diff options
Diffstat (limited to 'arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi')
-rw-r--r-- | arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi | 56 |
1 files changed, 53 insertions, 3 deletions
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi index 58ce569b2ace..344573e157a7 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi @@ -42,7 +42,7 @@ leds { compatible = "gpio-leds"; - blue { + led-blue { label = "n2:blue"; gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; @@ -410,7 +410,7 @@ &ext_mdio { external_phy: ethernet-phy@0 { - /* Realtek RTL8211F (0x001cc916) */ + /* Realtek RTL8211F (0x001cc916) */ reg = <0>; max-speed = <1000>; @@ -446,13 +446,58 @@ }; &gpio { + gpio-line-names = + /* GPIOZ */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* GPIOH */ + "", "", "", "", "", "", "", "", + "", + /* BOOT */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* GPIOC */ + "", "", "", "", "", "", "", "", + /* GPIOA */ + "PIN_44", /* GPIOA_0 */ + "PIN_46", /* GPIOA_1 */ + "PIN_45", /* GPIOA_2 */ + "PIN_47", /* GPIOA_3 */ + "PIN_26", /* GPIOA_4 */ + "", "", "", "", "", "", + "PIN_42", /* GPIOA_11 */ + "PIN_32", /* GPIOA_12 */ + "PIN_7", /* GPIOA_13 */ + "PIN_27", /* GPIOA_14 */ + "PIN_28", /* GPIOA_15 */ + /* GPIOX */ + "PIN_16", /* GPIOX_0 */ + "PIN_18", /* GPIOX_1 */ + "PIN_22", /* GPIOX_2 */ + "PIN_11", /* GPIOX_3 */ + "PIN_13", /* GPIOX_4 */ + "PIN_33", /* GPIOX_5 */ + "PIN_35", /* GPIOX_6 */ + "PIN_15", /* GPIOX_7 */ + "PIN_19", /* GPIOX_8 */ + "PIN_21", /* GPIOX_9 */ + "PIN_24", /* GPIOX_10 */ + "PIN_23", /* GPIOX_11 */ + "PIN_8", /* GPIOX_12 */ + "PIN_10", /* GPIOX_13 */ + "PIN_29", /* GPIOX_14 */ + "PIN_31", /* GPIOX_15 */ + "PIN_12", /* GPIOX_16 */ + "PIN_3", /* GPIOX_17 */ + "PIN_5", /* GPIOX_18 */ + "PIN_36"; /* GPIOX_19 */ /* * WARNING: The USB Hub on the Odroid-N2 needs a reset signal * to be turned high in order to be detected by the USB Controller * This signal should be handled by a USB specific power sequence * in order to reset the Hub when USB bus is powered down. */ - usb-hub { + hog-0 { gpio-hog; gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>; output-high; @@ -508,6 +553,11 @@ status = "okay"; }; +&saradc { + status = "okay"; + vref-supply = <&vddao_1v8>; +}; + /* SD card */ &sd_emmc_b { status = "okay"; |