diff options
Diffstat (limited to 'Documentation/networking/device_drivers/appletalk/cops.rst')
-rw-r--r-- | Documentation/networking/device_drivers/appletalk/cops.rst | 80 |
1 files changed, 0 insertions, 80 deletions
diff --git a/Documentation/networking/device_drivers/appletalk/cops.rst b/Documentation/networking/device_drivers/appletalk/cops.rst deleted file mode 100644 index 964ba80599a9..000000000000 --- a/Documentation/networking/device_drivers/appletalk/cops.rst +++ /dev/null @@ -1,80 +0,0 @@ -.. SPDX-License-Identifier: GPL-2.0 - -======================================== -The COPS LocalTalk Linux driver (cops.c) -======================================== - -By Jay Schulist <jschlst@samba.org> - -This driver has two modes and they are: Dayna mode and Tangent mode. -Each mode corresponds with the type of card. It has been found -that there are 2 main types of cards and all other cards are -the same and just have different names or only have minor differences -such as more IO ports. As this driver is tested it will -become more clear exactly what cards are supported. - -Right now these cards are known to work with the COPS driver. The -LT-200 cards work in a somewhat more limited capacity than the -DL200 cards, which work very well and are in use by many people. - -TANGENT driver mode: - - Tangent ATB-II, Novell NL-1000, Daystar Digital LT-200 - -DAYNA driver mode: - - Dayna DL2000/DaynaTalk PC (Half Length), COPS LT-95, - - Farallon PhoneNET PC III, Farallon PhoneNET PC II - -Other cards possibly supported mode unknown though: - - Dayna DL2000 (Full length) - -The COPS driver defaults to using Dayna mode. To change the driver's -mode if you built a driver with dual support use board_type=1 or -board_type=2 for Dayna or Tangent with insmod. - -Operation/loading of the driver -=============================== - -Use modprobe like this: /sbin/modprobe cops.o (IO #) (IRQ #) -If you do not specify any options the driver will try and use the IO = 0x240, -IRQ = 5. As of right now I would only use IRQ 5 for the card, if autoprobing. - -To load multiple COPS driver Localtalk cards you can do one of the following:: - - insmod cops io=0x240 irq=5 - insmod -o cops2 cops io=0x260 irq=3 - -Or in lilo.conf put something like this:: - - append="ether=5,0x240,lt0 ether=3,0x260,lt1" - -Then bring up the interface with ifconfig. It will look something like this:: - - lt0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-F7-00-00-00-00-00-00-00-00 - inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 - UP BROADCAST RUNNING NOARP MULTICAST MTU:600 Metric:1 - RX packets:0 errors:0 dropped:0 overruns:0 frame:0 - TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 coll:0 - -Netatalk Configuration -====================== - -You will need to configure atalkd with something like the following to make -it work with the cops.c driver. - -* For single LTalk card use:: - - dummy -seed -phase 2 -net 2000 -addr 2000.10 -zone "1033" - lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033" - -* For multiple cards, Ethernet and LocalTalk:: - - eth0 -seed -phase 2 -net 3000 -addr 3000.20 -zone "1033" - lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033" - -* For multiple LocalTalk cards, and an Ethernet card. - -* Order seems to matter here, Ethernet last:: - - lt0 -seed -phase 1 -net 1000 -addr 1000.10 -zone "LocalTalk1" - lt1 -seed -phase 1 -net 2000 -addr 2000.20 -zone "LocalTalk2" - eth0 -seed -phase 2 -net 3000 -addr 3000.30 -zone "EtherTalk" |