/devicetree/bindings/bus/ti-gpmc.txt + +Optional properties for partiton table parsing: +- #address-cells: should be set to 1 +- #size-cells: should be set to 1 + +Example: + +gpmc: gpmc@6e000000 { + compatible = "ti,omap3430-gpmc", "simple-bus"; + ti,hwmods = "gpmc"; + reg = <0x6e000000 0x1000>; + interrupts = <20>; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <4>; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <0 0 0x10000000 0x08000000>; + + nor@0,0 { + compatible = "cfi-flash"; + linux,mtd-name= "intel,pf48f6000m0y1be"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0 0 0x08000000>; + bank-width = <2>; + + gpmc,mux-add-data; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <186>; + gpmc,cs-wr-off-ns = <186>; + gpmc,adv-on-ns = <12>; + gpmc,adv-rd-off-ns = <48>; + gpmc,adv-wr-off-ns = <48>; + gpmc,oe-on-ns = <54>; + gpmc,oe-off-ns = <168>; + gpmc,we-on-ns = <54>; + gpmc,we-off-ns = <168>; + gpmc,rd-cycle-ns = <186>; + gpmc,wr-cycle-ns = <186>; + gpmc,access-ns = <114>; + gpmc,page-burst-access-ns = <6>; + gpmc,bus-turnaround-ns = <12>; + gpmc,cycle2cycle-delay-ns = <18>; + gpmc,wr-data-mux-bus-ns = <90>; + gpmc,wr-access-ns = <186>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-diffcsen; + + partition@0 { + label = "bootloader-nor"; + reg = <0 0x40000>; + }; + partition@0x40000 { + label = "params-nor"; + reg = <0x40000 0x40000>; + }; + partition@0x80000 { + label = "kernel-nor"; + reg = <0x80000 0x200000>; + }; + partition@0x280000 { + label = "filesystem-nor"; + reg = <0x240000 0x7d80000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt index deec9da224a2..b7529424ac88 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt @@ -10,6 +10,8 @@ Documentation/devicetree/bindings/bus/ti-gpmc.txt Required properties: - reg: The CS line the peripheral is connected to + - gpmc,device-width Width of the ONENAND device connected to the GPMC + in bytes. Must be 1 or 2. Optional properties: @@ -34,6 +36,7 @@ Example for an OMAP3430 board: onenand@0 { reg = <0 0 0>; /* CS0, offset 0 */ + gpmc,device-width = <2>; #address-cells = <1>; #size-cells = <1>; diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt index 3fb3f9015365..551b2a179d01 100644 --- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt @@ -7,10 +7,12 @@ Required properties: - compatible : should be "fsl,<chip>-gpmi-nand" - reg : should contain registers location and length for gpmi and bch. - reg-names: Should contain the reg names "gpmi-nand" and "bch" - - interrupts : The first is the DMA interrupt number for GPMI. - The second is the BCH interrupt number. - - interrupt-names : The interrupt names "gpmi-dma", "bch"; - - fsl,gpmi-dma-channel : Should contain the dma channel it uses. + - interrupts : BCH interrupt number. + - interrupt-names : Should be "bch". + - dmas: DMA specifier, consisting of a phandle to DMA controller node + and GPMI DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. + - dma-names: Must be "rx-tx". Optional properties: - nand-on-flash-bbt: boolean to enable on flash bbt option if not @@ -27,9 +29,10 @@ gpmi-nand@8000c000 { #size-cells = <1>; reg = <0x8000c000 2000>, <0x8000a000 2000>; reg-names = "gpmi-nand", "bch"; - interrupts = <88>, <41>; - interrupt-names = "gpmi-dma", "bch"; - fsl,gpmi-dma-channel = <4>; + interrupts = <41>; + interrupt-names = "bch"; + dmas = <&dma_apbh 4>; + dma-names = "rx-tx"; partition@0 { ... |