diff options
Diffstat (limited to 'Documentation/devicetree/bindings/video')
4 files changed, 100 insertions, 48 deletions
diff --git a/Documentation/devicetree/bindings/video/backlight/lp855x.txt b/Documentation/devicetree/bindings/video/backlight/lp855x.txt new file mode 100644 index 000000000000..1482103d288f --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/lp855x.txt @@ -0,0 +1,41 @@ +lp855x bindings + +Required properties: + - compatible: "ti,lp8550", "ti,lp8551", "ti,lp8552", "ti,lp8553", + "ti,lp8556", "ti,lp8557" + - reg: I2C slave address (u8) + - dev-ctrl: Value of DEVICE CONTROL register (u8). It depends on the device. + +Optional properties: + - bl-name: Backlight device name (string) + - init-brt: Initial value of backlight brightness (u8) + - pwm-period: PWM period value. Set only PWM input mode used (u32) + - rom-addr: Register address of ROM area to be updated (u8) + - rom-val: Register value to be updated (u8) + +Example: + + /* LP8556 */ + backlight@2c { + compatible = "ti,lp8556"; + reg = <0x2c>; + + bl-name = "lcd-bl"; + dev-ctrl = /bits/ 8 <0x85>; + init-brt = /bits/ 8 <0x10>; + }; + + /* LP8557 */ + backlight@2c { + compatible = "ti,lp8557"; + reg = <0x2c>; + + dev-ctrl = /bits/ 8 <0x41>; + init-brt = /bits/ 8 <0x0a>; + + /* 4V OV, 4 output LED string enabled */ + rom_14h { + rom-addr = /bits/ 8 <0x14>; + rom-val = /bits/ 8 <0xcf>; + }; + }; diff --git a/Documentation/devicetree/bindings/video/backlight/tps65217-backlight.txt b/Documentation/devicetree/bindings/video/backlight/tps65217-backlight.txt new file mode 100644 index 000000000000..5fb9279ac287 --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/tps65217-backlight.txt @@ -0,0 +1,27 @@ +TPS65217 family of regulators + +The TPS65217 chip contains a boost converter and current sinks which can be +used to drive LEDs for use as backlights. + +Required properties: +- compatible: "ti,tps65217" +- reg: I2C slave address +- backlight: node for specifying WLED1 and WLED2 lines in TPS65217 +- isel: selection bit, valid values: 1 for ISEL1 (low-level) and 2 for ISEL2 (high-level) +- fdim: PWM dimming frequency, valid values: 100, 200, 500, 1000 +- default-brightness: valid values: 0-100 + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps: tps@24 { + reg = <0x24>; + compatible = "ti,tps65217"; + backlight { + isel = <1>; /* 1 - ISET1, 2 ISET2 */ + fdim = <100>; /* TPS65217_BL_FDIM_100HZ */ + default-brightness = <50>; + }; + }; + diff --git a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt index c870b6478ec8..2871e218a0fb 100644 --- a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt +++ b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt @@ -5,58 +5,32 @@ Required properties: - compatible : "via,vt8500-fb" - reg : Should contain 1 register ranges(address and length) - interrupts : framebuffer controller interrupt -- display: a phandle pointing to the display node +- bits-per-pixel : bit depth of framebuffer (16 or 32) -Required nodes: -- display: a display node is required to initialize the lcd panel - This should be in the board dts. -- default-mode: a videomode within the display with timing parameters - as specified below. +Required subnodes: +- display-timings: see display-timing.txt for information Example: - fb@d800e400 { + fb@d8050800 { compatible = "via,vt8500-fb"; reg = <0xd800e400 0x400>; interrupts = <12>; - display = <&display>; - default-mode = <&mode0>; - }; - -VIA VT8500 Display ------------------------------------------------------ -Required properties (as per of_videomode_helper): - - - hactive, vactive: Display resolution - - hfront-porch, hback-porch, hsync-len: Horizontal Display timing parameters - in pixels - vfront-porch, vback-porch, vsync-len: Vertical display timing parameters in - lines - - clock: displayclock in Hz - - bpp: lcd panel bit-depth. - <16> for RGB565, <32> for RGB888 - -Optional properties (as per of_videomode_helper): - - width-mm, height-mm: Display dimensions in mm - - hsync-active-high (bool): Hsync pulse is active high - - vsync-active-high (bool): Vsync pulse is active high - - interlaced (bool): This is an interlaced mode - - doublescan (bool): This is a doublescan mode + bits-per-pixel = <16>; -Example: - display: display@0 { - modes { - mode0: mode@0 { + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ hactive = <800>; vactive = <480>; - hback-porch = <88>; hfront-porch = <40>; + hback-porch = <88>; hsync-len = <0>; vback-porch = <32>; vfront-porch = <11>; vsync-len = <1>; - clock = <0>; /* unused but required */ - bpp = <16>; /* non-standard but required */ }; }; }; + diff --git a/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt index 3d325e1d11ee..0bcadb2840a5 100644 --- a/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt +++ b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt @@ -4,20 +4,30 @@ Wondermedia WM8505 Framebuffer Required properties: - compatible : "wm,wm8505-fb" - reg : Should contain 1 register ranges(address and length) -- via,display: a phandle pointing to the display node +- bits-per-pixel : bit depth of framebuffer (16 or 32) -Required nodes: -- display: a display node is required to initialize the lcd panel - This should be in the board dts. See definition in - Documentation/devicetree/bindings/video/via,vt8500-fb.txt -- default-mode: a videomode node as specified in - Documentation/devicetree/bindings/video/via,vt8500-fb.txt +Required subnodes: +- display-timings: see display-timing.txt for information Example: - fb@d8050800 { + fb@d8051700 { compatible = "wm,wm8505-fb"; - reg = <0xd8050800 0x200>; - display = <&display>; - default-mode = <&mode0>; + reg = <0xd8051700 0x200>; + bits-per-pixel = <16>; + + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <88>; + hsync-len = <0>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <1>; + }; + }; }; |