diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
23 files changed, 1049 insertions, 190 deletions
diff --git a/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml b/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml index ae91aa9d8616..64c20c92c07d 100644 --- a/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml +++ b/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml @@ -40,18 +40,22 @@ allOf: then: properties: clocks: + minItems: 3 + maxItems: 4 items: - description: GMAC main clock - description: First parent clock of the internal mux - description: Second parent clock of the internal mux + - description: The clock which drives the timing adjustment logic clock-names: minItems: 3 - maxItems: 3 + maxItems: 4 items: - const: stmmaceth - const: clkin0 - const: clkin1 + - const: timing-adjustment amlogic,tx-delay-ns: $ref: /schemas/types.yaml#definitions/uint32 @@ -67,6 +71,19 @@ allOf: PHY and MAC are adding a delay). Any configuration is ignored when the phy-mode is set to "rmii". + amlogic,rx-delay-ns: + enum: + - 0 + - 2 + default: 0 + description: + The internal RGMII RX clock delay (provided by this IP block) in + nanoseconds. When phy-mode is set to "rgmii" then the RX delay + should be explicitly configured. When the phy-mode is set to + either "rgmii-id" or "rgmii-rxid" the RX clock delay is already + provided by the PHY. Any configuration is ignored when the + phy-mode is set to "rmii". + properties: compatible: additionalItems: true @@ -107,7 +124,7 @@ examples: reg = <0xc9410000 0x10000>, <0xc8834540 0x8>; interrupts = <8>; interrupt-names = "macirq"; - clocks = <&clk_eth>, <&clkc_fclk_div2>, <&clk_mpll2>; - clock-names = "stmmaceth", "clkin0", "clkin1"; + clocks = <&clk_eth>, <&clk_fclk_div2>, <&clk_mpll2>, <&clk_fclk_div2>; + clock-names = "stmmaceth", "clkin0", "clkin1", "timing-adjustment"; phy-mode = "rgmii"; }; diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index 5201bc15fdd6..cfd1afdc6e94 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -110,6 +110,9 @@ Ethernet switch connected via MDIO to the host, CPU port wired to eth0: #size-cells = <0>; ports { + #address-cells = <1>; + #size-cells = <0>; + port0@0 { reg = <0>; label = "lan1"; diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml index 5aa141ccc113..9b1f1147ca36 100644 --- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml +++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml @@ -81,7 +81,8 @@ properties: $ref: /schemas/types.yaml#definitions/flag description: If set, indicates the PHY device does not correctly release - the turn around line low at the end of a MDIO transaction. + the turn around line low at end of the control phase of the + MDIO transaction. enet-phy-lane-swap: $ref: /schemas/types.yaml#definitions/flag diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index ff8b0f211aa1..9b543789cd52 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -22,8 +22,11 @@ Optional properties: - fsl,err006687-workaround-present: If present indicates that the system has the hardware workaround for ERR006687 applied and does not need a software workaround. -- gpr: phandle of SoC general purpose register mode. Required for wake on LAN - on some SoCs +- fsl,stop-mode: register bits of stop mode control, the format is + <&gpr req_gpr req_bit>. + gpr is the phandle to general purpose register node. + req_gpr is the gpr register offset for ENET stop request. + req_bit is the gpr bit offset for ENET stop request. -interrupt-names: names of the interrupts listed in interrupts property in the same order. The defaults if not specified are __Number of interrupts__ __Default__ @@ -82,6 +85,7 @@ ethernet@83fec000 { phy-supply = <®_fec_supply>; phy-handle = <ðphy>; mdio { + clock-frequency = <5000000>; ethphy: ethernet-phy@6 { compatible = "ethernet-phy-ieee802.3-c22"; reg = <6>; diff --git a/Documentation/devicetree/bindings/net/imx-dwmac.txt b/Documentation/devicetree/bindings/net/imx-dwmac.txt new file mode 100644 index 000000000000..921d522fe8d7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/imx-dwmac.txt @@ -0,0 +1,56 @@ +IMX8 glue layer controller, NXP imx8 families support Synopsys MAC 5.10a IP. + +This file documents platform glue layer for IMX. +Please see stmmac.txt for the other unchanged properties. + +The device node has following properties. + +Required properties: +- compatible: Should be "nxp,imx8mp-dwmac-eqos" to select glue layer + and "snps,dwmac-5.10a" to select IP version. +- clocks: Must contain a phandle for each entry in clock-names. +- clock-names: Should be "stmmaceth" for the host clock. + Should be "pclk" for the MAC apb clock. + Should be "ptp_ref" for the MAC timer clock. + Should be "tx" for the MAC RGMII TX clock: + Should be "mem" for EQOS MEM clock. + - "mem" clock is required for imx8dxl platform. + - "mem" clock is not required for imx8mp platform. +- interrupt-names: Should contain a list of interrupt names corresponding to + the interrupts in the interrupts property, if available. + Should be "macirq" for the main MAC IRQ + Should be "eth_wake_irq" for the IT which wake up system +- intf_mode: Should be phandle/offset pair. The phandle to the syscon node which + encompases the GPR register, and the offset of the GPR register. + - required for imx8mp platform. + - is optional for imx8dxl platform. + +Optional properties: +- intf_mode: is optional for imx8dxl platform. +- snps,rmii_refclk_ext: to select RMII reference clock from external. + +Example: + eqos: ethernet@30bf0000 { + compatible = "nxp,imx8mp-dwmac-eqos", "snps,dwmac-5.10a"; + reg = <0x30bf0000 0x10000>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "eth_wake_irq", "macirq"; + clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, + <&clk IMX8MP_CLK_QOS_ENET_ROOT>, + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, + <&clk IMX8MP_CLK_ENET_QOS>; + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; + assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>, + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, + <&clk IMX8MP_CLK_ENET_QOS>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, + <&clk IMX8MP_SYS_PLL2_100M>, + <&clk IMX8MP_SYS_PLL2_125M>; + assigned-clock-rates = <0>, <100000000>, <125000000>; + nvmem-cells = <ð_mac0>; + nvmem-cell-names = "mac-address"; + nvmem_macaddr_swap; + intf_mode = <&gpr 0x4>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/net/mdio.yaml b/Documentation/devicetree/bindings/net/mdio.yaml index 50c3397a82bc..d6a3bf8550eb 100644 --- a/Documentation/devicetree/bindings/net/mdio.yaml +++ b/Documentation/devicetree/bindings/net/mdio.yaml @@ -31,13 +31,25 @@ properties: maxItems: 1 description: The phandle and specifier for the GPIO that controls the RESET - lines of all PHYs on that MDIO bus. + lines of all devices on that MDIO bus. reset-delay-us: description: - RESET pulse width in microseconds. It applies to all PHY devices - and must therefore be appropriately determined based on all PHY - requirements (maximum value of all per-PHY RESET pulse widths). + RESET pulse width in microseconds. It applies to all MDIO devices + and must therefore be appropriately determined based on all devices + requirements (maximum value of all per-device RESET pulse widths). + + clock-frequency: + description: + Desired MDIO bus clock frequency in Hz. Values greater than IEEE 802.3 + defined 2.5MHz should only be used when all devices on the bus support + the given clock speed. + + suppress-preamble: + description: + The 32 bit preamble should be suppressed. In order for this to + work, all devices on the bus must support suppressed preamble. + type: boolean patternProperties: "^ethernet-phy@[0-9a-f]+$": @@ -48,7 +60,35 @@ patternProperties: minimum: 0 maximum: 31 description: - The ID number for the PHY. + The ID number for the device. + + broken-turn-around: + $ref: /schemas/types.yaml#definitions/flag + description: + If set, indicates the MDIO device does not correctly release + the turn around line low at end of the control phase of the + MDIO transaction. + + resets: + maxItems: 1 + + reset-names: + const: phy + + reset-gpios: + maxItems: 1 + description: + The GPIO phandle and specifier for the MDIO reset signal. + + reset-assert-us: + description: + Delay after the reset was asserted in microseconds. If this + property is missing the delay will be skipped. + + reset-deassert-us: + description: + Delay after the reset was deasserted in microseconds. If + this property is missing the delay will be skipped. required: - reg diff --git a/Documentation/devicetree/bindings/net/mediatek,star-emac.yaml b/Documentation/devicetree/bindings/net/mediatek,star-emac.yaml new file mode 100644 index 000000000000..aea88e621792 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mediatek,star-emac.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/mediatek,star-emac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek STAR Ethernet MAC Controller + +maintainers: + - Bartosz Golaszewski <bgolaszewski@baylibre.com> + +description: + This Ethernet MAC is used on the MT8* family of SoCs from MediaTek. + It's compliant with 802.3 standards and supports half- and full-duplex + modes with flow-control as well as CRC offloading and VLAN tags. + +allOf: + - $ref: "ethernet-controller.yaml#" + +properties: + compatible: + enum: + - mediatek,mt8516-eth + - mediatek,mt8518-eth + - mediatek,mt8175-eth + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 3 + maxItems: 3 + + clock-names: + additionalItems: false + items: + - const: core + - const: reg + - const: trans + + mediatek,pericfg: + $ref: /schemas/types.yaml#definitions/phandle + description: + Phandle to the device containing the PERICFG register range. This is used + to control the MII mode. + + mdio: + type: object + description: + Creates and registers an MDIO bus. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - mediatek,pericfg + - phy-handle + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/mt8516-clk.h> + + ethernet: ethernet@11180000 { + compatible = "mediatek,mt8516-eth"; + reg = <0x11180000 0x1000>; + mediatek,pericfg = <&pericfg>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_RG_ETH>, + <&topckgen CLK_TOP_66M_ETH>, + <&topckgen CLK_TOP_133M_ETH>; + clock-names = "core", "reg", "trans"; + phy-handle = <ð_phy>; + phy-mode = "rmii"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + eth_phy: ethernet-phy@0 { + reg = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/nxp,tja11xx.yaml b/Documentation/devicetree/bindings/net/nxp,tja11xx.yaml new file mode 100644 index 000000000000..42be0255512b --- /dev/null +++ b/Documentation/devicetree/bindings/net/nxp,tja11xx.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: GPL-2.0+ +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/nxp,tja11xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP TJA11xx PHY + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + - Florian Fainelli <f.fainelli@gmail.com> + - Heiner Kallweit <hkallweit1@gmail.com> + +description: + Bindings for NXP TJA11xx automotive PHYs + +allOf: + - $ref: ethernet-phy.yaml# + +patternProperties: + "^ethernet-phy@[0-9a-f]+$": + type: object + description: | + Some packages have multiple PHYs. Secondary PHY should be defines as + subnode of the first (parent) PHY. + + properties: + reg: + minimum: 0 + maximum: 31 + description: + The ID number for the child PHY. Should be +1 of parent PHY. + + required: + - reg + +examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + tja1101_phy0: ethernet-phy@4 { + reg = <0x4>; + }; + }; + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + tja1102_phy0: ethernet-phy@4 { + reg = <0x4>; + #address-cells = <1>; + #size-cells = <0>; + + tja1102_phy1: ethernet-phy@5 { + reg = <0x5>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/qca,ar71xx.txt b/Documentation/devicetree/bindings/net/qca,ar71xx.txt deleted file mode 100644 index 2a33e71ba72b..000000000000 --- a/Documentation/devicetree/bindings/net/qca,ar71xx.txt +++ /dev/null @@ -1,45 +0,0 @@ -Required properties: -- compatible: Should be "qca,<soc>-eth". Currently support compatibles are: - qca,ar7100-eth - Atheros AR7100 - qca,ar7240-eth - Atheros AR7240 - qca,ar7241-eth - Atheros AR7241 - qca,ar7242-eth - Atheros AR7242 - qca,ar9130-eth - Atheros AR9130 - qca,ar9330-eth - Atheros AR9330 - qca,ar9340-eth - Atheros AR9340 - qca,qca9530-eth - Qualcomm Atheros QCA9530 - qca,qca9550-eth - Qualcomm Atheros QCA9550 - qca,qca9560-eth - Qualcomm Atheros QCA9560 - -- reg : Address and length of the register set for the device -- interrupts : Should contain eth interrupt -- phy-mode : See ethernet.txt file in the same directory -- clocks: the clock used by the core -- clock-names: the names of the clock listed in the clocks property. These are - "eth" and "mdio". -- resets: Should contain phandles to the reset signals -- reset-names: Should contain the names of reset signal listed in the resets - property. These are "mac" and "mdio" - -Optional properties: -- phy-handle : phandle to the PHY device connected to this device. -- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. - Use instead of phy-handle. - -Optional subnodes: -- mdio : specifies the mdio bus, used as a container for phy nodes - according to phy.txt in the same directory - -Example: - -ethernet@1a000000 { - compatible = "qca,ar9330-eth"; - reg = <0x1a000000 0x200>; - interrupts = <5>; - resets = <&rst 13>, <&rst 23>; - reset-names = "mac", "mdio"; - clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_MDIO>; - clock-names = "eth", "mdio"; - - phy-mode = "gmii"; -}; diff --git a/Documentation/devicetree/bindings/net/qca,ar71xx.yaml b/Documentation/devicetree/bindings/net/qca,ar71xx.yaml new file mode 100644 index 000000000000..f99a5aabe923 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca,ar71xx.yaml @@ -0,0 +1,216 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qca,ar71xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: QCA AR71XX MAC + +allOf: + - $ref: ethernet-controller.yaml# + +maintainers: + - Oleksij Rempel <o.rempel@pengutronix.de> + +properties: + compatible: + oneOf: + - items: + - enum: + - qca,ar7100-eth # Atheros AR7100 + - qca,ar7240-eth # Atheros AR7240 + - qca,ar7241-eth # Atheros AR7241 + - qca,ar7242-eth # Atheros AR7242 + - qca,ar9130-eth # Atheros AR9130 + - qca,ar9330-eth # Atheros AR9330 + - qca,ar9340-eth # Atheros AR9340 + - qca,qca9530-eth # Qualcomm Atheros QCA9530 + - qca,qca9550-eth # Qualcomm Atheros QCA9550 + - qca,qca9560-eth # Qualcomm Atheros QCA9560 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + '#address-cells': + description: number of address cells for the MDIO bus + const: 1 + + '#size-cells': + description: number of size cells on the MDIO bus + const: 0 + + clocks: + items: + - description: MAC main clock + - description: MDIO clock + + clock-names: + items: + - const: eth + - const: mdio + + resets: + items: + - description: MAC reset + - description: MDIO reset + + reset-names: + items: + - const: mac + - const: mdio + +required: + - compatible + - reg + - interrupts + - phy-mode + - clocks + - clock-names + - resets + - reset-names + +examples: + # Lager board + - | + eth0: ethernet@19000000 { + compatible = "qca,ar9330-eth"; + reg = <0x19000000 0x200>; + interrupts = <4>; + resets = <&rst 9>, <&rst 22>; + reset-names = "mac", "mdio"; + clocks = <&pll 1>, <&pll 2>; + clock-names = "eth", "mdio"; + qca,ethcfg = <ðcfg>; + phy-mode = "mii"; + phy-handle = <&phy_port4>; + }; + + eth1: ethernet@1a000000 { + compatible = "qca,ar9330-eth"; + reg = <0x1a000000 0x200>; + interrupts = <5>; + resets = <&rst 13>, <&rst 23>; + reset-names = "mac", "mdio"; + clocks = <&pll 1>, <&pll 2>; + clock-names = "eth", "mdio"; + + phy-mode = "gmii"; + + status = "disabled"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch10: switch@10 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "qca,ar9331-switch"; + reg = <0x10>; + resets = <&rst 8>; + reset-names = "switch"; + + interrupt-parent = <&miscintc>; + interrupts = <12>; + + interrupt-controller; + #interrupt-cells = <1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + switch_port0: port@0 { + reg = <0x0>; + label = "cpu"; + ethernet = <ð1>; + + phy-mode = "gmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + switch_port1: port@1 { + reg = <0x1>; + phy-handle = <&phy_port0>; + phy-mode = "internal"; + + status = "disabled"; + }; + + switch_port2: port@2 { + reg = <0x2>; + phy-handle = <&phy_port1>; + phy-mode = "internal"; + + status = "disabled"; + }; + + switch_port3: port@3 { + reg = <0x3>; + phy-handle = <&phy_port2>; + phy-mode = "internal"; + + status = "disabled"; + }; + + switch_port4: port@4 { + reg = <0x4>; + phy-handle = <&phy_port3>; + phy-mode = "internal"; + + status = "disabled"; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&switch10>; + + phy_port0: phy@0 { + reg = <0x0>; + interrupts = <0>; + status = "disabled"; + }; + + phy_port1: phy@1 { + reg = <0x1>; + interrupts = <0>; + status = "disabled"; + }; + + phy_port2: phy@2 { + reg = <0x2>; + interrupts = <0>; + status = "disabled"; + }; + + phy_port3: phy@3 { + reg = <0x3>; + interrupts = <0>; + status = "disabled"; + }; + + phy_port4: phy@4 { + reg = <0x4>; + interrupts = <0>; + status = "disabled"; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/qcom,ipa.yaml b/Documentation/devicetree/bindings/net/qcom,ipa.yaml index 140f15245654..7b749fc04c32 100644 --- a/Documentation/devicetree/bindings/net/qcom,ipa.yaml +++ b/Documentation/devicetree/bindings/net/qcom,ipa.yaml @@ -20,7 +20,10 @@ description: The GSI is an integral part of the IPA, but it is logically isolated and has a distinct interrupt and a separately-defined address space. - See also soc/qcom/qcom,smp2p.txt and interconnect/interconnect.txt. + See also soc/qcom/qcom,smp2p.txt and interconnect/interconnect.txt. See + iommu/iommu.txt and iommu/arm,smmu.yaml for more information about SMMU + bindings. + - | -------- --------- @@ -54,6 +57,9 @@ properties: - const: ipa-shared - const: gsi + iommus: + maxItems: 1 + clocks: maxItems: 1 @@ -126,6 +132,7 @@ properties: required: - compatible + - iommus - reg - clocks - interrupts @@ -164,6 +171,7 @@ examples: modem-init; modem-remoteproc = <&mss_pil>; + iommus = <&apps_smmu 0x720 0x3>; reg = <0 0x1e40000 0 0x7000>, <0 0x1e47000 0 0x2000>, <0 0x1e04000 0 0x2c000>; diff --git a/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml new file mode 100644 index 000000000000..13555a89975f --- /dev/null +++ b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qcom,ipq4019-mdio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm IPQ40xx MDIO Controller Device Tree Bindings + +maintainers: + - Robert Marko <robert.marko@sartura.hr> + +allOf: + - $ref: "mdio.yaml#" + +properties: + compatible: + const: qcom,ipq4019-mdio + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + reg: + maxItems: 1 + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + +examples: + - | + mdio@90000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "qcom,ipq4019-mdio"; + reg = <0x90000 0x64>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; + + ethphy1: ethernet-phy@1 { + reg = <1>; + }; + + ethphy2: ethernet-phy@2 { + reg = <2>; + }; + + ethphy3: ethernet-phy@3 { + reg = <3>; + }; + + ethphy4: ethernet-phy@4 { + reg = <4>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt index d2202791c1d4..709ca6d51650 100644 --- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt +++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt @@ -10,9 +10,11 @@ device the slave device is attached to. Required properties: - compatible: should contain one of the following: * "qcom,qca6174-bt" + * "qcom,qca9377-bt" * "qcom,wcn3990-bt" * "qcom,wcn3991-bt" * "qcom,wcn3998-bt" + * "qcom,qca6390-bt" Optional properties for compatible string qcom,qca6174-bt: @@ -20,6 +22,10 @@ Optional properties for compatible string qcom,qca6174-bt: - clocks: clock provided to the controller (SUSCLK_32KHZ) - firmware-name: specify the name of nvm firmware to load +Optional properties for compatible string qcom,qca9377-bt: + + - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml + Required properties for compatible string qcom,wcn399x-bt: - vddio-supply: VDD_IO supply regulator handle. diff --git a/Documentation/devicetree/bindings/net/realtek-bluetooth.yaml b/Documentation/devicetree/bindings/net/realtek-bluetooth.yaml new file mode 100644 index 000000000000..f15a5e5e4859 --- /dev/null +++ b/Documentation/devicetree/bindings/net/realtek-bluetooth.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/realtek-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RTL8723BS/RTL8723CS/RTL8822CS Bluetooth Device Tree Bindings + +maintainers: + - Vasily Khoruzhick <anarsoul@gmail.com> + - Alistair Francis <alistair@alistair23.me> + +description: + RTL8723CS/RTL8723CS/RTL8822CS is WiFi + BT chip. WiFi part is connected over + SDIO, while BT is connected over serial. It speaks H5 protocol with few + extra commands to upload firmware and change module speed. + +properties: + compatible: + oneOf: + - const: "realtek,rtl8723bs-bt" + - const: "realtek,rtl8723cs-bt" + - const: "realtek,rtl8822cs-bt" + + device-wake-gpios: + maxItems: 1 + description: GPIO specifier, used to wakeup the BT module + + enable-gpios: + maxItems: 1 + description: GPIO specifier, used to enable the BT module + + host-wake-gpios: + maxItems: 1 + description: GPIO specifier, used to wakeup the host processor + +required: + - compatible + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + uart-has-rtscts = <1>; + + bluetooth { + compatible = "realtek,rtl8723bs-bt"; + device-wake-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */ + host-wakeup-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + }; + }; diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt deleted file mode 100644 index 4e85fc495e87..000000000000 --- a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt +++ /dev/null @@ -1,64 +0,0 @@ -* Socionext AVE ethernet controller - -This describes the devicetree bindings for AVE ethernet controller -implemented on Socionext UniPhier SoCs. - -Required properties: - - compatible: Should be - - "socionext,uniphier-pro4-ave4" : for Pro4 SoC - - "socionext,uniphier-pxs2-ave4" : for PXs2 SoC - - "socionext,uniphier-ld11-ave4" : for LD11 SoC - - "socionext,uniphier-ld20-ave4" : for LD20 SoC - - "socionext,uniphier-pxs3-ave4" : for PXs3 SoC - - reg: Address where registers are mapped and size of region. - - interrupts: Should contain the MAC interrupt. - - phy-mode: See ethernet.txt in the same directory. Allow to choose - "rgmii", "rmii", "mii", or "internal" according to the PHY. - The acceptable mode is SoC-dependent. - - phy-handle: Should point to the external phy device. - See ethernet.txt file in the same directory. - - clocks: A phandle to the clock for the MAC. - For Pro4 SoC, that is "socionext,uniphier-pro4-ave4", - another MAC clock, GIO bus clock and PHY clock are also required. - - clock-names: Should contain - - "ether", "ether-gb", "gio", "ether-phy" for Pro4 SoC - - "ether" for others - - resets: A phandle to the reset control for the MAC. For Pro4 SoC, - GIO bus reset is also required. - - reset-names: Should contain - - "ether", "gio" for Pro4 SoC - - "ether" for others - - socionext,syscon-phy-mode: A phandle to syscon with one argument - that configures phy mode. The argument is the ID of MAC instance. - -The MAC address will be determined using the optional properties -defined in ethernet.txt. - -Required subnode: - - mdio: A container for child nodes representing phy nodes. - See phy.txt in the same directory. - -Example: - - ether: ethernet@65000000 { - compatible = "socionext,uniphier-ld20-ave4"; - reg = <0x65000000 0x8500>; - interrupts = <0 66 4>; - phy-mode = "rgmii"; - phy-handle = <ðphy>; - clock-names = "ether"; - clocks = <&sys_clk 6>; - reset-names = "ether"; - resets = <&sys_rst 6>; - socionext,syscon-phy-mode = <&soc_glue 0>; - local-mac-address = [00 00 00 00 00 00]; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - ethphy: ethphy@1 { - reg = <1>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.yaml b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.yaml new file mode 100644 index 000000000000..7d84a863b9b9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.yaml @@ -0,0 +1,111 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/socionext,uniphier-ave4.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Socionext AVE ethernet controller + +maintainers: + - Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +description: | + This describes the devicetree bindings for AVE ethernet controller + implemented on Socionext UniPhier SoCs. + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + enum: + - socionext,uniphier-pro4-ave4 + - socionext,uniphier-pxs2-ave4 + - socionext,uniphier-ld11-ave4 + - socionext,uniphier-ld20-ave4 + - socionext,uniphier-pxs3-ave4 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + phy-mode: true + + phy-handle: true + + mac-address: true + + local-mac-address: true + + clocks: + minItems: 1 + maxItems: 4 + + clock-names: + oneOf: + - items: # for Pro4 + - const: gio + - const: ether + - const: ether-gb + - const: ether-phy + - const: ether # for others + + resets: + minItems: 1 + maxItems: 2 + + reset-names: + oneOf: + - items: # for Pro4 + - const: gio + - const: ether + - const: ether # for others + + socionext,syscon-phy-mode: + $ref: /schemas/types.yaml#definitions/phandle-array + description: + A phandle to syscon with one argument that configures phy mode. + The argument is the ID of MAC instance. + + mdio: + $ref: mdio.yaml# + +required: + - compatible + - reg + - interrupts + - phy-mode + - phy-handle + - clocks + - clock-names + - resets + - reset-names + - mdio + +additionalProperties: false + +examples: + - | + ether: ethernet@65000000 { + compatible = "socionext,uniphier-ld20-ave4"; + reg = <0x65000000 0x8500>; + interrupts = <0 66 4>; + phy-mode = "rgmii"; + phy-handle = <ðphy>; + clock-names = "ether"; + clocks = <&sys_clk 6>; + reset-names = "ether"; + resets = <&sys_rst 6>; + socionext,syscon-phy-mode = <&soc_glue 0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethernet-phy@1 { + reg = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt deleted file mode 100644 index 44e2a4fab29e..000000000000 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ /dev/null @@ -1,68 +0,0 @@ -* Texas Instruments - dp83867 Giga bit ethernet phy - -Required properties: - - reg - The ID number for the phy, usually a small integer - - ti,rx-internal-delay - RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h - for applicable values. Required only if interface type is - PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_RXID - - ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h - for applicable values. Required only if interface type is - PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID - -Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock delays - will be left at their default values, as set by the PHY's pin strapping. - The default strapping will use a delay of 2.00 ns. Thus - PHY_INTERFACE_MODE_RGMII, by default, does not behave as RGMII with no - internal delay, but as PHY_INTERFACE_MODE_RGMII_ID. The device tree - should use "rgmii-id" if internal delays are desired as this may be - changed in future to cause "rgmii" mode to disable delays. - -Optional property: - - ti,min-output-impedance - MAC Interface Impedance control to set - the programmable output impedance to - minimum value (35 ohms). - - ti,max-output-impedance - MAC Interface Impedance control to set - the programmable output impedance to - maximum value (70 ohms). - - ti,dp83867-rxctrl-strap-quirk - This denotes the fact that the - board has RX_DV/RX_CTRL pin strapped in - mode 1 or 2. To ensure PHY operation, - there are specific actions that - software needs to take when this pin is - strapped in these modes. See data manual - for details. - - ti,clk-output-sel - Muxing option for CLK_OUT pin. See dt-bindings/net/ti-dp83867.h - for applicable values. The CLK_OUT pin can also - be disabled by this property. When omitted, the - PHY's default will be left as is. - - ti,sgmii-ref-clock-output-enable - This denotes which - SGMII configuration is used (4 or 6-wire modes). - Some MACs work with differential SGMII clock. - See data manual for details. - - - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h - for applicable values (deprecated) - - -tx-fifo-depth - As defined in the ethernet-controller.yaml. Values for - the depth can be found in dt-bindings/net/ti-dp83867.h - -rx-fifo-depth - As defined in the ethernet-controller.yaml. Values for - the depth can be found in dt-bindings/net/ti-dp83867.h - -Note: ti,min-output-impedance and ti,max-output-impedance are mutually - exclusive. When both properties are present ti,max-output-impedance - takes precedence. - -Default child nodes are standard Ethernet PHY device -nodes as described in Documentation/devicetree/bindings/net/phy.txt - -Example: - - ethernet-phy@0 { - reg = <0>; - ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; - ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; - tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; - }; - -Datasheet can be found: -http://www.ti.com/product/DP83867IR/datasheet diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.yaml b/Documentation/devicetree/bindings/net/ti,dp83867.yaml new file mode 100644 index 000000000000..554dcd7a40a9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,dp83867.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) +# Copyright (C) 2019 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/net/ti,dp83867.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI DP83867 ethernet PHY + +allOf: + - $ref: "ethernet-controller.yaml#" + +maintainers: + - Dan Murphy <dmurphy@ti.com> + +description: | + The DP83867 device is a robust, low power, fully featured Physical Layer + transceiver with integrated PMD sublayers to support 10BASE-Te, 100BASE-TX + and 1000BASE-T Ethernet protocols. + + The DP83867 is designed for easy implementation of 10/100/1000 Mbps Ethernet + LANs. It interfaces directly to twisted pair media via an external + transformer. This device interfaces directly to the MAC layer through the + IEEE 802.3 Standard Media Independent Interface (MII), the IEEE 802.3 Gigabit + Media Independent Interface (GMII) or Reduced GMII (RGMII). + + Specifications about the charger can be found at: + https://www.ti.com/lit/gpn/dp83867ir + +properties: + reg: + maxItems: 1 + + ti,min-output-impedance: + type: boolean + description: | + MAC Interface Impedance control to set the programmable output impedance + to a minimum value (35 ohms). + + ti,max-output-impedance: + type: boolean + description: | + MAC Interface Impedance control to set the programmable output impedance + to a maximum value (70 ohms). + Note: ti,min-output-impedance and ti,max-output-impedance are mutually + exclusive. When both properties are present ti,max-output-impedance + takes precedence. + + tx-fifo-depth: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Transmitt FIFO depth see dt-bindings/net/ti-dp83867.h for values + + rx-fifo-depth: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Receive FIFO depth see dt-bindings/net/ti-dp83867.h for values + + ti,clk-output-sel: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Muxing option for CLK_OUT pin. See dt-bindings/net/ti-dp83867.h + for applicable values. The CLK_OUT pin can also be disabled by this + property. When omitted, the PHY's default will be left as is. + + ti,rx-internal-delay: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_RXID. + + ti,tx-internal-delay: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID. + + Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock + delays will be left at their default values, as set by the PHY's pin + strapping. The default strapping will use a delay of 2.00 ns. Thus + PHY_INTERFACE_MODE_RGMII, by default, does not behave as RGMII with no + internal delay, but as PHY_INTERFACE_MODE_RGMII_ID. The device tree + should use "rgmii-id" if internal delays are desired as this may be + changed in future to cause "rgmii" mode to disable delays. + + ti,dp83867-rxctrl-strap-quirk: + type: boolean + description: | + This denotes the fact that the board has RX_DV/RX_CTRL pin strapped in + mode 1 or 2. To ensure PHY operation, there are specific actions that + software needs to take when this pin is strapped in these modes. + See data manual for details. + + ti,sgmii-ref-clock-output-enable: + type: boolean + description: | + This denotes which SGMII configuration is used (4 or 6-wire modes). + Some MACs work with differential SGMII clock. See data manual for details. + + ti,fifo-depth: + deprecated: true + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h for applicable + values. + +required: + - reg + +examples: + - | + #include <dt-bindings/net/ti-dp83867.h> + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + ethphy0: ethernet-phy@0 { + reg = <0>; + tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + rx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,max-output-impedance; + ti,clk-output-sel = <DP83867_CLK_O_SEL_CHN_A_RCLK>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ti,dp83869.yaml b/Documentation/devicetree/bindings/net/ti,dp83869.yaml index 6fe3e451da8a..5b69ef03bbf7 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83869.yaml +++ b/Documentation/devicetree/bindings/net/ti,dp83869.yaml @@ -1,4 +1,4 @@ -# SPDX-License-Identifier: GPL-2.0 +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) # Copyright (C) 2019 Texas Instruments Incorporated %YAML 1.2 --- diff --git a/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml b/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml index 78bf511e2892..c87395f360a6 100644 --- a/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml +++ b/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml @@ -144,6 +144,13 @@ patternProperties: description: CPSW MDIO bus. + "^cpts@[0-9a-f]+": + type: object + allOf: + - $ref: "ti,k3-am654-cpts.yaml#" + description: + CPSW Common Platform Time Sync (CPTS) module. + required: - compatible - reg @@ -164,6 +171,8 @@ examples: #include <dt-bindings/pinctrl/k3.h> #include <dt-bindings/soc/ti,sci_pm_domain.h> #include <dt-bindings/net/ti-dp83867.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> mcu_cpsw: ethernet@46000000 { compatible = "ti,am654-cpsw-nuss"; @@ -222,4 +231,15 @@ examples: ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; }; }; + + cpts@3d000 { + compatible = "ti,am65-cpts"; + reg = <0x0 0x3d000 0x0 0x400>; + clocks = <&k3_clks 18 2>; + clock-names = "cpts"; + interrupts-extended = <&gic500 GIC_SPI 858 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cpts"; + ti,cpts-ext-ts-inputs = <4>; + ti,cpts-periodic-outputs = <2>; + }; }; diff --git a/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml b/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml new file mode 100644 index 000000000000..50e027911dd4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml @@ -0,0 +1,145 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/ti,k3-am654-cpts.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: The TI AM654x/J721E Common Platform Time Sync (CPTS) module Device Tree Bindings + +maintainers: + - Grygorii Strashko <grygorii.strashko@ti.com> + - Sekhar Nori <nsekhar@ti.com> + +description: |+ + The TI AM654x/J721E CPTS module is used to facilitate host control of time + sync operations. + Main features of CPTS module are + - selection of multiple external clock sources + - Software control of time sync events via interrupt or polling + - 64-bit timestamp mode in ns with PPM and nudge adjustment. + - hardware timestamp push inputs (HWx_TS_PUSH) + - timestamp counter compare output (TS_COMP) + - timestamp counter bit output (TS_SYNC) + - periodic Generator function outputs (TS_GENFx) + - Ethernet Enhanced Scheduled Traffic Operations (CPTS_ESTFn) (TSN) + - external hardware timestamp push inputs (HWx_TS_PUSH) timestamping + + Depending on integration it enables compliance with the IEEE 1588-2008 + standard for a precision clock synchronization protocol, Ethernet Enhanced + Scheduled Traffic Operations (CPTS_ESTFn) and PCIe Subsystem Precision Time + Measurement (PTM). + + TI AM654x/J721E SoCs has several similar CPTS modules integrated into the + different parts of the system which could be synchronized with each other + - Main CPTS + - MCU CPSW CPTS with IEEE 1588-2008 support + - PCIe subsystem CPTS for PTM support + + Depending on CPTS module integration and when CPTS is integral part of + another module (MCU CPSW for example) "compatible" and "reg" can + be omitted - parent module is fully responsible for CPTS enabling and + configuration. + +properties: + $nodename: + pattern: "^cpts@[0-9a-f]+$" + + compatible: + oneOf: + - const: ti,am65-cpts + - const: ti,j721e-cpts + + reg: + maxItems: 1 + description: + The physical base address and size of CPTS IO range + + reg-names: + items: + - const: cpts + + clocks: + description: CPTS reference clock + + clock-names: + items: + - const: cpts + + interrupts: + items: + - description: CPTS events interrupt + + interrupt-names: + items: + - const: cpts + + ti,cpts-ext-ts-inputs: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 8 + description: + Number of hardware timestamp push inputs (HWx_TS_PUSH) + + ti,cpts-periodic-outputs: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 8 + description: + Number of timestamp Generator function outputs (TS_GENFx) + + refclk-mux: + type: object + description: CPTS reference clock multiplexer clock + properties: + '#clock-cells': + const: 0 + + clocks: + maxItems: 8 + + assigned-clocks: + maxItems: 1 + + assigned-clocks-parents: + maxItems: 1 + + required: + - clocks + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + - interrupt-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + cpts@310d0000 { + compatible = "ti,am65-cpts"; + reg = <0x0 0x310d0000 0x0 0x400>; + reg-names = "cpts"; + clocks = <&main_cpts_mux>; + clock-names = "cpts"; + interrupts-extended = <&k3_irq 163 0 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cpts"; + ti,cpts-periodic-outputs = <6>; + ti,cpts-ext-ts-inputs = <8>; + + main_cpts_mux: refclk-mux { + #clock-cells = <0>; + clocks = <&k3_clks 118 5>, <&k3_clks 118 11>, + <&k3_clks 157 91>, <&k3_clks 157 77>, + <&k3_clks 157 102>, <&k3_clks 157 80>, + <&k3_clks 120 3>, <&k3_clks 121 3>; + assigned-clocks = <&main_cpts_mux>; + assigned-clock-parents = <&k3_clks 118 11>; + }; + }; + diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt index 3a76d8faaaed..ab7e7a00e534 100644 --- a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt +++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt @@ -25,6 +25,9 @@ Optional properties: - mediatek,mtd-eeprom: Specify a MTD partition + offset containing EEPROM data - big-endian: if the radio eeprom partition is written in big-endian, specify this property +- mediatek,eeprom-merge-otp: Merge EEPROM data with OTP data. Can be used on + boards where the flash calibration data is generic and specific calibration + data should be pulled from the OTP ROM The MAC address can as well be set with corresponding optional properties defined in net/ethernet.txt. diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 71bf91f97386..65ee68efd574 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -96,6 +96,17 @@ Optional properties: - qcom,coexist-gpio-pin : gpio pin number information to support coex which will be used by wifi firmware. +* Subnodes +The ath10k wifi node can contain one optional firmware subnode. +Firmware subnode is needed when the platform does not have TustZone. +The firmware subnode must have: + +- iommus: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. + + Example (to supply PCI based wifi block details): In this example, the node is defined as child node of the PCI controller. @@ -196,4 +207,7 @@ wifi@18000000 { memory-region = <&wifi_msa_mem>; iommus = <&apps_smmu 0x0040 0x1>; qcom,msa-fixed-perm; + wifi-firmware { + iommus = <&apps_iommu 0xc22 0x1>; + }; }; |