diff options
Diffstat (limited to 'Documentation/networking')
-rw-r--r-- | Documentation/networking/dccp.txt | 54 |
1 files changed, 42 insertions, 12 deletions
diff --git a/Documentation/networking/dccp.txt b/Documentation/networking/dccp.txt index 39131a3c78f8..fcfc12534428 100644 --- a/Documentation/networking/dccp.txt +++ b/Documentation/networking/dccp.txt @@ -45,6 +45,25 @@ http://linux-net.osdl.org/index.php/DCCP_Testing#Experimental_DCCP_source_tree Socket options ============== +DCCP_SOCKOPT_QPOLICY_ID sets the dequeuing policy for outgoing packets. It takes +a policy ID as argument and can only be set before the connection (i.e. changes +during an established connection are not supported). Currently, two policies are +defined: the "simple" policy (DCCPQ_POLICY_SIMPLE), which does nothing special, +and a priority-based variant (DCCPQ_POLICY_PRIO). The latter allows to pass an +u32 priority value as ancillary data to sendmsg(), where higher numbers indicate +a higher packet priority (similar to SO_PRIORITY). This ancillary data needs to +be formatted using a cmsg(3) message header filled in as follows: + cmsg->cmsg_level = SOL_DCCP; + cmsg->cmsg_type = DCCP_SCM_PRIORITY; + cmsg->cmsg_len = CMSG_LEN(sizeof(uint32_t)); /* or CMSG_LEN(4) */ + +DCCP_SOCKOPT_QPOLICY_TXQLEN sets the maximum length of the output queue. A zero +value is always interpreted as unbounded queue length. If different from zero, +the interpretation of this parameter depends on the current dequeuing policy +(see above): the "simple" policy will enforce a fixed queue size by returning +EAGAIN, whereas the "prio" policy enforces a fixed queue length by dropping the +lowest-priority packet first. The default value for this parameter is +initialised from /proc/sys/net/dccp/default/tx_qlen. DCCP_SOCKOPT_SERVICE sets the service. The specification mandates use of service codes (RFC 4340, sec. 8.1.2); if this socket option is not set, @@ -57,6 +76,24 @@ can be set before calling bind(). DCCP_SOCKOPT_GET_CUR_MPS is read-only and retrieves the current maximum packet size (application payload size) in bytes, see RFC 4340, section 14. +DCCP_SOCKOPT_AVAILABLE_CCIDS is also read-only and returns the list of CCIDs +supported by the endpoint (see include/linux/dccp.h for symbolic constants). +The caller needs to provide a sufficiently large (> 2) array of type uint8_t. + +DCCP_SOCKOPT_CCID is write-only and sets both the TX and RX CCIDs at the same +time, combining the operation of the next two socket options. This option is +preferrable over the latter two, since often applications will use the same +type of CCID for both directions; and mixed use of CCIDs is not currently well +understood. This socket option takes as argument at least one uint8_t value, or +an array of uint8_t values, which must match available CCIDS (see above). CCIDs +must be registered on the socket before calling connect() or listen(). + +DCCP_SOCKOPT_TX_CCID is read/write. It returns the current CCID (if set) or sets +the preference list for the TX CCID, using the same format as DCCP_SOCKOPT_CCID. +Please note that the getsockopt argument type here is `int', not uint8_t. + +DCCP_SOCKOPT_RX_CCID is analogous to DCCP_SOCKOPT_TX_CCID, but for the RX CCID. + DCCP_SOCKOPT_SERVER_TIMEWAIT enables the server (listening socket) to hold timewait state when closing the connection (RFC 4340, 8.3). The usual case is that the closing server sends a CloseReq, whereupon the client holds timewait @@ -115,23 +152,16 @@ retries2 importance for retransmitted acknowledgments and feature negotiation, data packets are never retransmitted. Analogue of tcp_retries2. -send_ndp = 1 - Whether or not to send NDP count options (sec. 7.7.2). - -send_ackvec = 1 - Whether or not to send Ack Vector options (sec. 11.5). - -ack_ratio = 2 - The default Ack Ratio (sec. 11.3) to use. - tx_ccid = 2 - Default CCID for the sender-receiver half-connection. + Default CCID for the sender-receiver half-connection. Depending on the + choice of CCID, the Send Ack Vector feature is enabled automatically. rx_ccid = 2 - Default CCID for the receiver-sender half-connection. + Default CCID for the receiver-sender half-connection; see tx_ccid. seq_window = 100 - The initial sequence window (sec. 7.5.2). + The initial sequence window (sec. 7.5.2) of the sender. This influences + the local ackno validity and the remote seqno validity windows (7.5.1). tx_qlen = 5 The size of the transmit buffer in packets. A value of 0 corresponds |