diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
21 files changed, 478 insertions, 18 deletions
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 34dc40cffdfd..af9b4a0d902b 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -91,7 +91,7 @@ Boards: compatible = "ti,omap3-beagle", "ti,omap3" - OMAP3 Tobi with Overo : Commercial expansion board with daughter board - compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3" + compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3" - OMAP4 SDP : Software Development Board compatible = "ti,omap4-sdp", "ti,omap4430" diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt index a6a352c2771e..5992dceec7af 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt @@ -21,9 +21,9 @@ Required Properties: must appear in the same order as the output clocks. - #clock-cells: Must be 1 - clock-output-names: The name of the clocks as free-form strings - - renesas,indices: Indices of the gate clocks into the group (0 to 31) + - renesas,clock-indices: Indices of the gate clocks into the group (0 to 31) -The clocks, clock-output-names and renesas,indices properties contain one +The clocks, clock-output-names and renesas,clock-indices properties contain one entry per gate clock. The MSTP groups are sparsely populated. Unimplemented gate clocks must not be declared. diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index 68b83ecc3850..ee9be9961524 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -1,12 +1,16 @@ * Freescale Smart Direct Memory Access (SDMA) Controller for i.MX Required properties: -- compatible : Should be "fsl,imx31-sdma", "fsl,imx31-to1-sdma", - "fsl,imx31-to2-sdma", "fsl,imx35-sdma", "fsl,imx35-to1-sdma", - "fsl,imx35-to2-sdma", "fsl,imx51-sdma", "fsl,imx53-sdma" or - "fsl,imx6q-sdma". The -to variants should be preferred since they - allow to determnine the correct ROM script addresses needed for - the driver to work without additional firmware. +- compatible : Should be one of + "fsl,imx25-sdma" + "fsl,imx31-sdma", "fsl,imx31-to1-sdma", "fsl,imx31-to2-sdma" + "fsl,imx35-sdma", "fsl,imx35-to1-sdma", "fsl,imx35-to2-sdma" + "fsl,imx51-sdma" + "fsl,imx53-sdma" + "fsl,imx6q-sdma" + The -to variants should be preferred since they allow to determnine the + correct ROM script addresses needed for the driver to work without additional + firmware. - reg : Should contain SDMA registers location and length - interrupts : Should contain SDMA interrupt - #dma-cells : Must be <3>. diff --git a/Documentation/devicetree/bindings/drm/bridge/ptn3460.txt b/Documentation/devicetree/bindings/drm/bridge/ptn3460.txt new file mode 100644 index 000000000000..52b93b2c6748 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/bridge/ptn3460.txt @@ -0,0 +1,27 @@ +ptn3460 bridge bindings + +Required properties: + - compatible: "nxp,ptn3460" + - reg: i2c address of the bridge + - powerdown-gpio: OF device-tree gpio specification + - reset-gpio: OF device-tree gpio specification + - edid-emulation: The EDID emulation entry to use + +-------+------------+------------------+ + | Value | Resolution | Description | + | 0 | 1024x768 | NXP Generic | + | 1 | 1920x1080 | NXP Generic | + | 2 | 1920x1080 | NXP Generic | + | 3 | 1600x900 | Samsung LTM200KT | + | 4 | 1920x1080 | Samsung LTM230HT | + | 5 | 1366x768 | NXP Generic | + | 6 | 1600x900 | ChiMei M215HGE | + +-------+------------+------------------+ + +Example: + lvds-bridge@20 { + compatible = "nxp,ptn3460"; + reg = <0x20>; + powerdown-gpio = <&gpy2 5 1 0 0>; + reset-gpio = <&gpx1 5 1 0 0>; + edid-emulation = <5>; + }; diff --git a/Documentation/devicetree/bindings/drm/i2c/tda998x.txt b/Documentation/devicetree/bindings/drm/i2c/tda998x.txt new file mode 100644 index 000000000000..d7df01c5bb3a --- /dev/null +++ b/Documentation/devicetree/bindings/drm/i2c/tda998x.txt @@ -0,0 +1,27 @@ +Device-Tree bindings for the NXP TDA998x HDMI transmitter + +Required properties; + - compatible: must be "nxp,tda998x" + +Optional properties: + - interrupts: interrupt number and trigger type + default: polling + + - pinctrl-0: pin control group to be used for + screen plug/unplug interrupt. + + - pinctrl-names: must contain a "default" entry. + + - video-ports: 24 bits value which defines how the video controller + output is wired to the TDA998x input - default: <0x230145> + +Example: + + tda998x: hdmi-encoder { + compatible = "nxp,tda998x"; + reg = <0x70>; + interrupt-parent = <&gpio0>; + interrupts = <27 2>; /* falling edge */ + pinctrl-0 = <&pmx_camera>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt new file mode 100644 index 000000000000..aee38e7c13e7 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt @@ -0,0 +1,18 @@ +TI-NSPIRE interrupt controller + +Required properties: +- compatible: Compatible property value should be "lsi,zevio-intc". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- interrupt-controller : Identifies the node as an interrupt controller + +Example: + +interrupt-controller { + compatible = "lsi,zevio-intc"; + interrupt-controller; + reg = <0xDC000000 0x1000>; + #interrupt-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt index 0a85c70cd30a..07ad02075a93 100644 --- a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt +++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt @@ -13,6 +13,9 @@ Required properties: - #address-cells: should be one. The cell is the slot id. - #size-cells: should be zero. - at least one slot node +- clock-names: tuple listing input clock names. + Required elements: "mci_clk" +- clocks: phandles to input clocks. The node contains child nodes for each slot that the platform uses @@ -24,6 +27,8 @@ mmc0: mmc@f0008000 { interrupts = <12 4>; #address-cells = <1>; #size-cells = <0>; + clock-names = "mci_clk"; + clocks = <&mci0_clk>; [ child node definitions...] }; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt index b90bfcd138ff..863d5b8155c7 100644 --- a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt @@ -1,7 +1,8 @@ * Allwinner EMAC ethernet controller Required properties: -- compatible: should be "allwinner,sun4i-emac". +- compatible: should be "allwinner,sun4i-a10-emac" (Deprecated: + "allwinner,sun4i-emac") - reg: address and length of the register set for the device. - interrupts: interrupt for the device - phy: A phandle to a phy node defining the PHY address (as the reg @@ -14,7 +15,7 @@ Optional properties: Example: emac: ethernet@01c0b000 { - compatible = "allwinner,sun4i-emac"; + compatible = "allwinner,sun4i-a10-emac"; reg = <0x01c0b000 0x1000>; interrupts = <55>; clocks = <&ahb_gates 17>; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt index 00b9f9a3ec1d..4ec56413779d 100644 --- a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt @@ -1,7 +1,8 @@ * Allwinner A10 MDIO Ethernet Controller interface Required properties: -- compatible: should be "allwinner,sun4i-mdio". +- compatible: should be "allwinner,sun4i-a10-mdio" + (Deprecated: "allwinner,sun4i-mdio"). - reg: address and length of the register set for the device. Optional properties: @@ -9,7 +10,7 @@ Optional properties: Example at the SoC level: mdio@01c0b080 { - compatible = "allwinner,sun4i-mdio"; + compatible = "allwinner,sun4i-a10-mdio"; reg = <0x01c0b080 0x14>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/opencores-ethoc.txt b/Documentation/devicetree/bindings/net/opencores-ethoc.txt new file mode 100644 index 000000000000..2dc127c30d9b --- /dev/null +++ b/Documentation/devicetree/bindings/net/opencores-ethoc.txt @@ -0,0 +1,22 @@ +* OpenCores MAC 10/100 Mbps + +Required properties: +- compatible: Should be "opencores,ethoc". +- reg: two memory regions (address and length), + first region is for the device registers and descriptor rings, + second is for the device packet memory. +- interrupts: interrupt for the device. + +Optional properties: +- clocks: phandle to refer to the clk used as per + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Examples: + + enet0: ethoc@fd030000 { + compatible = "opencores,ethoc"; + reg = <0xfd030000 0x4000 0xfd800000 0x4000>; + interrupts = <1>; + local-mac-address = [00 50 c2 13 6f 00]; + clocks = <&osc>; + }; diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt new file mode 100644 index 000000000000..3dd3d0bf112f --- /dev/null +++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt @@ -0,0 +1,58 @@ +STMicroelectronics SoC DWMAC glue layer controller + +The device node has following properties. + +Required properties: + - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac" or + "st,stid127-dwmac". + - reg : Offset of the glue configuration register map in system + configuration regmap pointed by st,syscon property and size. + + - reg-names : Should be "sti-ethconf". + + - st,syscon : Should be phandle to system configuration node which + encompases this glue registers. + + - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be + wired up in from different sources. One via TXCLK pin and other via CLK_125 + pin. This wiring is totally board dependent. However the retiming glue + logic should be configured accordingly. Possible values for this property + + "txclk" - if 125Mhz clock is wired up via txclk line. + "clk_125" - if 125Mhz clock is wired up via clk_125 line. + + This property is only valid for Giga bit setup( GMII, RGMII), and it is + un-used for non-giga bit (MII and RMII) setups. Also note that internal + clockgen can not generate stable 125Mhz clock. + + - st,ext-phyclk: This boolean property indicates who is generating the clock + for tx and rx. This property is only valid for RMII case where the clock can + be generated from the MAC or PHY. + + - clock-names: should be "sti-ethclk". + - clocks: Should point to ethernet clockgen which can generate phyclk. + + +Example: + +ethernet0: dwmac@fe810000 { + device_type = "network"; + compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + reg = <0xfe810000 0x8000>, <0x8bc 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + interrupts = <0 133 0>, <0 134 0>, <0 135 0>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + phy-mode = "mii"; + + st,syscon = <&syscfg_rear>; + + snps,pbl = <32>; + snps,mixed-burst; + + resets = <&softreset STIH416_ETH0_SOFTRESET>; + reset-names = "stmmaceth"; + pinctrl-0 = <&pinctrl_mii0>; + pinctrl-names = "default"; + clocks = <&CLK_S_GMAC0_PHY>; + clock-names = "stmmaceth"; +}; diff --git a/Documentation/devicetree/bindings/panel/samsung,ld9040.txt b/Documentation/devicetree/bindings/panel/samsung,ld9040.txt new file mode 100644 index 000000000000..07c36c3f7b52 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/samsung,ld9040.txt @@ -0,0 +1,66 @@ +Samsung LD9040 AMOLED LCD parallel RGB panel with SPI control bus + +Required properties: + - compatible: "samsung,ld9040" + - reg: address of the panel on SPI bus + - vdd3-supply: core voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin + - display-timings: timings for the connected panel according to [1] + +The panel must obey rules for SPI slave device specified in document [2]. + +Optional properties: + - power-on-delay: delay after turning regulators on [ms] + - reset-delay: delay after reset sequence [ms] + - panel-width-mm: physical panel width [mm] + - panel-height-mm: physical panel height [mm] + +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in [3]. This +node should describe panel's video bus. + +[1]: Documentation/devicetree/bindings/video/display-timing.txt +[2]: Documentation/devicetree/bindings/spi/spi-bus.txt +[3]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + lcd@0 { + compatible = "samsung,ld9040"; + reg = <0>; + vdd3-supply = <&ldo7_reg>; + vci-supply = <&ldo17_reg>; + reset-gpios = <&gpy4 5 0>; + spi-max-frequency = <1200000>; + spi-cpol; + spi-cpha; + power-on-delay = <10>; + reset-delay = <10>; + panel-width-mm = <90>; + panel-height-mm = <154>; + + display-timings { + timing { + clock-frequency = <23492370>; + hactive = <480>; + vactive = <800>; + hback-porch = <16>; + hfront-porch = <16>; + vback-porch = <2>; + vfront-porch = <28>; + hsync-len = <2>; + vsync-len = <1>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <0>; + pixelclk-active = <0>; + }; + }; + + port { + lcd_ep: endpoint { + remote-endpoint = <&fimd_dpi_ep>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/panel/samsung,s6e8aa0.txt b/Documentation/devicetree/bindings/panel/samsung,s6e8aa0.txt new file mode 100644 index 000000000000..e7ee988e3156 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/samsung,s6e8aa0.txt @@ -0,0 +1,56 @@ +Samsung S6E8AA0 AMOLED LCD 5.3 inch panel + +Required properties: + - compatible: "samsung,s6e8aa0" + - reg: the virtual channel number of a DSI peripheral + - vdd3-supply: core voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin + - display-timings: timings for the connected panel as described by [1] + +Optional properties: + - power-on-delay: delay after turning regulators on [ms] + - reset-delay: delay after reset sequence [ms] + - init-delay: delay after initialization sequence [ms] + - panel-width-mm: physical panel width [mm] + - panel-height-mm: physical panel height [mm] + - flip-horizontal: boolean to flip image horizontally + - flip-vertical: boolean to flip image vertically + +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in [2]. This +node should describe panel's video bus. + +[1]: Documentation/devicetree/bindings/video/display-timing.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + panel { + compatible = "samsung,s6e8aa0"; + reg = <0>; + vdd3-supply = <&vcclcd_reg>; + vci-supply = <&vlcd_reg>; + reset-gpios = <&gpy4 5 0>; + power-on-delay= <50>; + reset-delay = <100>; + init-delay = <100>; + panel-width-mm = <58>; + panel-height-mm = <103>; + flip-horizontal; + flip-vertical; + + display-timings { + timing0: timing-0 { + clock-frequency = <57153600>; + hactive = <720>; + vactive = <1280>; + hfront-porch = <5>; + hback-porch = <5>; + hsync-len = <5>; + vfront-porch = <13>; + vback-porch = <1>; + vsync-len = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt index 9e9e9ef9f852..c119debe6bab 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt @@ -1,4 +1,4 @@ -Broadcom Capri Pin Controller +Broadcom BCM281xx Pin Controller This is a pin controller for the Broadcom BCM281xx SoC family, which includes BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs. @@ -7,14 +7,14 @@ BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs. Required Properties: -- compatible: Must be "brcm,capri-pinctrl". +- compatible: Must be "brcm,bcm11351-pinctrl" - reg: Base address of the PAD Controller register block and the size of the block. For example, the following is the bare minimum node: pinctrl@35004800 { - compatible = "brcm,capri-pinctrl"; + compatible = "brcm,bcm11351-pinctrl"; reg = <0x35004800 0x430>; }; @@ -119,7 +119,7 @@ Optional Properties (for HDMI pins): Example: // pin controller node pinctrl@35004800 { - compatible = "brcm,capri-pinctrl"; + compatible = "brcmbcm11351-pinctrl"; reg = <0x35004800 0x430>; // pin configuration node diff --git a/Documentation/devicetree/bindings/power/bq2415x.txt b/Documentation/devicetree/bindings/power/bq2415x.txt new file mode 100644 index 000000000000..d0327f0b59ad --- /dev/null +++ b/Documentation/devicetree/bindings/power/bq2415x.txt @@ -0,0 +1,47 @@ +Binding for TI bq2415x Li-Ion Charger + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq24150" + * "ti,bq24150" + * "ti,bq24150a" + * "ti,bq24151" + * "ti,bq24151a" + * "ti,bq24152" + * "ti,bq24153" + * "ti,bq24153a" + * "ti,bq24155" + * "ti,bq24156" + * "ti,bq24156a" + * "ti,bq24158" +- reg: integer, i2c address of the device. +- ti,current-limit: integer, initial maximum current charger can pull + from power supply in mA. +- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV. + The chip will use slow precharge if battery voltage + is below this value. +- ti,battery-regulation-voltage: integer, maximum charging voltage in mV. +- ti,charge-current: integer, maximum charging current in mA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in mA). +- ti,resistor-sense: integer, value of sensing resistor in milliohm. + +Optional properties: +- ti,usb-charger-detection: phandle to usb charger detection device. + (required for auto mode) + +Example from Nokia N900: + +bq24150a { + compatible = "ti,bq24150a"; + reg = <0x6b>; + + ti,current-limit = <100>; + ti,weak-battery-voltage = <3400>; + ti,battery-regulation-voltage = <4200>; + ti,charge-current = <650>; + ti,termination-current = <100>; + ti,resistor-sense = <68>; + + ti,usb-charger-detection = <&isp1704>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt index 07e04cdc0c9e..4f8184d069cb 100644 --- a/Documentation/devicetree/bindings/spi/spi_atmel.txt +++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt @@ -5,6 +5,9 @@ Required properties: - reg: Address and length of the register set for the device - interrupts: Should contain spi interrupt - cs-gpios: chipselects +- clock-names: tuple listing input clock names. + Required elements: "spi_clk" +- clocks: phandles to input clocks. Example: @@ -14,6 +17,8 @@ spi1: spi@fffcc000 { interrupts = <13 4 5>; #address-cells = <1>; #size-cells = <0>; + clocks = <&spi1_clk>; + clock-names = "spi_clk"; cs-gpios = <&pioB 3 0>; status = "okay"; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 3f900cd51bf0..40ce2df0e0e9 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -8,6 +8,7 @@ ad Avionic Design GmbH adi Analog Devices, Inc. aeroflexgaisler Aeroflex Gaisler AB ak Asahi Kasei Corp. +allwinner Allwinner Technology Co., Ltd. altr Altera Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) amstaos AMS-Taos Inc. @@ -40,6 +41,7 @@ gmt Global Mixed-mode Technology, Inc. gumstix Gumstix, Inc. haoyu Haoyu Microelectronic Co. Ltd. hisilicon Hisilicon Limited. +honeywell Honeywell hp Hewlett Packard ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. @@ -55,6 +57,7 @@ maxim Maxim Integrated Products microchip Microchip Technology Inc. mosaixtech Mosaix Technologies, Inc. national National Semiconductor +neonode Neonode Inc. nintendo Nintendo nvidia NVIDIA nxp NXP Semiconductors @@ -64,7 +67,7 @@ phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. -qcom Qualcomm, Inc. +qcom Qualcomm Technologies, Inc ralink Mediatek/Ralink Technology Corp. ramtron Ramtron International realtek Realtek Semiconductor Corp. @@ -78,6 +81,7 @@ silabs Silicon Laboratories simtek sirf SiRF Technology, Inc. snps Synopsys, Inc. +spansion Spansion Inc. st STMicroelectronics ste ST-Ericsson stericsson ST-Ericsson diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt index 3289d76a21d0..57ccdde02c3a 100644 --- a/Documentation/devicetree/bindings/video/exynos_dp.txt +++ b/Documentation/devicetree/bindings/video/exynos_dp.txt @@ -49,6 +49,8 @@ Required properties for dp-controller: -samsung,lane-count: number of lanes supported by the panel. LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 + - display-timings: timings for the connected panel as described by + Documentation/devicetree/bindings/video/display-timing.txt Optional properties for dp-controller: -interlaced: @@ -84,4 +86,19 @@ Board Specific portion: samsung,color-depth = <1>; samsung,link-rate = <0x0a>; samsung,lane-count = <4>; + + display-timings { + native-mode = <&lcd_timing>; + lcd_timing: 1366x768 { + clock-frequency = <70589280>; + hactive = <1366>; + vactive = <768>; + hfront-porch = <40>; + hback-porch = <40>; + hsync-len = <32>; + vback-porch = <10>; + vfront-porch = <12>; + vsync-len = <6>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/video/exynos_dsim.txt b/Documentation/devicetree/bindings/video/exynos_dsim.txt new file mode 100644 index 000000000000..33b5730d07ba --- /dev/null +++ b/Documentation/devicetree/bindings/video/exynos_dsim.txt @@ -0,0 +1,80 @@ +Exynos MIPI DSI Master + +Required properties: + - compatible: "samsung,exynos4210-mipi-dsi" + - reg: physical base address and length of the registers set for the device + - interrupts: should contain DSI interrupt + - clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names + - clock-names: should include "bus_clk"and "pll_clk" entries + - phys: list of phy specifiers, must contain an entry for each required + entry in phy-names + - phy-names: should include "dsim" entry + - vddcore-supply: MIPI DSIM Core voltage supply (e.g. 1.1V) + - vddio-supply: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V) + - samsung,pll-clock-frequency: specifies frequency of the "pll_clk" clock + - #address-cells, #size-cells: should be set respectively to <1> and <0> + according to DSI host bindings (see MIPI DSI bindings [1]) + +Optional properties: + - samsung,power-domain: a phandle to DSIM power domain node + +Child nodes: + Should contain DSI peripheral nodes (see MIPI DSI bindings [1]). + +Video interfaces: + Device node can contain video interface port nodes according to [2]. + The following are properties specific to those nodes: + + port node: + - reg: (required) can be 0 for input RGB/I80 port or 1 for DSI port; + + endpoint node of DSI port (reg = 1): + - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst + mode + - samsung,esc-clock-frequency: specifies DSI frequency in escape mode + +[1]: Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + dsi@11C80000 { + compatible = "samsung,exynos4210-mipi-dsi"; + reg = <0x11C80000 0x10000>; + interrupts = <0 79 0>; + clocks = <&clock 286>, <&clock 143>; + clock-names = "bus_clk", "pll_clk"; + phys = <&mipi_phy 1>; + phy-names = "dsim"; + vddcore-supply = <&vusb_reg>; + vddio-supply = <&vmipi_reg>; + samsung,power-domain = <&pd_lcd0>; + #address-cells = <1>; + #size-cells = <0>; + samsung,pll-clock-frequency = <24000000>; + + panel@1 { + reg = <0>; + ... + port { + panel_ep: endpoint { + remote-endpoint = <&dsi_ep>; + }; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + dsi_ep: endpoint { + reg = <0>; + samsung,burst-clock-frequency = <500000000>; + samsung,esc-clock-frequency = <20000000>; + remote-endpoint = <&panel_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/exynos_hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt index 50decf8e1b90..f9187a259259 100644 --- a/Documentation/devicetree/bindings/video/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt @@ -25,6 +25,9 @@ Required properties: sclk_pixel. - clock-names: aliases as per driver requirements for above clock IDs: "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi". +- ddc: phandle to the hdmi ddc node +- phy: phandle to the hdmi phy node + Example: hdmi { @@ -32,4 +35,6 @@ Example: reg = <0x14530000 0x100000>; interrupts = <0 95 0>; hpd-gpio = <&gpx3 7 1>; + ddc = <&hdmi_ddc_node>; + phy = <&hdmi_phy_node>; }; diff --git a/Documentation/devicetree/bindings/video/samsung-fimd.txt b/Documentation/devicetree/bindings/video/samsung-fimd.txt index 778838a0336a..2dad41b689af 100644 --- a/Documentation/devicetree/bindings/video/samsung-fimd.txt +++ b/Documentation/devicetree/bindings/video/samsung-fimd.txt @@ -39,6 +39,23 @@ Required properties: Optional Properties: - samsung,power-domain: a phandle to FIMD power domain node. +- samsung,invert-vden: video enable signal is inverted +- samsung,invert-vclk: video clock signal is inverted +- display-timings: timing settings for FIMD, as described in document [1]. + Can be used in case timings cannot be provided otherwise + or to override timings provided by the panel. + +The device node can contain 'port' child nodes according to the bindings defined +in [2]. The following are properties specific to those nodes: +- reg: (required) port index, can be: + 0 - for CAMIF0 input, + 1 - for CAMIF1 input, + 2 - for CAMIF2 input, + 3 - for parallel output, + 4 - for write-back interface + +[1]: Documentation/devicetree/bindings/video/display-timing.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt Example: |