diff options
Diffstat (limited to 'arch/arm/mach-omap2/omap_hwmod.h')
| -rw-r--r-- | arch/arm/mach-omap2/omap_hwmod.h | 22 |
1 files changed, 13 insertions, 9 deletions
diff --git a/arch/arm/mach-omap2/omap_hwmod.h b/arch/arm/mach-omap2/omap_hwmod.h index d43d9b608eda..0c898f58ac9b 100644 --- a/arch/arm/mach-omap2/omap_hwmod.h +++ b/arch/arm/mach-omap2/omap_hwmod.h @@ -427,8 +427,8 @@ struct omap_hwmod_omap4_prcm { * * HWMOD_SWSUP_SIDLE: omap_hwmod code should manually bring module in and out * of idle, rather than relying on module smart-idle - * HWMOD_SWSUP_MSTDBY: omap_hwmod code should manually bring module in and out - * of standby, rather than relying on module smart-standby + * HWMOD_SWSUP_MSTANDBY: omap_hwmod code should manually bring module in and + * out of standby, rather than relying on module smart-standby * HWMOD_INIT_NO_RESET: don't reset this module at boot - important for * SDRAM controller, etc. XXX probably belongs outside the main hwmod file * XXX Should be HWMOD_SETUP_NO_RESET @@ -459,6 +459,13 @@ struct omap_hwmod_omap4_prcm { * correctly, or this is being abused to deal with some PM latency * issues -- but we're currently suffering from a shortage of * folks who are able to track these issues down properly. + * HWMOD_FORCE_MSTANDBY: Always keep MIDLEMODE bits cleared so that device + * is kept in force-standby mode. Failing to do so causes PM problems + * with musb on OMAP3630 at least. Note that musb has a dedicated register + * to control MSTANDBY signal when MIDLEMODE is set to force-standby. + * HWMOD_SWSUP_SIDLE_ACT: omap_hwmod code should manually bring the module + * out of idle, but rely on smart-idle to the put it back in idle, + * so the wakeups are still functional (Only known case for now is UART) */ #define HWMOD_SWSUP_SIDLE (1 << 0) #define HWMOD_SWSUP_MSTANDBY (1 << 1) @@ -471,21 +478,21 @@ struct omap_hwmod_omap4_prcm { #define HWMOD_16BIT_REG (1 << 8) #define HWMOD_EXT_OPT_MAIN_CLK (1 << 9) #define HWMOD_BLOCK_WFI (1 << 10) +#define HWMOD_FORCE_MSTANDBY (1 << 11) +#define HWMOD_SWSUP_SIDLE_ACT (1 << 12) /* * omap_hwmod._int_flags definitions * These are for internal use only and are managed by the omap_hwmod code. * * _HWMOD_NO_MPU_PORT: no path exists for the MPU to write to this module - * _HWMOD_WAKEUP_ENABLED: set when the omap_hwmod code has enabled ENAWAKEUP * _HWMOD_SYSCONFIG_LOADED: set when the OCP_SYSCONFIG value has been cached * _HWMOD_SKIP_ENABLE: set if hwmod enabled during init (HWMOD_INIT_NO_IDLE) - * causes the first call to _enable() to only update the pinmux */ #define _HWMOD_NO_MPU_PORT (1 << 0) -#define _HWMOD_WAKEUP_ENABLED (1 << 1) -#define _HWMOD_SYSCONFIG_LOADED (1 << 2) -#define _HWMOD_SKIP_ENABLE (1 << 3) +#define _HWMOD_SYSCONFIG_LOADED (1 << 1) +#define _HWMOD_SKIP_ENABLE (1 << 2) /* * omap_hwmod._state definitions @@ -638,9 +645,6 @@ int omap_hwmod_read_hardreset(struct omap_hwmod *oh, const char *name); int omap_hwmod_enable_clocks(struct omap_hwmod *oh); int omap_hwmod_disable_clocks(struct omap_hwmod *oh); -int omap_hwmod_set_slave_idlemode(struct omap_hwmod *oh, u8 idlemode); -int omap_hwmod_set_ocp_autoidle(struct omap_hwmod *oh, u8 autoidle); - int omap_hwmod_reset(struct omap_hwmod *oh); void omap_hwmod_ocp_barrier(struct omap_hwmod *oh); |