diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts')
-rw-r--r-- | arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts | 63 |
1 files changed, 44 insertions, 19 deletions
diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts index 1e893c0b6fbc..852de624f5af 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts +++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts @@ -11,6 +11,7 @@ / { model = "Longcheer L8150"; compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916"; + chassis-type = "handset"; aliases { serial0 = &blsp1_uart2; @@ -30,14 +31,6 @@ }; }; - // FIXME: Use extcon device provided by charger driver when available - usb_vbus: usb-vbus { - compatible = "linux,extcon-usb-gpio"; - vbus-gpio = <&msmgpio 62 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&usb_vbus_default>; - }; - gpio-keys { compatible = "gpio-keys"; @@ -121,9 +114,21 @@ status = "okay"; accelerometer@10 { - compatible = "bosch,bmc150_accel"; + compatible = "bosch,bmc156_accel"; reg = <0x10>; + /* + * For some reason the interrupt line is usually not connected + * to the BMC156. However, there are two pads next to the chip + * that can be shorted to make it work if needed. + * + * interrupt-parent = <&msmgpio>; + * interrupts = <116 IRQ_TYPE_EDGE_RISING>; + */ + + pinctrl-names = "default"; + pinctrl-0 = <&accel_int_default>; + vdd-supply = <&pm8916_l17>; vddio-supply = <&pm8916_l6>; @@ -133,9 +138,15 @@ }; magnetometer@12 { - compatible = "bosch,bmc150_magn"; + compatible = "bosch,bmc156_magn"; reg = <0x12>; + interrupt-parent = <&msmgpio>; + interrupts = <113 IRQ_TYPE_EDGE_RISING>; + + pinctrl-names = "default"; + pinctrl-0 = <&magn_int_default>; + vdd-supply = <&pm8916_l17>; vddio-supply = <&pm8916_l6>; }; @@ -145,7 +156,8 @@ reg = <0x68>; interrupt-parent = <&msmgpio>; - interrupts = <23 IRQ_TYPE_EDGE_RISING>; + interrupts = <23 IRQ_TYPE_EDGE_RISING>, + <22 IRQ_TYPE_EDGE_RISING>; pinctrl-names = "default"; pinctrl-0 = <&gyro_int_default>; @@ -196,6 +208,10 @@ linux,code = <KEY_VOLUMEDOWN>; }; +&pm8916_usbin { + status = "okay"; +}; + &pm8916_vib { status = "okay"; }; @@ -225,11 +241,11 @@ &usb { status = "okay"; dr_mode = "peripheral"; - extcon = <&usb_vbus>; + extcon = <&pm8916_usbin>; }; &usb_hs_phy { - extcon = <&usb_vbus>; + extcon = <&pm8916_usbin>; }; &smd_rpm_regulators { @@ -336,6 +352,14 @@ }; &msmgpio { + accel_int_default: accel-int-default { + pins = "gpio116"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + camera_flash_default: camera-flash-default { pins = "gpio31", "gpio32"; function = "gpio"; @@ -361,25 +385,26 @@ }; gyro_int_default: gyro-int-default { - pins = "gpio23"; + pins = "gpio22", "gpio23"; function = "gpio"; drive-strength = <2>; bias-disable; }; - tp_int_default: tp-int-default { - pins = "gpio13"; + magn_int_default: magn-int-default { + pins = "gpio113"; function = "gpio"; drive-strength = <2>; bias-disable; }; - usb_vbus_default: usb-vbus-default { - pins = "gpio62"; + tp_int_default: tp-int-default { + pins = "gpio13"; function = "gpio"; - bias-pull-up; + drive-strength = <2>; + bias-disable; }; }; |