summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/sound
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/sound')
-rw-r--r--Documentation/devicetree/bindings/sound/adi,adau1701.txt35
-rw-r--r--Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt46
-rw-r--r--Documentation/devicetree/bindings/sound/mxs-saif.txt17
-rw-r--r--Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt71
-rw-r--r--Documentation/devicetree/bindings/sound/rt5640.txt30
-rw-r--r--Documentation/devicetree/bindings/sound/sgtl5000.txt3
-rw-r--r--Documentation/devicetree/bindings/sound/spdif-receiver.txt10
-rw-r--r--Documentation/devicetree/bindings/sound/spdif-transmitter.txt10
-rw-r--r--Documentation/devicetree/bindings/sound/ssm2518.txt20
-rw-r--r--Documentation/devicetree/bindings/sound/ti,tas5086.txt11
-rw-r--r--Documentation/devicetree/bindings/sound/wm8962.txt23
11 files changed, 270 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/sound/adi,adau1701.txt b/Documentation/devicetree/bindings/sound/adi,adau1701.txt
new file mode 100644
index 000000000000..547a49b56a62
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/adi,adau1701.txt
@@ -0,0 +1,35 @@
+Analog Devices ADAU1701
+
+Required properties:
+
+ - compatible: Should contain "adi,adau1701"
+ - reg: The i2c address. Value depends on the state of ADDR0
+ and ADDR1, as wired in hardware.
+
+Optional properties:
+
+ - reset-gpio: A GPIO spec to define which pin is connected to the
+ chip's !RESET pin. If specified, the driver will
+ assert a hardware reset at probe time.
+ - adi,pll-mode-gpios: An array of two GPIO specs to describe the GPIOs
+ the ADAU's PLL config pins are connected to.
+ The state of the pins are set according to the
+ configured clock divider on ASoC side before the
+ firmware is loaded.
+ - adi,pin-config: An array of 12 numerical values selecting one of the
+ pin configurations as described in the datasheet,
+ table 53. Note that the value of this property has
+ to be prefixed with '/bits/ 8'.
+
+Examples:
+
+ i2c_bus {
+ adau1701@34 {
+ compatible = "adi,adau1701";
+ reg = <0x34>;
+ reset-gpio = <&gpio 23 0>;
+ adi,pll-mode-gpios = <&gpio 24 0 &gpio 25 0>;
+ adi,pin-config = /bits/ 8 <0x4 0x7 0x5 0x5 0x4 0x4
+ 0x4 0x4 0x4 0x4 0x4 0x4>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt
new file mode 100644
index 000000000000..f49450a87890
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt
@@ -0,0 +1,46 @@
+Freescale i.MX audio complex with WM8962 codec
+
+Required properties:
+- compatible : "fsl,imx-audio-wm8962"
+- model : The user-visible name of this sound complex
+- ssi-controller : The phandle of the i.MX SSI controller
+- audio-codec : The phandle of the WM8962 audio codec
+- audio-routing : A list of the connections between audio components.
+ Each entry is a pair of strings, the first being the connection's sink,
+ the second being the connection's source. Valid names could be power
+ supplies, WM8962 pins, and the jacks on the board:
+
+ Power supplies:
+ * Mic Bias
+
+ Board connectors:
+ * Mic Jack
+ * Headphone Jack
+ * Ext Spk
+
+- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX)
+- mux-ext-port : The external port of the i.MX audio muxer
+
+Note: The AUDMUX port numbering should start at 1, which is consistent with
+hardware manual.
+
+Example:
+
+sound {
+ compatible = "fsl,imx6q-sabresd-wm8962",
+ "fsl,imx-audio-wm8962";
+ model = "wm8962-audio";
+ ssi-controller = <&ssi2>;
+ audio-codec = <&codec>;
+ audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "Ext Spk", "SPKOUTL",
+ "Ext Spk", "SPKOUTR",
+ "MICBIAS", "AMIC",
+ "IN3R", "MICBIAS",
+ "DMIC", "MICBIAS",
+ "DMICDAT", "DMIC";
+ mux-int-port = <2>;
+ mux-ext-port = <3>;
+};
diff --git a/Documentation/devicetree/bindings/sound/mxs-saif.txt b/Documentation/devicetree/bindings/sound/mxs-saif.txt
index c37ba6143d9b..7ba07a118e37 100644
--- a/Documentation/devicetree/bindings/sound/mxs-saif.txt
+++ b/Documentation/devicetree/bindings/sound/mxs-saif.txt
@@ -3,8 +3,11 @@
Required properties:
- compatible: Should be "fsl,<chip>-saif"
- reg: Should contain registers location and length
-- interrupts: Should contain ERROR and DMA interrupts
-- fsl,saif-dma-channel: APBX DMA channel for the SAIF
+- interrupts: Should contain ERROR interrupt number
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+ and SAIF DMA channel ID.
+ Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
Optional properties:
- fsl,saif-master: phandle to the master SAIF. It's only required for
@@ -23,14 +26,16 @@ aliases {
saif0: saif@80042000 {
compatible = "fsl,imx28-saif";
reg = <0x80042000 2000>;
- interrupts = <59 80>;
- fsl,saif-dma-channel = <4>;
+ interrupts = <59>;
+ dmas = <&dma_apbx 4>;
+ dma-names = "rx-tx";
};
saif1: saif@80046000 {
compatible = "fsl,imx28-saif";
reg = <0x80046000 2000>;
- interrupts = <58 81>;
- fsl,saif-dma-channel = <5>;
+ interrupts = <58>;
+ dmas = <&dma_apbx 5>;
+ dma-names = "rx-tx";
fsl,saif-master = <&saif0>;
};
diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt
new file mode 100644
index 000000000000..d130818700b2
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt
@@ -0,0 +1,71 @@
+NVIDIA Tegra audio complex, with RT5640 CODEC
+
+Required properties:
+- compatible : "nvidia,tegra-audio-rt5640"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+ "pll_a" (The Tegra clock of that name),
+ "pll_a_out0" (The Tegra clock of that name),
+ "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+ Each entry is a pair of strings, the first being the connection's sink,
+ the second being the connection's source. Valid names for sources and
+ sinks are the RT5640's pins, and the jacks on the board:
+
+ RT5640 pins:
+
+ * DMIC1
+ * DMIC2
+ * MICBIAS1
+ * IN1P
+ * IN1R
+ * IN2P
+ * IN2R
+ * HPOL
+ * HPOR
+ * LOUTL
+ * LOUTR
+ * MONOP
+ * MONON
+ * SPOLP
+ * SPOLN
+ * SPORP
+ * SPORN
+
+ Board connectors:
+
+ * Headphones
+ * Speakers
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's
+ connected to the CODEC.
+- nvidia,audio-codec : The phandle of the RT5640 audio codec. This binding
+ assumes that AIF1 on the CODEC is connected to Tegra.
+
+Optional properties:
+- nvidia,hp-det-gpios : The GPIO that detects headphones are plugged in
+
+Example:
+
+sound {
+ compatible = "nvidia,tegra-audio-rt5640-dalmore",
+ "nvidia,tegra-audio-rt5640";
+ nvidia,model = "NVIDIA Tegra Dalmore";
+
+ nvidia,audio-routing =
+ "Headphones", "HPOR",
+ "Headphones", "HPOL",
+ "Speakers", "SPORP",
+ "Speakers", "SPORN",
+ "Speakers", "SPOLP",
+ "Speakers", "SPOLN";
+
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&rt5640>;
+
+ nvidia,hp-det-gpios = <&gpio 143 0>; /* GPIO PR7 */
+
+ clocks = <&tegra_car 216>, <&tegra_car 217>, <&tegra_car 120>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
+};
diff --git a/Documentation/devicetree/bindings/sound/rt5640.txt b/Documentation/devicetree/bindings/sound/rt5640.txt
new file mode 100644
index 000000000000..005bcb24d72d
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/rt5640.txt
@@ -0,0 +1,30 @@
+RT5640 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : "realtek,rt5640".
+
+- reg : The I2C address of the device.
+
+- interrupts : The CODEC's interrupt output.
+
+Optional properties:
+
+- realtek,in1-differential
+- realtek,in2-differential
+ Boolean. Indicate MIC1/2 input are differential, rather than single-ended.
+
+- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
+
+Example:
+
+rt5640 {
+ compatible = "realtek,rt5640";
+ reg = <0x1c>;
+ interrupt-parent = <&gpio>;
+ interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>;
+ realtek,ldo1-en-gpios =
+ <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+};
diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt
index 9cc44449508d..955df60a118c 100644
--- a/Documentation/devicetree/bindings/sound/sgtl5000.txt
+++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt
@@ -5,9 +5,12 @@ Required properties:
- reg : the I2C address of the device
+- clocks : the clock provider of SYS_MCLK
+
Example:
codec: sgtl5000@0a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
+ clocks = <&clks 150>;
};
diff --git a/Documentation/devicetree/bindings/sound/spdif-receiver.txt b/Documentation/devicetree/bindings/sound/spdif-receiver.txt
new file mode 100644
index 000000000000..80f807bf8a1d
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/spdif-receiver.txt
@@ -0,0 +1,10 @@
+Device-Tree bindings for dummy spdif receiver
+
+Required properties:
+ - compatible: should be "linux,spdif-dir".
+
+Example node:
+
+ codec: spdif-receiver {
+ compatible = "linux,spdif-dir";
+ };
diff --git a/Documentation/devicetree/bindings/sound/spdif-transmitter.txt b/Documentation/devicetree/bindings/sound/spdif-transmitter.txt
new file mode 100644
index 000000000000..55a85841dd85
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/spdif-transmitter.txt
@@ -0,0 +1,10 @@
+Device-Tree bindings for dummy spdif transmitter
+
+Required properties:
+ - compatible: should be "linux,spdif-dit".
+
+Example node:
+
+ codec: spdif-transmitter {
+ compatible = "linux,spdif-dit";
+ };
diff --git a/Documentation/devicetree/bindings/sound/ssm2518.txt b/Documentation/devicetree/bindings/sound/ssm2518.txt
new file mode 100644
index 000000000000..59381a778c79
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/ssm2518.txt
@@ -0,0 +1,20 @@
+SSM2518 audio amplifier
+
+This device supports I2C only.
+
+Required properties:
+ - compatible : Must be "adi,ssm2518"
+ - reg : the I2C address of the device. This will either be 0x34 (ADDR pin low)
+ or 0x35 (ADDR pin high)
+
+Optional properties:
+ - gpios : GPIO connected to the nSD pin. If the property is not present it is
+ assumed that the nSD pin is hardwired to always on.
+
+Example:
+
+ ssm2518: ssm2518@34 {
+ compatible = "adi,ssm2518";
+ reg = <0x34>;
+ gpios = <&gpio 5 0>;
+ };
diff --git a/Documentation/devicetree/bindings/sound/ti,tas5086.txt b/Documentation/devicetree/bindings/sound/ti,tas5086.txt
index 8ea4f5b4818d..d2866a0d6a26 100644
--- a/Documentation/devicetree/bindings/sound/ti,tas5086.txt
+++ b/Documentation/devicetree/bindings/sound/ti,tas5086.txt
@@ -20,6 +20,17 @@ Optional properties:
When not specified, the hardware default of 1300ms
is retained.
+ - ti,mid-z-channel-X: Boolean properties, X being a number from 1 to 6.
+ If given, channel X will start with the Mid-Z start
+ sequence, otherwise the default Low-Z scheme is used.
+
+ The correct configuration depends on how the power
+ stages connected to the PWM output pins work. Not all
+ power stages are compatible to Mid-Z - please refer
+ to the datasheets for more details.
+
+ Most systems should not set any of these properties.
+
Examples:
i2c_bus {
diff --git a/Documentation/devicetree/bindings/sound/wm8962.txt b/Documentation/devicetree/bindings/sound/wm8962.txt
index dceb3b1c2bb7..7f82b59ec8f9 100644
--- a/Documentation/devicetree/bindings/sound/wm8962.txt
+++ b/Documentation/devicetree/bindings/sound/wm8962.txt
@@ -8,9 +8,32 @@ Required properties:
- reg : the I2C address of the device.
+Optional properties:
+ - spk-mono: This is a boolean property. If present, the SPK_MONO bit
+ of R51 (Class D Control 2) gets set, indicating that the speaker is
+ in mono mode.
+
+ - mic-cfg : Default register value for R48 (Additional Control 4).
+ If absent, the default should be the register default.
+
+ - gpio-cfg : A list of GPIO configuration register values. The list must
+ be 6 entries long. If absent, no configuration of these registers is
+ performed. And note that only the value within [0x0, 0xffff] is valid.
+ Any other value is regarded as setting the GPIO register by its reset
+ value 0x0.
+
Example:
codec: wm8962@1a {
compatible = "wlf,wm8962";
reg = <0x1a>;
+
+ gpio-cfg = <
+ 0x0000 /* 0:Default */
+ 0x0000 /* 1:Default */
+ 0x0013 /* 2:FN_DMICCLK */
+ 0x0000 /* 3:Default */
+ 0x8014 /* 4:FN_DMICCDAT */
+ 0x0000 /* 5:Default */
+ >;
};