summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml')
-rw-r--r--Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml118
1 files changed, 118 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
new file mode 100644
index 000000000000..fbdc2083bec4
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
@@ -0,0 +1,118 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/broadcom-bluetooth.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom Bluetooth Chips
+
+maintainers:
+ - Linus Walleij <linus.walleij@linaro.org>
+
+description:
+ This binding describes Broadcom UART-attached bluetooth chips.
+
+properties:
+ compatible:
+ enum:
+ - brcm,bcm20702a1
+ - brcm,bcm4329-bt
+ - brcm,bcm4330-bt
+ - brcm,bcm4334-bt
+ - brcm,bcm43438-bt
+ - brcm,bcm4345c5
+ - brcm,bcm43540-bt
+ - brcm,bcm4335a0
+
+ shutdown-gpios:
+ maxItems: 1
+ description: GPIO specifier for the line BT_REG_ON used to
+ power on the BT module
+
+ reset-gpios:
+ maxItems: 1
+ description: GPIO specifier for the line BT_RST_N used to
+ reset the BT module. This should be marked as
+ GPIO_ACTIVE_LOW.
+
+ device-wakeup-gpios:
+ maxItems: 1
+ description: GPIO specifier for the line BT_WAKE used to
+ wakeup the controller. This is using the BT_GPIO_0
+ pin on the chip when in use.
+
+ host-wakeup-gpios:
+ maxItems: 1
+ deprecated: true
+ description: GPIO specifier for the line HOST_WAKE used
+ to wakeup the host processor. This is using he BT_GPIO_1
+ pin on the chip when in use. This is deprecated and replaced
+ by interrupts and "host-wakeup" interrupt-names
+
+ clocks:
+ maxItems: 2
+ description: 1 or 2 clocks as defined in clock-names below,
+ in that order
+
+ clock-names:
+ description: Names of the 1 to 2 supplied clocks
+ items:
+ - const: txco
+ - const: lpo
+ - const: extclk
+
+ vbat-supply:
+ description: phandle to regulator supply for VBAT
+
+ vddio-supply:
+ description: phandle to regulator supply for VDDIO
+
+ brcm,bt-pcm-int-params:
+ $ref: /schemas/types.yaml#/definitions/uint8-array
+ minItems: 5
+ maxItems: 5
+ description: |-
+ configure PCM parameters via a 5-byte array:
+ sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S
+ pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps
+ pcm-frame-type: short, long
+ pcm-sync-mode: slave, master
+ pcm-clock-mode: slave, master
+
+ interrupts:
+ items:
+ - description: Handle to the line HOST_WAKE used to wake
+ up the host processor. This uses the BT_GPIO_1 pin on
+ the chip when in use.
+
+ interrupt-names:
+ items:
+ - const: host-wakeup
+
+ max-speed: true
+ current-speed: true
+
+required:
+ - compatible
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ uart {
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm4330-bt";
+ max-speed = <921600>;
+ brcm,bt-pcm-int-params = [01 02 00 01 01];
+ shutdown-gpios = <&gpio 30 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio>;
+ interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+ };
+ };